Comparison of column properties in reversed-phase chromatography: monolithic, cholesterolic and mixed bonded stationary phases

A commercial Chromolith C18 column and two new stationary phases with mixed ligands bonded on the Kromasil silica gel support, SG-MIX and SG-Chol, were characterized using simple tests based on the retention of non-polar, basic and acidic compounds. Polar and methylene selectivity tests in acetonitrile-water and methanol-water mobile phases revealed lower hydrophobicities of the SG-MIX and SG-Chol columns in comparison to the Chromolith column. The columns were further characterized using new test criteria - gradient oligomer capacity and isomeric selectivity and peak symmetry of naphthalene di-sulphonic acids in aqueous mobile phases. The cholesterolic column shows greater gradient oligomer selectivity for the separation of oligoethylene glycol samples than the SG-MIX and the Chromolith columns. Increased retention and peak tailing, but decreased isomeric selectivity for naphthalene-di-sulphonic acids was observed with the SG-MIX column, because of interactions with various polar bonded groups.     

Comparison of the performance of conventional microparticulates and monolithic reversed-phase columns for liquid chromatography separation of eleven pollutant phenols

The performance of isocratic separations of 11 pollutant phenols (PP) using monolithic (Chromolith RP-18e) and conventional reversed-phase 5 microm (Luna and Purospher C18) and 4 microm (Synergi C12) particulate size columns, selected from high purity silica materials, has been compared. The separations have been optimized based on a previously optimized separation in which a reversed-phase C18 Luna column and acetonitrile as organic modifier were used, allowing the separation of all phenols tested in 23 min. The optimization process was carried out for each column by studying the effect of the mobile phase (acetonitrile as organic modifier, pH, flow-rate) on phenols separation. Under the optimized separation conditions, all phenols were separated in less than 23 min for all columns tested. Asymmetry factors were further evaluated and used to estimate column efficiency using the Dorsey-Foley equation. The efficiency and asymmetry factors were lower for Chromolith than for Purospher and Luna columns respectively. The Chromolith column was finally selected, due to its lower flow resistance, analysis time and good efficiency and asymmetry factors. The PPs separation was achieved in 3 min. The asymmetry factors were in the range 0.9-1.5 using 50mM acetate buffer (pH = 5.25)-ACN (64:36, v/v) as mobile phase, T=45 degrees C and 4.0 ml min(-1) flow-rate.     

Methacrylate monolithic capillary columns for gradient peptide separations

For the separation of peptides with gradient-elution liquid chromatography a poly(butyl methacrylate-co-ethylene dimethacrylate) (BMA) monolithic capillary column was prepared and tested. The conditional peak capacity was used as a metric for the performance of this column, which was compared with a capillary column packed with C18-modified silica particles. The retention of the peptides was found to be smaller on the BMA column than on the particulate C18 column. To obtain the same retention in isocratic elution an approximately 15% (v/v) lower acetonitrile concentration had to be used in the mobile phase. The retention window in gradient elution was correspondingly smaller with the BMA column. The relation between peak width and retention under gradient conditions was studied in detail. It was found that in shallow gradients, with gradient times of 30min and more, the peak widths of the least retained compounds are strongly increased with the BMA column. This was attributed to the fact that these compounds migrate and elute with an unfavorable high retention factor. More retained compounds are eluted later in the gradient, but with a lower effective retention factor. With shallow gradients the peak capacity of the BMA column ( approximately 90) was clearly lower than that of a conventional packed column ( approximately 150). On the other hand, with steep gradients, when components elute with a low effective retention factor, the performance of the BMA column is relatively good. With a gradient time of 15min similar peak widths and thus similar peak capacities ( approximately 75) were found for the packed and the monolithic column. Two strategies were investigated to obtain higher peak capacities with methacrylate monolithic columns. The use of lauryl methacrylate (LMA) instead of butyl methacrylate (BMA) gave an increase in retention and narrower peaks for early eluting peptides. The peak capacity of the LMA column was approximately 125 in a 60min gradient. Another approach was to use a longer BMA column which resulted in a peak capacity of approximately 135 could be obtained in 60min.     

Comparison of commercial organic polymer‐based and silica‐based monolithic columns using mixtures of analytes differing in size and chemistry

Commercially available silica‐based monolithic columns Chromolith RP‐8e, Chromolith RP‐18, and Chromolith HR RP‐18, and polymer‐based monolithic columns ProSwift RP‐1S, ProSwift RP‐2H, and ProSwift RP‐3U varying in pore size and bonded phase have been tested for the fast separation of selected sets of analytes. These mixtures of analytes included small molecules (uracil, caffeine, 1‐phenylethanol, butyl paraben, and anthracene), acylated insulins, and intact proteins (ribonuclease A, cytochrome C, transferrin, apomyoglobin, and thyroglobulin), and covered wide range of chemistries and sizes. Small molecules were well separated with a height equivalent to theoretical plate of 11–26 μm using silica‐based monolithic columns, while organic polymer‐based monoliths excelled in the fast sub 1 min baseline separations of large molecules. A peak capacity of 37 was found for separation of acylated insulins on Chromolith columns using a 3 min gradient at a flow rate of 3 ml/min. Poor recovery of proteins from Chromolith columns and significant peak tailing of small molecules using ProSwift columns were the major obstacles in using monolithic columns in those applications.     

Comparison of monolithic and microparticulate columns for reversed-phase liquid chromatography of tryptic digests of industrial enzymes in cleaning products

Enzymes of several classes used in the formulations of cleaning products were characterized by trypsin digestion followed by HPLC with UV detection. A polymeric monolithic column (ProSwift) was used to optimize the separation of both the intact enzymes and their tryptic digests. This column was adequate for the quality control of raw industrial enzyme concentrates. Then, monolithic and microparticulate columns were compared for peptide analysis. Under optimized conditions, the analysis of tryptic digests of enzymes of different classes commonly used in the formulation of cleaning products was carried out. Number of peaks, peak capacity and global resolution were obtained in order to evaluate the chromatographic performance of each column. Particulate shell-core C18 columns (Kinetex, 2.6 μm) showed the best performance, followed by a silica monolithic column (Chromolith RP-18e) and the conventional C18 packings (Gemini, 5 μm or 3 μm). A polymeric monolithic column (ProSwift) gave the worst performances. The proposed method was satisfactorily applied to the characterization of the enzymes present in spiked detergent bases and commercial cleaners.     

Comparison of the performance of Chromolith Performance RP-18e, 1.8-μm Zorbax Eclipse XDB-C18 and XTerra MS C18, based on modelling approaches

Achievement of the highest separation efficiency and quick delivery of results are key requirements in liquid chromatography for enhancing productivity and reducing analysis cost, especially in the pharmaceutical industry. This work concerns two of the most popular current solutions to get fast separations: the use of a silica-based monolithic column (Chromolith Performance RP-18e) and a small-particle packed column (1.8-μm Zorbax Eclipse XDB-C18, which needs dedicated instruments allowing higher backpressures). Both columns succeeded in the full separation of phenols and β-adrenolytic drugs, which are compounds that interact with residual silanols, giving rise to wider peaks. The results were compared with those obtained with a special column designed to avoid silanol interaction, containing 5 μm particles (XTerra MS C18). Chromolith gave the shortest times at the expense of higher solvent consumption at the high flow rates needed. In contrast to other studies, comprehensive conclusions on the chromatographic performance, in terms of selectivity, peak shape, resolution, and analysis time, are derived from the inspection of the whole experimental domain using retention and peak shape modelling. In the literature, column comparison is usually carried out based on the performance for selected mobile phases (very often a single one), which offers deceiving results.     

Fast HPLC for quality control of Harpagophytum procumbens by using a monolithic silica column: method transfer from conventional particle-based silica column

The applicability of a monolithic C18-bonded silica column for the rapid HPLC separation of ingredients in medicinal plants and their phytopharmaceutical preparations has been evaluated in the author's laboratory. In this presentation, an existing method for the determination of the iridoid glycoside harpagoside in Harpagophytum procumbens (Devil's Claw) was successfully transferred from a conventional particle-based C18 silica column to a monolithic silica column. The very high porosity of the stationary phase allows chromatography with a much lower backpressure than on conventional columns. Therefore, the flow rate could be easily increased from 0.8 mL/min (particle-based column) to 5 mL/min (monolithic column) and the run-time reduced from 30 to 5 min (that is a reduction about 85% !), without losing any chromatographic resolution of the compound of interest. The amount of harpagoside was measured with the original method on a conventional particle-based silica column and on the adapted method on a monolithic silica column. The statistical mean t-test showed no significant differences of the variances and the means indicating that the fast HPLC method is an acceptable alternative. The shorter analysis time makes the method very valuable for commercial quality control of Harpagophytum extracts and its pharmaceutical preparations.     

反相硅胶整体柱离子对色谱法快速测定吡啶离子液体阳离子

建立了整体柱离子对色谱-紫外检测法梯度淋洗快速分离测定4种吡啶离子液体阳离子的方法。分离采用C18反相硅胶整体柱,以离子对试剂(用柠檬酸调节pH值)-乙腈为淋洗液,并采用多级梯度洗脱程序。实验考察了色谱柱、离子对试剂、乙腈浓度、色谱柱温度及流速对吡啶阳离子保留的影响,并讨论了其保留规律。咪唑阳离子的保留符合碳数规律。最佳色谱条件是:在流速3.0 mL/min,柱温30℃下,以1.0 mmol/L庚烷磺酸钠(pH 4.0)(A)+乙腈(B)为淋洗液进行梯度洗脱。淋洗梯度为0～2.0 min,10%B;2.0～2.5 min,10%～15%B;2.5～4.0 min,15%B;4.0～4.5 min,15%～20%B;4.5～10.0 min,20%B。在此条件下,4种吡啶阳离子可在7 min内基线分离。所测阳离子的检出限(S/N=3)为0.05～0.17 mg/L;峰面积的相对标准偏差(n=5)小于0.6%。将本方法用于实验室合成的离子液体样品和污水样品的分析,加标回收率在95.7%～99.0%之间。本方法准确、快速,具有较好的实用性。     

Comparison of LC Columns Packed with 2.6?��m Core-Shell and Sub-2?��m Porous Particles for Gradient Separation of Antibiotics

The recently introduced Kinetex C18 column packed with core-shell 2.6 ??m particles is declared to provide similar efficiency and short analysis as Acquity BEH C18 column with 1.7 ??m porous particles. Unlike Acquity BEH C18 column, Kinetex C18 column exhibited lower column backpressure making this column compatible to conventional LC systems. The performance of Kinetex C18 column (2.1 × 50 mm) and Acquity BEH C18 column (2.1 × 50 mm) for gradient separation of tetracyclines under acidic conditions (oxytetracycline, tetracycline, chlortetracycline, and doxycycline) and macrolides under alkaline conditions (tylosin, clarithromycin, roxithromycin, and carbomycin) was studied. The columns were compared by evaluation of their experimental peak capacity and its dependence on linear velocity and gradient slope. The maximal experimental peak capacities for analysis of tetracyclines were 51.8 (Acquity BEH C18 column) and 48.4 (Kinetex C18 column). This indicated that Kinetex C18 was a suitable alternative to Acquity BEH C18 column for the analysis of tetracyclines under acidic conditions. On the contrary, the maximal experimental peak capacities for analysis of macrolides on Acquity BEH C18 column was higher (46.7) than that on Kinetex C18 column (36.9). Moreover, application of Kinetex C18 column for the analysis of macrolides under alkaline conditions was limited with respect to its decreasing performance with growing number of injections on the column.     

Effects of column length, particle size, gradient length and flow rate on peak capacity of nano-scale liquid chromatography for peptide separations

The effects of the column length, the particle size, the gradient length and the flow rate of a nanoLC system on peptide peak capacity were investigated and compared. Columns packed with 1.7 microm and 3 microm C(18) materials into pieces of 75 microm capillary tubing of various lengths were tested with different gradient lengths and flow rates. While increasing the length of a column packed with the 1.7 microm material helped improve peptide peak capacity at the whole range of the tested gradient lengths (24-432 min), little improvement in peak capacity was observed with the increase of the length of a column packed with the 3 microm material unless a gradient longer than 50 min was carried out. Up to 30% of peak capacity increase was observed when a column's length is doubled, with little reduction in the throughput. In most cases, more than 50% of the increase in peak capacity was obtained with the reduction in the particle size from 3 microm to 1.7 microm. With the same backpressure generated, a shorter 1.7-microm-particle column outperformed a longer column packed with the 3 microm material. In a flow rate range of 100-700 nl/min, increasing the flow rate improved peak capacity for columns packed with 1.7 microm and 3 microm materials.     

Reversed-phase liquid chromatographic separation of antiretroviral drugs on a monolithic column using ionic liquids as mobile phase additives

The use of 3-methylimidazolium cation-based ionic liquids (ILs) was evaluated as mobile phase additives for separation of antiretroviral drugs on a monolithic column by RP-HPLC. Separation of eight commonly used antiretroviral drugs was achieved on a Chromolith Flash, RP-18e column (25 × 4.6 mm, porous material) using water (pH 4.0 adjusted with acetic acid)/methanol v/v as a mobile phase containing ILs in a gradient elution mode. The effects of concentrations of ILs on retention, resolution and peak shape were studied and a regression equation correlating the interactions between stationary phase and the ILs was established. The retention of all the drugs was decreased notably by using 1-butyl-3-methylimidazolium tetrafluoroborate, while 1-ethyl-3-methylimidazolium methylsulfate reduced gradient drift drastically when compared to triethylamine.     

Development and application of a high-performance liquid chromatography method using monolithic columns for the analysis of ecstasy tablets

A rapid and selective HPLC method using monolithic columns was developed for the separation and quantification of the principal amphetamines in ecstasy tablets. Three monolithic (Chromolith RP18e) columns of different lengths (25, 50 and 100 mm) were assessed. Validation studies including linearity, selectivity, precision, accuracy and limit of detection and quantification were carried out using the Chromolith SpeedROD, RP-18e, 50 mm x 4.6 mm column. Column backpressure and van Deemter plots demonstrated that monolithic columns provide higher efficiency at higher flow rates when compared to particulate columns without the loss of peak resolution. Application of the monolithic column to a large number of ecstasy tablets seized in Ireland ensured its suitability for the routine analysis of ecstasy tablets.     

Impact of pore structural parameters on column performance and resolution of reversed-phase monolithic silica columns for peptides and proteins

In this work, monolithic silica columns with the C4, C8, and C18 chemistry and having various macropore diameters and two different mesopore diameters are studied to access the differences in the column efficiency under isocratic elution conditions and the resolution of selected peptide pairs under reversed-phase gradient elution conditions for the separation of peptides and proteins. The columns with the pore structural characteristics that provided the most efficient separations are then employed to optimize the conditions of a gradient separation of a model mixture of peptides and proteins based on surface chemistry, gradient time, volumetric flow rate, and acetonitrile concentration. Both the mesopore and macropore diameters of the monolithic column are decisive for the column efficiency. As the diameter of the through-pores decreases, the column efficiency increases. The large set of mesopores studied with a nominal diameter of approximately 25 nm provided the most efficient column performance. The efficiency of the monolithic silica columns increase with decreasing n-alkyl chain length in the sequence of C18相似文献   

Development and validation of a UHPLC method for the determination of flavonoids in red wine

A simple and fast ultra-high-performance liquid chromatography (UHPLC) method was developed for the identification and quantification of the following flavonoids in red wine: (+/-)-catechin, (-)-epicatechin, rutin, quercitrin, hesperidin, neohesperidin, (+/-)-naringenin, hesperetin, and chrysin. Chromatographic separation of the flavonoids was performed on a Chromolith Fast Gradient C18e column. A gradient elution was used with mobile phases consisting of 0.1% formic acid in water and acetonitrile. UV detection was performed at 280 nm. A complete separation of flavonoids was possible within 6 min. The calibration curves showed good linearity (R2 > or = 0.9990) in the selected range of each analyte; the LOD ranged between 0.06 and 0.19 microg/mL. An optimized sample preparation method utilized SPE. The Oasis HLB column with the highest recoveries was selected for the preconcentration step. This method was successfully applied to the determination of these flavonoids in the red wine samples with excellent results.     

Quantitative determination of p-aminosalicylic acid and its degradation product m-aminophenol in pellets by ion-pair high-performance liquid chromatography applying the monolithic Chromolith Speedrod RP-18e column

An ion-pair high performance liquid chromatographic method was developed for the simultaneous determination of p-aminosalicylic acid (PAS) and its degradation product m-aminophenol (MAP) in a newly developed multiparticular drug delivery system. Owing to the concentration differences of PAS and MAP, acetanilide and sulfanilic acid were used as internal standards, respectively. The separation was performed on a Chromolith SpeedROD RP-18e column, a new packing material consisting of monolithic rods of highly porous silica. The mobile phase composition was of 20 mm phosphate buffer, 20 mm tetrabutylammonium hydrogen sulphate and 16% (v/v) methanol adjusted to pH 6.8, at a flow-rate of 1.0 mL/min, resulting in a run-time of about 6 min. Detection was by UV at 233 nm. The method was validated and proved to be useful for stability testing of the new dosage form. Separation efficiency was compared between the new packing material Chromolith SpeedROD RP-18e and the conventional reversed-phase cartridge LiChroCART 125-4 (5 microm). A robustness test was carried out on both columns and different separation parameters (retention, resolution, run time, temperature) were determined.     

Fast determination of tetrafluoroborate by high-performance liquid chromatography using a monolithic column

Fast determination of tetrafluoroborate by high-performance liquid chromatography using a silica-based monolithic column and direct conductivity detection was carried out. Chromatographic separation was performed on a Chromolith Speed ROD RP-18e column (50 mm x 4.6 mm i.d.) with tetrabutylammonium hydroxide (TBA-OH)+ phthalic acid as eluent. The effects of eluent concentration, eluent pH, column temperature and flow rate on retention time of tetrafluoroborate were investigated. The optimized chromatographic conditions for determination of tetrafluoroborate were using 0.5mM TBA-OH + 0.31 mM phthalic acid (pH 5.5) as eluent, column temperature of 30 degrees C and flow rate of 6.0 mL/min. Retention time of tetrafluoroborate was less than 1min under the conditions. Common anions (Cl(-), Br(-), NO3(-) and SO4(2-)) did not interfere with the determination of tetrafluoroborate. Detection limit (S/N = 2) for tetrafluoroborate was 1.4 mg/L. The linear range of calibration curve between peak area and the concentration of tetrafluoroborate was from 1.4 to 100.0 mg/L. The reproducibility was 0.09% and 1.8% (n = 5) relative standard deviation (RSD) for retention time and peak area, respectively. The method has been applied to the determination of tetrafluoroborate in ionic liquids. Recoveries of tetrafluoroborate after spiking were 98.2-101.5%.     

Rapid separation of chlorophylls a and b and their demetallated and dephytylated derivatives using a monolithic silica C18 column and a pyridine-containing mobile phase

A monolithic C18-bonded silica rod column (Merck Chromolith) was applied to the separation of mixtures of chlorophylls a and b and their derivatives originated by hydrolysis of the phytyl ester linkage (chlorophyllides), loss of the central Mg atom (pheophytins), or both processes (pheophorbides). Mobile phases containing two different ion-pair reagents, ammonium acetate and buffered pyridine, were tested. Both eluents achieved the resolution of the eight pigments in less than 5 min. The method based on the pyridine-containing mobile phase was applied to the separation of chlorophylls and their green coloured degradation products in senescing leaves of deciduous trees, green fruits and a marine microalga.     

Advantages of ultra performance liquid chromatography over high-performance liquid chromatography: comparison of different analytical approaches during analysis of diclofenac gel

Miniaturization embracing instrumentation, column particle size, and column dimensions is one of the major current trends in separation techniques. This leads to shortening of analysis time and great savings in solvent consumption. Ultra performance liquid chromatography (UPLC) is one of the new developments in liquid chromatography. An ultra-high pressure system allows using of small particle-packed columns with small diameter, which has a positive effect on both system efficiency and analysis time. An analytical method for determination of the active substance diclofenac, the degradation product 1-(2,6-dichlorphenyl)-2-indolinone, and the preservatives methylparaben and propylparaben was used for testing and comparing LC systems. Various octadecylsilica-based analytical columns were examined. Acquity UPLC BEH C18 (2.1 x 50 mm, 1.7 microm) and (2.1 x 100 mm, 1.7 microm) were tested for UPLC. The following analytical columns were used in a test for HPLC: Purospher RP 18e (125 x 4.0 mm, 5 microm), Zorbax Eclipse XDB C18 (75 x 4.6 mm, 3.5 microm), Zorbax Eclipse SB C18 (50 x 4.6 mm, 1.8 microm), as was a monolithic column (Chromolith Performance RP-18e (100 x 4.6 mm). Results of a System Suitability Test (SST) were calculated and compared for each chromatographic peak. System efficiency and analysis duration were compared with regard to solvent consumption and system maintenance     

High‐resolution peptide separations using nano‐LC at ultra‐high pressure

We report on the optimization of nano‐LC gradient separations of proteomic samples that vary in complexity. The gradient performance limits were visualized by kinetic plots depicting the gradient time needed to achieve a certain peak capacity, while using the maximum system pressure of 80 MPa. The selection of the optimal particle size/column length combination and corresponding gradient steepness was based on scouting the performance of 75 μm id capillary columns packed with 2, 3, and 5 μm fully porous silica C18 particles. At optimal gradient conditions, peak capacities up to 500 can be obtained within a 120 min gradient using 2 μm particle‐packed capillary columns. Separations of proteomic samples including a cytochrome c tryptic digest, a bovine serum albumin tryptic digest, a six protein mix digest, and an Escherichia coli digest are demonstrated while operating at the kinetic‐performance limit, i.e. using 2‐μm packed columns, adjusting the column length and scaling the gradient steepness according to sample complexity. Finally, good run‐to‐run retention time stability (RSD values below 0.18%) was demonstrated applying ultra‐high pressure conditions.     

Approaches to characterise chromatographic column performance based on global parameters accounting for peak broadening and skewness

Peak broadening and skewness are fundamental parameters in chromatography, since they affect the resolution capability of a chromatographic column. A common practice to characterise chromatographic columns is to estimate the efficiency and asymmetry factor for the peaks of one or more solutes eluted at selected experimental conditions. This has the drawback that the extra-column contributions to the peak variance and skewness make the peak shape parameters depend on the retention time. We propose and discuss here the use of several approaches that allow the estimation of global parameters (non-dependent on the retention time) to describe the column performance. The global parameters arise from different linear relationships that can be established between the peak variance, standard deviation, or half-widths with the retention time. Some of them describe exclusively the column contribution to the peak broadening, whereas others consider the extra-column effects also. The estimation of peak skewness was also possible for the approaches based on the half-widths. The proposed approaches were applied to the characterisation of different columns (Spherisorb, Zorbax SB, Zorbax Eclipse, Kromasil, Chromolith, X-Terra and Inertsil), using the chromatographic data obtained for several diuretics and basic drugs (β-blockers).