Can delignification decrease cellulose digestibility in acid pretreated corn stover?

It has previously been shown that the improved digestibility of dilute acid pretreated corn stover is at least partially due to the removal of xylan and the consequent increase in accessibility of the cellulose to cellobiohydrolase enzymes. We now report on the impact that lignin removal has on the accessibility and digestibility of dilute acid pretreated corn stover. Samples of corn stover were subjected to dilute sulfuric acid pretreatment with and without simultaneous (partial) lignin removal. In addition, some samples were completely delignified after the pretreatment step using acidified sodium chlorite. The accessibility and digestibility of the samples were tested using a fluorescence-labeled cellobiohydrolase (Trichoderma reesei Cel7A) purified from a commercial cellulase preparation. Partial delignification of corn stover during dilute acid pretreatment was shown to improve cellulose digestibility by T. reesei Cel7A; however, decreasing the lignin content below 5% (g g⁻¹) by treatment with acidified sodium chlorite resulted in a dramatic reduction in cellulose digestibility. Importantly, this effect was found to be enhanced in samples with lower xylan contents suggesting that the near complete removal of xylan and lignin may cause aggregation of the cellulose microfibrils resulting in decreased cellulase accessibility.     

Optimization of steam pretreatment of corn stover to enhance enzymatic digestibility

Among the available agricultural byproducts, corn stover, with its yearly production of 10 million t (dry basis), is the most abundant promising raw material for fuel ethanol production in Hungary. In the United States, more than 216 million to fcorn stover is produced annually, of which a portion also could possibly be collected for conversion to ethanol. However, a network of lignin and hemicellulose protects cellulose, which is the major source of fermentable sugars in corn stover (approx 40% of the dry matter [DM]). Steam pretreatment removes the major part of the hemicellulose from the solid material and makes the cellulose more susceptible to enzymatic digestion. We studied 12 different combinations of reaction temperature, time, and pH during steam pretreatment. The best conditions (200°C, 5 min, 2% H₂SO₄) increased the enzymatic conversion (from cellulose to glucose) of corn stover more then four times, compared to untreated material. However, steam pretreatment at 190°C for 5 min with 2% sulfuric acid resulted in the highest overall yield of sugars, 56.1 g from 100 g of untreated material (DM), corresponding to 73% of the theoretical. The liquor following steam explosion was fermented using Saccharomyces cerevisiae to investigate the inhibitory effect of the pretreatment. The achieved ethanol yield was slightly higher than that obtained with a reference sugar solution. This demonstrates that baker's yeast could adapt to the pretreated liquor and ferment the glucose to ethanol efficiently.     

Effects of temperature and moisture on dilute-acid steam explosion pretreatment of corn stover and cellulase enzyme digestibility

Corn stover is emerging as a viable feedstock for producing bioethanol from renewable resources. Dilute-acid pretreatment of corn stover can solubilize a significant portion of the hemicellulosic component and enhance the enzymatic digestibility of the remaining cellulose for fermentation into ethanol. In this study, dilute H₂SO₄ pretreatment of corn stover was performed in a steam explosion reactor at 160°C, 180°C, and 190°C, approx 1 wt% H₂SO₄, and 70-s to 840-s residence times. The combined severity (Log₁₀ [R _o ] - pH), an expression relating pH, temperature, and residence time of pretreatment, ranged from 1.8 to 2.4. Soluble xylose yields varied from 63 to 77% of theoretical from pretreatments of corn stover at 160 and 180°C. However, yields >90% of theoretical were found with dilute-acid pretreatments at 190°C. A narrower range of higher combined severities was required for pretreatment to obtain high soluble xylose yields when the moisture content of the acid-impregnated feedstock was increased from 55 to 63 wt%. Simultaneous saccharification and fermentation (SSF) of washed solids from corn stover pretreated at 190°C, using an enzyme loading of 15 filter paper units (FPU)/g of cellulose, gave ethanol yields in excess of 85%. Similar SSF ethanol yields were found using washed solid residues from 160 and 180°C pretreatments at similar combined severities but required a higher enzyme loading of approx 25 FPU/g of cellulose.     

Effect of sulfuric and phosphoric acid pretreatments on enzymatic hydrolysis of corn stover

The pretreatment of corn stover with H₂SO₄ and H₃PO₄ was investigated. Pretreatments were carried out from 30 to 120 min in a batch reactor at 121°C, with acid concentrations ranging from 0 to 2% (w/v) at a solid concentration of 5% (w/v). Pretreated corn stover was washed with distilled water until the filtrate was adjusted to pH 7.0, followed by surfactant swelling of the cellulosic fraction in a 0–10% (w/v) solution of Tween-80 at room temperature for 12 h. The dilute acid treatment proved to be a very effective method in terms of hemicellulose recovery and cellulose digetibility. Hemicellulose recovery was 62–90%, and enzymatic digestibility of the cellulose that remained in the solid was >80% with 2% (w/v) acid. In all cases studied, the performance of H₂SO₄ pretreatment (hemicellulose recovery and cellulose digestibility) was significantly better than obtained with H₃PO₄. Enzymatic hydrolysis was more effective using surfactant than without it, producing 10–20% more sugar. Furthermore, digestibility was investigated as a function of hemicellulose removal. It was found that digestibility was more directly related to hemicellulose removal than to delignification.     

Microbial Pretreatment of Corn Stovers by Solid-State Cultivation of Phanerochaete chrysosporium for Biogas Production

The microbial pretreatment of corn stover and corn stover silage was achieved via the solid-state cultivation of Phanerochaete chrysosporium; pretreatment effects on the biodegradability and subsequent anaerobic production of biogas were investigated. The peak levels of daily biogas production and CH₄ yield from corn stover silage were approximately twice that of corn stover. Results suggested that ensiling was a potential pretreatment method to stimulate biogas production from corn stover. Surface morphology and Fourier-transform infrared spectroscopy analyses demonstrated that the microbial pretreatment of corn stover silage improved biogas production by 10.5 to 19.7 % and CH₄ yield by 11.7 to 21.2 % because pretreatment could decrease dry mass loss (14.2 %) and increase substrate biodegradability (19.9 % cellulose, 32.4 % hemicellulose, and 22.6 % lignin). By contrast, the higher dry mass loss in corn stover (55.3 %) after microbial pretreatment was accompanied by 54.7 % cellulose, 64.0 % hemicellulose, and 61.1 % lignin degradation but did not significantly influence biogas production.     

Enzymatic production of xylooligosaccharides from corn stover and corn cobs treated with aqueous ammonia

A novel method of producing food-grade xylooligosaccharides from corn stover and corn cobs was investigated. The process starts with pretreatment of feedstock in aqueous ammonia, which results delignified and xylan-rich substrate. The pretreated substrates are subjected to enzymatic hydrolysis of xylan using endoxylanase for production of xylooligosaccharides. The conventional enzyme-based method involves extraction of xylan with a strong alkaline solution to form a liquid intermediate containing soluble xylan. This intermediate is heavily contaminated with various extraneous components. A costly purification step is therefore required before enzymatic hydrolysis. In the present method, xylan is obtained in solid form after pretreatment. Water-washing is all that is required for enzymatic hydrolysis of this material. The complex step of purifying soluble xylan from contaminant is essentially eliminated. Refining of xylooligosaccharides to food-grade is accomplished by charcoal adsorption followed by ethanol elution. Xylanlytic hydrolysis of the pretreated corn stover yielded glucan-rich residue that is easily digestible by cellulase enzyme. The digestibility of the residue reached 86% with enzyme loading of 10 filter paper units/g-glucan. As a feedstock for xylooligosaccharides production, corn cobs are superior to corn stover because of high xylan content and high packing density. The high packing density of corn cobs reduces water input and eventually raises the product concentration.     

Influence of ionic-liquid incubation temperature on changes in cellulose structure,biomass composition,and enzymatic digestibility

Varying ionic liquid, 1-ethyl 3-methyl imidazolium acetate, pretreatment incubation temperature on lignocellulosic biomass substrates, corn stover, switchgrass and poplar, can have dramatic effects on the enzymatic digestibility of the resultant regenerated biomass. In order to delineate the chemical and physical changes resulting from the pretreatment process and correlate changes with enzymatic digestibility, X-ray powder and fiber diffraction, ¹³C cross polarization/magic angle spinning nuclear magnetic resonance spectroscopy, and compositional analysis was completed on poplar, corn stover and switchgrass samples. Optimal pretreatment incubation temperatures were most closely associated with the retention of amorphous substrates upon drying of regenerated biomass. Maximal glucan to glucose conversion for 24 h enzyme hydrolysis was observed for corn stover, switchgrass and poplar at ionic liquid incubation temperatures of 100, 110 and 120 °C, respectively. We hypothesize that effective pretreatment temperatures must attain lignin redistribution and retention of xylan for optimal enzyme digestibility.     

Enhancing the Enzymatic Hydrolysis of Corn Stover by an Integrated Wet-milling and Alkali Pretreatment

An integrated wet-milling and alkali pretreatment was applied to corn stover prior to enzymatic hydrolysis. The effects of NaOH concentration in the pretreatment on crystalline structure, chemical composition, and reducing-sugar yield of corn stover were investigated, and the mechanism of increasing reducing-sugar yield by the pretreatment was discussed. The experimental results showed that the crystalline structure of corn stover was disrupted, and lignin was removed, while cellulose and hemicellulose were retained in corn stover by the pretreatment with 1% NaOH in 1 h. The reducing-sugar yield from the pretreated corn stovers increased from 20.2% to 46.7% when the NaOH concentration increased from 0% to 1%. The 1% NaOH pretreated corn stover had a holocellulose conversion of 55.1%. The increase in reducing-sugar yield was related to the crystalline structure disruption and delignification of corn stover. It was clarified that the pretreatment significantly enhanced the conversion of cellulose and hemicellulose in the corn stover to sugars.     

Two-stage dilute-acid pretreatment of softwoods

Whole treechips obtained from softwood forest thinnings were pretreated via single-and two-stage dilute-sulfuric acid pretreatment. Whole-tree chips were impregnated with dilute sulfuric acid and steam treated in a 4-L steam explosion reactor. In single-stage pretreatment, wood chips were treated using a wide range of severity. In two-stage pretreatment, the first stage was carried out at low severity tomaximize hemicellulose recovery. Solubilized sugars were recovered from the first-stage prehydrolysate by washing with water. In the second stage, water-insoluble solids from first-stage prehydrolysate were impregnated with dilute sulfuric acid, then steam treated at more severe conditions to hydrolyze a portion of the remaining cellulose to glucose and to improve the enzyme digestibility. The total sugar yields obtained after enzymatic hydrolysis of two-stage dilute acid-pretreated samples were compared with sugar yields from single-stage pretreatment. The overall sugar yield from two-stage dilute-acid pretreatment was approx 10% higher, and the net enzyme requirement was reduced by about 50%. Simultaneous saccharification and fermentation using an adapted Saccharomyces cerevisiae yeast strain further improved cellulose conversion yield and lowered the enzyme requirement.     

Pretreatment of corn stover using wet oxidation to enhance enzymatic digestibility

Corn stover is an abundant, promising raw material for fuel ethanol production. Although it has a high cellulose content, without pretreatment it resists enzymatic hydrolysis, like most lignocellulosic materials. Wet oxidation (water, oxygen, mild alkali or acid, elevated temperature and pressure) was investigated to enhance the enzymatic digestibility of corn stover. Six different combinations of reaction temperature, time, and pH were applied. The best conditions (60g/L of corn stover, 195°C, 15 min, 12 bar O₂, 2 g/L of Na₂CO₃) increased the enzymatic conversion of corn stover four times, compared to untreated material. Under these conditions 60% of hemicellulose and 30% of lignin were solubilized, whereas 90% of cellulose remained in the solid fraction. After 24-h hydrolysis at 50°C using 25 filter paper units (FPU)/g of dry matter (DM) biomass, the achieved conversion of cellulose to glucose was about 85%. Decreasing the hydrolysis temperature to 40°C increased hydrolysis time from 24 to 72 h. Decreasing the enzyme loading to 5 FPU/g of DM biomass slightly decreased the enzymatic conversion from 83.4 to 71%. Thus, enzyme loading can be reduced without significantly affecting the efficiency of hydrolysis, an important economical aspect.     

Pretreatment of corn stover by soaking in aqueous ammonia

Soaking in aqueous ammonia (SAA) was investigated as a pretreatment method for corn stover. In this method, the feedstock was soaked in aqueous ammonia over an extended period (10–60 d) at room temperature. It was done without agitation at atmospheric pressure. SAA treatment removed 55–74% of the lignin, but retained nearly 100% of the glucan and 85% of the xylan. The xylan remaining in the corn stover after SAA treatment was hydrolyzed along with the glucan by xylanase present in the Spezyme CP enzyme. In the simultaneous saccharification and fermentation (SSF) test of SAA-treated corn stover, using S. cerevisiae (D₅A), an ethanol yield of 73% of theoretical maximum was obtained on the basis of the glucan content in the treated corn stover. The accumulation of xylose in the SSF appears to inhibit the cellulase activity on glucan hydrolysis, which limits the yield of ethanol. In the simultaneous saccharification and co-fermentation (SSCF) test, using recombinant E. coli (KO11), both the glucan and xylose were effectively utilized, resulting in on overall ethanol yield of 77% based on the glucan and xylan content of the substrate. When the SSCF process is used, the fact that the xylan fraction is retained during pretreatment is a desirable feature since the overall bioconversion can be carried out in a single step without separate recovery of xylose from the pretreatment liquid.     

Effect of corn stover concentration on rheological characteristics

Corn stover, a well-known example of lignocellulosic biomass, is a potential renewable feed for bioethanol production. Dilute sulfuric acid pretreatment removes hemicellulose and makes the cellulose more susceptible to bacterial digestion. The rheologic properties of corn stover pretreated in such a manner were studied. The Power Law parameters were sensitive to corn stover suspension concentration becoming more non-Newtonian with slope n, ranging from 0.92 to 0.05 between 5 and 30% solids. The Casson and the Power Law models described the experimental data with correlation coefficients ranging from 0.90 to 0.99 and 0.85 to 0.99, respectively. The yield stress predicted by direct data extrapolation and by the Herschel-Bulkley model was similar for each concentration of corn stover tested.     

Pretreatment of corn stover by low-liquid ammonia recycle percolation process

A pretreatment method using aqueous ammonia was investigated with the intent of minimizing the liquid throughput. This process uses a flow-through packed column reactor (or percolation reactor). In comparison to the ammonia recycle percolation (ARP) process developed previously in our laboratory, this process significantly reduces the liquid throughput to one reactor void volume in packed bed (2.0–4.7 mL of liquid/g of corn stover) and, thus, is termed low-liquid ARP (LLARP). In addition to attaining short residence time and reduced energy input, this process achieves 59–70% of lignin removal and 48–57% of xylan retention. With optimum operation of the LLARP to corn stover, enzymatic digestibilities of 95, 90 and 86% were achieved with 60, 15, and 7.5 filter paper units/g of glucan, respectively. In the simultaneous saccharification and fermentation test of the LLARP samples using Saccharomyces cerevisiae (NREL-D₅A), an ethanol yield of 84% of the theoretical maximum was achieved with 6% (w/v) glucan loading. In the simultaneous saccharification and cofermentation (SSCF) test using recombinant Escherichia coli (KO11), both the glucan and xylan in the solid were effectively utilized, giving an overall ethanol yield of 109% of the theoretical maximum based on glucan, a clear indication that the xylan content was converted into ethanol. The xylooligomers existing in the LLARP effluent were not effectively hydrolyzed by cellulase enzyme, achieving only 60% of digestibility. SSCF of the treated corn stover was severely hampered when the substrate was supplemented with the LLARP effluent, giving only 56% the overall yield of ethanol. The effluent appears to significantly inhibit cellulase and microbial activities.     

Hydrolyzabilities of Different Corn Stover Fractions After Aqueous Ammonia Pretreatment

The effect of aqueous ammonia pretreatment on the hydrolysis of different corn stover fractions (rind, husk, leaf, and pith) by xylanase (XYL) with cellulases (CELs) was evaluated. The aqueous ammonia pretreatment had excellent delignification ability (above 66 %) for different corn stover fractions. The corn rind exhibited the lowest susceptibility to aqueous ammonia pretreatment. The pretreated rind showed the lowest hydrolyzability by CEL and XYL, which was supported by a high content of crystalline cellulose in the hydrolyzed residues of rind, as confirmed by X-ray diffraction (XRD). With the addition of 1 mg XYL/g dry matter, a high glucose yield (above 90 %) could be obtained from the pretreated rind by CEL. The results revealed that a high hydrolyzate yield of corn rind after aqueous ammonia pretreatment could be obtained with 1 mg xylanase/g dry matter, showing that aqueous ammonia pretreatment and xylanase addition to cellulases have great potential for the efficient hydrolysis of corn stover without previous fractionation.     

Effects of Low Moisture Anhydrous Ammonia (LMAA) Pretreatment at Controlled Ammoniation Temperatures on Enzymatic Hydrolysis of Corn Stover

Corn stover was treated using low-moisture anhydrous ammonia (LMAA) at controlled ammoniation temperature. Moisturized corn stover (50 % moisture) was contacted with anhydrous ammonia (0.1 g NH₃/g-biomass) in a batch reactor at various temperatures (ambient to 150 °C). After ammoniation at elevated and controlled temperature, ammoniated corn stover was pretreated at various temperatures (60–150 °C) for 72–144 h. Change in composition was marginal at low pretreatment temperature but was relatively severe with pretreatment at high temperature (130–150 °C). The latter resulted in low enzymatic digestibility. It was also observed that extreme levels (either high or low) of residual ammonia affected enzymatic digestibility, while residual ammonia improved by 1.0–1.5 %. The LMAA method enhanced enzymatic digestibility compared to untreated corn stover (29.8 %). The highest glucan and xylan digestibility (84.1 and 73.6 %, respectively) was obtained under the optimal LMAA conditions (i.e., ammoniation at 70 °C for 20 min, followed by pretreatment at 90 °C for 48 h).     

Chemical pretreatments of corn stover for enhancing enzymatic digestibility

Corn stover, the most abundant agricultural residue in Hungary, is a potential raw material for the production of fuel ethanol as a result of its high content of carbohydrates, but a pretreatment is required for its efficient hydrolysis. In this article, we describe the results using various chemicals such as dilute H₂SO₄, HCl, and NaOH separately as well as consecutively under relative mild conditions (120°C, 1h). Pretreatment with 5% H₂SO₄ or 5% HCl solubilized 85% of the hemicellulose fraction, but the enzymatic conversion of pretreated materials increased only two times compared to the untreated corn stover. Applying acidic pretreatment following a 1-d soaking in base achieved enzymatic conversion that was nearly the theoretical maximum (95.7%). Pretreatment with 10% NaOH decreased the lignin fraction >95%, increased the enzymatic conversion more than four times, and gave a 79.4% enzymatic conversion. However, by increasing the reaction time, the enzymatic degradability could also be increased significantly, using a less concentrated base. When the time of pretreatment was increased three times (0.5% NaOH at 120°C), the amount of total released sugars was 47.9 g from 100 g (dry matter) of untreated corn stover.     

Enhanced saccharification of lignocellulosic biomass with1-allyl-3-methylimidazolium chloride（Amim Cl） pretreatment

A simple and efficient method of enhancing biomass saccharification by microwave-assisted pretreatment with dimethyl sulfoxide/1-allyl-3-methylimidazolium chloride is proposed. Softwood（pine wood（PW））, hardwoods（poplar wood, catalpa bungi, and Chinese parasol）, and agricultural wastes（rice straw, wheat straw, and corn stover（CS）） were exploited. Results showed that the best pretreatment effect was in PW with 54.3% and 31.7% dissolution and extraction ratios, respectively. The crystal form of cellulose in PW extract transformed from I to II, and the contended cellulose ratio and glucose conversion ratio reached 85.1% and 85.4%, respectively. CS after steam explosion achieved a similar pretreating effect as PW, with its cellulose hydrolysis ratio reaching as high as 91.5% after IL pretreatment.     

Pretreatment and Fractionation of Corn Stover by Soaking In Ethanol and Aqueous Ammonia

A new process for pretreatment of lignocellulosic biomass, designated the soaking in ethanol and aqueous ammonia (SEAA) process, was developed to improve hemicellulose preservation in solid form. In the SEAA process, an aqueous ammonia solution containing ethanol is used. Corn stover was treated with 15 wt.% ammonia at 1:9 solid–liquid ratio (by weight) at 60 °C for 24 h with ethanol added at 1, 5, 20, and 49 wt.% (balance was water). The extents by which xylan was solubilized with no ethanol and with ethanol added at 1, 5, 20, and 49 wt.% of the total liquid were 17.2%, 16.7%, 14.5%, 10.4%, and 6.3% of the original xylan, respectively. Thus, at the highest ethanol concentration used the loss of hemicellulose to the liquid phase was reduced by 63%. The digestibility of glucan and xylan in the pretreated corn stover samples by cellulase was not affected by ethanol addition of up to 20 wt.%. The enzymatic digestibility of the corn stover treated with 49 wt.% ethanol added was lower than the digestibility of the sample treated with no ethanol addition. Thus, based on these results, 20 wt.% was found to be the optimum ethanol concentration for use in the SEAA process for pretreatment of corn stover.     

Autohydrolysis of Tropical Agricultural Residues by Compressed Liquid Hot Water Pretreatment

Pretreatment is an essential step in biorefineries for improving digestibility of recalcitrant agricultural feedstocks prior to enzymatic hydrolysis to composite sugars, which can be further converted to fuels and chemicals. In this study, autohydrolysis by compressed liquid hot water (LHW) pretreatment of various tropical agricultural residues including sugarcane bagasse (BG), rice straw (RS), corn stover (CS), and empty palm fruit bunch (EPFB) was investigated. It was found that LHW pretreatment at 200 °C for 5–20 min resulted in high levels of hemicellulose solubilization into the liquid phase and marked improvement on enzymatic digestibility of the solid cellulose-enriched residues. The maximal yields of glucose and pentose were 409.8–482.7 mg/g and 81.1–174.0 mg/g of pretreated substrates, respectively. Comparative analysis based on severity factor showed varying susceptibility of biomass to LHW in the order of BG> RS> CS> EPFB. Structural analysis revealed surface modification of the pretreated biomass along with an increase in crystallinity index. Overall, 75.7–82.3 % yield of glucose and 27.4–42.4 % yield of pentose from the dried native biomass was recovered in the pretreated solid residues, while 18.3–29.7 % of pentoses were recovered in the liquid phase with dehydration by-product concentration under the threshold for ethanologens. The results suggest the potential of LHW as an efficient pretreatment strategy for implementation in biorefineries operated using various seasonal agricultural feedstocks.     

Cellulose solvent-based pretreatment for corn stover and avicel: concentrated phosphoric acid versus ionic liquid [BMIM]Cl

Since cellulose accessibility has become more recognized as the major substrate characteristic limiting hydrolysis rates and glucan digestibilities, cellulose solvent-based lignocellulose pretreatments have gained attention. In this study, we employed cellulose solvent- and organic solvent-based lignocellulose fractionation using two cellulose solvents: concentrated phosphoric acid [~85?% (w/w) H₃PO₄] and an ionic liquid Butyl-3-methylimidazolium chloride ([BMIM]Cl). Enzymatic glucan digestibilities of concentrated phosphoric acid- and [BMIM]Cl-pretreated corn stover were 96 and 55?% after 72?h at five filter paper units of cellulase per gram of glucan, respectively. Regenerated amorphous cellulose by concentrated phosphoric acid and [BMIM]Cl had digestibilities of 100 and 92?%, respectively. Our results suggested that differences in enzymatic glucan digestibilities of concentrated phosphoric acid- and [BMIM]Cl-pretreated corn stover were attributed to combinatory factors. These results provide insights into mechanisms of cellulose solvent-based pretreatment and effects of residual cellulose solvents and lignin on enzymatic cellulose hydrolysis.