Regenerated fibre Bragg grating fabricated on high germanium concentration photosensitive fibre for sensing at high temperature

A Regenerated Fibre Bragg Grating (RFBG), with repeatable high temperature response between 400 °C–1200 °C, has been demonstrated using a hydrogen-loaded, highly germanium-doped, photosensitive fibre. A wavelength shifts of as much as 20 nm is attained during temperature calibration up to 1300 °C. A large temperature response of 17 pm/°C is obtained from the RFBG, with very good repeatability.     

传送带类问题归类分析

本文中的传送带类问题是指以皮带传送装置(传送带)为载体而构建的各类物理问题．传送带类问题丰富多彩，能够很好地再现物理知识和考查各种能力，因而值得我们分类探究．     

光纤光栅温度传感实验

为适应高等院校电子、通讯、信息技术等专业实验教学的需要，设计了光纤光栅温度传感实验．通过该实验，学生可以了解光纤光栅传感器的原理及解调的方法．     

温度不敏感的光纤布拉格高压传感技术研究

 为了实现单一光纤光栅对压强精确测量,设计了一种温度不敏感的光纤布拉格高压传感器。对该传感器的温度特性及压强响应特性进行研究。给出了该传感器的结构及封装方法。从理论上分析了该传感器的温度去敏原理,推导了该压强传感器的光纤布拉格光栅中心波长与压强的关系,得到了该传感器的压强响应灵敏度的解析表达。通过实验分析传感器的温度特性及压强响应。实验结果表明,在21℃～260.8℃的范围内,实现了温度补偿,平均波长漂移量为0.75 pm/℃,在0～44 MPa的范围内,获得了-0.054 8 nm/MPa的压强响应灵敏度,是裸光纤布拉格光栅压力响应灵敏度的18.27倍。该传感器的压强响应具有很好的线性和重复性,实验值与理论值吻合得很好,该传感器能够通过一只光纤布拉格光栅实现压强的精确测量。     

飞秒激光刻写的超短光纤布拉格光栅及其传感特性

为了提高光纤光栅传感器的测量精度及可靠性,实现点式测量,拓宽光纤布拉格光栅(FBG)的应用,本文提出了基于飞秒激光直写扫线技术制备超短FBG。首先,在单模光纤上制备了周期为5.35μm、长度为53.5μm的超短FBG,其温度和应力的灵敏度分别为0.011 nm/℃和1.509 nm/N;然后,用体积分数为4%的氢氟酸对制备超短FBG进行选择性腐蚀,制备出了微通道超短FBG,并研究了它对NaCl溶液的传感特性,其折射率灵敏度为69.11 nm/RIU。结果表明,这种微通道超短FBG具有高重复性、高可靠性、可多参数测量等优点。     

匹配光纤光栅温度传感解调系统

实验了一种基于一维调节器的光纤光栅静态温度(温度缓变)探测系统。在系统中,一维调节器与步进电机相连,步进电机由PC(计算机)通过PLC(可编程逻辑控制器)进行控制,匹配光纤光栅被固定在一维调节器上用来解调增敏光纤光栅传感器探测到的温度信号,匹配光栅的Bragg周期可通过调节一维调节器进行控制,其透射的光信号经光电检测电路检测并与调节架形成闭环控制。实验测得,在10℃~70℃范围内系统温度传感探测精度为±0.3℃。     

Distributed three-dimensional fiber Bragg grating refractometer for biochemical sensing

We demonstrate a three-dimensional (3-D) distributed refractometer that measures refractive index in a small volume. The sensor is based on an evanescent-wave fiber Bragg grating that is interrogated by low-coherence spectral interferometry. The measurement can be performed on a short time scale without the need for a mechanical scan. The new sensor was used to simultaneously measure glucose concentration in several droplets along a single sensor and to interrogate the time-dependent evaporation process of a water droplet. The new measurement technique might enable novel 3-D distributed sensors to be developed and multiple discrete measurements to be made in a small volume.     

Temperature-insensitive fiber Bragg grating dynamic pressure sensing system

Temperature-insensitive dynamic pressure measurement using a single fiber Bragg grating (FBG) based on reflection spectrum bandwidth modulation and optical power detection is proposed. A specifically designed double-hole cantilever beam is used to provide a pressure-induced axial strain gradient along the sensing FBG and is also used to modulate the reflection bandwidth of the grating. The bandwidth modulation is immune to spatially uniform temperature effects, and the pressure can be unambiguously determined by measuring the reflected optical power, avoiding the complex wavelength interrogation system. The system acquisition time is up to 85 Hz for dynamic pressure measurement, and the thermal fluctuation is kept less than 1.2% full-scale for a temperature range of -10 degrees C to 80 degrees C.     

Cascaded tilted fiber Bragg grating for enhanced refractive index sensing

We proposed and experimentally demonstrated a cascaded tilted fiber Bragg grating(TFBG) for enhanced refractive index sensing. The TFBG is UV-inscribed in series in ordinary single-mode fiber(SMF) and reduced-diameter SMF with the same tilt angle, and then excites two sets of superposed spectral combs of cladding modes. The cascaded TFBG with total length of 18 mm has a much wider wavelength range over 100 nm and narrower wavelength separation than that of a TFBG only in the SMF, enabling an enlarged range and a higher accuracy of refractive index measurement. The fabricated TFBG with the merits of enhanced sensing capability and temperature self-calibration presents great potentials in the biochemical sensing applications.     

基于滤波法的光纤光栅传感解调方案

FBG传感器对应变和温度的敏感体现在其反射光中心波长的变化上，因此如何测量波长的变化就成为FBG传感器的关键。在光纤光栅的多种解调方法中，因滤波法的测量器件制作简单，测量系统简易、方便直观而被广泛应用。主要介绍了8种基于滤波法的解调方法，对它们各自的成本、检测精度、测量范围、器件制作以及适用的环境进行了详细的比较，分析了它们的优缺点，以便于在不同的检测条件下选用最佳的解调方案。重点介绍了光学小波滤波解调法，探讨了其测量系统的原理，并指出该方法可用于微弱信号的检测与处理。     

光纤布拉格光栅的应变传感实验的研究

针对光纤布拉格光栅的应变特性进行了实验研究,利用计算机采集和处理数据.实验结果表明,Bragg波长随纵向应变的变化呈现出良好的线性,与理论分析结果一致;光栅的涂敷材料不会改变它的线性,但会引起光栅的应变灵敏度变化.     

Erbium-doped fiber ring laser sensor for high temperature measurements based on a regenerated fiber Bragg grating

This article presents an erbium-doped fiber ring laser for high temperature measurement with high accuracy. The proposed laser sensor employs a regenerated fiber Bragg grating (RFBG) as a sensor element. Through thermal treatments, the RFBG with enhanced thermal resistance was obtained. The laser emission optical spectrum presents good performance with a high optical signal-to-noise ratio of 58dB. Experimental results demonstrate a wavelength sensitivity to the temperature is 15.5 pm/ºC with the temperature range from 300ºC to 900ºC, and the correlation coefficient is 0.999. The results prove it is able to provide potential applications in high temperature measurement.     

保偏光纤光栅温度传感性能的实验研究

在经过氢敏化处理的保偏光纤上制作了中心波长在1300 nm窗口的光纤布拉格光栅，并对这种保偏光纤布拉格光栅的温度传感特性进行了实验研究与理论分析。结果表明这种光栅可以用作温度传感器，对温度进行测量。和普通的标准单模光纤布拉格光栅一样，它对温度的响应具有很好的线性关系。本实验结果还可以作为对保偏光纤光栅传感特性进一步深入研究的参考。     

光纤光栅传感技术在工程中的应用

综述了光纤光栅传感器近年来在工程结构健康监测、石油产业、电力行业、岩土工程、航空航天、采矿、爆破、交通及医学等各个领域的应用情况。文章认为,限制光纤光栅传感器产业化和大规模应用的主要因素是缺乏统一的设计理论和制作方法,这使得不同厂家生产的传感器规格存在差异。另外,由于复杂的生产技术和精细的生产过程使传感器生产成本较高,而且能实际应用的光纤光栅传感器的解调产品并不多,且价格很高。根据上述分析,文中对该项技术未来的发展方向提出了展望。     

强度解调型光纤光栅温度传感实验

光纤光栅在工程上应用广泛,但由于存在解调系统复杂、成本高,尤其是需要使用光纤光谱仪等波长解调仪器,使得光纤光栅很难走入本科教学的实验课堂.本文提出了一种基于窄线宽DFB激光器的强度解调方案,极大地简化了光纤光栅传感器的解调系统,完全满足较高分辨率和实时检测的系统要求.合理安排的温度传感实验可以非常直观地展示光纤光栅的线性传感性能,使得工程化的光纤光栅传感技术轻松走进本科教学课堂,具有极高的推广和应用潜力.     

Multiwavelength Brillouin-erbium fiber laser incorporating a fiber Bragg grating filter

In this paper, we demonstrate a multiwavelength Brillouin erbium fiber laser in a Fabry-Perot cavity. The design utilized a bidirectional oscillation provided by a fiber Bragg grating filter and a fiber loop mirror at each end of the laser cavity. A stable operation of 25 Brillouin-Stokes lines was obtained at around a 1559-nm band.     

Parameters of a laser diode with a fiber Bragg grating at different fiber lengths

Theoretical and experimental results are used to demonstrate that an increase in the pump current leads to an increase in the range of continuous variation in the radiation wavelength and power of a laser diode with a fiber Bragg grating with a decrease in the fiber length. An expression for the gain that depends on the carrier density in the laser active area is derived. The watt-ampere and spectral characteristics that are calculated in the two cases are in reasonable agreement.     

基于飞秒激光直写光纤光栅的掺镱光纤激光器

 利用飞秒激光微加工技术,可以在光纤纤芯内直写出布拉格光栅,它与传统的光纤光栅制作方法相比,具有耗时短、无需光敏光纤、周期可任意设定、光栅稳定性高等优点。采用800 nm钛宝石飞秒激光器,在Hi1060光纤内写入一支8 mm长的布拉格光栅,光纤光栅的周期为2.9 μm,这是中心波长为1 042 nm的八阶光纤布拉格光栅。将所得光栅与一段有源的双包层光纤熔接,作为激光输出镜,利用975 nm的LD光纤模块作为泵浦源,采用端泵浦技术构成双包层光纤激光器。双包层光纤采用Nufern公司镱(Yb³⁺)离子掺杂双包层光纤,光纤长度3 m。所得激光器的输出功率为71.1 W,中心波长1 042 nm,带宽约为0.8 nm。     

基于飞秒激光直写光纤光栅的掺镱光纤激光器

利用飞秒激光微加工技术,可以在光纤纤芯内直写出布拉格光栅,它与传统的光纤光栅制作方法相比,具有耗时短、无需光敏光纤、周期可任意设定、光栅稳定性高等优点。采用800 nm钛宝石飞秒激光器,在Hi1060光纤内写入一支8 mm长的布拉格光栅,光纤光栅的周期为2.9 μm,这是中心波长为1 042 nm的八阶光纤布拉格光栅。将所得光栅与一段有源的双包层光纤熔接,作为激光输出镜,利用975 nm的LD光纤模块作为泵浦源,采用端泵浦技术构成双包层光纤激光器。双包层光纤采用Nufern公司镱(Yb3+)离子掺杂双包层光纤,光纤长度3 m。所得激光器的输出功率为71.1 W,中心波长1 042 nm,带宽约为0.8 nm。