High-resolution measurements of molecular absorption line profiles at 10 micrometers

Absorption line profiles of CO₂, C₂H₄ and NH₃ have been measured around a wavelength of 10 μm and under various conditions using a passive heterodyne detection technique with a resolution of 6 × 10^-4 cm^-1.     

A cold thermionically emitting dusty air plasma formed by radiativeheating of graphite particulates

Formation of an atmospheric pressure dusty air plasma is explored experimentally in this paper. The plasma is created by seeding an air flow with graphite particles and irradiating the particulates with a focused CO₂ laser beam. The graphite particles are, thus, heated to thermionically emitting temperatures, and average particle temperatures and average particle number densities are measured. The presence of charges is inferred both from these measured quantities using a simple theoretical transient model, and experimentally by applying a dc bias across the irradiated region. It is found that an electron density of ~6.7 × 10⁵ cm^-3 (6.7 × 10¹¹ m^-3) can be produced at steady state in the presence of O₂. This value can be increased to 3.6 × 10⁷ cm^-3 (3.6 × 10¹³ m ^-1) in the ideal case where an electron attachment to O₂ is suppressed and where a lower work function particulate is used     

Near-infrared absorptions of monomethylhydrazine

The peak absorption coefficients for two near-infrared absorptions of monomethylhydrazine, CH₃-N₂H₃, (MMH) were measured. Absorption bands located at 1.524 μm (6560 cm^-1), 1.557 μm (6423 cm^-1), and 1.583 μm (6316 cm^-1) are assigned to the υ = 2 overtones of the infrared N-H stretching fundamentals at 3317, 3245 and 3177 cm^-1. An absorption band located at 1.04 μm (9620±100 cm^-1) is assigned to the υ = 3 overtone of one of these fundamentals. The peak absorption coefficients (₁₀) at 1.524 μm (6560±20 cm^-1) and 1.04 μm (9620±100 cm^-1) are 31 × 10^-3 and 0.97 × 10^-3 (cm atm)^-1, respectively. Uncertainties in these coefficients were estimated to be less than ±20% due primarily to uncertainties in the partial vapor pressure of MMH.     

宽带腔增强吸收光谱技术应用于痕量气体探测及气溶胶消光系数测量

基于氙灯的非相干宽带腔增强吸收光谱系统, 并将其应用于痕量气体及气溶胶消光系数的测量. 该系统的探测灵敏度通过测量NO₂在520—560 nm波长范围内的吸收得到验证, 最小可探测灵敏度为1.8× 10^-7cm^-1 (1σ, 0.12 s积分时间, 50次平均), 对应的NO₂探测极限～33 nmol/mol. 结合标准气溶胶粒子发生系统, 测量了不同浓度的单分散硫酸铵气溶胶粒子在532 nm波长处的消光系数, 得到粒径为600 nm的硫酸铵气溶胶的消光截面为1.12× 10^-8cm², 与文献报道值1.167× 10^-8cm²相一致, 验证了气溶胶测量的可行性和准确性.     

LaTiO高k栅介质Ge MOS电容电特性及Ti含量优化

采用共反应溅射法将Ti添加到La_2O_3中,制备了LaTiO/Ge金属-氧化物-半导体电容,并就Ti含量对器件电特性的影响进行了仔细研究.由于Ti-基氧化物具有极高的介电常数,LaTiO栅介质能够获得高k值;然而由于界面/近界面缺陷随着Ti含量的升高而增加,添加Ti使界面质量恶化,进而使栅极漏电流增大、器件可靠性降低.因此,为了在器件电特性之间实现协调,对Ti含量进行优化显得尤为重要.就所研究的Ti/La_2O_3比率而言,18.4%的Ti/La_2O_3比率最合适.该比率导致器件呈现出高k值(22.7)、低D_(it)(5.5×10~(11)eV~(-1)·cm~(-2))、可接受的J_g(V_g=1V,J_g=7.1×10~(-3)A·cm~(-2))和良好的器件可靠性.     

基于中红外量子级联激光器和石英增强光声光谱的CO超高灵敏度检测研究

采用石英增强光声光谱(QEPAS)技术对CO痕量气体展开检测研究. 为了实现超高灵敏度探测, 采用输出波长为4.6 μm的新颖中红外高功率分布反馈量子级联激光器为光源, 实现了对CO气体基频吸收带的激发与测量. 在优化了调制深度、气体压强和提高了CO分子的振动-转动弛豫速率后, 获得了1.95 ppbv的优异探测极限. 在分析检测结果的过程中, 讨论了能级寿命对信号强度的影响, 并对QEPAS信号强度的表达式进行了修正.     

基于单个量子级联激光器的大气多组分测量方法

利用单个新型中红外量子级联激光器作为激光光源,结合长程光学吸收池技术开展了大气多组分同时测量方法的研究.通过结合基于自适应性Savitzky-Golay滤波的数据处理算法,有效地提高了系统检测灵敏度和光谱分辨率.研究结果表明,在1 s的时间分辨率和1 atm压力条件下,采用二次微分探测技术可实现CO,N_2O和H_2O测量精度分别为8.20 ppb,7.90 ppb和64.00 ppm(1 ppb=10~(-9),1 ppm=10~(-6));通过提高信号平均时间,在最佳的积分时间(85 s)时,系统可实现的最小检测限分别为1.25 ppb(CO),1.15 ppb(N_2O)和35.77 ppm(H_2O).整个系统具有结构紧凑,成本相对较低,通过选择其他波段的量子级联激光器的激光光源,即可实现对其他分子的实时分析.本系统可广泛应用于大气化学等领域的应用研究.     

流延法制备高锂离子电导Li_(1.4)Al_(0.4)Ti_(1.6)(PO_4)_3固态电解质及其环氧树脂改性

以溶胶凝胶法合成的高纯Li_(1.4)Al_(0.4)Ti_(1.6)(PO_4)_3(LATP)纳米晶体粉末为原料,通过流延法成膜,在950℃下煅烧5 h合成LATP固态电解质片;对其进行环氧树脂改性后,能量色散X射线光谱元素图像表明环氧树脂完全浸入LATP内部,可以有效防止水渗透.研究发现流延法合成的LATP固态电解质在25℃?C时电导率高达8.70×10~(-4)S·cm~(-1)、活化能为0.36 eV、相对密度为89.5%.经过环氧树脂改性后电导率仍高达3.35×10-4S·cm-1、活化能为0.34 e V、相对密度为93.0%.高电导隔水的环氧树脂改性LATP固态电解质可作为锂金属保护薄膜用于新型高比容量电池.     

Temperature dependence of intensities and widths of N2-broadened lines in the 15 μm CO2 band from tunable laser measurements

Intensities and nitrogen-broadened widths of several low-J lines in the Q-branch of the 15 μm band of CO₂ have been determined over the temperature range 200–300 K. Measurements were made with a tunable infra-red diode laser spectrometer having a spectral resolution 10^-4 cm^-1. Measured intensities are uniformly about 7% lower than available calculations which were based on previous measurements of band intensity. Measured line widths are higher than available calculations and generally followed the relation

b_L⁰(T)=b_L⁰(T₀)(T₀|T)ⁿ

with n = 0.74 (standard deviation 0.08).     

基于光强与吸收率非线性同步拟合的吸收光谱测量方法

针对高压环境吸收谱线加宽以及波分复用技术合波透射信号分析测试难题,提出利用非线性拟合方法对激光吸收光谱测量中激光强度与吸收光谱进行耦合求解.建立激光强度非线性变化与多谱线吸收拟合函数关系,解决了特殊环境下无法获取光谱基线的难题,实现了波分复用过程合波后光谱信号的分离与诊断.通过仿真验证该方法的可行性,分析计算了激光器特性和特征谱线位置等因素对拟合结果的影响.搭建实验台实现了1—10 atm变压力环境下6330—6337 cm~(-1)波段CO_2吸收光谱叠加信号的诊断分析,对气液两相脉冲爆轰过程中7185.6 cm~(-1)与7444.35 cm~(-1)波段波分复用光谱信号进行测试与拟合,无需分光设备实现了耦合光路分离和温度计算,研究结果对激光吸收光谱技术在高压环境以及燃烧环境下波分复用技术的发展具有重要意义.     

应用于碳同位素丰度测量的激光频率刻度系统研究

对应用于激光吸收光谱法碳同位素丰度测量中的激光频率实时刻度系统进行研究. 采用不同自由光谱范围的共焦法布里-珀罗干涉仪对测量过程中的激光扫描频率进行实时测量. 分别采用线性内插法和多项式拟合法对激光频率每次扫描过程中的频率非线性进行分析,通过对4976–4980 cm^-1波段CO₂吸收谱的多次测量平均的实验结果与HITRAN-2008数据库相应的吸收峰数据进行比较,得到两种方法的激光频率刻度精度均可达到10^-4 cm^-1,线性内插法的刻度精度要好于多项式拟合法. 验证了激光频率实时刻度系统在碳同位素丰度测量中应用的可行性. 关键词： 激光频率实时刻度 共焦法布里-珀罗干涉仪 同位素丰度测量 激光吸收光谱法     

过渡区p型氢化硅氧薄膜结构和光电特性的研究

采用射频等离子体增强化学气相沉积技术,利用二氧化碳(CO_2)、氢气(H_2)、硅烷(SiH_4)和乙硼烷(B_2H_6)作为气源,制备出一系列p型氢化硅氧薄膜.利用拉曼光谱、傅里叶变换红外光谱和暗电导测试,研究了不同二氧化碳流量对薄膜材料结构和光电特性的影响,获得了从纳米晶相向非晶相转变的过渡区P层.研究表明:随着二氧化碳流量从0增加到1.2 cm~3·min~(-1),拉曼光谱的峰值位置从520 cm~(-1)逐渐移至480 cm~(-1).材料红外光谱表明,随着二氧化碳流量的增加,薄膜中的氧含量逐渐增加,氢键配置逐渐由硅单氢键转换为硅双氢键.P层SiO:H薄膜电导率从3S/cm降为8.3×10~(-6)S/cm.所有p型SiO:H薄膜的光学带隙(Eopt)都在1.82—2.13 eV之间变化.在不加背反射电极的条件下,利用从纳米晶相向非晶相转变的过渡区P层作为电池的窗口层,且在P层和I层之间插入一定厚度的缓冲层,制备出效率为8.27%的非晶硅薄膜电池.     

PHOTO-ACOUSTIC MEASUREMENTS OF WATER VAPOR ABSORPTION COEFFICIENT IN UV SPECTRAL REGION

Data on the absorption coefficient of H₂O in binary mixture with N₂ in UV region of spectra are presented. With the use of the high sensitivity photoacoustic spectrometer, the following values of the absorption coefficient were found: 2.3×10^-9cm^-1·Pa^-1(λ=255 nm), 0.9×10^-9 cm^-1·Pa^-1(λ=271 nm), and 1.6×10^-9cm^-1 ·Pa^-1(λ=289 nm).     

连续波差分吸收激光雷达测量大气CO_2

研制了一套接收硬目标回波的差分吸收激光雷达系统以用于全天候监测大气CO2浓度变化.系统采用10和12 kHz正弦波分别对处在CO2吸收峰内和吸收峰外的波长进行强度调制,利用单频检测技术提取回波信号.提出了一种利用激光扫频推算系统精度的方法,从而弥补了长期以来只能在理论上计算差分吸收激光雷达系统精度的不足,给实际系统自定标问题提供了一种解决方案.该系统采用全光纤结构,结构可靠,便于移动.利用此系统获得了上海市多天CO2浓度变化曲线,在450 m的积分路径长度上,1 s的积分时间取得了优于3.39×10-6的测量精度.     

Improved constants for the 7820 Å and 7883 Å bands of CO2

High-dispersion spectra of Venus are used to obtain line positions and band constants for the (105)_I and (105)_II bands of CO₂. An improved method of analysis is used to obtain very accurate results. Assuming B″ = 0.390218 and D″ = 13.3 × 10^-8 for the ground state, we find for 7820: ω₀ = 12774.727 cm^-1 ±0.002, B' = 0.374540 ±0.000006, D' = 10.9 × 10^-8 ±0.4, for 7883: ω₀ = 12672.274 cm^-1 ±0.004, B' = 0.375657 ±0.000014, D' = 17.2 × 10^-8 ±1.7,

The values for ω₀ and B' are at least an order of magnitude more accurate than those given by Herzberg and Herzberg in 1953, and the D' values are new.     

温稠密钛电导率计算

温稠密物质是惯性约束核聚变、重离子聚变、Z箍缩动作过程中物质发展和存在的重要阶段. 其热力学性质和辐射输运参数在聚变实验和内爆驱动力学模拟过程中有至关重要的作用. 本文通过建立非理想Saha方程, 结合线性混合规则的理论方法模拟了温稠密钛从10^-5-10 g·cm^-3, 10⁴ K到3×10⁴ K区间的粒子组分分布和电导率随温度密度的变化, 其中粒子组分分布由非理想Saha方程求解得到. 线性混合规则模型计算温稠密钛的电导率时考虑了包括电子、原子和离子之间的多种相互作用. 钛的电导率的计算结果与已有的爆炸丝实验数据相符. 通过电导率随温度密度变化趋势判断, 钛在整个温度区间, 密度0.56 g·cm^-3时发生非金属相到金属相相变. 对于简并系数和耦合系数的计算分析, 钛等离子体在整个温度和密度区间逐渐从弱耦合、非简并状态过渡到强耦合部分简并态.     

Time-dependent response of interface states determined by using differential isothermal transient spectroscopy

A method based on the differential analysis of the isothermal transients is proposed to study the dynamical properties of the charging and discharging of interface states, and several possibilities of using this method are shown. The results obtained in SiO₂/Si and Si₃N₄/SiO₂/Si samples are in agreement with the existence of a spatial and energy distribution of interface states within the insulator. From the experimental data, the concentration of traps within the insulator at 35 Å is estimated to be 5×10⁹ cm^-2 eV^-1, with a tunneling cross section 10^-19 cm², at E_c-E ≈ 0.2 eV.     

用于α和μ常数变化测量的碘离子光谱研究

分子离子I_2~+的禁戒跃迁光谱有可能用于测量α和μ常数的变化,并且具有增强的灵敏度.通过分析I_2~+在11860—13100 cm~(-1)范围内的转动光谱,拟合了A~2Π_(3/2)-X~2Π_(3/2)系统31个振转带的5759根吸收谱线,得到5个属于X~2Π_(3/2)态和9个属于A~2Π_(3/2)态的振动能级准确的转动光谱常数.在量子噪声极限和1 Hz跃迁线宽的条件下,计算得到X~2Π_(3/2)和X~2Π_(1/2)之间的禁戒跃迁对α和μ常数变化测量的灵敏度为δ_(α/α)≈2.37×10~(-19)a~(-1)和δ_(μ/μ)≈1.18×10~(-18)a~(-1).     

Frequency measurement of RuO4 transitions in the υ3 vibrational band

The frequencies of the most intense RuO₄ transitions in coincidence with the emission lines of CO₂ and N₂O lasers have been measured with respect to the CO₂ lines with an uncertainty of less than 3× 10^-9. Difference and absolute frequency values are here reported.     

光纤倏逝波型石英增强光声光谱技术

采用块状光学准直聚焦透镜组的传统石英增强光声光谱(QEPAS)技术存在体积难以缩减,结构稳定性不佳,无法适应空间狭小、振动复杂的特殊环境等缺点.基于此,将光纤倏逝波技术与QEPAS技术相结合,提出了一种新型微纳结构光纤QEPAS痕量气体检测技术.实验中,为了提高QEPAS系统信号幅值,优化了石英音叉与激光束的空间位置、激光波长调制深度,同时对比了两种不同共振频率的石英音叉,最终采用共振频率较低的30.720 kHz石英音叉作为声波探测元件,获得的检测极限为6.25×10~(-4)(体积分数),归一化噪声等效吸收系数为4.18×10~(-7)cm~(-1).W·Hz~(-1/2).