单轴应变条件下Fe从α到ε结构相变机制的第一性原理计算

采用基于密度泛函理论的平面波赝势方法,研究了沿［001］方向单轴应变条件下Fe从体心立方结构(bcc,α相)到六角密排结构(hcp,ε相)相变的临界压力、相变路径、相变势垒以及相变过程中原子磁性的变化.结果发现:单轴应变条件下Fe从α到ε结构的相变路径与以前理论计算模拟给出的静水压力条件下的相变路径明显不同;原子磁矩沿着相变路径突然降低,同时伴随着能量和体积的突然变化,是典型的一阶磁性相转变,表明原子磁性的丧失导致了bcc结构不稳定而向hcp结构转变.对单轴应变下吉布斯自由能的计算表明,相变势垒随着单轴应 关键词： 相变 单轴应变 第一性原理 铁     

Twinning to slip transition in ultrathin BCC Fe nanowires

We report twinning to slip transition with decreasing size and increasing temperature in ultrathin <100> BCC Fe nanowires. Molecular dynamics simulations have been performed on different nanowire size in the range 0.404–3.634 nm at temperatures ranging from 10 to 900 K. The results indicate that slip mode dominates at low sizes and high temperatures, while deformation twinning is promoted at high sizes and low temperatures. The temperature, at which the nanowires show twinning to slip transition, increases with increasing size. The different modes of deformation are also reflected appropriately in the respective stress–strain behaviour of the nanowires.     

温度和应变速率耦合作用下纳米晶Ni压缩行为研究

本文利用低温力学测试系统研究了电化学沉积纳米晶Ni在不同温度和宽应变速率条件下的压缩行为. 借助应变速率敏感指数、激活体积、扫描电子显微镜及高分辨透射电子显微镜方法, 对纳米晶Ni的压缩塑性变形机理进行了表征. 研究表明, 在较低温度条件下, 纳米晶Ni的塑性变形主要是由晶界位错协调变形主导, 晶界本征位错引出后无阻碍的在晶粒内无位错区运动, 直至在相对晶界发生类似切割林位错行为. 并且, 在协调塑性变形时引出位错的残留位错能够增加应变相容性和减小应力集中; 在室温条件下, 纳米晶Ni的塑性变形机理主要是晶界-位错协调变形与晶粒滑移/旋转共同主导. 利用晶界位错协调变形机理和残留位错运动与温度及缺陷的相关性揭示了纳米晶Ni在不同温度、不同应变速率条件下力学压缩性能差异的内在原因.     

Molecular dynamics study of coupled layer thickness and strain rate effect on tensile behaviors of Ti/Ni multilayered nanowires

Novel properties and applications of multilayered nanowires(MNWs) urge researchers to understand their mechanical behaviors comprehensively.Using the molecular dynamic simulation,tensile behaviors of Ti/Ni MNWs are investigated under a series of layer thickness values(1.31,2.34,and 7.17 nm) and strain rates(1.0 × 10~8 s~(-1) ≤ε≤5.0 × 10~(10) s~(-1)).The results demonstrate that deformation mechanisms of isopachous Ti/Ni MNWs are determined by the layer thickness and strain rate.Four distinct strain rate regions in the tensile process can be discovered,which are small,intermediate,critical,and large strain rate regions.As the strain rate increases,the initial plastic behaviors transform from interface shear(the shortest sample) and grain reorientation(the longest sample) in small strain rate region to amorphization of crystalline structures(all samples) in large strain rate region.Microstructure evolutions reveal that the disparate tensile behaviors are ascribed to the atomic fractions of different structures in small strain rate region,and only related to collapse of crystalline atoms in high strain rate region.A layer thickness-strain rate-dependent mechanism diagram is given to illustrate the couple effect on the plastic deformation mechanisms of the isopachous nanowires.The results also indicate that the modulation ratio significantly affects the tensile properties of unequal Ti/Ni MNWs,but barely affect the plastic deformation mechanisms of the materials.The observations from this work will promote theoretical researches and practical applications of Ti/Ni MNWs.     

不同取向下单晶铁纳米线拉伸行为的模拟研究

本文利用分子动力学模拟的方法研究了不同取向、尺寸和温度因素对单晶体心立方铁纳米线的拉伸变形行为的影响.铁纳米线轴向初始取向分别为<001>、<110>、<111>、<102>、<112>,模拟了不同温度(10～700 K)和不同尺寸范围(1.5～5 nm)下的变形机制.研究结果表明取向、尺寸和温度会显著影响单晶体心立方铁纳米线的拉伸变形行为.分子动力学模拟结果表明,直径为2 nm的<001>铁纳米线在300 K的拉伸载荷下,主要通过孪晶的模式发生变形,最后拉伸取向转变为<110>.而在700 K下,<001>铁纳米线的拉伸变形模式由滑移主导.不同初始取向在不同温度和尺寸下其变形机制截然不同,这导致了铁纳米线不同的力学性能.本文系统性地研究了在不同取向下的铁纳米线变形机制随尺寸和温度变化发生的转变.     

Shear-Banding Evolution Dynamics during High Temperature Compression of Martensitic Ti-6Al-4V Alloy

The isothermal compression dynamics of ternary Ti-6 Al-4 V alloy with initial martensitic structures were investigated in the high temperature range 1083-1173 K and moderate strain rate regime 0.01-10 s^-1.Shear banding was found to still dominate the deformation mechanism of this process,despite its nonadiabatic feature.The constitutive equation was derived with the aid of Zener-Hollomon parameter,which predicted the apparent activation energy as 534.39 kJ/mol.A combination of higher ...     

Face-centred cubic to body-centred cubic phase transformation under [1 0 0] tensile loading

Molecular dynamics simulation was used to verify a speculation of the existence of a certain face-centred cubic (FCC) to body-centred cubic (BCC) phase transformation pathway. Four FCC metals, Ni, Cu, Au and Ag, were stretched along the [1?0?0] direction at various strain rates and temperatures. Under high strain rate and low temperature, and beyond the elastic limit, the bifurcation of the FCC phase occurred with sudden contraction along one lateral direction and expansion along the other lateral direction. When the lattice constant along the expansion direction converged with that of the stretched direction, the FCC phase transformed into an unstressed BCC phase. By reducing the strain rate or increasing the temperature, dislocation or ‘momentum-induced melting’ mechanisms began to control the plastic deformation of the FCC metals, respectively.     

Effect of the temperature and way of preliminary torsion in the austenitic state on the shape memory effect in TiNi alloy

The effect of temperature and direction of preliminary torsion in the austenitic state on the degree of strain recovery upon heating of a TiNi alloy has been investigated. It is shown that an increase in the preliminary deformation temperature from 500 to 700 K leads to an increase in the degree of shape recovery upon heating of the material studied. In particular, a 20% strain at a temperature of 500 K decreases the recovery coefficient by 20%, whereas the same preliminary strain at 700 K deteriorates the shape recovery by only 4%. It is established that, applying preliminary torsion in the austenitic and martensitic states in opposite directions, one can obtain an increase in the shape memory strain with an increase in the preliminary plastic strain. Thus, at some plastic strains (λ _pl > 10%), the strain recovered upon heating may even exceed the strain set in the martensitic state.     

Elasto-plastic phase-field simulation of martensitic transformation in lath martensite steels

Phase-field simulation of lath martensite formation in Fe–0.1C mass% steel was carried out based on the two types of slip deformation (TTSD) model, which is recently developed as a result of analytical solution for the martensitic transformation being composed of Bain deformation and plastic deformation but without lattice rotation matrix. The simulation results reveal that the plastic deformation along the two types of slip system is complementary. The simulation result of the relationship between the two types of slip deformation is consistent with the analytical result calculated by TTSD model, indicating the validity of TTSD model for explaining the formation of lath martensite.     

内应力对Mn2NiGa铁磁形状记忆合金的结构、相变和磁性能的影响

通过施加压应力的方法,在铁磁形状记忆合金Mn₂NiGa中引入残留内应力,研究了内应力对 Mn₂NiGa材料的结构、相变和磁性能的影响.研究发现,加压过程使材料发生了塑性形变,在材料内部引入了大量的位错缺陷.卸载后保留的位错缺陷在材料中造成了残留的内应力,导致了马氏体相变温度大幅度提高, 使原本室温下的母相转变成了马氏体相.测量到导致样品转变成马氏体的阈值压应力为1.0 GPa.加压形成的马氏体中的残留内应力将矫顽力从低于50 Oe提高到350 Oe.残留内应力在730 K的热处理中由于位错缺陷的消失而得以消除,样品实现了马氏体逆相变.如此高的逆相变温度使得 Mn₂NiGa马氏体的居里温度测量成为可能,获得了530K的数值.     

Face-centered-cubic to body-centered-cubic phase transformation of Cu nanoplate under [100] tensile loading

ABSTRACT

Molecular dynamics simulation was used to stretch Cu nanoplates along its [100] direction at various strain rates and temperatures. Under high strain rate and beyond the elastic limit, the Cu nanoplates underwent an unusual deformation mechanism with expansion along free surface lateral direction and contraction along the other lateral direction, which leaded to the face-centred-cubic phase transforming into unstressed body-centred-cubic phase. Under low strain rate, the deformation of the nanoplate went back to well-known dislocation mechanism. The face-centred-cubic to body-centred-cubic phase transformation mechanism was further discussed in terms of elastic stability theory and free surface stress effect.     

Ni53.2Mn22.6Ga24.2单晶的两步热弹性马氏体相变及其应力应变特性

对具有两步完全热弹性的Ni_53.2Mn_22.6Ga_24.2单晶的物性采用多种测量手段进行了表征,特别研究了不同温度下的应力-应变特性.研究表明,热诱发的中间马氏体相变应变远大于马氏体相变应变.在较低的形变温度下,沿单晶母相［001］方向的压应力诱发的是两步马氏体相变,材料表现出赝弹性;在较高的形变温度下,只能观察到一步马氏体相变,材料展现出完全超弹性特性.此外,利用热力学理论分别计算了诱发马氏体相变和中间马氏体相变的临界应力与形变温度的关系,与实验测量得到的结果相符. 关键词： 马氏体相变 形状记忆效应 应变 超弹性     

Homogeneous Cu–Fe supersaturated solid solutions prepared by severe plastic deformation

A Cu–Fe nanocomposite containing 50 nm thick iron filaments dispersed in a copper matrix was processed by torsion under high pressure at various strain rates and temperatures. The resulting nanostructures were characterized by transmission electron microscopy, atom probe tomography (APT) and Mössbauer spectrometry. It is shown that α-Fe filaments are dissolved during severe plastic deformation leading to the formation of a homogeneous supersaturated solid solution of about 12 at% Fe in fcc Cu. The dissolution rate is proportional to the total plastic strain but is not very sensitive to strain rate. Similar results were found for samples processed at liquid nitrogen temperature. APT data revealed asymmetric composition gradients resulting from deformation-induced intermixing. On the basis of these experimental data, the formation of the supersaturated solid solutions is discussed.     

Effect of upsetting deformation temperature on the formation of the fine-grained cast alloy structure of the Ni–Mn–Ga system

The plastic behavior during deformation by upsetting and its effect on the microstructure in the polycrystalline Ni_2.19Fe_0.04Mn_0.77Ga alloy are studied. The temperatures of martensitic and magnetic phase transformations were determined by the method for analyzing the temperature dependence of the specific magnetization as M _F = 320 K, A _S = 360 K, and T _C = 380 K. Using differential scanning calorimetry, it is shown that the phase transition from the ordered phase L2₁ to the disordered phase B2 is observed in the alloy during sample heating in the temperature range of 930–1070 K. The melting temperature is 1426 K. An analysis of the load curves constructed for sample deposition at temperatures of 773, 873, and 973 K shows that the behavior of the stress–strain curve at a temperature of 773 K is inherent to cold deformation. The behavior of the dependences for 873 and 973 K is typical of hot deformation. After deforming the alloy, its microstructure is studied using backscattered scanning electron microscopy. Plastic deformation of the alloy at study temperatures results in grain structure fragmentation in the localized deformation region. At all temperatures, a recrystallized grain structure is observed. It is found that the structure is heterogeneously recrystallized after upsetting at 973 K due to the process intensity at such a high temperature. The alloy microstructure after plastic deformation at a temperature of 873 K is most homogeneous in terms of the average grain size.     

Prediction of flow stress and textures of AZ31 magnesium alloy at elevated temperature

The viscoplastic behaviour of magnesium alloys at high temperatures leads to highly temperature-dependent mechanical properties. While at high strain rates a notable strain hardening response is observed, at low strain rates the material shows a smooth plastic response with negligible amount of hardening. This complicated behaviour is due to different deformation mechanisms that are active at different strain rate regimes, resulting in different strain rate sensitivity parameters. In this study we show, by utilizing both numerical simulations and experiments, that this behaviour can be predicted by a model that combines two deformation mechanisms, grain boundary sliding mechanism and dislocation glide mechanism. We discuss the importance of each deformation mechanism at different strain rate regimes based on the findings of modelling and experimental results for AZ3 magnesium alloy. By developing a model that includes the above-mentioned two deformation mechanism, the prediction of flow properties is expanded to a wide range of strain rate regimes compared to previous study. The obtained numerical findings for the stress–strain behaviour as well as texture evolution show good agreement with the experimental results.     

非静水压条件下铁从α到ε结构相变的第一性原理计算

采用基于密度泛函理论的平面波赝势方法,研究了三轴加载的非静水压力和静水压力对铁从体心立方结构（bcc,α相）到六角密排结构（hcp,ε相）相变压力和磁性的影响,结果发现：在0—18 GPa压力范围内,相对静水压力条件,随着压力的升高,bcc结构的原子磁矩在非静水压力下降低得更快;在非静水压力下,相变更容易发生,相变压力随着非静水压力程度的增加而降低;并且对非静水压力对相变压力影响的物理机理进行了讨论. 关键词： 相变 非静水压力 第一性原理 铁     

Acoustoplastic effect and the stress superimposition mechanism

The mechanism of the acoustoplastic effect is discussed which arises when an oscillatory stress of an acoustic frequency is superimposed during quasi-static deformation of a crystal. The kinetics of the acoustoplastic effect and its dependence on the amount of plastic deformation, amplitude of acoustic-frequency stresses, temperature, and strain rate are investigated in terms of the stress superimposition mechanism by a computer simulation method.     

纳米单晶与多晶铜薄膜力学行为的数值模拟研究

通过对不同温度下单晶薄膜的拉伸性能的分子动力学模拟，从微观角度揭示了温度效应对材料性能的影响. 结果表明温度效应对材料的变形机理影响很大.0K温度下由于缺乏热激活软化的影响, 粒子运动所受到的阻碍较大, 薄膜的强度较高, 塑性变形主要来自于粒子的短程滑移.温度升高，粒子的热运动加剧，屈服强度降低, 塑性变形将主要来自于大范围的位错长程扩展.多晶薄膜的模拟结果表明, 虽然其晶粒形状较为特殊, 但是它仍然遵循反Hall-Petch关系.在模拟过程中，侧向应力最大值比拉伸方向应力的最大值滞后出现.位错只会从晶界产生并向晶粒内部传播，晶粒间界滑移是多晶薄膜塑性变形的主要来源. 关键词： 纳米薄膜 变形机理 温度效应 分子动力学     

On the conditions of strain localization and microstructure fragmentation under high-rate loading

The paper reports on research in the deformation and fragmentation mechanisms of coarse- and fine-grained materials under high-rate loading. The study was performed by an experimental procedure based on collapse of thick-walled hollow cylinders and by molecular dynamics simulation. The key issue was to study the formation of plastic strain localization bands. It is found that the pattern of plastic deformation is governed by loading conditions and characteristic grain sizes. For a coarse-grained material, the governing mechanism is dislocation deformation resulting in localization bands. For a fine-grained material, the governing mechanism is grain boundary sliding with attendant fragmentation of the material. A dependence of the strain rate and degree on the critical grain size was disclosed. The computer simulation revealed mechanisms of grain boundary sliding on the scales studied.     

单晶铜纳米线屈服机理的原子模拟研究

采用分子静力学方法模拟了〈100〉单晶铜纳米线的拉伸变形过程,研究了纳米线屈服的机理. 结果表明：1） 纳米线初始屈服通过部分位错随机激活的{111}〈112〉孪生实现,后继屈服通过{111}〈112〉部分位错滑移实现;2） 纳米线变形初期不同滑移面上的部分位错在两面交线处相遇形成压杆位错,变形后期部分位错在刚性边界处塞积,两者都阻碍位错滑移,引起一定的强化作用. 关键词： 纳米线 屈服 位错 分子静力学