双电子传输层对有机发光二极管效率及其衰减的改善

采用Bphen和BCP制成双电子传输层(Doubleelectrontransportlayers, DETLs)的有机发光二极管器件, 与Bphen单独作ETL的器件相比, DETLs器件具有较小的空穴漏电流, 效率提升10%。与BCP独自作ETL的器件相比, 更多的电子注入使DETLs器件的效率在50~600mA/cm²的电流范围内没有衰减。BCP作ETL的器件的效率从50mA/cm²时的2.5cd/A衰减至300mA/cm²的2.1cd/A, 衰减了16%。Cs₂CO₃:BCP独自作ETL的器件效率在50~300mA/cm²的电流范围内衰减了30%, 而Bphen/Cs₂CO₃:BCP作DETLs的器件效率在50~600mA/cm²的电流范围内衰减幅度为0, 原因是Bphen阻挡了Cs原子扩散至发光层。     

阴极修饰层对 SubPc/C60 倒置型有机太阳能电池性能的影响

采用Cs₂CO₃, 石墨烯(graphene):Cs₂CO₃混合材料和 ZnO 纳米颗粒作为阴极修饰材料, 研究了不同阴极界面修饰层对基于SubPc/C₆₀的倒置结构的有机太阳能电池性能的影响. 结果表明: 引入适当厚度的阴极修饰层, 可以提高器件的性能和稳定性; 尤其是基于Cs₂CO₃以及graphene:Cs₂CO₃混合阴极修饰层的光伏器件, 能量转换效率(PCE)提高了2倍; 同时, 采用ZnO纳米颗粒作为阴极修饰层的器件, 开路电压(V_OC)达到0.89 V, 并且器件的PCE 提高了4倍多. 此外, 不同电极修饰材料和倒置结构的引入可以有效防止器件串连电阻的升高, 从而提高器件的稳定性. 关键词： 倒置型 阴极修饰层 有机太阳能电池 稳定性     

使用不同阴极缓冲层提升性能的反型有机太阳能电池

使用含Al_q3、Bphen、BCP、HATNA和Cs₂CO₃作为阴极缓冲层,制备了基于SubPc和C₆₀的反型平面异质结有机太阳能电池. 比较了有机阴极缓冲层的最低未占有分子轨道和电子迁移率对有机太阳能电池性能的影响. 结果显示,Al_q3、Bphen和HATNA能够大幅度提升器件的性能. 使用退火过后的HATNA作为阴极缓冲层获得了最高的效率,比没有阴极缓冲层的器件提升了7倍. 另外,使用空间电荷限制电流理论进行仿真的结果表明,通过加入HATNA作阴极缓冲层,反型有机太阳能电池结构中处于有机/电极界面处的肖特基势垒降低了27%.     

Hybrid polymer/inorganic nanoparticle blended ternary solar cells

Hybrid polymer/inorganic nanoparticle blended ternary solar cells are reported. These solar cells have an active layer consisting of PbS colloidal quantum dots (CQDs), poly (3‐hexylthiophene) (P3HT), and [6,6]‐phenyl‐C61‐butyric acid methyl ester (PCBM). Power conversion efficiency (PCE) was improved by incorporating PbS CQDs in the active layer of P3HT:PCBM‐based organic solar cells. As the concentration of PbS CQDs in the hybrid solar cells was increased, PCE was also increased. This improvement resulted from improved charge transfer and also extended light absorption into the near‐infrared. The PCE of the hybrid solar cells was 47% higher than that for reference organic solar cells on average under air mass 1.5 global illumination. (© 2013 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

掺杂石墨烯量子点对P3HT:PCBM太阳能电池性能的影响

为研究掺杂石墨烯量子点(GQDs)对聚合物电池的影响,采用溶剂热法制备了GQDs,掺杂到聚3-己基噻吩和富勒烯衍生物(P3HT∶PCBM)中作光敏层制备了聚合物太阳能电池。掺杂不同浓度的GQDs后,聚合物电池的开路电压和填充因子都比未掺杂器件高。GQDs掺杂质量分数为0.15%时,形成的掺杂薄膜平整、均匀,填充因子提高了17.42%。GQDs经还原后,随还原时间的延长,填充因子FF增大。到45 min时,电池的FF基本稳定,从31.57%提高至40.80%,提高了29.24%。退火后,获得了最佳的掺杂GQDs的聚合物太阳能电池,开路电压Voc为0.54 V,填充因子FF为55.56%,光电转换效率为0.75%。     

Fe3O4纳米粒子对P3HT:PCBM电池的影响

为了提高太阳能电池的性能,研究磁性纳米粒子在外加磁场的作用下对聚合物太阳能电池有源层P3HT:PCBM成膜及太阳能电池性能的影响。本文采用热分解法制备了磁性Fe₃O₄纳米粒子,将不同质量分数的Fe₃O₄纳米粒子掺入到P3HT:PCBM溶液中,旋涂后在外加磁场的作用下自组成膜。通过TEM、XRD对制备的Fe₃O₄纳米粒子进行表征,并利用偏光显微镜、原子力显微镜对成膜质量进行探究。结果表明,采用热分解法制备的Fe₃O₄纳米粒子直径在10 nm左右,在外加磁场作用下,Fe₃O₄纳米粒子对成膜有一定的调控作用。当Fe₃O₄纳米粒子掺杂质量分数为1%时,太阳能电池器件的开路电压增加3.77%,短路电流增加24.93%,光电转换效率提高7.82%。     

荧光染料掺杂的高效率、高亮度白色有机电致发光器件

制备了结构为 ITO/NPB（30 nm）/Rubrene（0.2 nm）/CBP：Bczvbi（8 nm,x%）/Bphen（30 nm）/Cs₂CO₃：Ag₂O（2 nm,20%）/Al（100 nm）的器件。研究了Bczvbi掺杂浓度（x=5,10,15）对白光器件性能的影响。综合利用发光层中主客体之间的能量转移和空穴阻挡层的空穴阻挡特性,得到了高效率、高亮度的白色有机电致发光器件。当Bczvbi的掺杂质量分数为10%时,器件的效率和亮度都为最大。驱动电压为7 V时,最大电流效率为4.61 cd/A;驱动电压为9 V时,最大亮度为21 240 cd/m²。当驱动电压从4 V增加到9 V时,色坐标从（0.36,0.38）变化为（0.27,0.29）,均处于白光区域。     

NiO_x作为空穴传输层对有机太阳能电池光吸收的影响

基于多层膜系模型的传输矩阵方法、麦克斯韦方程和光子吸收方程,研究了NiOx作为替代3,4-乙撑二氧噻吩:聚苯乙烯磺酸盐(PEDOT:PSS)的空穴传输材料对聚3-己噻吩(P3HT)和富勒烯衍生物([6,6]-phenyl-C61-butyric acid methyl ester,PC61BM)共混体异质结有机太阳能电池器件内部光电场分布和光吸收特性的影响.分别制备了以NiOx和PEDOT:PSS为空穴传输层,P3HT:PCBM为活性层的有机太阳能电池,并通过数值模拟的方法比较了NiOx和PEDOT:PSS两种空穴传输材料对器件光伏特性的影响.结果表明:10 nm的NiOx空穴传输层器件比40 nm的PEDOT:PSS器件获得了更大的短路电流和填充因子,并具有更高的能量转化效率.     

利用阴极修饰层提高有机光伏电池的性能及稳定性

分别制备了以苯甲酸锂、碳酸铯和聚氧化乙烯为阴极修饰层的基于P3HT∶PCBM体系的本体异质结有机光伏电池。比较了3种阴极修饰层对器件性能及稳定性的影响。结果表明:选择合适的阴极修饰层材料是提高光电转换效率、延长电池使用寿命的可行性途径之一。纯无机阴极修饰层不能有效地阻挡氧气和水进入活性层,对于减缓器件的性能衰退效果不如有机阴极修饰层材料。有机聚合物材料可以减小漏电流的产生,开路电压和填充因子都得到很大提高,有利于提高器件的性能及稳定性。合成可溶液加工的具有极性基团的共轭聚合物材料是未来阴极修饰层的发展方向。     

刮涂法制备聚合物薄膜太阳能电池

系统地研究了采用刮涂法制备聚合物薄膜太阳能电池时刮涂速度和基底温度对活性层厚度以及形貌的影响。当刮涂速度增加或者基底温度降低时,由于溶液粘度和表面张力的变化导致活性层厚度增加。与旋涂方法相比,刮涂方法制备的活性层薄膜具有更小的粗糙度和精细的相分离结构,从而减少了光伏电池的漏电流并提高了填充因子。利用刮涂方法制备的聚合物太阳能电池能量转换效率达到了4.2%。     

高效钙钛矿-有机本体异质结杂化串联太阳能电池

制备了一种有机铅卤钙钛矿-有机本体异质结杂化串联太阳能电池。采用紫外可见吸收光谱、原子力显微镜对薄膜形貌进行了表征。结果表明:有机本体异质结层可以有效改善钙钛矿的表面形貌, 增强了可见光的吸收。优化后的串联结构电池的短路电流可达19.14mA/cm², 开路电压为0.76V, 光电转换效率达到了6.54%。钙钛矿电池和有机本体异质结电池串联结构可以同时提高短路电流及填充因子, 二者具有较好的相容性和协同作用。     

纳米银增强聚合物太阳能电池光吸收的研究

基于共轭聚合物给体材料P3HT和富勒烯衍生物受体材料PCBM共混的体异质结结构 的聚合物太阳能电池因其空穴载流子迁移率低而限制了P3HT:PCBM功能层厚度, 从而影响了器件对入射光的吸收. 在聚合物功能层内引入金属纳米颗粒可以利用金属表面等离子体效应增强器件内电场并改善器件的光吸收. 本文基于时域有限差分法(finite difference time domain, FDTD)方法模拟得到了聚合物功能层内包含了直径为50 nm纳米银球并且球间距为50 nm的聚合物太阳能 电池器件在波长分别为400 nm和500 nm照射时的二维光电场分布以及入射角分别为15°, 45°, 60°时包覆纳米银聚合物功能层横截面内的光电场强度分布; 计算得到了银纳米颗粒尺寸分别为10 nm, 20 nm和50 nm时以及分布在空穴传输层PEDOT:PSS的纳米银器件的光吸收; 并计算了斜入射时包覆纳米银的聚合物功能层光吸收. 理论分析表明: 聚合物功能层加入纳米银球后, 因为纳米银球的表面等离子体效应使入射光在功能层内散射增强而使器件内的光电场重新分布; 直径较大的纳米银颗粒能产生大角度的光散射, 更有利于聚合物功能层对光的吸收. 这里, 基于有机银盐还原法制备了纳米银颗粒并制备了银等离子体增强的聚合物太阳能电池, 其结构为: glass/ITO (～100 nm)/PEDOT:PSS (40 nm)/P3HT:PCBM (～100 nm)(nano-Ag)/LiF (1 nm)/Al (120 nm). 该器件与平板器件的性能对比实验证实: 通过在聚合物功能层内上引入纳米银颗粒可以有 效增加器件光吸收并改善器件电学性能, 器件外量子效率在520 nm处最大增加了17.9%. 关键词： 纳米银 表面等离子体共振 时域有限差分 聚合物太阳能电池     

Fe3O4 nanoparticle loaded paclitaxel induce multiple myeloma apoptosis by cell cycle arrest and increase cleavage of caspases in vitro

We experimentally and theoretically characterize back-scattering and extinction of Ag nanoparticle (AgNP) arrays on both Si wafer substrates and optically-thick Ag substrates with and without organic poly(3-hexylthiophene):[6,6]-phenyl C61-butyric acid methyl ester (P3HT:PCBM) bulk-heterojunction thin film coatings. A strong red-shift in back-scattered light wavelength occurs from AgNP arrays on Si as a function of increasing mean nanoparticle diameter (ranging from 30 to 90 nm). Back-scattering from the AgNP array is notably quenched in the wavelength range of strong P3HT absorption when the organic layer is applied. However, back-scattering is enhanced to a degree relative to the uncoated AgNP array on Si at wavelengths greater than the absorption band edge of P3HT. For comparison, the optical properties of AgNPs on an optically-thick Ag substrate are reported with and without P3HT:PCBM thin film coatings. On the reflective Ag substrates, a significant enhancement (by a factor of 7.5) and red-shift of back-scattered light occurred upon coating of the AgNPs with the P3HT:PCBM layer. Additionally, red-edge extinction was enhanced in the P3HT:PCBM layer with the presence of the AgNPs compared to the planar case. Theoretical electromagnetic simulations were carried out to help validate and explain the scattering and extinction changes observed in experiment. Both increasing nanoparticle size and an increasing degree of contact with the Si substrate (i.e., effective index of the nanoparticle environment) are shown to play a role in increasing back- and forward-scattering intensity and wavelength, and in increasing absorption enhancements in both the organic and Si layers. AgNPs placed at the P3HT:PCBM/Si interface give rise to absorption increases in P3HT of up to 18 %, and only enhance Si absorption at wavelengths longer than the absorption band edge of P3HT (by almost 90 % in the 660–1,200 nm wavelength range). These results provide insight into how metal nanoparticles placed near an organic/inorganic interface can be employed for light management in tandem or hybrid organic/inorganic thin-film semiconductor configurations for solar energy harvesting applications or light detection applications.     

三元P3HT:PTB7-Th:PCBM聚合物太阳能电池性能的研究

将窄带隙聚合物PTB7-Th作为第三种物质掺入到P3HT:PCBM中制备了双给体结构的三元聚合物太阳能电池, 并且通过改变PTB7-Th的浓度来研究PTB7-Th对器件性能的影响. 研究发现, 掺入PTB7-Th后, 聚合物太阳能电池的短路电流和填充因子同时获得了提高, 使器件的光电转换效率得到了改善. 进一步分析表明, PTB7-Th的加入能够拓宽活性层的吸收光谱, 增加活性层吸收的光子数目, 有利于短路电流的提升. PTB7-Th与P3HT之间以电荷转移的形式相互作用, 这种作用方式有利于激子的解离, 从而使器件的填充因子得到了提高.     

Performance improvement of MEH-PPV:PCBM solar cells using bathocuproine and bathophenanthroline as the buffer layers

In this work, bathocuproine (BCP) and bathophenanthroline (Bphen), commonly used in small-molecule organic solar cells (OSCs), are adopted as the buffer layers to improve the performance of the polymer solar cells (PSCs) based on poly(2-methoxy-5-(2-ethylhexyloxy)-1,4-phenylenevinylene) (MEH-PPV): [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) bulk heterojunction. By inserting BCP or Bphen between the active layer and the top cathode, all the performance parameters are dramatically improved. The power conversion efficiency is increased by about 70% and 120% with 5-nm BCP and 12-nm Bphen layers, respectively, when compared with that of the devices without any buffer layer. The performance enhancement is attributed to BCP or Bphen (i) increasing the optical field, and hence the absorption in the active layer, (ii) effectively blocking the excitons generated in MEH-PPV from quenching at organic/aluminum (Al) interface due to the large band-gap of BCP or Bphen, which results in a significant reduction in series resistance (Rs), and (iii) preventing damage to the active layer during the metal deposition. Compared with the traditional device using LiF as the buffer layer, the BCP-based devices show a comparable efficiency, while the Bphen-based devices show a much larger efficiency. This is due to the higher electron mobility in Bphen than that in BCP, which facilitates the electron transport and extraction through the buffer layer to the cathode.     

基底温度对喷涂技术制备大面积有机太阳能电池性能的影响

以聚3-己基噻吩（P3HT）和富勒烯衍生物（PCBM）体系的有机太阳能电池器件为基础,采用喷涂法制备了有机太阳能电池的空穴传输层和有机功能层,研究了基底温度对薄膜的形貌和器件性能的影响,并采用喷涂技术制备了一面积为11.2 cm²的大面积有机太阳能电池器件。研究发现,随着基底温度的升高,薄膜的粗糙度下降,吸收率提高,当基底温度为130 ℃时器件的性能最优,面积为25 mm²的器件的能量转换效率为2.09%。将多个独立的小面积电池进行串联和并联,制备了有效面积为11.2 cm²的大面积有机太阳能电池组件,其能量转换效率为1.83%,在面积增大44.8倍的情况下,效率仅损失不到13%。     

不同环境压强下溶剂退火对聚合物太阳能电池性能的影响

通过改变溶剂退火时的环境压强控制溶剂的蒸发速率,在不同压强下进行加压溶剂退火制备了基于聚-3己基噻吩:富勒烯衍生物(P3HT:PCBM)的体异质结聚合物太阳能电池。X射线衍射(XRD)、紫外-可见吸收光谱(UV-Vis)以及原子力显微镜(AFM)的测试结果表明,增大溶剂退火的环境气压改善了薄膜的结晶度,增强了有源层的光吸收,提高了P3HT和PCBM的相分离程度,更有利于激子的解离和载流子传输。与在常压下溶剂退火相比,在2.0 MPa压强下对有源层进行溶剂退火的器件的光电转换效率提高了29%,达到了3.69%。     

基于聚多巴胺/氧化锌复合阴极缓冲层的倒置聚合物太阳能电池的研究

利用多巴胺氧化自聚合形成聚多巴胺(PDA)与ZnO结合形成PDA/ZnO复合阴极缓冲层,制备了以P3HT:PC_(61)BM为活性层的倒置结构聚合物太阳能电池,通过改变PDA的自聚合时间来分析复合阴极缓冲层对器件性能的影响.实验发现,随着PDA的自聚合时间的增加,聚合物太阳能电池的光电转换效率先增大后减小,当自聚合时间为10 min时,相应器件光伏性能达到最优值,其开路电压V_(OC)为0.66 V,短路电流密度J_(SC)为9.70 mA/cm~2,填充因子FF为68.06%,光电转换效率PCE为4.35%.器件性能改善的原因是由于PDA/ZnO复合阴极缓冲层减小了ZnO与ITO之间的接触电阻,同时PDA中存在大量的氨基有利于倒置太阳能电池阴极对电子的收集.     

Enhanced power efficiency of ZnO based organic/inorganic solar cells by surface modification

We present series of strategies to enhance efficiency of ZnO nanorods based organic/inorganic solar cells with spin-coated P3HT:PCBM blend as active layer. The performance of the as-fabricated devices is improved by controlling the size of ZnO nanorods, annealing temperature and time of active layer, surface modification of ZnO with PSBTBT. Optimized device of ITO/ZnO nanorod/P3HT:PCBM/Ag device with PSBTBT surface modification and air exposure reaches an efficiency of 2.02% with a short-circuit current density, open-circuit voltage and fill factor of 13.23 mA cm⁻², 0.547 V and 28%, respectively, under AM 1.5 irradiation of 100 mW m⁻², the increase in efficiency is 7-fold of the PSBTBT surface modified ITO/ZnO nanorods/P3HT:PCBM/Ag device compared with the unmodified one, which is own to the increased interface contact, expanded light absorption, tailored band alignment attributed to PSBTBT. We found exposure to air and surface modification is crucial to improve the device performance, and we discussed the mechanisms that affect the performance of the devices in detail.     

Study of a ternary blend system for bulk heterojunction thin film solar cells

In this research, we report a bulk heterojunction(BHJ) solar cell consisting of a ternary blend system. Poly(3-hexylthiophene) P3 HT is used as a donor and [6,6]-phenyl C61-butyric acid methylester(PCBM) plays the role of acceptor whereas vanadyl 2,9,16,23-tetraphenoxy-29 H, 31H-phthalocyanine(VOPc Ph O) is selected as an ambipolar transport material. The materials are selected and assembled in such a fashion that the generated charge carriers could efficiently be transported rightwards within the blend. The organic BHJ solar cells consist of ITO/PEDOT:PSS/ternary BHJ blend/Al structure. The power conversion efficiencies of the ITO/ PEDOT:PSS/P3HT:PCBM/Al and ITO/PEDOT:PSS/P3HT:PCBM:VOPcPhO/Al solar cells are found to be 2.3% and 3.4%, respectively.