MIM结构的SPP模式理论与仿真计算研究

为了进一步明确MIM （Metal-insulator-metal）波导结构的SPP （Surface plasmon polariton）模式特性,建立了MIM结构的SPP模式关系、激发系数和反射系数的理论模型。仿真数值计算结果表明：较大的介质厚度的TM基态模式衰减超过了振荡模式衰减,与传统的介质波导明显不同;TE模式表现为失真的介质光波导模式特性,其传播距离要远大于TM₀;MIM结构中腔的Q值随着长度增加而增大,表明了SPP反射受限;腔的品质因数改变与端面关系密切;MIM波导可以在具有更大Q值下确保光波更好地耦合成需要的SPP模式。     

Phase-matched second-harmonic generation in hybrid polymer-LN waveguides

Here we propose a hybrid polymer-LN waveguide for achieving phase-matched second-harmonic generation (SHG). From the aspect of super-mode theory, the geometric parameters of the hybrid semi-nonlinear waveguide were optimized to utilize both symmetric (even) and antisymmetric (odd) modes of the pump and SHG waves so as to facilitate phase matching with large modal overlap. Phase matching between a fundamental even (TE₀₀-like) mode at 1320 nm and a fundamental odd (TE₀₁-like) mode at 660 nm was found with a calculated modal overlap integral of 0.299, while utilizing the largest nonlinear coefficient d₃₃, and achieving an efficient calculated normalized conversion efficiency of 148% W^-1·cm^-2. Considering the fabrication feasibility of such hybrid waveguide with features including etchless, large dimension, and low structural sensitivity, we believe our findings would provide a useful reference for future on-chip efficient nonlinear conversion devices.     

Phase-matched second harmonic blue light generation in ion implanted KNbO3 planar waveguides with 29% conversion efficiency

We report for the first time to our knowledge, noncritical phase-matched second harmonic generation in an ion-implanted KNbO₃ planar waveguide. The guided TM₀ mode of the fundamental wave (868 nm) is converted into the second harmonic TE₁ mode (434 nm). From 1.3 kW of internal fundamental peak power 385 W second harmonic blue light is generated giving a conversion efficiency of 29%. A comparison of the measured and the theoretical efficiencies implies that phase-matching is achieved over the full waveguide length. Based on these first experimental results we estimate that 100 mW of blue light can be generated from 400 mW of input power using an optimized KNbO₃ planar waveguide of 1 cm length.     

十字结构银纳米线的表面等离极化激元分束特性

金属纳米线波导可以将光局域在亚波长尺度内传播, 在纳米光子集成回路方面有着重要的作用. 本文应用有限元方法, 研究了十字结构银纳米线的表面等离极化激元分束特性. 结果表明, 不同模式的表面等离极化激元在十字结构三个分支的输出依赖于端面的几何结构参数. 此外, 研究还发现由于不同模式表面等离极化激元叠加, 在十字结构的分支上出现了周期性电场分布.     

基于飞秒激光抽运的石墨烯包裹微光纤波导结构的级联四波混频研究

基于石墨烯的光学非线性特性和器件研究正在成为新一代微纳光子器件的一个重要方向. 采用峰值功率为kW量级的飞秒脉冲抽运和P型掺杂石墨烯薄膜包裹的微光纤所构成的复合波导结构, 在1550 nm波段成功激发并观察到级联四波混频现象. 实验 结果表明, 这种P型掺杂石墨烯包裹的微光纤复合波导具有非线性系数高、结构紧凑, 可承受高功率和超快响应的特点, 对基于该结构的级联四波混频特性的研究在基于超快光学的多波长光源、光参量放大以及全光再生等领域具有参考价值和应用意义     

一维金属光栅的光学反射吸收

利用RCWA(rigid coupled-wave analysis)方法研究了一维金属光栅的反射特性,考察了 瑞利反常、表面等离激元驻波共振和几何共振三种共振吸收机理,分析了这三种机理的相互作用,如表面等离激元驻波共振和几何共振可以形成混合模式. 在反射式复合金属光栅中,确认了第四种共振形式,即相位共振. 数值计算表明相位共振对光学吸收的影响有两种形式: 当光栅周期大于一个波长时,相位共振导致尖锐的吸收峰,峰位在几何共振吸收峰一侧;当光栅周期小于一个波长时,相位共振导致混合模式的共振吸收峰发生劈裂. 对一维金属光栅反射特性的研究增加了对金属光栅共振吸收模式及其相互作用的认识. 关键词： 一维金属光栅 瑞利反常 表面等离激元 相位共振     

一种电光可调的铌酸锂/钠基表面等离子体定向耦合器

为了满足日益增加的集成光子器件设计的需求,本文研究了一种铌酸锂/钠表面等离子体波导(Li Nb O3/Na surface plasmonic waveguide, LNSPW),并利用LNSPW构成电光可调的定向耦合器(directional coupling,DC).利用有限元方法 (finite element method, FEM)对波导的模式特性和耦合器的耦合特性进行了分析.结果表明,随着波导尺寸的增大,传播长度可达约200μm,归一化有效模场面积小于0.4.通过调节耦合间距(W_gap)、耦合长度(L_C)和工作波长(λ)等参数,铌酸锂钠表面等离子体波导构建的定向耦合结构可实现3 d B耦合.当W_gap=100 nm和L_C=17μm时, DC在V₀=53 V时可实现3 d B耦合,且具有较好的方向性和隔离度.LNSPW的研究为实现可调的DC提供了一种可行的方案,在集成电光可调器件研究领域有潜在的应用前景.除此之外, LNSPW还可广泛应用于非线性光学、光信号处理及光全...     

Wave dispersion, growth rates, and mode converter analysis for asheet beam, hybrid-mode Cerenkov amplifier

The hybrid-mode dispersion relation and resonant growth rates are solved for a finite-thickness sheet electron beam propagating through a rectangular guide with a thin dielectric slab. Analytic results for the growth rates, bandwidth and mode competition for an infinite magnetic field in the limit of a dilute beam are then presented. To properly couple to the desired EH₁₀ hybrid amplifier slow wave mode, the coupled waveguide mode equations are solved for a dielectric taper to accomplish the TE₁₀ to EH₁₀ mode transition. A piecewide linear taper which suppresses the competing EH₁₁ mode and other hybrid modes is developed and the overall amplifier system is discussed     

Grating polarizers in waveguide miter bends

Rectangular grooved gratings have been fabricated on mirrors of waveguide miter bends. When the HE₁₁ mode was propagated in corrugated waveguide with diameter equal to approximately 12 wavelengths, these gratings performed in the same manner as predicted using plane wave theory. Two gratings with different groove depths in successive miter bends are sufficient to generate a rather wide range of polarizations. These gratings are particularly convenient in waveguide, which offers ease of alignment, compact transverse dimensions, and the possibility of vacuum operation.     

回旋速调管输入耦合器分析与设计

 对Ka波段工作模式为TE₀₁模和TE₀₂模的两种回旋速调管的输入耦合器进行了详细研究,利用模式匹配理论和HFSS建模仿真计算了内圆柱腔和外同轴腔的尺寸;提出了一种与软件计算相结合的模式纯度计算方法,对内腔工作模式纯度、内外腔能量分数进行了计算。内腔侧面上的耦合缝的大小、角向位置都直接决定外同轴腔内的TE_m11模向内圆柱腔的TE_0n1模的耦合情况。针对耦合缝与输入波导成45°和0°分布两种情况,研究了耦合缝长、宽和角向偏移,以及内外腔频差对频率、Q值及内腔能量分数的影响。分别设计了Ka波段内腔工作模式为TE₀₁₁、外腔为TE₄₁₁和内腔TE₀₂₁、外腔TE₈₁₁的两种输入耦合器,并利用矢量网络分析仪对内腔工作模式为TE₀₁₁的耦合器进行了冷高频测量,测得频率为34.257 GHz,与计算结果34.300 GHz仅相差43 MHz。     

Design of a 3-MW 140-GHz gyrotron with a coaxial cavity

A design for a 3-MW 140-GHz gyrotron based on the use of a coaxial cavity is given. The cavity mode is TE_21,13, chosen so that the ohmic heating on both the inner and outer conductors would be low enough for CW operation. The mode selection process, nonlinear, multimode and time-dependent modeling of the beam wave interaction, and gun design are discussed in detail. An inverted magnetron injection gun (MIG) is used to accommodate the inner conductor. The radiation is coupled out via a quasi-optical mode converter, consisting of an irregular cylindrical waveguide section followed by a step-cut launching aperture and a single near-parabolic mirror. The design of these components is also described     

Design of the spot size for single-mode Ti/Mg:LiNbO3, channel waveguide for optimum coupling with fibers

To improve the coupling effciency between fibers and conventional Ti:LiNbO₃ diffused channel waveguides, it is feasible that the elliptical mode pattern of the channel waveguide can be modified by the Ti/Mg double diffusion method. By means of the three-dimensional beam propagation method, we successfully show that the mode size of the waveguide fabricated by this method is well matched to that of the fiber for TE and TM polarizations separately.     

Starspots,stellar cycles and stellar flares: Lessons from solar dynamo models

We theoretically investigate the multistable behavior of a hybrid optomechanical system,in which a charged mechanical resonator is coupled via Coulomb interaction to an optomechanical cavity containing an optical parametric amplifier(OPA).It is shown that the multistable behavior of the mean intracavity photon number can be controlled flexibly by adjusting the nonlinear gain parameter of the OPA,the phase of the field pumping the OPA,the power and frequency of the field driving the cavity,and the Coulomb coupling strength between the two charged mechanical resonators.In particular,the increase of the nonlinear gain parameter can result in a transition from testability to Instability.Moreover,the effect of the Coulomb coupling strength on the bistable behavior of the steady-state positions of the two mechanical resonators is discussed.     

利用窄刻槽金属光栅实现石墨烯双通道吸收增强

构建基底/窄刻槽金属光栅/覆盖层/石墨烯结构,利用金属光栅激发的表面等离子体激元共振和窄光栅刻槽支持的法布里-珀罗共振,在可见光波段实现单层石墨烯的双通道吸收增强,并结合简化模型估算出双吸收通道所在位置.在波长462和768 nm处,石墨烯的光吸收效率分别为35.6%和40.1%,相比石墨烯本征光吸收率的增强均超过15.5倍.进一步研究发现由于短波处吸收增强源于金属光栅的表面等离子体激元共振,其吸收特性受覆盖层厚度、刻槽深度和宽度变化的影响较小;而由于长波处吸收增强源于窄刻槽中的法布里-珀罗共振,因此呈现出良好的角度不敏感吸收特性.     

基于波导模式变换的圆波导TE62模式激励器的研究

基于不规则波导模式匹配法以及缓变波导中电磁波模式耦合理论,研究了一种W波段圆波导TE₆₂模式激励器. 该波导模式激励器采用矩形波导TE₁₀模式通过侧壁耦合馈入同轴波导,利用同轴波导的选模特性激励TE₆₁模式;随后利用轴向半径周期微扰的圆波导实现TE₆₁–TE₆₂模式变换. 文中推导了矩形-同轴波导模式匹配理论,系统研究了波导结构缓变参数对模式变换效率的影响,完成了模式变换器的优化仿真设计,数值计算结果表明：中心频率处TE₆₂模式的转换效率为94.5%,纯度为98.16%,效率85%以上带宽达到1 GHz,能够满足回旋管冷测的要求. 关键词： 同轴波导 模式变换 耦合模理论 半径微扰     

2-μm single longitudinal mode GaSb-based laterally coupled distributed feedback laser with regrowth-free shallow-etched gratings by interference lithography

We report a type-I Ga Sb-based laterally coupled distributed-feedback(LC-DFB) laser with shallow-etched gratings operating a continuous wave at room temperature without re-growth process. Second-order Bragg gratings are fabricated alongside the ridge waveguide by interference lithography. Index-coupled LC-DFB laser with a cavity of 1500 μm achieves single longitudinal mode continuous-wave operation at 20℃ with side mode suppression ratio(SMSR) as high as 24 dB.The maximum single mode continuous-wave output power is about 10 mW at room temperature(uncoated facet). A low threshold current density of 230 A/cm~2 is achieved with differential quantum efficiency estimated to be 93 mW/A. The laser shows a good wavelength stability against drive current and working temperature.     

高功率激光激励下多晶波导薄膜的非线性光学效应

采用光波耦合器和被动锁模微微秒Nd:YAG激光束,在真空沉积的硫化锌波导薄膜中,实现了基波TE₃(ω)模式与二次谐波TE₃(2ω)模式之间的相位匹配。并同时观察到了三次谐波光谱。它们的光谱曲线的半高全宽分别为1.3?和1.4?。在基波入射功率为20MW的情况下,二次谐波的转换效率达1.8×10^-3。 关键词：     

圆波导TE01模激励器设计及实验研究

对比分析了几种可输出圆波导TE₀₁模激励器的仿真设计结果。结果表明,利用行波功分结构实现矩形波导TE₁₀模到4路矩形波导TE₁₀模的等幅同相功分,进而合成转换成圆波导TE₀₁模的转换过程,可在较宽的频带范围内,实现圆波导TE₀₁模的高效激励。以中心频率9.40 GHz仿真设计的圆波导TE₀₁模激励器,在中心频率上的传输效率超过99.9%;在9.08~9.61 GHz的频率范围内,传输效率大于99%。实验测量结果表明,所加工激励器在较宽的频带范围内,传输损耗优于-0.2 dB,与仿真结果的差异主要来自于波导壁面的欧姆损耗和波同转换结构;器件工作频带内平坦特性良好,有利于开展测量工作。     

A proposed 4 GHz, 60 kW transit-time oscillator operating at 18 kVbeam voltage

A high-power transit-time oscillator operating at 4.0 GHz in the cylindrical-cavity TM₀₁₀ mode is proposed. Without requiring an externally applied magnetic field, the oscillator comprises a diode electron gun and a cylindrical cavity that are combined into a single unit that makes for a compact, lightweight device. The transit-time effect, which underlies the operation principle of the oscillator, is examined through a small-signal analysis from which a relation embodying the cavity length, resonant frequency, and cathode voltage is derived. Proper DC voltages of 18 kV are applied to the diode gun which runs in the space-charge-limited regime and produces a 27 A-current hollow electron beam. Output power is extracted axially from the system by aperture coupling the cavity to an external waveguide where outgoing travelling waves with 60 kW peak power are observed by means of 2.5 D particle-in-cell computer simulations     

Stable high-power TE01 gyro-TWT amplifiers

The stability of high power gyro-TWT amplifiers operating in the low-loss TE₀₁ mode of cylindrical waveguide has been studied, Linear theory has been used to determine the threshold start-oscillation beam current for absolute instability in the operating mode and the critical section lengths for the dominant gyro-BWO interactions occurring at various cyclotron harmonics in other waveguide modes. The performance of the amplifier was evaluated with a nonlinear, self-consistent slow-timescale simulation code. Utilizing interaction sections whose lengths are less than the threshold start-oscillation length and are separated by attenuating severs for isolation, two stable three-section devices have been designed which are predicted to yield: (1) a peak output power of 230 kW at 35 GHz with an efficiency of 23%, a saturated gain of 46 dB and a constant-drive bandwidth of 6% for a 100 kV, 10 A electron beam with an α=ν_⊥ /ν_z =1.0 and an axial velocity spread Δν_z/ν_z=5% and (2) 105 kW at 94 GHz with 21% efficiency, 45 dB saturated gain and 5% constant-drive bandwidth for a similar 5 A electron beam. In addition, the design of the 0 dB input/output couplers and the MIG electron gun are given. Due to the low loss of the TE₀₁ mode, both of these amplifiers can be operated continuously