The effect of proximity of the landing gear lights on its turbulent wake

A simplified model of a landing gear is tested in a wind tunnel to investigate the effect of the landing light location on the resulting noise generation. Examination of the near-field pressure fluctuations, combined with phase-locked stereoscopic particle imaging velocimetry of the unsteady wake identified two distinct sources of pressure fluctuations. The higher frequency source has a wide frequency band and is situated in the outer regions of the wake near the lights. On the other hand, the lower frequency source is found to be stronger, has a narrower frequency band and is developed further downstream in the wake, closer to the wake centreline. The lower frequency source is observed to be rather robust as it is hardly affected by the location of the landing lights, whereas the higher frequency source becomes weaker as the spacing between the lights is reduced. The effect of a splitter plate positioned downstream of the landing gear strut is also investigated as a means of reducing the lower frequency pressure fluctuations. Although the lower frequency source is considerably weakened by the splitter plate, substantial enhancement of the higher frequency source is observed.     

基于传声器阵列过顶测量结果的飞机起落架噪声研究

应用由111个传声器组成的平面传声器阵列对当前流行的民用客机进场着陆过程中的机体噪声源进行了实验测量,本对七架窄体客机和七架宽体客机的起落架噪声进行了分析,得到了起落架噪声的频谱特性、指向特性和声级变化。研究发现,起落架噪声的频谱是由宽频随机噪声与一些较为明显的单噪声源组成,起落架噪声的指向性类似于一个水平放置的偶极子。不同飞机起落架噪声的声级相差较大,这说明可以通过重新结构设计降低起落架噪声。     

Fan interaction noise reduction using a wake generator: experiments and computational aeroacoustics

A control grid (wake generator) aimed at reducing rotor-stator interaction modes in fan engines when mounted upstream of the rotor has been studied here. This device complements other active noise control systems currently proposed. The compressor model of the instrumented ONERA CERF-rig is used to simulate suitable conditions. The design of the grid is drafted out using semi-empirical models for wake and potential flow, and experimentally achieved. Cylindrical rods are able to generate a spinning mode of the same order and similar level as the interaction mode. Mounting the rods on a rotating ring allows for adjusting the phase of the control mode so that an 8 dB sound pressure level (SPL) reduction at the blade passing frequency is achieved when the two modes are out of phase. Experimental results are assessed by a numerical approach using computational fluid dynamics (CFD). A Reynolds averaged Navier-Stokes 2-D solver, developed at ONERA, is used to provide the unsteady force components on blades and vanes required for acoustics. The loading noise source term of the Ffowcs Williams and Hawkings equation is used to model the interaction noise between the sources, and an original coupling to a boundary element method (BEM) code is realized to take account of the inlet geometry effects on acoustic in-duct propagation. Calculations using the classical analytical the Green function of an infinite annular duct are also addressed. Simple formulations written in the frequency domain and expanded into modes are addressed and used to compute an in-duct interaction mode and to compare with the noise reduction obtained during the tests. A fairly good agreement between predicted and measured SPL is found when the inlet geometry effects are part of the solution (by coupling with the BEM). Furthermore, computed aerodynamic penalties due to the rods are found to be negligible. These results partly validate the computation chain and highlight the potential of the wake generator system proposed.     

ARJ21客机降落阶段起落架噪声试验研究

为了测量ARJ21客机的起落架噪声,在飞行现场分别采用改进的频域波束形成和解卷积算法对降落阶段的起落架噪声进行了测量。通过比较两种算法发现,解卷积算法比改进的频域波束形成算法具有更好的声源识别能力。为了提高传声器的利用率,设计了多臂螺旋阵,并且利用线性插值消除了多普勒效应。根据主起落架和前起落架的分布位置不同,将声源识别区域划分为两部分,在140—800Hz范围内对不同频段的1/3倍频程的起落架噪声进行了测量。结果发现:在250 Hz以上频段,主起落架为主要噪声源,且在中心频率500 Hz的1/3倍频程内为唯一强声源;前起落架在中心频率630 Hz的1/3倍频程内为主要噪声源。通过试验得到了主起落架和前起落架噪声在不同频段的分布特点,为起落架降噪设计提供了支持。      

基于前视跑道图像的飞机偏心距精确测量

根据飞机地面最小操纵速度试飞的光电测试需求,提出一种基于前视跑道图像的飞机偏心距精确测量技术,通过在飞机中后段机腹中心线上加装前视高速数字摄像机,获取飞机运动时跑道及飞机起落架的前视序列图像,通过图像判读获取飞机主起连线与跑道标识线交点的亚像素坐标,在摄像机测量参数高精度标定的基础上,根据摄影测量的单站定位原理精确解算交点在物方空间坐标系下的坐标,进而获取飞机偏离跑道中心线的距离。飞行试验测试结果表明,该测量方案切实可行,数据直观可靠,可实现3 cm的测量精度,完全满足试飞测试任务需求。     

Use of adjacent jets to investigate the aerodynamic sound of airfoils at moderately high Reynolds numbers

A new experimental set-up is proposed to investigate the noise generated by airfoils. It consists of two adjacent plane jets ducted into an anechoic room, and the airfoils under investigation are placed in the median jet. Besides the benefit in the acoustical conditions of the experiments (decrease of the background noise due to the jets, shift of the preferred frequencies of the jets below the range of interest for the airfoil emission), the aerodynamic situation itself is improved (increase in length of the potential zone, decrease of induced flow fluctuations). There is therefore the possibility to investigate airfoil noise with longer chords and higher incident velocities.     

High-speed video analysis of flame oscillations along a PMMA rod after stagnation region blowoff

During blowoff extinction of clear cast PMMA rods in concurrent axial flow for microgravity BASS-II experiments, a dynamic flame oscillation was observed after the flame was blown off of the stagnation point but briefly stabilized on the periphery of the rod. Complementary normal gravity experiments were conducted and flame oscillations were tracked using a high-speed color camera at 240 frames per second. The side-stabilized flame oscillated up and down the rod with increasing amplitude until the entire flame extinguished. In none of the BASS-II or normal gravity tests could the side-stabilized flames persist (Hopf subcritical bifurcation). Since the oscillations occurred even in microgravity, the mechanism does not depend on gravity. For the larger fuel radius tests, the flame developed asymmetric oscillation (pitchfork bifurcation). The oscillation time and the number of oscillations scale with the inverse square of the rod radius (～ Fourier no.) for the preheated microgravity rods. The average flame oscillation frequency is found to be linearly dependent on the mixed convective stretch rate (inverse of the flow time). The flame intensity varied in concert with its direction, either increasing or decreasing as the flame moved upstream or downstream, respectively. The oscillation frequency decreased as the amplitude increased and the flame slipped slightly farther down the rod with each oscillation. The flame speed increased with each subsequent oscillation, both flashing forward upstream and retreating downstream. The oscillations were found to closely follow a power law log-periodic dependence similar to those that describe systems approaching a critical point, such as diffusion-limited aggregation clusters, earthquakes, ruptures, and even stock market crashes. The net flame speeds varied linearly with ambient oxygen concentration, and linearly with the mixed convective stretch rate. Based on these observations, a mechanistic theory of the oscillations is described, and is consistent with the thermodiffusive instability.     

Obtaining absolute acoustic spectra in an aerodynamic wind tunnel

Cost effective methods for identifying and reducing sources of noise have become essential in the design of many modern transport vehicles. Whilst closed-section wind tunnels can readily evaluate aerodynamic performance, obtaining accurate acoustic spectra is often a major challenge because of the poor signal to noise ratios available. In this paper, methods of obtaining absolute spectra from the non-acoustically treated Markham wind tunnel at the University of Cambridge are discussed. Initial measurements with a small monopole source compare well with simulations and show that it is possible to obtain similar spectra from two nested acoustic arrays. However, a series of further experiments with simplified landing gear models show very different spectra from each array. By comparing measurements with simulations, it is shown that negative side lobes affect beamforming source maps. Measurements of an ‘empty tunnel’ cross spectral matrix allow the removal of sidelobes, providing much greater consistency between spectra. Finally, a dipole beamforming vector is used to account for the directivity of the landing gear noise, leading to good agreement between absolute spectra from the differently sized arrays. This analysis demonstrates that data from a phased array in a hard-walled, aerodynamic wind tunnel can provide meaningful acoustic spectra from low-noise models.     

Design and performance of a small-scale aeroacoustic wind tunnel

The D5 aeroacoustic wind tunnel at Beihang University is a newly commissioned small-scale closed-circuit wind tunnel with low turbulence intensity and low background noise. The wind tunnel is built to study both aerodynamic and aeroacoustic performance of aircraft components or scaled models. The wind tunnel has two types of test sections, the closed type test section is used for aerodynamic tests while the open type test section is mainly used for aeroacoustic experiments. Both types of test section are 1 m in height and 1 m in width, and the maximum wind velocity in the test section can be up to 80 m/s. An anechoic chamber is built surrounding the test section to provide the non-reflecting condition. This paper provides an overview of design criteria and performance of the small-scale wind tunnel. The layout of the wind tunnel and some critical design treatments to improve aerodynamic and acoustic performance are discussed in detail. Some experiments are conducted to verify the performance of D5 wind tunnel, results confirm that the turbulence intensity is less than 0.08% in the core of test section and the background noise is comparable with other aeroacoustic wind tunnels. A scaled simplified nose landing gear model is also measured as a benchmark test, results reveal that noise radiated from the model is adequately higher than the background noise for a wide frequency range and remarkably consistent with other results from literatures.     

Visualization of impinging supersonic free jet on a tilt plate by LIF and PSP

The flow field structures of low density supersonic free jets impinging on a tilt plate are studied by hybrid use of LIF (Laser Induced Fluorescence) and PSP (Pressure Sensitive Paint). The jet through an orifice flows into a low pressure chamber and impinges on the tilt plate with angle from jet axis 45, 60 or 90 degrees. A plane including the jet axis and the normal of the plate is visualized by LIF of seeded iodine molecules, scanning a laser beam along the jet axis. On the other hand, the pressure distribution on the tilt plate is visualized by PSP. In comparing the results of the two methods, the complicated shock wave system is analyzed. Deformations of the Mach disk and the barrel shock are also confirmed.     

Prediction of aerodynamic noise reduction by using open-cell metal foam

As the speed of high-speed train (HST) increases continuously, aerodynamic noise has become more remarkable compared with the wheel/rail noise, which affects the inhabited environment along the railway and the riding comfort. This paper preliminarily investigates the feasibility of using open-cell metal foam covering layer to reduce the low Mach number aerodynamic noise generated by the flow around a circular cylinder which is the typical section of pantographs. The aerodynamic noises radiated from the circular cylinder with and without metal foam are calculated. The hybrid method combining two-dimensional large eddy simulation (LES) with Ffowcs Williams–Hawkings (FW–H) equation is employed. The calculated Strouhal number, time-averaged drag coefficient, base pressure and overall sound pressure level agree well with some available experimental data. Then, the influences of metal foam porosity, pore density, thickness of covering layer and the speed of train on the aerodynamic noise and the aerodynamic forces are investigated, and some detailed comparisons of flow field are made. The numerical results indicate that as a passive scheme, the open-cell metal foam with high porosity can modify the flow, adjust the vortex shedding frequency and regularize the wake, leading to a significant reduction of aerodynamic noise. The results are expected to provide useful information for the control of aerodynamic noise using this new material.     

Measurements of aerodynamic noise and wake flow field in a cooling fan with winglets

The aerodynamic noise and the wake flow field in a cooling fan under actual operating conditions are studied with and without winglets on the fan blades. In order to understand the influence of the winglet, the aerodynamic noise and the wake velocity distribution are measured. The results indicated that overall noise level decreased and the noise spectrum was changed in a low frequency range when the winglet was installed. It was found from the flow visualization and PIV measurement that the influence of the winglet appeared in the traces of the tip vortices and the magnitude of vorticity was reduced in the near wake region, which suggest the observed reduction in aerodynamic noise     

Acoustic and aerodynamic design and characterization of a small-scale aeroacoustic wind tunnel

The aeroacoustic wind tunnel at Brandenburg University of Technology at Cottbus is a newly commissioned research facility for the experimental study of sound generation from bodies immersed in a fluid flow. The paper discusses the design criteria for the open jet wind tunnel that provides a maximum wind speed of 72 m/s at continuous operation and may be operated with nozzles of different dimension between 35 cm diameter (circular nozzle) and 12 cm by 14.7 cm (rectangular nozzle). Experiments may be performed either in a reverberant or in an anechoic environment. Both the aerodynamic and the acoustic design of the wind tunnel components are discussed in detail. Background noise measurements in the completed facility revealed very low levels comparable to other wind tunnels. The results of aerodynamic wind tunnel calibration confirmed a uniform flow quality in the jet and a very low axial turbulence intensity which is less than 0.2% for the 35 cm nozzle and less than 0.1% for the other nozzles. A final benchmark is provided by results of successful trailing edge noise measurements on an SD7003 airfoil that are presented and compared to results from the literature.     

Flow Characteristics of Flapping Motion of a Plane Water Jet Impinging onto Free Surface

A submerged turbulent plane jet in shallow water impinging vertically onto the free surface will produce a large-scale flapping motion when the jet exit velocity is larger than a critical one. The flapping phenomenon is verified in this paper through a large eddy simulation where the free surface is modeled by volume of fluid approach. The quantitative results for flapping jet are found to be in good agreement with available experimental data in terms of mean velocity, flapping-induced velocity and turbulence intensity. Results show that the flapping motion is a new flow pattern with characteristic flapping frequency for submerged turbulent plane jets, the mean centerline velocity decay is considerably faster than that of the stable impinging jet without flapping motion, and the flapping-induced velocities are as important as the turbulent fluctuations.     

Design and performance of an open jet wind tunnel for aero-acoustic measurement

This paper presents the design and performance of an open jet, blow down wind tunnel that was newly commissioned in the anechoic chamber at the ISVR, University of Southampton, UK. This wind tunnel is intended for the measurement of airfoil trailing edge self-noise but can be extended to other aeroacoustic applications. With the primary objectives of achieving acoustically quiet and low turbulence air jet up to 120 m/s through a 0.15 m × 0.45 m nozzle, several novel noise and flow control techniques were implemented in the design. Both the acoustical and aerodynamic performances of the open jet wind tunnel were examined in detail after its fabrication. It is found that the background noise of the facility is adequately low for a wide range of exit jet velocity. The potential core of the free jet is characterized by a low turbulence level of about 0.1%. Benchmark tests by submerging a NACA0012 airfoil with tripped and untripped boundary layers at 0° and 10° angles of attack respectively into the potential core of the free jet were carried out. It was confirmed that the radiating airfoil trailing edge self-noise has levels significantly above the rig noise over a wide range of frequencies. The low noise and low turbulence characteristics of this open jet wind tunnel are comparable to the best facilities in the world, and for its size it is believed to be the first of its kind in the UK.     

Aeroacoustic performance evaluation of axial flow fans based on the unsteady pressure field on the blade surface

Because of the European and global regulation concerning acoustic emission, the goal of manufacturers is to substantially decrease the noise radiated by turbomachines, and in particular axial fans, without degrading their aerodynamic performances. High rotation speed and increasing power add to the overall difficulties. The theoretical study of this paper consists of two parts: (1) an aerodynamic approach based on the vortex surface method and (2) an aeroacoustic approach which mainly concerns the prediction of the tonal noise using the Ffowcs Williams and Hawkings (FW-H) equation. One of the main goals is the evaluation of the unsteady aerodynamic forces applied on the fan blades. A 2D software analysis, based on the vortex surface method (or potential flow method), was carried out. That process enabled evaluation of the potential flow around a mobile grid; first in a steady mode, and secondly in an unsteady mode by introducing an upstream disturbance in the form of an inlet velocity variation. The sources of noise corresponding to the zones with high force fluctuation amplitude are located initially on the blade surface. These fluctuating forces are used to predict the tonal noise radiated by the fan in far field by means of the FW-H equation. Two axial flow fans were used in this study. The theoretical results will be compared to the experimental ones in order to evaluate the aeroacoustic performances of the fans.     

发动机喷流对火箭气动特性影响

开展了考虑底部发动机喷流影响的火箭气动特性CFD仿真设计,比较了有/无喷流时火箭附近流场结构、表面压力分布、整体气动力/力矩特性在亚/超声速段的差异,结果显示,发动机喷流对火箭亚声速段的轴向力、法向力和俯仰力矩特性均有较为显著的影响,且有减小尾部空气舵气动控制力矩的影响,而超声速段的影响仅限于轴向力。该仿真结果与飞行试验气动辨识结果较为一致。基于仿真分析结果,可建立一种折中考虑喷流影响的气动特性设计方法,供火箭精细化气动特性设计参考使用。      

Measurement of aerodynamic noise and unsteady flow field around a symmetrical airfoil

The purpose of this paper is to study the physics of aerodynamic noise generation from the symmetrical airfoil of NACA 0018 in a uniform flow. The relationship between the noise spectrum and the unsteady flow field around the airfoil is studied in an acoustic wind tunnel using flow visualization and PIV analysis. The discrete frequency noise was generated from the airfoil inclined at small angle of attack to the free stream. The flow visualization result indicates the presence of attached boundary layer over the suction side and the separated shear layer over the rear pressure side of the airfoil, when the discrete frequency noise is observed. It is found from the PIV analysis that a large magnitude of vorticity is generated periodically from the pressure side of the trailing edge and it develops into an asymmetrical vortex street in the wake of the airfoil. The periodicity of the shedding vortices was found to agree with that of the frequency of the generated noise.     

棒-环电极大气压等离子体射流的光谱特性

通过设计新型的交流电压激励的氩气等离子体射流,在棒电极的上游与下游区域均产生了大气压非平衡态等离子体羽。该射流与平行场射流和交叉场射流不同,它的电场与气流方向的夹角可以在一定范围内变化。结果表明,随着外加电压或夹角的增加,上游羽的长度增加而下游羽的长度减小。利用光学和电学的方法,研究发现随着外加电压的增加,上下游放电脉冲的个数均增加。利用放电的光学发射谱,发现上游羽有Ar和OH的谱线,而下游羽除了Ar和OH的谱线外,还可以观察到N₂的谱线。并且下游羽的谱线强度比上游羽的略高。基于碰撞辐射模型,通过谱线强度比的方法研究了上下游羽的电子密度和电子激发温度。结果表明上下游羽的电子密度随着外加电压的增加而增加。上下游羽的电子激发温度也随着外加电压的增加而增加。并且,在同一外加电压时下游羽的电子密度和电子激发温度均比上游羽的高。此外,利用OH发射光谱研究了上下游羽的气体温度,发现下游羽的气体温度也比上游羽的略高。     

Aerodynamic measurement of a large aircraft model in hypersonic flow

Accurate aerodynamic measurements in the hypersonic flow of large aircraft models in tunnels have practical significance, but pose a significant challenge. Novel aerodynamic force measurement methods have been proposed,but lack theoretical support. The forms of the force signals techniques for signal processing and calculation of aerodynamics are especially problematic. A theoretical study is conducted to investigate the dynamic properties based on models of the draw-rod system and slender rods. The results indicate that the inertia item can be neglected in the rod governing equation;further, the solutions show that the signals of each rod are a combination of aerodynamic signals(with a constant value) and sine signals, which can be verified by experimental shock tunnel results. Signal processing and aerodynamics calculation techniques are also found to be achievable via the flat part of the signals.