IR Spectroscopic Investigations of Gasochromic and Electrochromic Sol-Gel—Derived Peroxotungstic Acid/Ormosil Composite and Crystalline WO3 Films

We studied the gasochromic effect of amorphous peroxopolytungstic acid (W-PTA), W-PTA (ormosil) and crystalline WO₃ films. These latter films were prepared after a heat treatment of W-PTA/ormosil films at 450°C. The ormosil served as a template, providing the monoclinic WO₃ films with adequate porosity. The spill-over effect was attained by impregnating the porous WO₃ crystalline films with H₂PtCl₆ followed by a heat treatment at 380°C. The amorphous films became gasochromic with the addition of PdCl₂ to the corresponding W-PTA and W-PTA/ormosil sols.Structural features of all the films were studied with the help of infrared (IR) spectroscopy and transmission electron microscopy (TEM). In situ IR spectra of the films, performed in the presence of reducing (H₂/Ar) and oxidising (O₂/Ar) gases, revealed a reversible transformation of the monoclinic to the tetragonal H _x WO₃ phase. At the same time the coloration (reduction) of the amorphous films was accompanied by the formation of coordinated water molecules and increased numbers of W=O bonds. Gasochromic colouring/bleaching changes and the corresponding kinetics were assessed from in situ UV-visible transmission measurements on the films.     

介孔氧化钨电色薄膜的制备与性能研究

采用一种新的非离子型gemini表面活性剂结构导向模板, 成功制备了介孔氧化钨薄膜. 通过SAXRD, TEM和N₂吸附-脱附等方法考察薄膜的制备和微结构特性, 发现获得的产物具有三维蠕虫介孔结构, 比表面积可达145.5 m²• g^－1. 测定了该薄膜在无水高氯酸锂/碳酸丙烯酯电解质溶液中的循环伏安和电致变色性能, 并与无模板薄膜进行了对比研究. 研究表明, 由于具有更大的电化学活性比表面, 纳米介孔氧化钨薄膜表现出增强的电色性能, 在633 nm波长处的透过率调制幅度可达60%以上, 着色效率为51.7 cm²•C^－1.     

Structural, Vibrational, and Gasochromic Properties of Porous WO3 Films Templated with a Sol-Gel Organic–Inorganic Hybrid

 The structure and the gasochromic properties of sol-gel-derived WO₃ films with a monoclinic structure (m-WO₃) were studied by focusing attention on the size of the monoclinic grains. The size of the m-WO₃ grains is modified by the addition of an organic–inorganic hybrid to the initial peroxopolytungstic acid (W-PTA) sols which are based on chemically bonded poly-(propylene glycol) to triethoxysilane end-capping groups (ICS-PPG). The results obtained with scanning electron microscopy (SEM) and transmission electron microscopy (TEM) show that the heat treatment (500°C) of WO₃/ICS-PPG (0.5, 1, 2, 5, and 10 mol%) composite films results in a change of their morphology, and nanodimensional pores are formed between the grains. High-resolution TEM (HRTEM) analysis revealed the presence of an amorphous phase on the outside of the m-WO₃ grains, whereas energy-dispersive X-ray spectra (EDXS) showed that this amorphous phase contained W and Si. Impregnation of the WO₃/ICS-PPG film with H₂PtCl₆/i-propanol solution followed by heat treatment at 380°C gave the films their gasochromic properties. Infrared and Raman spectroscopic studies of the WO₃/ICS-PPG film confirmed the results of the corresponding HRTEM and EDXS analysis. In situ UV/Vis and in situ IR spectra of the films were measured in hydrogen and in air, and colouring/bleaching changes and the corresponding kinetics were assessed. The IR spectra of gasochromically coloured films showed that the mesoporous WO₃/ICS-PPG (1 mol%) film transforms to tetragonal H _x WO₃ bronze. The IR spectra of the H _x WO₃ bronze are discussed with the aim to establish the existence of the metal-OH vibrations of gasochromically formed oxyhydroxide tungsten bronze.     

Structural,Vibrational, and Gasochromic Properties of Porous WO<Subscript>3</Subscript> Films Templated with a Sol-Gel Organic–Inorganic Hybrid

Summary.  The structure and the gasochromic properties of sol-gel-derived WO₃ films with a monoclinic structure (m-WO₃) were studied by focusing attention on the size of the monoclinic grains. The size of the m-WO₃ grains is modified by the addition of an organic–inorganic hybrid to the initial peroxopolytungstic acid (W-PTA) sols which are based on chemically bonded poly-(propylene glycol) to triethoxysilane end-capping groups (ICS-PPG). The results obtained with scanning electron microscopy (SEM) and transmission electron microscopy (TEM) show that the heat treatment (500°C) of WO₃/ICS-PPG (0.5, 1, 2, 5, and 10 mol%) composite films results in a change of their morphology, and nanodimensional pores are formed between the grains. High-resolution TEM (HRTEM) analysis revealed the presence of an amorphous phase on the outside of the m-WO₃ grains, whereas energy-dispersive X-ray spectra (EDXS) showed that this amorphous phase contained W and Si. Impregnation of the WO₃/ICS-PPG film with H₂PtCl₆/i-propanol solution followed by heat treatment at 380°C gave the films their gasochromic properties. Infrared and Raman spectroscopic studies of the WO₃/ICS-PPG film confirmed the results of the corresponding HRTEM and EDXS analysis. In situ UV/Vis and in situ IR spectra of the films were measured in hydrogen and in air, and colouring/bleaching changes and the corresponding kinetics were assessed. The IR spectra of gasochromically coloured films showed that the mesoporous WO₃/ICS-PPG (1 mol%) film transforms to tetragonal H _x WO₃ bronze. The IR spectra of the H _x WO₃ bronze are discussed with the aim to establish the existence of the metal-OH vibrations of gasochromically formed oxyhydroxide tungsten bronze. Received October 4, 2001. Accepted (revised) November 19, 2001     

Gasochromic Behavior of Sol-Gel Derived Pd Doped Peroxopolytungstic Acid (W-PTA) Nano-Composite Films

The behavior of sol-gel prepared thin films exhibiting a gasochromic effect; i.e., a reversibly change in colour from transparent when in air to blue when in H2, has been studied. The films were prepared from a Pd (PdCl2) doped peroxopolytungstic acid sol using a dip-coating technique. Transmission electron microscopy together with selected area electron diffractrometry revealed that the films consist of monoclinic and hexagonal nanocrystalline grains (2–5 nm) embedded in an amorphous phase. This amorphous hydrated phase was established using Infrared (IR) and Raman spectroscopy. Characteristic vibrations observed in the in-situ IR spectra of the coloured and bleached states revealed the presence and the importance of terminal W=O and W—OH2 groups in the colouring of the films. Colouring/bleaching changes of Pd doped W-PTA films observed using in-situ UV-Vis spectroscopy are described in terms of Pd concentration, and the number of reducing/oxidising cycles. The rate of colouring/bleaching is greater for films containing a higher concentration of Pd but the change in the optical density does not increase, i.e., shows saturation.     

Synthesis and Characterization of Macroporous Tungsten Oxide Films for Electrochromic Application

Macroporous tungsten oxide films have been prepared by combining a nonhydrolytic sol-gel method with a molecular assembly templating strategy. The material has been prepared by hydrolysis of an ethanolic solution of tungsten ethoxide in the presence of polyethylene glycol (PEG), followed by calcination of the dip-coated films. AFM images indicated that an important morphological diversity can be obtained by simply varying the amount of PEG in the coating solution and the conditions of the heat-treatment. The formation of nanostructures of controlled shapes and patterns (fibrils or striped phases) with relatively uniform channel spacings is accounted for by strong hydrogen bonding interactions between the PEG and the partially hydrolyzed tungsten oxide oligomers. XRD and FTIR data showed that PEG delays the crystallization of WO₃. When compared to sol-gel prepared tungsten oxide fims prepared without PEG, the coloration efficiency of the macroporous films appears to be significantly improved especially in the near-infrared region.     

多酸含量对无机/高分子复合薄膜结构及光致变色性能的影响

制备了一系列不同浓度的钨磷酸/聚乙烯醇(PWA/PVA)复合薄膜, 通过红外光谱、原子力显微镜、紫外-可见吸收光谱对复合薄膜的结构和光致变色性能进行了研究. 红外光谱分析结果表明, Keggin结构钨磷酸和聚乙烯醇分子的基本结构在复合薄膜中仍然存在, 钨磷酸分子与高分子底物间存在氢键作用, 形成电荷转移桥. 原子力显微镜(AFM)结果表明复合前后PVA薄膜表面形貌发生了显著变化, 复合膜表面形貌随钨磷酸含量的不同而不同. 在紫外光照射下, 复合薄膜由无色变为蓝色. 复合膜的升色速度和褪色速度均随着钨磷酸含量的增加而加快. 这些结果表明钨磷酸含量对复合膜的微结构存在影响, 从而导致了复合膜具有不同的光致变色性能.     

Color Stabilization of Polyvinyl Chloride) with Heat Treatment

Stabilization of polyvinyl chloride) (PVC) containing metal soaps was investigated by psychophysical colorimetry. A color difference observed among heated PVC films containing various metal salts depends on coloration of the π-complex of polyene with metal chloride converted from the metal salt added and that the stabilization effect of synergistic soaps should be based on an effect of complementary colors set up among a polyene color and metal chloride-polyene complex colors. These conclusions are well supported by colorimetry of heated PVC films containing various dyes. The color of heated PVC films containing Zn/Ca and Cd/Ba synergetic soaps markedly deviated from a polyene color with increased heat treatments, owing to greater degree of coloration of Zn complex and Cd complex, respectively. These color deviations usually decrease the thermal stability of PVC. The thermal stability of PVC was markedly improved by the use of synergetic soaps together with masking agent such as triethanolamine, urea, N,N′-dimethylol-urea, and vinylpyridine-methylmethacrylate copolymer, owing to the masking effect of these nitrogen-containing compounds. These masking agents did not slow down the dehydrochlorination of PVC.     

有机铵十聚钨酸盐在溶液中的光致变色性质研究

有机铵十聚钨酸盐具有显著的光致变色性质,电子自旋共振研究表明光致变色是由于光照过程中有五价钨生成,发生了光还原反应。本文研究了二异丙胺和六氢吡啶十钨酸盐(分别简写为DIAW_(10)和PIPDW_(10)在溶液中的光致变色性质,考察了水、乙腈、二甲基甲酰胺(DMF)、二甲基亚砜(DMSO)对光致变色性质的影响,对比研究了四丁基铵盐(NBuW_(10))的情况,还测定了不同光照时间下W(V)浓度,可见吸收光谱和循环伏安,提出了光致变色性质与体系中所含活泼氢的定量关系,初步揭示有机铵十聚钨酸盐光致变色的本质。     

Fourier transform surface-enhanced Raman scattering of single-layer nucleolipid Langmuir-Blodgett films on silver island film substrates

Surface-enhanced Raman scattering (SERS) spectra of four amphiphilic nucleolipids in single-layer Langmuir-Blodgett (LB) films deposited on silver island film substrates from pure water and complementary nucleotide-containing subphase and corresponding powder normal Raman spectra were obtained. The analysis of these spectra indicates that the SERS effect is mainly caused by a charge-transfer mechanism, and only the nucleobase headgroup moieties and complementary bases combined with them through hydrogen bonds, which are directly in contact with the silver island film substrates, could be enhanced. For the amphiphilic nucleolipids with the identical nucleobase headgroups, the SERS spectra of the LB films are similar, implying that the orientations of these nucleobase moieties on the silver substrates are analogous. However, the nucleobase takes different orientations on the silver substrates before and after complementary binding. The nucleobases in the LB films deposited from pure water are nearly lying flat on the silver surface, while the complementary binding pairs transferred from the air/water interface tend to take an end-on orientation on the metal surface.     

Investigation on the effects of beta and gamma irradiation on conducting polymers for sensor applications

Two conductive polymers were evaluated to be the active materials in a sensor device for the detection of beta radiation. This was accomplished by characterizing the changes in conductivity of electrically conducting polymer films caused by exposure to tritium gas for varying lengths of time. The behavior of these materials when exposed to gamma radiation was also studied to gain further insight into the mechanism of conductivity degradation by ionizing radiation. Two types of conductive polymer, polyaniline (PANi) and poly(3,4-ethylenedioxythiophene) (PEDOT), were chosen as candidate materials for their widespread commercial use. The change of surface resistance (conductivity) of PANi and PEDOT films when exposed to gamma radiation in both air and deuterium environments was evaluated as well as tritium exposures in 10⁴ and 10⁵ Pa gas. Raman and absorbance spectra of gamma irradiated samples were obtained to determine the mechanism of conductivity degradation in both polymers. Post-irradiation gas analysis of the samples contained in deuterium revealed very little (or no) hydrogen in the containment vessel, indicating that hydrogen–deuterium isotopic exchange was not responsible for the decrease in surface conductivity due to gamma exposure. The effects of irradiation-induced oxidation were also studied for both conductive polymers during gamma irradiation. It was concluded that chain scission via free radical formation and chain cross-linking are most likely the two dominant mechanisms for conductivity change and not de-protonation of the polymer.     

Fabricating polypyrrole/tungsten oxide hybrid based electrochromic devices using different ionic liquids

A facile approach of polypyrrole (PPy)/tungsten oxide (WO₃) composites electrosynthesized in ionic liquids for fabrication of electrochromic devices is discussed. The electrochromic properties of PPy/tungsten oxide nanocomposite films (PPy/WO₃) prepared in the presence of four different ionic liquids, 1‐butyl‐3‐methylimidazolium tetrafluoroborate (BMIMBF₄), 1‐butyl‐3‐methylimidazolium hexafluorophosphate (BMIMPF₆), 1‐butyl‐3‐methylimidazolium bis(trifluoromethylsulfonyl) imide (BMIMTFSI), and 1‐butyl‐1‐methylpyrrolidinium bis(trifluoromethylsulfonyl) imide (BMPTFSI) were investigated in detail. Cyclic voltammetry results revealed that PPy/WO₃ nanocomposite films have much more electrochemical activity than those of WO₃ and PPy film. The electrochromic contrast, coloration efficiency, and switching speed of the composite films were determined for electrochromic characteristics. The maximum contrast and the maximum coloration efficiency values were measured as 33.25% and 227.89 cm²/C for the PPy/WO₃/BMIMTFSI composite film. Copyright © 2015 John Wiley & Sons, Ltd.     

固相配位化学反应研究LXVII．金属铜表面M－S（M＝Mo，W）簇合物膜的组成

采用ＦＴＩＲ、ＸＰＳ和ＡＥＳ研究了金属铜表面Ｍ－Ｓ（Ｍ＝Ｍｏ，Ｗ）簇合物膜。结果表明，Ｍｏ（Ｗ）与铜表面的Ｃｕ＿２Ｏ反应，形成了Ｍｏ（Ｗ）－Ｓ－Ｃｕ键；簇合物膜由Ｍｏ（Ｗ）、Ｓ、Ｃｕ、Ｏ元素组成，分别呈＋６、－２、＋１、－２价，膜为多分子层结构并保持ＭｏＳ＿４，或ＷＳ＿２单元，膜表面只有Ｃｕ、Ｏ而不存在Ｍｏ（Ｗ）、Ｓ．膜层厚度与反应时间有关，时间越长，膜越厚。膜为多组分的复杂体系，其颜色是各组分统计分布的结果。     

Molecularly organized Langmuir-Blodgett films from a ruthenium biphosphine complex

Langmuir-Blodgett (LB) films from a ruthenium complex mer-[RuCl3 (dppb)(4-Mepy)] (dppb = PPh2 (CH2)4PPh2; 4-Mepy = 4-methylpyridine), termed Ru-Pic, display a distinct color, which is different from the coloration exhibited by cast films or chloroform solutions. The solution and cast films are red, while the LB films are green-bluish. The manifestation of the blue color in the LB film finds its explanation in a unique absorption band at 690 nm, which is associated with the oxidation of the phosphine moieties. Fluorescence emission and absorption-reflection infrared spectroscopy measurements revealed the molecular organization in the LB films. In contrast, cast films showed a random distribution of complexes. Surface-enhanced Raman scattering was also used in an attempt to identify the main interactions in Ru-Pic.     

Study of chemical bonds in a-B/C:H films by electron probe microanalysis

This paper describes the study of chemical bonds in amorphous hydrogen rich boron/carbon (a-B/C:H) films by electron probe microanalysis. The films were deposited on Si single crystals by plasma chemical vapour deposition with a precursor-carborane (C₂B₁₀H₁₂) in a laboratory setup. A film thickness and B/C ratio up to a value of 8000 Å and 4, respectively, have been obtained. The analysis of boron and carbon X-ray emission spectra has shown that the nearest order in the films is characterized by the coexistence of C-C, B-C and B-B bonds for B/C 1 and of B-B and B-C bonds for B/C 4. After two years exposure in air the oxygen content in the films increases from 2–5 to 15–20 at.%.     

Properties stability and biodegradation behaviors of soy protein isolate/poly (vinyl alcohol) blend films

The objective of this work was to investigate the color, transparency, water sensitivity and mechanical properties stability in air under photo-oxidative degradation influencing consumer acceptance and biodegradation behaviors in soil of soy protein isolate (SPI)/poly (vinyl alcohol) (PVA) blend packaging films during 30 days. The results showed that PVA could dilute the yellow color and make the SPI-based films less darkness in application and the transparency of SPI/PVA films at various stages of degradation was improved. The addition of PVA decreased the ability of SPI protein molecules to absorb water and enhanced the mechanical properties of blend films comparing to pure SPI film in 30 days. Aerobic biodegradation of films in soil proved that the PVA compound interacting with protein imposed negative effects on biodegradation of blend films prolonging their decomposing time. The SPI/PVA blend films decomposed into small fragments of less complex molecules along with surface completely digested after 30 days.     

One‐step electrodeposition of amorphous carbon films containing WO3 with high conductivity and good wettability

Tungsten trioxide‐incorporated hydrogenated amorphous carbon (WO₃/a‐C:H) films have been fabricated on a single‐crystal silicon wafer by liquid phase electrodeposition using methanol as carbon source and tungsten carbonyl as incorporated reagent. The morphology, composition and structure of the films have been investigated by SEM, XPS, Raman scattering spectroscopy, Fourier transform infrared spectroscopy (FTIR) and Transmission electron microscope (TEM), respectively. The effects of WO₃ incorporation on the electrical and wetting properties were studied in detail. The characterization results showed that tungsten trioxide nanocrystalline particles with diameters in the range of 10–20 nm were homogenously embedded in the amorphous carbon films. Also, the electrical conductivity and wetting ability of the films were strongly improved due to the contribution of the tungsten trioxide. Copyright © 2010 John Wiley & Sons, Ltd.     

SEM and AES depth profile studies of thin titanium and titanium oxide films covered by nanoscale evaporated Au layers

Thin titanium and titanium oxide films, both covered by ultra-thin gold layers, have been compared with titanium films after analysis, using a combination of SEM and AES. The Ti films were prepared under UHV conditions by evaporation on a glass substrate. The Ti oxide layers were prepared in situ by precisely controlled oxygen sorption at 298 K on Ti film. Both Ti and Ti oxide films were then covered in situ by a very thin Au layer. Analysis was performed in a separate system after long-term exposure of the films to air. SEM analysis revealed a much smaller size grain on the Au coated Ti films than on Ti films not coated with a Au layer. The thin gold layers covering the Ti surface prevent an extensive air interaction with Ti film. The analysis of the features of the Ti Auger spectra during the sputter profile measurements allow to characterise the chemical nature of Ti-oxide formed in Ti/Au interface region. Received: 7 September 1998 / Revised: 14 January 1999 / Accepted: 2 February 1999     

Liquid phase deposition synthesis of hexagonal molybdenum trioxide thin films

Hexagonal molybdenum trioxide thin films with good crystallinity and high purity have been fabricated by the liquid phase deposition (LPD) technique using molybdic acid (H₂MoO₄) dissolved in 2.82% hydrofluoric acid (HF) and H₃BO₃ as precursors. The crystal was found to belong to a hexagonal hydrate system MoO₃.nH₂O (n~0.56). The unit cell lattice parameters are a=10.651 Å, c=3.725 Å and V=365.997 Å³. Scanning electron microscope (SEM) images of the as-deposited samples showed well-shaped hexagonal rods nuclei that grew and where the amount increased with increase in reaction time. X-ray photon electron spectroscopy (XPS) spectra showed a Gaussian shape of the doublet of Mo 3d core level, indicating the presence of Mo⁶⁺ oxidation state in the deposited films. The deposited films exhibited an electrochromic behavior by lithium intercalation and deintercalation, which resulted in coloration and bleaching of the film. Upon dehydration at about 450 °C, the hexagonal MoO₃.nH₂O was transformed into the thermodynamically stable orthorhombic phase.     

阳极氧化膜WO3（Ⅰ）：电显色和自褪色

用循环伏安法、交流阻抗技术和光电流谱技术研究了阳极氧化膜WO_3电显色和自褪色过程的机理,电显色时,氢原子先在WO_3表面吸附,其后从WO_3表面向晶格内部传输,电褪色时,H_xWO_3晶格中填隙H原子先传输到W表面脱附生成填隙H~+,然后再在电场驱动下在膜中迁移,自褪色过程可能是由膜中所含的少量水和部分填隙H原子的羟基化作用引起的。