Plasma Treatment of Glass Surfaces Using Diffuse Coplanar Surface Barrier Discharge in Ambient Air

We report a study on the treatment of flat glass surfaces by ambient air atmospheric pressure plasma, generated by a dielectric barrier discharge of coplanar arrangement of the electrode system—the diffuse coplanar surface barrier discharge (DCSBD). The plasma treatment of glass was performed in both static and dynamic modes. With respect to wettability of the glass surface, treatment in static mode resulted in non-uniform surface properties, whereas dynamic mode provided a fully uniform treatment. A water contact angle measurement was used to determine the efficiency of plasma treatments in dynamic mode and also to investigate a hydrophobic recovery of plasma treated glass surfaces. The X-ray photoelectron spectroscopy measurements showed a decrease of overall carbon concentrations after plasma treatment. A deconvolution of C1s peak, showed that a short plasma treatment led to decrease of C–C bonds concentration and increases of C–O and O–C=O bond concentrations. An enhancing influence of the glass surface itself on DCSBD diffuse plasma was observed and explained by different discharge onsets and changes in the electric field distribution.     

Surface modification of polyester by oxygen‐ and nitrogen‐plasma treatment

In this paper, we present a study on the surface modification of polyethyleneterephthalate (PET) polymer by plasma treatment. The samples were treated by nitrogen and oxygen plasma for different time periods between 3 and 90 s. The plasma was created by a radio frequency (RF) generator. The gas pressure was fixed at 75 Pa and the discharge power was set to 200 W. The samples were treated in the glow region, where the electrons temperature was about 4 eV, the positive ions density was about 2 × 10¹⁵ m^?3, and the neutral atom density was about 4 × 10²¹ m^?3 for oxygen and 1 × 10²¹ m^?3 for nitrogen. The changes in surface morphology were observed by using atomic force microscopy (AFM). Surface wettability was determined by water contact angle measurements while the chemical composition of the surface was analyzed using XPS. The stability of functional groups on the polymer surface treated with plasma was monitored by XPS and wettability measurements in different time intervals. The oxygen‐plasma‐treated samples showed much more pronounced changes in the surface topography compared to those treated by nitrogen plasma. The contact angle of a water drop decreased from 75° for the untreated sample to 20° for oxygen and 25° for nitrogen‐plasma‐treated samples for 3 s. It kept decreasing with treatment time for both plasmas and reached about 10° for nitrogen plasma after 1 min of plasma treatment. For oxygen plasma, however, the contact angle kept decreasing even after a minute of plasma treatment and eventually fell below a few degrees. We found that the water contact angle increased linearly with the O/C ratio or N/C ratio in the case of oxygen or nitrogen plasma, respectively. Ageing effects of the plasma‐treated surface were more pronounced in the first 3 days; however, the surface hydrophilicity was rather stable later. Copyright © 2008 John Wiley & Sons, Ltd.     

Degradation of Organic Pollutants Using Atmospheric Pressure Glow Discharge Plasma

A method of plasma treatment in which a glow discharge was generated in the small gas gap between an electrode and a water surface was designed and employed in this study. By using this method, many active species were generated on the wastewater surface to degrade organic pollutants. The electric field distribution of the designed electrode model was simulated using the MAXWELL 3D^® simulation software, and the discharge parameters were measured to investigate the impact of design optimization. In addition, we designed an equipotential multi-electrode configuration to treat a methyl orange solution and an azobenzene solution. The experimental and simulation results indicate that the designed electrodes can realize glow discharge with a relatively low voltage and that the generated plasma covers a large area and is in a stable state. Accordingly, the method helped reduce the cost of the reactor and improved the effectiveness of wastewater treatment.     

Effect of surface modification of zinc oxide on the electrochemical performances of [Ni4Al(OH)10]OH electrode

Surface modification of zinc oxide on the [Ni₄Al(OH)₁₀]OH has been performed by a chemical surface precipitation method. Inductively coupled plasma measurements show that the amount of ZnO of prepared samples increases with the increase of initial concentration of Zn²⁺ in the mother solution. Powder X-ray diffraction measurements and scanning electron microscope images show that the modification of ZnO has little effects on the lattice parameters and the particle sizes of the [Ni₄Al(OH)₁₀]OH, but does change the morphology. The charge–discharge cycles results show that the deterioration rate of discharge capacity for the electrode with ZnO is only 4.0 % after 255 cycles, which is lower than that of electrode without ZnO (8.5 %); meanwhile, the maximal numbers of exchanged electrons per nickel atom for the electrodes with ZnO are basically over 1.83, which are higher than that of the electrode without ZnO (1.73), indicating that the modification of ZnO can improve the utilization of active material. In addition, the cyclic voltammogram tests results show that the modification of ZnO not only improves electrochemical cyclic reversibility but also elevates the oxygen evolution potential. Electrochemical impedance spectroscopy measurements show that the modification of ZnO can lower the double layer capacitance and the charge transfer resistance.     

Microcorona Discharge-Mediated Nonthermal Atmospheric Plasma for Seed Surface Modification

By exploiting the physical effect of a highly nonuniform localized electric field and electron-initiated impact ionization on space charge, we generated homogeneous nonthermal plasma under ambient atmosphere. We evaluated the physical characteristics and evolution of microcorona discharge-induced nonthermal atmospheric plasma (NAP) based on a point-to-plane electrode in open air with two distinct configurations. High-voltage pulses were employed as the primary power source of corona discharge generation to reveal the fundamental mechanism, polarity effect and feasibility of using NAP for organic surface modification. Consequently, we employed NAP to modify the surface of rice (Oryza sativa L.) seeds to improve their wettability. The surface modification of the rice seeds was investigated via water apparent contact angle (ACA) and water imbibition (WI) measurements. The ACA and WI measurements revealed not only the improvement in the wetting properties but also the mutual relationships between and limitations of ACA and WI analysis. We found that the WI time reached saturation after a certain treatment time, called the threshold treatment time. Because vacuum conditions are not required, well-established NAP technology will garner interest in many fields, ranging from the life, environmental, and biomedical sciences to solid-state electronics applications.     

Polythiophene-coated nano-silicon composite anodes with enhanced performance for lithium-ion batteries

Herein, a new polythiophene-coated silicon composite anode material was prepared by in situ chemical oxidation polymerization method. The structure of this material was characterized by infrared spectroscopy, which proved that the oxidative polymerization of thiophene occurred mainly in α position. The polythiophene can provide the better electric contact between silicon particles. Therefore, the as-prepared Si/polythiophene composite electrodes achieve better cycling performance than the bare Si anode. The specific capacity of the composite electrode retains 478 mA h g^?1 after 50 cycles.     

Corona Discharge Ionization Source for a Planar High-Field Asymmetric Waveform Ion Mobility Spectrometer

A corona discharge (CD) ionization source was prepared for a planar high-field asymmetric waveform ion mobility spectrometer (FAIMS). The effects of discharge current and discharge distance on ionization efficiency were investigated; and the electric field dependence of the ion injection in the reaction region was studied. The results showed that the discharge current of CD source had good linearity with the intensity of reactant ion peak (RIP), and the RIP intensity increased to a stable level at the discharge distance of >5 mm. An injection electrode was introduced to improve the ionization efficiency. A square-wave voltage applied to the electrode was found to provide optimal performance of ion injection and utilization. The operating parameters of the CD-FAIMS were optimized to achieve trace level detection of dimethyl methylphosphonate (DMMP) sample. The detection limit for DMMP was 0.5 µg/m^3.     

Understanding the flowing atmospheric-pressure afterglow (FAPA) ambient ionization source through optical means

The advent of ambient desorption/ionization mass spectrometry (ADI-MS) has led to the development of a large number of atmospheric-pressure ionization sources. The largest group of such sources is based on electrical discharges; yet, the desorption and ionization processes that they employ remain largely uncharacterized. Here, the atmospheric-pressure glow discharge (APGD) and afterglow of a helium flowing atmospheric-pressure afterglow (FAPA) ionization source were examined by optical emission spectroscopy. Spatial emission profiles of species created in the APGD and afterglow were recorded under a variety of operating conditions, including discharge current, electrode polarity, and plasma-gas flow rate. From these studies, it was found that an appreciable amount of atmospheric H₂O vapor, N₂, and O₂ diffuses through the hole in the plate electrode into the discharge to become a major source of reagent ions in ADI-MS analyses. Spatially resolved plasma parameters, such as OH rotational temperature (T_rot) and electron number density (n_e), were also measured in the APGD. Maximum values for T_rot and n_e were found to be ~1100 K and ~4 × 10¹⁹ m^–3, respectively, and were both located at the pin cathode. In the afterglow, rotational temperatures from OH and N₂⁺ yielded drastically different values, with OH temperatures matching those obtained from infrared thermography measurements. The higher N₂⁺ temperature is believed to be caused by charge-transfer ionization of N₂ by He₂⁺. These findings are discussed in the context of previously reported ADI-MS analyses with the FAPA source.     

Inactivation of Bacteria in Oil Field Injection Water by Non-thermal Plasma Treatment

Microbial pollution commonly causes serious pipe corrosion in oil field injection water system. This paper reports on the application of non-thermal plasma to inactivate bacteria in oil filed injection water. As an efficient inactivation technology, pulsed streamer discharge plasma method injects energy into solution through a plasma channel formed by discharge between electrodes and produces various active species in solution with physical effects (electric field, UV etc.) occurring. Saprophytic bacteria, iron bacteria and sulfate reducing bacteria are used as target. The effects of various gases bubbling (oxygen, nitrogen and air) as well as aeration intensity are investigated. Experimental results show that the inactivation efficiency is greatly enhanced by gas bubbling. After 150 s discharge with oxygen bubbling (667 m³ (m³ h)^?1), the inactivation efficiencies of saprophytic bacteria, iron bacteria and sulfate reducing bacteria achieve 1.85, 4.51 and 5.70 log reduction, respectively. The possible mechanism of bacteria inactivation is also discussed.     

Biaxially Oriented Polypropylene (BOPP) Surface Modification by Nitrogen Atmospheric Pressure Glow Discharge (APGD) and by Air Corona

We compare two surface treatments of biaxially-oriented polypropylene (BOPP), which are carried out in the same dielectric barrier discharge (DBD) apparatus, namely air corona, and N₂ atmospheric pressure glow discharge (APGD). Changes in the surface energy and chemistry are investigated by contact angle measurements, by X-ray photoelectron spectroscopy (XPS) and by attenuated total reflectance infrared spectroscopy (ATR-FTIR). It is shown that N₂ APGD treatment leads to a higher surface energy than air corona treatment, and to the formation of mostly amine, amide, and hydroxyl functional groups at the polypropylene surface. Finally, hydrophobic recovery of the treated film is studied; for both treatment types, the increased surface energy is found to decay in a similar manner with increasing storage time after treatment.     

Graphitized carbon from wastepaper as electrodes for high-performance electric double-layer capacitors

Graphitized carbon electrode material was prepared from wastepaper by graphitization in molten sodium metal. X-ray diffraction and Raman spectroscopy were used to investigate the structural change of resulted carbons, both of which well proved the formation of graphite structure. Graphitized carbons have surface area that is nearly 26 times larger than initial carbonized paper and exhibit better electrochemical performances. The electrochemical performances of graphitized carbons were investigated by cyclic voltammetry, electrochemical impedance spectroscopy, and galvanostatic charge–discharge methods. The cyclic voltammetry results show a maximum specific capacitance of 194 F g^?1. Therefore, wastepaper can be a promising electrode material for high-performance electric double-layer capacitors (EDLCs).     

Generation of Antimicrobial NO<Subscript>x</Subscript> by Atmospheric Air Transient Spark Discharge

Atmospheric pressure air plasma discharges generate potential antimicrobial agents, such as nitrogen oxides and ozone. Generation of nitrogen oxides was studied in a DC-driven self-pulsing (1–10 kHz) transient spark (TS) discharge. The precursors of NO_x production and the TS characteristics were studied by nanosecond time-resolved optical diagnostics: a photomultiplier module and a spectrometer coupled with fast intensified camera. Thanks to the short (~10–100 ns) high current (>1 A) spark current pulses, highly reactive non-equilibrium plasma is generated. Ozone was not detectable in the TS, probably due to higher gas temperature after the short spark current pulses, but the NO_x production rate of ~7 × 10¹⁶ molecules/J was achieved. The NO₂/NO ratio decreased with increasing TS repetition frequency, which is related to the complex frequency-dependent discharge properties and thus changing NO₂/NO generating mechanisms. Further optimization of NO₂ and NO production to improve the biomedical and antimicrobial effects is possible by modifying the electric circuit generating the TS discharge.     

Highly stable asymmetric supercapacitors based on Ni(OH)<Subscript>2</Subscript> deposited on electro-etched carbon paper

Herein, we introduce the application of nickel hydroxide nanosheets on the electro-etched carbon fiber (ECF) formed via a direct electrodeposition, for fabrication of asymmetric supercapacitor. To confirm the practical applicability of prepared Ni(OH)₂–ECF, an asymmetric device was assembled using Ni(OH)₂–ECF in combination with an activated carbon (AC) electrode. Our results showed a substantial cycling stability (96% capacitance retention after 10000 cycles) and considerable rate capability at large discharge currents (60% capacitance retention at 8 A g^??1) for this asymmetric supercapacitor that may have originated from the good contact between Ni(OH)₂ and ECF. A maximum specific capacitance of 88.1 F g^??1 was achieved for Ni(OH)₂–ECF//AC/CF device and showed considerable rate capability at large discharge currents (60% capacitance retention at 8 A g^??1). The results of this study suggest the Ni(OH)₂–ECF electrode is an excellent material for fabrication of supercapacitor electrodes.     

Defluorination and Mineralization of Difluorophenols in Water by Anodic Contact Glow Discharge Electrolysis

Anodic contact glow discharge electrolysis (CGDE) is a DC-excited atmospheric pressure discharge, in which a steady non-thermal plasma is generated locally between the surface of an electrolytic solution and an anode in contact with it. The I–U characteristics of CGDE were investigated. The plasma temperatures were estimated to be in the range, 1373–2045 K. Hydroxyl radicals and hydrogen peroxide were the main oxidants generated by CGDE. The hydrogen peroxide concentration reached 31.2 mmol/L (mM) in a phosphate buffer solution without organic substrates. During CGDE, the DFPs and the corresponding total organic carbon (TOC) in water were consumed. Most of the fluorine atoms in the DFPs were converted to fluoride ions, and the fluoride concentration increased steadily. An analysis of the hydroxylation of DFPs suggested that the hydroxyl radicals generated by CGDE were the key species responsible for the degradation of DFPs, and the possible mechanistic routes of the mineralization of DFPs are proposed. The disappearance of DFPs and the TOC as well as the defluorination of the DFPs followed first-order kinetics. The rate of TOC disappearance was relatively constant: 1.00 ± 0.05 × 10^?2 min^?1. The order of disappearance of the DFPs was 2,6-DFP > 2,3-DFP > 2,5-DFP > 2,4-DFP > 3,4-DFP > 3,5-DFP. In contrast, the order of defluorination of the DFPs was 2,5-DFP > 2,3-DFP > 2,6-DFP > 2,4-DFP > 3,4-DFP > 3,5-DFP. Overall, the order of the reaction rates for each DFP was k_DFP > k_dF > k_TOC.     

Electrochemical characteristics and interfacial contact resistance of Ni-P/TiN/PTFE coatings on Ti bipolar plates

The Ni-P/TiN/PTFE (poly tetra fluoroethylene) composite coatings were prepared by electroless plating method on Ti plate, which was used as bipolar plates of proton exchange membrane fuel cells (PEMFCs). The morphology, crystallographic texture, electrochemical corrosion, contact resistance, and hydrophobic property of the Ti bipolar plates with coatings were investigated. The results revealed that Ni-P/TiN/PTFE coating had a dense surface morphology, uniform distribution of composite particles. Ti with coating showed 0.48 μA cm² of corrosion current in the simulated solution of PEMFCs and 6 mΩ cm² of interfacial contact resistance (ICR). The hydrophobicity test showed that the coating interface was flat and the wetting angle was 112.4°. In conclusion, The Ni-P/TiN/PTFE composite coatings exhibit superior improvement in corrosion resistance, interface hydrophobicity, and conductivity to Ni-P, Ni-P/TiN, and Ni-P/PTFE coatings. The Ni-P/TiN/PTFE coating was suited for bipolar plate surface modification of bipolar plates.     

Polymer matrix of polyethylene porous films functionalized by electrical discharge plasma

The polyethylene porous films were treated by dielectric surface barrier discharge (DSBD) plasma at atmospheric pressure in oxygen (O₂) or nitrogen (N₂), and by radio-frequency discharge (RFD) plasma in air at reduced pressure 46 Pa. The surface energy of films was carried out by direct measurements of contact angles of six testing liquids. The strength of adhesive joints in the system modified polyethylene porous films - polyacrylate was measured by peeling of the joints under the angle of 90°. The significant increase of the surface energy and its polar component of polyethylene porous films modified by all types of plasma were observed. The higher strengths of adhesive joints were found for modification of polyethylene porous films by radio-frequency discharge plasma in comparison with modification of the films by barrier discharge plasma.     

A novel method of preparing of glass capillary columns: Low-temperature plasma etching and polymerization

A novel method is described for the preparation of stable glass capillary columns (glass open tubular columns), including the etching and formation of a polymer film on the inner glass capillary surfaces. The approach used here is based on low-temperature plasma etching and polymerization. Under the influence of a field of radio frequency discharge, low pressure gases of fluoric compounds, introduced into the glass capillary tube, generate excited fluorine radicals which etch the inner surface. The plasma of organosilicone monomer in the glass capillary yields a uniform polymerized film on the inner surface. The resultant material functions as a good stationary phase for glass capillary gas chromatography (GC²). The inner surfaces treated with such a plasma, can be studied by means of a scanning electron microscope (SEM). The flexibility of this method permits the use of various stationary phases and surface modification.     

Polymer template-assisted microemulsion synthesis of large surface area, porous Li2MnO3 and its characterization as a positive electrode material of Li-ion cells

Lithium-rich manganese oxide (Li₂MnO₃) is prepared by reverse microemulsion method employing Pluronic acid (P123) as a soft template and studied as a positive electrode material. The as-prepared sample possesses good crystalline structure with a broadly distributed mesoporosity but low surface area. As expected, cyclic voltammetry and charge–discharge data indicate poor electrochemical activity. However, the sample gains surface area with narrowly distributed mesoporosity and also electrochemical activity after treating in 4 M H₂SO₄. A discharge capacity of about 160 mAh g^?1 is obtained. When the acid-treated sample is heated at 300 °C, the resulting porous sample with a large surface area and dual porosity provides a discharge capacity of 240 mAh g^?1. The rate capability study suggests that the sample provides about 150 mAh g^?1 at a specific discharge current of 1.25 A g^?1. Although the cycling stability is poor, the high rate capability is attributed to porous nature of the material.     

Single-walled Carbon Nanotubes as Electrode Materials for Supercapacitors

Large-scale synthesized single-walled carbon nanotubes （SWNT） prepared by electric arc discharge method and a mixture of NiO and Y2O3 as catalyst have been used as electrode materials for supercapacitors. N2 adsorption/desorption measurement shows that the SWNT is a microporous and mesoporous material with specific surface area 435 m^2·g^-1. The specific capacitance of the nitric acid treated SWNT in aqueous electrolyte reaches as high as 105 F/g, which is a combination of electric double layer capacitance and pseudocapacitance. The SWNT-based capacitors also have good charge/discharge reversibility and cycling perdurability.     

Nano MgFe2O4 synthesized by sol–gel auto-combustion method as anode materials for lithium ion batteries

In this work, spinel structure MgFe₂O₄ nano-crystals were synthesized by sol–gel auto-combustion method. Morphology and structure of the synthesized MgFe₂O₄ material is characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). And its electrochemical properties were investigated at different active material ratio. Galvanostatic charge/discharge and cyclic voltammograms (CVs) measurements show that the electrode with a ratio of 40:40:20, which is the ratio of active material: super-P carbon (SP): polyvinylidene fluoride (PVDF), presents relatively superior performance with the initial discharge capacity of 1,123 mAh g^?1 and charge/discharge efficiency of 96.7 %. And after 50 cycles, it still maintains at 635 mAh g^?1, which is nearly double that of the other two electrodes with active material ratio of 60:25:15 and 80:15:5. Electrochemical impedance spectra testing shows that the charge transfer resistance (Rct) decreases along with the increasing amount of SP, which is benefit for reducing the polarization and improving the cycling stability of the electrode to a certain extent.