Effect of TiO<Subscript>2</Subscript> on Various Regions of Active Electrode on Surface Dielectric Barrier Discharge in Air

For surface dielectric barrier discharge in air, we examined the effect of titanium dioxide on various regions of the active electrode on the electrical parameters of discharge, on its emission spectra, and for demonstration of the obtained results also on the concentration of ozone produced by the discharge. We used the active electrode in the form of nine interconnected parallel strips and a square counter electrode. The TiO₂ layer covered either only the strips, the region between the strips, or all active electrode. As reference discharge we used the discharge without any layer of TiO₂. We found that direct application potential has a version when the strips of the active electrode are covered with a layer of TiO_2, because the concentration of ozone produced by the discharge is the highest in all investigated cases. This finding could therefore be used for construction of more efficient ozone generators.     

Photo-Induced Hydrophilicity of TiO<Subscript>2</Subscript> Films Deposited on Stainless Steel via Sol-Gel Technique

The photo-induced hydrophilicity of TiO₂ films deposited on stainless steel substrates and silicon wafers using two different sol-gel routes has been investigated. The results indicate that crystalline titanium oxide films with excellent hydrophilic properties can be obtained on silicon wafer with both routes. XPS and XRD data reveal that films deposited on stainless steel exhibit crystallization features similar to those of films deposited on silicon wafers, and only differ by their oxidation degree owing to a TiO₂ reduction process associated to a diffusion of iron ions during deposition of the acidic sol and/or high temperature post-treatment. Consequently, hydrophilic properties of films deposited on stainless steel are inhibited. The deposition of a SiO_x barrier layer at the film/substrate interface allows preventing such a detrimental substrate influence. A low temperature deposition route of the TiO₂ film associated to the presence of a barrier layer yields best results in preventing iron contamination of the films.     

Comparative Actions of NiO and TiO<Subscript>2</Subscript> Catalysts on the Destruction of Phenol and its Derivatives in a Dielectric Barrier Discharge

This study examined processes of decomposing phenol and its derivatives (resorcin, pyrocatechol and hydroquinone) in aqueous solutions under the action of an atmospheric pressure oxygen dielectric barrier discharge in the presence or absence of catalysts in the plasma zone. Two types of catalysts were tested, NiO and TiO₂. It was found that both materials exhibited catalytic properties. The action of NiO accelerated the step of phenol destruction while the action of TiO₂ catalyst resulted in a more preferable composition of decomposition products and provided a higher degree of carboxylic acid conversion into carbon dioxide than the NiO catalyst.     

Influence of ThO<Subscript>2</Subscript> on the photocatalytic activity of TiO<Subscript>2</Subscript>

Microcomposites consisting of TiO₂ (or Ce-doped TiO₂) and ThO₂ (0.5–2% of the TiO₂ mass) are produced by sol-gel synthesis of TiO₂ in presence of ThO₂. X-ray diffraction study reveals the effects of ThO₂ (compared to the ThO₂-free TiO₂, obtained by the same method) on the anatase interplanar distances, crystallites size and phase composition. The photocatalytic tests in presence of the composites under UV irradiation reveal an increase of the Malachite Green degradation rate constant. The effect depends on the Th relative content, temperature of annealing of the catalyst and addition of other doping agent. The highest photocatalytic activity is observed for TiO₂ obtained at 550°C and containing 1% ThO₂. The composite exhibits activity in dark, also. The presence of Ce⁴⁺ ions is not an obligatory requirement for the realization of the ThO₂ effect. The reported results suggest that the radioactivity of the Th and/or its decay products is one of the main factors responsible for the increased photocatalytic activity of TiO₂.      

Dielectric properties and I-V characteristics of (Pb<Subscript>0.4</Subscript>Sr<Subscript>0.6</Subscript>)TiO<Subscript>3</Subscript> thin films improved by TiO<Subscript>2</Subscript> buffer layers

A TiO₂ thin buffer layer was introduced between the (Pb_0.4Sr_0.6)TiO₃ (PST) film and the Pt/Ti/SiO₂/Si substrate in an attempt to improve their electrical properties. Both TiO₂ and PST layers were prepared by a chemical solution deposition method. It was found that the TiO₂ buffer layer increased the (100)/(001) preferred orientation of PST and decreased the surface roughness of the films, leading to an enhancement in electrical properties including an increase in dielectric constant and in its tunability by DC voltage, as well as a decrease in dielectric loss and leakage current density. At an optimized thickness of the TiO₂ buffer layer deposited using 0.02 mol/l TiO₂ sol, the 330-nm-thick PST films had a dielectric constant, loss and tunability of 1126, 0.044 and 60.7% at 10 kHz, respectively, while the leakage current density was 1.95 × 10⁻⁶ A/cm² at 100 kV/cm.     

Diagnostics of Plasma Behavior and TiO<Subscript>2</Subscript> Properties Based on DBD/TiO<Subscript>2</Subscript> Hybrid System

Plasma catalysis is gaining increasing interest in environmental and energy applications, such as the destruction of gas pollutants and hydrocarbon conversion. In order to further improve the application of plasma catalysis, it is crucial to understand the fundamental mechanisms, especially the mutual interaction between plasma and catalyst. In this paper, a parallel-plate dielectric barrier discharge (DBD) reactor is developed to investigate the plasma behavior and TiO₂ properties in the plasma/catalytic hybrid system. The introduction of TiO₂ thin film coated on the dielectric improves the discharge intensity, which significantly contributes to the enhancement of reactive species and charges. The energy efficiency of generating ozone in DBD/TiO₂ system has been approximately raised by 38% compared to pure DBD when the applied voltage reaches 13 kV. It is fortunately found that the discharge does not change the crystal structure of the TiO₂, but the band gap increases from 3.13 to 3.39 eV, which has been proved to enhance the oxidizability of TiO₂ in the degradation of methyl orange experiment under UV light. The FTIR and XPS spectra also demonstrate that N element is doped into the structure of TiO₂. These results successfully illustrate the plasma behavior and catalyst properties in plasma/catalysis hybrid system and provide reference for the optimization of the plasma catalysis process.     

Nanosized TiO<Subscript>2</Subscript> particles decorated on SiO<Subscript>2</Subscript> spheres (TiO<Subscript>2</Subscript>/SiO<Subscript>2</Subscript>): synthesis and photocatalytic activities

Nanosized TiO₂ and nano-anatase TiO₂ decorated on SiO₂ spherical core shells were synthesized by using a sol–gel method. The synthesized pure TiO₂ nano particle and TiO₂ grafted on SiO₂ sphere with various ratios have been characterized for their structure and morphologies by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectrophotometry (FTIR) and transmission electron microscopy (TEM). Their surface areas were measured using the BET method. The photocatalytic activity of all nanocomposites was investigated using methylene blue as a model pollutant. The synthesized TiO₂/SiO₂ particles appeared to be more efficient in the degradation of methylene blue pollutant, as compared to pure TiO₂ particles.     

Direct Synthesis of Carbon Nanotubes from Only CO<Subscript>2</Subscript> by a Hybrid Reactor of Dielectric Barrier Discharge and Solid Oxide Electrolyser Cell

Synthesis of carbon nanotubes (CNTs) from only carbon dioxide was performed using hybrid reactor of dielectric barrier discharge and solid oxide electrolyser cell (SOEC). The removal of oxygen by SOEC from the plasma region suppresses the regeneration of CO₂ from CO and complete CO₂ conversion was achieved by the hybrid reactor. Co–Mo catalyst supported on a quartz substrate was inserted into the hybrid reactor and aligned CNTs were able to be synthesized on the substrate using only CO₂ as a carbon source.     

Effects of Air/H<Subscript>2</Subscript>O Discharge Plasma on Propane Combustion Enhancement Using Dielectric Barrier Discharges

Combustion provides about 80% energy for our daily life and industrial production. But thermal efficiency of traditional combustion technologies is low, which causes energy waste and serious environmental pollution. In order to improve the combustion efficiency, a combined method based on non-equilibrium plasma generated by dielectric barrier discharge and OH radicals coming from water-steam additive was proposed in this work, and plasma assisted propane combustion was examined and evaluated. The results indicated that when relative humidity (RH) was 20% and applied peak voltage was fixed at 8.75 kV, the relative intensity of OH radical and the flame temperature reached the maximum value at the flame root. At the same time, propane combustion was the most complete. In addition, we found that the erosion of the inner electrode was weakened by H₂O addition, and the symmetry of discharge current was changed from symmetry to asymmetry with the increase of RH. Compared with the pure air undischarged combustion, when the relative humidity was 20% and under the discharge conditions of 8.75 kV, the lean-burn extinction limit was extended to 0.4,which is far lower than the traditional lean-burn limit (0.51).     

Effect of C<Subscript>2</Subscript>H<Subscript>4</Subscript>/N<Subscript>2</Subscript> Ratio in an Atmospheric Pressure Dielectric Barrier Discharge on the Plasma Deposition of Hydrogenated Amorphous Carbon-Nitride Films (a-C:N:H)

The goal of this study was to investigate the properties and growth mechanisms of nitrogen-containing carbon-based coatings obtained with an atmospheric pressure dielectric barrier discharge in an N₂-C₂H₄ atmosphere. Radically different chemical compositions were observed depending on C₂H₄/N₂ ratio. With a low C₂H₄ concentration (<400 ppm) as a function of the residence time in the discharge, two different growth mechanisms were observed consisting of a highly nitrogenated coating (N/C > 0.8) and low hydrogen content. At the short residence time, growth was due to mobile small radicals that procured a smooth yet soluble coating, while at the longer residence time, diffusion-limited aggregation of high sticking N-containing radicals produced a cauliflower-like structure. With a high C₂H₄ concentration (≥2,000 ppm), a polymer-like coating with relatively lower nitrogen content (N/C ~ 0.2) was observed with a cauliflower morphology for the entire coating. Nanoindentation measurements revealed very different physical properties in the two types of coatings.     

Degradation of ofloxacin by UVA-LED/TiO<Subscript>2</Subscript> nanotube arrays photocatalytic fuel cells

The degradation of ofloxacin (OFX) at low concentration in aqueous solution by UVA-LED/TiO₂ nanotube arrays photocatalytic fuel cells (UVA-LED/TiO₂ NTs PFCs) was investigated. TiO₂ nanotube arrays (TiO₂ NTs) photoanode prepared by anodization-constituted anatase–rutile bicrystalline framework. The results indicated that the degradation efficiency of OFX by UVA-LED/TiO₂ NTs PFC was significantly enhanced by 14.3% compared with UVA-LED/TiO₂ NTs photocatalysis. The pH affected the degradation efficiency markedly; the highest degradation efficiency (95.0%) and the pseudo-first-order reaction rate constant k value (0.049 min^?1) were achieved in neutral condition (pH 7.0). The degradation efficiency increased with the increasing concentration of dissolved oxygen (DO) in the UVA-LED/TiO₂ NTs PFC. The main reactive species of OFX degradation are positive holes (h⁺) and superoxide ion radicals (O ₂ ^·? ) in a DO sufficient condition. Furthermore, the possible pathways of OFX degradation were proposed.     

Interactions in the Al<Subscript>2</Subscript>TiO<Subscript>5</Subscript>-Ti<Subscript>2</Subscript>O<Subscript>3</Subscript> System

Interactions in the Al₂TiO₅-Ti₂O₃ system were studied and the regions of existence of Al_2?2xTi _2x ³⁺ Ti⁴⁺O₅ solid solutions with a pseudobrookite structure were determined.     

Photooxidation of Ethylbenzene with TiO<Subscript>2</Subscript> and Metal Coated TiO<Subscript>2</Subscript> and its Kinetics

Summary. Photooxidation of ethylbenzene with oxygen to give ethylbenzene hydroperoxide has been achieved in a stirred photochemical reactor that was cooled by a water system by irradiation with a 400W high-pressure mercury lamp and using TiO₂ powder and metal coated TiO₂. The effects of the amount of copper or silver coated on TiO₂ and of the temperature on the rate of oxidation have been investigated. It is suggested that thermal cleavage of the O–O bond and photochemically generated singlet oxygen should be considered as the initiating step in a radical chain mechanism. An optimum loading of 6% Ag or 4–5% Cu was observed for photooxidation of ethylbenzene.     

TiO<Subscript>2</Subscript>-SiO<Subscript>2</Subscript> binary xerogels: Synthesis and characterization

Silica/titania binary xerogels were prepared by joint hydrolysis of the ingredients. Gels of various compositions were characterized by ¹H NMR spectroscopy, IR spectroscopy, and thermogravimetry. The spectral characteristics of binary systems differ considerably from mere superposition of the spectra of the two constituent compounds and the spectrum of a mechanical mixture. A feasibility was demonstrated for controlling the acid properties of binary oxide gels via varying the component mole ratio.     

TiO<Subscript>2</Subscript>/SiO<Subscript>2</Subscript> hybrid nanomaterials: synthesis and variable UV-blocking properties

Silica and core–shell structured titania/silica (TiO₂/SiO₂) nanoparticles with particles size ranging from tens to hundreds of nanometers were prepared and deposited onto cotton fabric substrates by sol–gel process. The morphologies of the nanoparticles were characterized by field-emission scanning electron microscope (FE-SEM). The photocatalytic decomposition properties as well as UV-blocking properties of the fabrics treated with SiO₂ and TiO₂/SiO₂ nanoparticles were investigated.     

Thermal behavior of Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>/TiO<Subscript>2</Subscript> mesoporous gels

Summary Titania-based photocatalytic materials were prepared by sol-gel method using Fe³⁺ and polyethyleneglycol (PEG₆₀₀) as additives. Thermogravimetry (TG), differential thermal analysis (DTA) and evolved gas analysis (EGA) with MS detection were used to elucidate processes that take place during heating of Fe³⁺ containing titania gels. The microstructure development of the Fe₂O₃/TiO₂ gel samples with and without PEG₆₀₀ admixtures was characterized by emanation thermal analysis (ETA) under in situ heating in air. A mathematical model was used for the evaluation of ETA results. Surface area and porosity measurements of the samples dried at 120&deg;C and the samples preheated for 1 h to 300 and 500&deg;C were compared. From the XRD measurements it was confirmed that the crystallization of anatase took place after thermal heating up to 600&deg;C.     

Compatibility of TiO<Subscript>2</Subscript> with a CaO-CaCl<Subscript>2</Subscript> melt

Interaction of TiO₂ with a CaO-CaCl₂ melt was studied to determine whether electrolytic production of titanium from oxide raw materials is possible.     

Fabrication and characterization of TiO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript> composite nanoparticles and polyurethane/(TiO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript>) nanocomposite films

TiO₂–SiO₂ composite nanoparticles were prepared by a sol–gel process. To obtain the assembly of TiO₂–SiO₂ composite nanoparticles, different molar ratios of Ti/Si were investigated. Polyurethane (PU)/(TiO₂–SiO₂) hybrid films were synthesized using the “grafting from” technique by incorporation of modified TiO₂–SiO₂ composite nanoparticles building blocks into PU matrix. Firstly, 3-aminopropyltriethysilane was employed to encapsulate TiO₂–SiO₂ composite nanoparticles’ surface. Secondly, the PU shell was tethered to the TiO₂–SiO₂ core surface via surface functionalized reaction. The particle size of TiO₂–SiO₂ composite sol was performed on dynamic light scattering, and the microstructure was characterized by X-ray diffraction and Fourier transform infrared. Thermogravimetric analysis and transmission electron microscopy (TEM) employed to study the hybrid films. The average particle size of the TiO₂–SiO₂ composite particles is about 38 nm when the molar ratio of Ti/Si reaches to1:1. The TEM image indicates that TiO₂–SiO₂ composite nanoparticles are well dispersed in the PU matrix.     

Adsorption of NO,NH<Subscript>3</Subscript> and H<Subscript>2</Subscript>O on V<Subscript>2</Subscript>O<Subscript>5</Subscript>/TiO<Subscript>2</Subscript> catalysts

The adsorption of small molecules NO, NH₃ and H₂O on V₂O₅/TiO₂ catalysts is studied with the semiempirical SCF MO method MSINDO as pre-stage for the selective catalytic reduction of NO. The mixed catalyst is represented by hydrogen-terminated cluster models. The local arrangement of the cluster atoms is in accordance with available experimental information. Partial relaxation of cluster atoms near the adsorption sites is taken into account. Calculated adsorption energies are compared with experimental literature data. Rapid convergence of computed properties with cluster size is observed. A possible reaction mechanism for the catalytic reduction of NO with NH₃ and O₂ is outlined.