Destruction Kinetics of 2,4 Dichlorophenol Aqueous Solutions in an Atmospheric Pressure Dielectric Barrier Discharge in Oxygen

The processes of degradation of 2,4-dichlorophenol (2,4-DCP) aqueous solutions under the action of atmospheric pressure of DBD in oxygen were studied. The degradation of 2,4-DCP proceeds efficiently, the degree of decomposition reaching 100%. The degradation kinetics of 2,4-DCP obeys a formal first-order kinetic law on concentration of 2,4-DCP. The effective rate constants depend weakly on the experimental conditions and are equal to ~ 2 s^?1. Based on experimental data, the energy efficiency of 2,4-DCP decomposition was determined to be in the range of 0.039–0.173 molecules per 100 eV depending on the experimental conditions. The composition of the products was studied by gas chromatography, chromatography-mass spectrometry, UV/visible spectroscopy, fluorescent methods and some chemical methods. The main decomposition products present in the solution were found to be carboxylic acids, aldehydes and chloride ions, whereas carbon dioxide and molecular chlorine appear in the gas. The results obtained are compared with similar data from other advanced oxidation processes (AOP’s) methods.     

Synthesis of cubic Ag@AgCl and Ag@AgBr plasmonic photocatalysts and comparison of their photocatalytic activity for degradation of methyl orange and 2,4-dichlorophenol

Uniform cubic Ag@AgCl and Ag@AgBr plasmonic photocatalysts with side length of 0.7 µm were synthesized by a facile green route, in which a controllable double-jet precipitation technique was employed to fabricate homogeneous cubic AgCl and AgBr grains while a photoreduction process was used to produce Ag nanoparticles (NPs) on the surface of AgCl and AgBr grains. The synthesized samples were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) analysis, X-ray photoelectron spectroscopy (XPS), and ultraviolet–visible (UV–Vis) diffuse reflectance spectroscopy (DRS). The photocatalytic activities of Ag@AgCl and Ag@AgBr were compared using degradation of methyl orange (MO) dye and 2,4-dichlorophenol (2,4-DCP) under visible-light irradiation. Ag@AgBr showed higher photocatalytic activity for MO degradation but weaker activity for 2,4-DCP decomposition. Possible degradation mechanisms are proposed to interpret these contrary paradoxical experimental results.     

Highly Sensitive Determination of Butyl Xanthate in Surface and Drinking Water by Headspace Gas Chromatography with Electron Capture Detector

A highly sensitive and convenient method for the determination of butyl xanthate in surface water and drinking water was developed by headspace gas chromatography with electron capture detector (HS–GC–ECD). The analytical method was based on the decomposition of butyl xanthate under an acidic condition, generating carbon disulfide, which could be sensitively detected by gas chromatography with electron capture detector. The signal of CS₂ from the decomposition of potassium butyl xanthate was directly proportional to the concentration of potassium butyl xanthate over the range 0.7–100 ng/mL. The detection limit at a signal-to-noise ratio of three (S/N = 3) for potassium butyl xanthate was 0.3 ng/mL (~1.6 × 10⁻⁹ mol/L), which was more than two orders of magnitude lower than the popular UV methods and close to one order of magnitude lower than the similar headspace gas chromatography–mass spectroscopy method. The relative standard deviation (R.S.D.) within a day and in 3 days for potassium butyl xanthate at both 5 and 50 ng/mL was less than 4.7 %, suggesting good analytical performance of the present method. Good recoveries from 93.3 to 104.7 % were obtained from spiked surface and drinking water samples, indicating that the proposed HS–GC–ECD method was applicable for the quantification of butyl xanthate in surface and drinking water. Compared with other reported methods, the present method is highly sensitive, without sample preparation, and easily extended to the analysis of other xanthates.

     

UV-assisted degradation of propiconazole in a TiO2 aqueous suspension: identification of transformation products and the reaction pathway using GC/MS

Photocatalytic degradation of propiconazole, a triazole pesticide, in the presence of titanium dioxide (TiO₂) under ultraviolet (UV) illumination was performed in a batch type photocatalytic reactor. A full factorial experimental design technique was used to study the main effects and the interaction effects between operational parameters in the photocatalytic degradation of propiconazole in a batch photo-reactor using the TiO₂ aqueous suspension. The effects of catalyst concentration (0.15–0.4 gL^?1), initial pH (3–9), initial concentration (5–35 mg L^?1) and light conditions were optimised at a reaction time duration of 90 min by keeping area/volume ratio constant at 0.919 cm² mL^?1. Photocatalytic oxidation of propiconazole showed 85% degradation and 76.57% mineralisation under UV light (365 nm/30 Wm^?2) at pH 6.5, initial concentration 25 mg L^?1 and constant temperature (25 ± 1 °C). The Langmuir–Hinshelwood kinetic model has successfully elucidated the effects of the initial concentration on the degradation of propiconazole and the data obtained are consistent with the available kinetic parameters. The photocatalytic transformation products of propiconazole were identified by using gas chromatography–mass spectrometry (GC/MS). The pathway of degradation obtained from mass spectral analysis shows the breakdown of transformation products into smaller hydrocarbons (m/z 28 and 39).     

Ion-Pair Single-Drop Microextraction Determinations of Degradation Products of Chemical Warfare Agents in Water

Ion-pair single-drop microextraction (SDME) coupled to gas chromatography–mass spectroscopy (GC–MS) methods for the determination of four degradation products of chemical warfare agents were investigated in water. Acidic analytes were converted into their ion-pair complexes with cation surfactants in aqueous sample and then extracted into the organic single drop containing the derivatising agent. Upon injection, the analytes were derivatised in the GC injection hot port. Parameters, such as type of extraction solvent, ion-pairing (IP) reagent, reagent concentration, salt concentration, stirring speed and pH, were all optimized. This method is reproducible for spiked water sample for four different analytes (RSDs < 9.33 %, n = 5) and linear (r ² > 0.9945). The limit of detection (LOD) is in the range of 0.08–0.01 ng mL^?1 (S/N = 5) under GC–MS selected ion monitoring mode. The method was successfully applied to the proficiency test samples from the Organization for Prohibition of Chemical Weapons (OPCW).     

Development of Immunoaffinity Sample-Purification for GC–MS Analysis of Ractopamine in Swine Tissue

A method combining immunoaffinity chromatography with gas chromatography–mass spectrometry (GC–MS) has been established for determination of ractopamine residues in swine liver and urine. After clean-up on an immunoaffinity chromatography column, GC–MS analysis revealed recovery from blank swine liver and urine fortified at 2.5–20 ng g^?1 (ng mL^?1 for urine), respectively, was 68.2–78.6 and 76.2–83.1%. The limits of detection and quantification were 0.5 ng g^?1 (or ng mL^?1) and 2.0 ng g^?1 (or ng mL^?1), respectively. The procedure was used for analysis of ractopamine residues in samples of swine liver and urine in which the levels were unknown. The amounts detected were 9–216 ng g^?1 (ng mL^?1).     

Quantum dot induced phototransformation of 2,4-dichlorophenol, and its subsequent chemiluminescence reaction

We have studied the CdTe quantum dot-induced phototransformation of 2,4-dichlorophenol (2,4-DCP) and its subsequent chemiluminescence (CL) reaction. Quantum dots (QDs) of different size and capped with thioglycolic acid were prepared and characterized by molecular spectroscopy, X-ray diffraction and transmission electron microscopy. In the presence of QDs, 2,4-DCP is photochemically transformed into a long-living light emitting precursor which can react with N-bromosuccinimide to produce CL with peak wavelengths at 475 and 550 nm. The formation of singlet oxygen during the phototransformation process was confirmed by the enhancement effect of deuterium oxide on the CL reaction and the change in the UV spectrum of a chemical trap. The CL intensity is linearly related to the concentration of 2,4-DCP in the range from 0.36 to 36 μmol L^?1, and the detection limit (at 3σ) is 0.13 μmol L^?1.

Hydrodechlorination of chlorophenols over Pd catalysts supported on zeolite Y,MCM-41 and graphene

Hydrodechlorination (HDC) reaction of chlorophenols was carried out using Pd catalysts supported over zeolite Y, MCM-41 or graphene. Pd-MCM-41 and Pd-Y zeolite were prepared by impregnation and ion-exchange method, respectively. Pd-graphene (Pd-G) was prepared by hydrazine hydrate reduction of palladium ion dispersed on graphene oxide. The catalysts were characterized by several analytical tools such as X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and energy-dispersive X-ray spectroscopy (EDS). These catalysts were subjected to HDC reaction of chlorophenols, such as 4-chlorophenol (4-CP), 2,4-dichlorophenol (2,4-DCP), 2,6-dichlorophenol (2,6-DCP) and 3,4-dichlorophenol (3,4-DCP). The reaction rate of HDC of chlorophenols catalyzed by Pd catalysts with various solid bases, such as KF/Al₂O₃ (alumina), sodium acetate (NaOAc) and K₂CO₃ was compared. First, Pd-MCM-41 and Pd-Y catalysts were compared. 2,4- and 3,4-DCPs were completely decomposed within 6 h, in the case of Pd-MCM-41 with NaOAc. Using Pd-Y instead of Pd-MCM-41 with NaOAc, much faster decomposition was observed. Faster decomposition of 4-CP and DCPs was observed with NaOAc base than K₂CO₃ or KF/Al₂O₃ under the same condition. In the case of Pd-Y with KF/Al₂O₃, slower decomposition of 4-CP and DCPs was observed. These base effects were interpreted using the solubility of NaCl and KCl in alcohol and the basic sites of KF/Al₂O₃. Because the solubility of NaCl is known to be larger than KCl solubility in alcohol, byproduct NaCl could be easily dissolved and ionized in solvents. For Pd-Y with KF/Al₂O₃, the small pore size of Y zeolite can interfere with the diffusion of HCl to KF/Al₂O₃ basic site. Second, three catalysts, including Pd-graphene, were compared. 2,4-DCP was decomposed within 2 h using Pd-G with either K₂CO₃, NaOAc or KF/Al₂O₃. Pd-G catalyst showed the highest catalytic activity among Pd-G, Pd-MCM-41 and Pd-Y catalysts. The high activity and stability of the Pd-G could be attributed to the strong metal–support interaction with an electron-deficient site and a critical Pd particle size (ca. 3.5 nm) of Pd-G nanocatalyst with a stronger resistance to the deactivation and good affinity toward aromatic organic molecules, especially phenols. The progress of HDC reaction was monitored by gas chromatography with flame ionization detection (GC/FID), and a feasible degradation process could be explained by analyzing the degradation products such as phenol, cyclohexanone and cyclohexanol from resulting GC chromatograms. The effect of reaction temperature on HDC in Pd-G catalyst was also discussed. In conclusion, Pd-G is an efficient catalyst for decomposition of chlorophenols and can be applied to remediation of chlorophenol-contaminated water under mild conditions.     

Destruction of 2,4-Dichlorophenol in Water Solution Using a Combined Process of Sorption and Plasma Exposure to DBD

The results of studies of the decomposition of 2,4-dichlorophenol (2,4-DCP) in its aqueous solution under the action of atmospheric pressure DBD in an oxygen flow are presented. A new reactor design was used in which the discharge zone was filled with a sorbent (diatomite). It was found that the kinetics of decomposition obeys a first-order kinetic equation for the concentration of 2,4-DCP. The presence of an adsorbent significantly improves the parameters of the decomposition process. Decomposition rates, rate constants and energy efficiency are doubled. So, at a specific discharge power of 1.8 W/cm³ in the presence of a sorbent, the rate constant was ~1 s^?1, and without it, ~0.5 s^?1. The energy efficiency was 0.031 and 0.016 molecules per 100 eV, respectively. The parameters of the treated solution are improved in terms of its potential toxicity. The concentrations of the main decomposition products (aldehydes, carboxylic acids) in the presence of a sorbent are significantly less than without it. This is due to an increase in the rate of conversion of these products into carbon dioxide molecules. It was also shown that the decomposition of one 2,4-DCP molecule leads to the formation of two chloride ions in solution, and the ozone formed in the discharge does not significantly affect the destruction process.

     

Ion-Pair Single-Drop Microextraction Determinations of Degradation Products of Chemical Warfare Agents in Water

Ion-pair single-drop microextraction (SDME) coupled to gas chromatography–mass spectroscopy (GC–MS) methods for the determination of four degradation products of chemical warfare agents were investigated in water. Acidic analytes were converted into their ion-pair complexes with cation surfactants in aqueous sample and then extracted into the organic single drop containing the derivatising agent. Upon injection, the analytes were derivatised in the GC injection hot port. Parameters, such as type of extraction solvent, ion-pairing (IP) reagent, reagent concentration, salt concentration, stirring speed and pH, were all optimized. This method is reproducible for spiked water sample for four different analytes (RSDs < 9.33 %, n = 5) and linear (r ² > 0.9945). The limit of detection (LOD) is in the range of 0.08–0.01 ng mL⁻¹ (S/N = 5) under GC–MS selected ion monitoring mode. The method was successfully applied to the proficiency test samples from the Organization for Prohibition of Chemical Weapons (OPCW).

     

Simultaneous Analysis of Hexaconazole, Myclobutanil, and Tebuconazole Residues in Apples and Soil by SPE Clean-Up and GC with Nitrogen–Phosphorus Detection

A facile and sensitive method utilizing capillary gas chromatography with nitrogen phosphorus detection (GC–NPD) has been developed and validated for simultaneous analysis of hexaconazole, myclobutanil, and tebuconazole, three broad-spectrum systemic fungicides, in apples and soil. Two samples were fortified with the three pesticides and subjected to ultrasonic extraction, followed by solid-phase extraction (SPE) to remove coextractives, before analysis by GC–NPD. SPE procedures were performed on PSA cartridges (500 mg, 3 mL), the analytes being eluted with n-hexane–acetone (9:1 v/v, 2 mL). Recovery of three pesticides from the fortified apple and soil samples ranged from 94.5 to 107.3% with relative standard deviations less than 9.7% at the three spike levels (0.01, 0.1, and 0.5 mg kg^?1). Limits of quantification of the method for apple and soil were 0.01 mg kg^?1, sufficiently below the maximum residue limits. Direct confirmation of the analytes in samples was achieved by gas chromatography–mass spectrometry (GC–MS).     

Determination of Aroma Compounds from Alcoholic Beverages in Spiked Blood Samples by Means of Dynamic Headspace GC–MS

Some aroma compounds found in alcoholic beverages are characteristic of a certain beverage (i.e. 2,4-decadienoic acid ethyl ester is characteristic of pear spirit and 5-butyltetrahydro-4-methylfuran-2-on “whiskey lactone” is characteristic of aged spirits like whiskey). These substances were detectable in beverages but not in blood samples. The aim of this investigation was to find a sensitive sampling technique for aroma compounds in whole blood samples. This technique may be used in forensic toxicology for examination of drinking claims. The method comprises dynamic headspace sampling using a purge and trap concentrator, followed by quantitative gas chromatography–mass spectrometry (dynamic HS–GC–MS). The influence of sample preparation, trap adsorbents and sample temperature as well as desorption time and purge time on the quality of the analytical results were investigated. The following optimal parameters were determined: stirred and diluted whole blood sample without salt addition, use of Carbotrap C as trap material, sample temperature at 80 °C, desorption time 20 min and purge time 30 min. These optimal parameters were used for the determination of detection limits (LOD). The LOD of aroma compounds by means of dynamic headspace sampling were compared with the results of conventional sampling: the static headspace technique. Limits of detection for the aroma compounds with conventional static headspace GC are in the range 400–10,000 μg L^?1. Dynamic headspace–GC was found to be a more sensitive sampling technique for most of the aroma compounds investigated (e.g. C₄–C₈ ethyl esters, benzoic acid ethyl ester, linalool oxide and 4-ethylguaiacol) with detection limits between 1 and 50 μg L^?1, but there were also limits to the sampling of substances with lower volatility like decanoic acid ethyl ester, 2,4-decadienoic acid ethyl ester, eugenol and whiskey lactone with detection limits of about 1,000 μg L^?1.     

Aromatic polyamides. II. Thermal degradation of some aromatic polyamides and their model diamides

Thermal degradation behavior of poly(1,3-phenylene isophthalamide) and poly(chloro-2,4-phenylene isophthalamide) was investigated with the aid of some appropriate model compounds. The pyrolysis products of these materials were identified by gas chromatography (GC), gas chromatography/Fourier transform infrared spectroscopy (GC/FT-IR), and gas chromatography/mass spectrometry (GC/MS). The residual chars were characterized by IR spectroscopy. Thermogravimetric analysis (TGA) was applied to study the effect of end-group concentration on the degradation characteristics of the two polyamides. Kinetic parameters that describe the thermal degradation of the polyamides were also evaluated by TGA. The results of this investigation suggest that the thermal decomposition of these aromatic polyamides involves homolytic as well as hydrolytic cleavages of the amide units.     

Validation of an assay for the determination of levoglucosan and associated monosaccharide anhydrides for the quantification of wood smoke in atmospheric aerosol

Biomass burning is becoming an increasing contributor to atmospheric particulate matter, and concern is increasing over the detrimental health effects of inhaling such particles. Levoglucosan and related monosaccharide anhydrides (MAs) can be used as tracers of the contribution of wood burning to total particulate matter. An improved gas chromatography–mass spectrometry method to quantify atmospheric levels of MAs has been developed and, for the first-time, fully validated. The method uses an optimised, low-volume methanol extraction, derivitisation by trimethylsilylation and analysis with high-throughput gas chromatography–mass spectrometry (GC–MS). Recovery of approximately 90 % for levoglucosan, and 70 % for the isomers galactosan and mannosan, was achieved using spiked blank filters estimates. The method was extensively validated to ensure that the precision of the method over five experimental replicates on five repeat experimental occasions was within 15 % for low, mid and high concentrations and accuracy between 85 and 115 %. The lower limit of quantification (LLOQ) was 0.21 and 1.05 ng m^?3 for levoglucosan and galactosan/mannosan, respectively, where the assay satisfied precisions of ≤20 % and accuracies 80–120 %. The limit of detection (LOD) for all analytes was 0.105 ng m^?3. The stability of the MAs, once deposited on aerosol filters, was high over the short term (4 weeks) at room temperature and over longer periods (3 months) when stored at ?20 °C. The method was applied to determine atmospheric levels of MAs at an urban background site in Leicester (UK) for a month. Mean concentrations of levoglucosan over the month of May were 21.4?±?18.3 ng m^?3, 7.5?±?6.1 ng m^?3 mannosan and 1.8?±?1.3 ng m^?3 galactosan. Figure

Monosaccharide anhydride levels and percent contribution to PM₁₀ from filter punches taken every 24 h at an urban background site in Leicester, analysed by GC–MS. G galactosan, M mannosan, L levoglucosan     

Ultrasensitive direct determination of BTEX in polluted soils using a simple and novel pressure-controlled solid-phase microextraction setup

A pressure-controlled headspace solid-phase microextraction (PC-HS-SPME) setup was developed, by reconsidering the strengths and weaknesses points of the similar reported systems. The new setup was coupled with gas chromatography–flame ionization detection (GC–FID) for direct analysis of benzene, toluene, ethylbenzene and xylene (BTEX) in contaminated soils, without any sample preparation step. The important experimental factors, affecting the performance of the method, including volumes of extraction and vacuum vials, type of SPME fiber, extraction time and temperature, moisture content of the sample, and sonication time were studied and optimized. Under the optimal conditions, good linearity of the calibration curves (R² > 0.997) was obtained in the concentration range of 0.1–20,000 ng g^?1. The limits of detections were found to be 0.001–0.08 ng g^?1. The relative standard deviations, for six repetitive analyses of 100 ng g^?1 BTEX, were obtained to be 5.7–12.3%. The PC-HS-SPME–GC–FID procedure was successfully applied for the extraction and determination of BTEX in the polluted soil samples.     

Simple Determination of 4-Methylimidazole in Soft Drinks by Headspace SPME GC–MS

A simple method to detect 4-methylimidazole in soft drinks is described. This method is based on headspace solid-phase micro-extraction and gas chromatography–mass spectrometry (HS-SPME GC–MS). The HS-SPME parameters (selection of fiber, extraction temperature, heating time, and pH) were optimized and selected. Under the established condition, the detection and the quantification limit were 1.9 and 6.0 μg L^?1 using 4 mL of the liquid sample, respectively. The relative standard deviation for five independent determinations at 100.0 and 500.0 μg L^?1 was less than 8 %. The calibration curve was y = 0.6027x–0.0033 with a linearity of r ² = 0.997. Using the proposed method, the levels of 4-MEI were detected in a range from 94.0 to 324.8 μg L^?1. The comparison of liquid chromatography tandem mass spectrometry (LC–MS/MS) with the proposed method was performed and the agreement with LC–MS/MS for all samples was acceptable.     

A Novel Derivatization Method Coupled with GC–MS for the Simultaneous Determination of Chloropropanols

A sensitive and rapid derivatization method for the simultaneous determination of chloropropanols [1,3-dichloropropan-2-ol (1,3-DCP), 2,3-dichloropropan-1-ol (2,3-DCP) and 3-chloropropane-1,2-diol (3-MCPD)] has been developed. The three chloropropanols were silylated with 1-trimethylsilylimidazole and then determined by GC–MS. n-Undecane was used as the internal standard. The limits of detection (LOD) were 0.20, 0.10, 0.14 μg kg^?1 for 1,3-DCP, 2,3-DCP and 3-MCPD, respectively. The three compounds behaved >0.999 of linearity and satisfactory precision with the relative standard deviation (RSD) <10%. The excellent validation data suggested that this method was more effective than heptafluorobutyrylimidazole derivatization, and 1-trimethylsilylimidazole was considered as a promising silylating reagent to be widely applied to measurements of chloropropanols in real samples.     

Analysis of 28 insecticides in curry leaves (Murraya koenigii L.) by gas chromatography and gas chromatography–mass spectrometry

A simple and efficient method was developed for analysis of 28 insecticides (organochlorines, organophosphates and synthetic pyrethroids) in curry leaves (Murraya koenigii L.). The extraction of the analytes was carried out with acidified acetonitrile and purification with magnesium sulphate, primary secondary amine along with graphitised carbon black to remove excess chlorophyll content in curry leaves. Acetonitrile extracts were changed into hexane + acetone (9 + 1) and hexane + toluene (9 + 1) in the final step. In another method ethyl acetate was used for extraction and purification was carried out as above. The analytes in the samples were determined by gas chromatography (GC) and confirmed by gas chromatography–mass spectrometry (GC–MS). Use of ethyl acetate increased the recovery of the analytes, but co-extractive interference led to higher GC maintenance. Acidified acetonitrile was found to be a better extraction solvent compared with ethyl acetate. The use of hexane:toluene (9:1) as exchange solvent increased the recovery of organochlorine insecticides compared with hexane:acetone (9:1). The limit of quantification (LOQ) of the method was 0.01 mg kg^?1 for organochlorine insecticides and 0.05 mg kg^?1 for organophosphates and synthetic pyrethroids. The recoveries of organochlorines were within 70.36–82.45%; organophosphates, 82.54–90.93% and synthetic pyrethroids, 88.45–90.71% at the LOQ level. The method developed was found suitable for analysis of real samples of curry leaves. The pesticides detected in curry leaves collected from the retail market were mainly organophosphates and synthetic pyrethroids.     

Fatty acids profiling of avocado seed and pulp using gas chromatography–mass spectrometry combined with multivariate chemometric techniques

In the present study, the profiling of 17 fatty acids (FAs) in avocado seed and pulp was investigated. The fatty acids were extracted with vortex-assisted extraction, methyl esterified and finally preconcentrated by dispersive liquid–liquid microextraction. The preconcentrated fatty acid methyl esters (FAMEs) were analyzed using gas chromatography–mass spectrometry (GC–MS) to obtain qualitative and quantitative information. The GC–MS data were analyzed using multivariate curve resolution-alternating least squares (MCR-ALS) method to overcome general chromatographic problems such as overlapped peaks, background interference and peak shifts. The calibration data were prepared using pure analytical information obtained by MCR-ALS. The linear dynamic ranges and regression coefficients (R ²) for FAMEs were in the range of 0.19–65 mg L^?1 and 0.990–0.999, respectively. The relative standard deviation (RSD%) for determination of FAs in avocado seed and pulp was 0.17–8.84 and 0.64–17.93, respectively. The main FAs in the avocado pulp were: oleic acid (74.25 g Kg^?1), linoleic acid (26.87 g Kg^?1), palmitic acid (26.02 g Kg^?1), palmitoleic acid (1.22 g Kg^?1) and stearic acid (0.05 g Kg^?1). And, the main FAs in the avocado seed were: linoleic acid (1.09 g Kg^?1), palmitic acid (0.47 g Kg^?1), oleic acid (0.33 g Kg^?1), linolenic acid (0.12 g Kg^?1), and palmitoleic acid (0.04 g Kg^?1).     

Sensitive Analysis of Malondialdehyde in Human Urine by Derivatization with Pentafluorophenylhydrazine then Headspace GC–MS

A sensitive method based on derivatization with pentafluorophenylhydrazine then headspace gas chromatography–mass spectrometry has been used for analysis of malondialdehyde in human urine. Preparation of urine sample by one-step derivatization/evaporation was performed by reaction of malondialdehyde with pentafluorophenylhydrazine in a headspace vial for 10 min; the derivatives were then injected in GC–MS analysis. The reaction was performed at pH 3, and total analysis time was 35 min. The method detection limit was 0.04 μg L^?1. For MDA concentrations of 2.0 and 10.0 μg L^?1 the relative standard deviation was less then 5%. The concentration of MDA in urine was measured to be 0.199 ± 0.252 μmol g^?1 creatinine (0.022 ± 0.028 μmol mmol^?1 creatinine).