Effects of impurities containing phosphorus on the surface properties and catalytic activity of TiO2 nanotube arrays

TiO₂ nanotube arrays were prepared by titanium anodic oxidation with either HF or H₃PO₄/NH₄F aqueous electrolyte solutions. The samples were characterized by means of X-ray diffraction (XRD), infrared spectroscopy (IR), Raman spectroscope, photoluminescence spectra (PL) and photocurrent response. Aqueous solutions of methylene blue or Cr(VI) ions were used as the target pollutants to compare catalytic activities of the two nanotube array types. The amorphous impurities containing phosphorus were confirmed by XRD and IR, for the sample synthesized with H₃PO₄/NH₄F electrolytes. They closed a portion of the active sites, acted as recombination centers of photo-generated charges, and were also involved in the negative reactions of competing photo-generated holes or OH radicals. The TiO₂ nanotube arrays formed in the H₃PO₄/NH₄F electrolytes exhibited a stronger fluorescence spectrum, a weaker photocurrent and a lower catalytic activity than the sample fabricated with HF electrolyte without phosphorus impurities.     

Fabrication of open-ended TiO2 nanotube arrays by anodizing a thermally evaporated Ti/Au bilayer film

Fabrication of TiO₂ nanotube arrays (TNAs) with through-hole morphology is practical significance to enhance the photocatalytic activity of TNAs, as well as expanding their applications. In present work, open-ended TNAs are synthesized on a conductive Au layer by anodizing a thermally evaporated Ti/Au bilayer film. In the anodizing process, the upper Ti layer is transformed into well-aligned TNAs. The barrier layer under the growing TNAs ultimately touches the Au layer and is completely dissolved by the electrochemical etching. In order to avoid the bubble disruption of TNAs caused by the water electrolysis after the Au layer is exposed to the electrolyte, a specific non-aqueous electrolyte is used. The XRD results reveal that the as-formed open-ended TNAs are amorphous and can be transformed into anatase by annealing at 350 °C.     

Highly ordered anodic TiO2 nanotube arrays and their stabilities as photo(electro)catalysts

Highly ordered TiO₂ nanotube arrays with an average diameter of 230 nm, a wall thickness of 30 nm and a length of 1.8 μm were fabricated within a large domain by electrochemically anodizing of a titanium foil in a mixed solution of glycerol and NH₄F aqueous electrolyte. The TiO₂ nanotubes exhibit an anatase structure after annealing at 450 °C in air for 3 h. The direct photolysis (DP), photocatalytic (PC), electrocatalytic (EC) and photoelectrocatalytic (PEC) activities of the TiO₂ nanotube arrays were investigated using methyl orange (MO) as the model pollutant. The degradation of MO in PC process is faster than that in DP process, which confirms the photocatalysis of TiO₂ nanotube arrays. The degradation rate in PEC process is much higher than those in EC and PC processes, which demonstrates the synergetic effect between PC and EC processes. The synergetic factor is 4.1, which suggests that the synergetic effect is strong. Moreover, the stabilities of morphology, structure and photo(electro)catalytic degradation performance of the TiO₂ nanotube arrays were studied in order to evaluate their applicability as photo(electro)catalysts. The photo(electro)catalytic experiments bring neither morphological nor structural modifications to the nanotube arrays. The photo(electro)catalytic degradation rates of the TiO₂ nanotube arrays maintain stable in 10 cycles, which indicates that the TiO₂ nanotube arrays are appropriate to be applied as photo(electro)catalysts.     

Photoelectrochemical property and photocatalytic activity of N-doped TiO2 nanotube arrays

N-doped TiO₂ nanotube arrays (NTN) were prepared by anodization and dip-calcination method. Hydrazine hydrate was used as nitrogen source. The surface morphology of samples was characterized by SEM. It showed that the mean size of inner diameter was 65 nm and wall thickness was 15 nm for NTN. The ordered TiO₂ nanotube arrays on Ti substrate can sustain the impact of doping process and post-heat treatment. The atomic ratio of N/Ti was 8/25, which was calculated by EDX. Photoelectrochemical property of NTN was examined by anodic photocurrent response. Results indicated the photocurrent of NTN was nearly twice as that of non-doped TiO₂ nanotube arrays (TN). Photocatalytic activity of NTN was investigated by degrading dye X-3B under visible light. As a result, 99% of X-3B was decomposed by NTN in 105 min, while that of TN was 59%.     

Synthesis and field emission of diamond-like carbon nanorods on TiO2/Ti nanotube arrays

Highly ordered TiO₂/Ti nanotube arrays were fabricated by anodic oxidation method in 0.5 wt% HF. Using prepared TiO₂/Ti nanotube arrays deposited Ni nanoparticles as substrate, high quality diamond-like carbon nanorods (DLCNRs) were synthesized by a conventional method of chemical vapor deposition at 750 °C in nitrogen atmosphere. DLCNRs were analyzed by filed emission scanning electron microscopy and Raman spectrometer. It is very interesting that DLCNRs possess pagoda shape with the length of 3–10 μm. Raman spectra show two strong peaks about 1332 cm⁻¹ and 1598 cm⁻¹, indicating the formation of diamond-like carbon. The field emission measurements suggest that DLCNRs/TiO₂/Ti has excellent field emission properties, a low turn-on field about 3.0 V/μm, no evident decay at 3.4 mA/cm² in 480 min.     

Fabrication, characterization and photoelectrochemical properties of Fe2O3 modified TiO2 nanotube arrays

TiO₂ nanotube (NT) arrays modified by Fe₂O₃ with high sensibility in the visible spectrum were first prepared by annealing anodic titania NTs pre-loaded with Fe(OH)₃ which was uniformly clung to the titania NTs using sequential chemical bath deposition (S-CBD). The photoelectrochemical performances of the as-prepared composite nanotubes were determined by measuring the photo-generated currents and voltages under illumination of UV-vis light. The titania NTs modified by Fe₂O₃ showed higher photopotential and photocurrent values than those of unmodified titania NTs. The enhanced photoelectrochemical behaviors can be attributed to the modified Fe₂O₃ which increases the probability of charge-carrier separation and extends the range of the TiO₂ photoresponse from ultraviolet (UV) to visible region due to the low band gap of 2.2 eV of Fe₂O₃.     

Optical and electrical characterization of TiO2 nanotube arrays on titanium substrate

Novel oriented aligned TiO₂ nanotube (TN) arrays were fabricated by anodizing titanium foil in 0.5% HF electrolyte solution. It is indicated that the sizes of the TNs greatly depended on the applied voltages to some extent. The electrical properties of the TN arrays were characterized by current-voltage (I-V) measurements. It exhibits a nonlinear, asymmetric I-V characterization, which can be explained that there exists an n-type semiconductor/metal Schottky barrier diode between TN arrays and titanium substrate interface. The absorption edges shift towards shorter wavelengths with the decrease of the anodizing voltages, which is attributed to the quantum size effects. At room temperature, a novel wide PL band consisting of four overlapped peaks was observed in the photoluminescence (PL) measurements of the TN arrays. Such peaks were proposed to be resulted from the direct transition X₁ → X₂/X₁, indirect transition Γ₁ → X₂/X₁, self-trapped excitons and oxygen vacancies, respectively.     

有序TiO2纳米管阵列结构的可控生长及其物相研究

分别在HF水溶液、含NH₄F和H₂O的乙二醇有机溶液中对Ti箔进行阳极氧化,得到TiO₂纳米管阵列结构.该结构高度有序、分布均匀、垂直取向,且通过阳极氧化工艺条件(如阳极氧化电压、电解液的选择与配比以及氧化时间等)可实现对其结构参数(如管径、管壁厚度、管密度、管长等)的有效控制.利用XRD研究了TiO₂纳米管阵列的物相结构.结果表明：退火前的TiO₂纳米管阵列为无定形结构;分别在真空和氧气氛中50 关键词： 2纳米管阵列')" href="#">TiO₂纳米管阵列 阳极氧化 可控生长     

Photoelectrocatalytic degradation of organic contaminants at Bi2O3/TiO2 nanotube array electrode

In the current work, TiO₂ nanotube array was prepared via electrochemical anode method. Then the Bi₂O₃ nanoparticles were deposited onto the TiO₂ nanotube array via dip-coating method from an amorphous complex precursor. The crystal structures were characterized via X-ray diffraction analysis. Their surface textures were observed via electron-scanning microscope. The prepared composite array electrode exhibited high photoelectrocatalytic activities towards degrading organic contaminants under visible light irradiation. High photoelectrocatalytic activities were also exhibited under UV light irradiation. The catalytic mechanism was discussed based on the analysis of electrochemical and degradation kinetics results. It is suggested a P (Bi₂O₃)-N (TiO₂) junction was formed to increase the catalytic activates. The stability of the electrode materials was confirmed finally.     

The effect of pre-pattern on the morphology and growth speed of TiO2 nanotube

In this work, we presented a new method which directly acts on the surface of the Ti sheet by mechanical micro-etching using a grating ruling engine. The effect of the pre-pattern on the morphology and growth speed of TiO₂ nanostructure formed on the Ti sheet with the traditional anodization method was investigated. A novel wall structure was observed and the growth speed of TiO₂ nanotube (NT) was greatly affected by the pre-pattern. The wall structure increases the surface-to-volume ratio of the nanotube arrays. The new method provided the possibility of further optimization of fast growth of TiO₂ nanostructure and improving the efficiency of dye-sensitized solar cell (DSSC) and photocatalysis.     

Effects of coating parameters on the morphology of SiO2-coated TiO2 and the pigmentary properties

SiO₂-coated TiO₂ powders were prepared by the chemical deposition method starting from rutile TiO₂ and Na₂SiO₃. The SiO₂-coated TiO₂ powders were characterized by X-ray photoelectron spectroscopy, Zeta-potential analysis, Fourier transform infrared spectroscopy, and transmission electron microscopy. The evolution of island-like and uniform coating layers was found to depend upon the ratio of Na₂SiO₃ to TiO₂, reaction temperature, and pH. The whiteness and brightness of the SiO₂-coated TiO₂ powders increased in response to an increase in the SiO₂ loading, but there was a maximum value among the light scattering indexes. The SiO₂-coated TiO₂ powders possessed more negative Zeta potentials than the naked TiO₂. The dispersibility of the SiO₂-coated TiO₂ powders with the continuous and uniform SiO₂ coating layers was higher than that of the naked TiO₂ and the SiO₂-coated TiO₂ powders with the island-like SiO₂ coating layers.     

由纳米管和纳米颗粒构成的TiO2膜的制备与机理研究

采用聚苯乙烯小球修饰Ti片表面,并进行阳极氧化,制备出一种由纳米颗粒和纳米管构成的TiO₂膜．通过数值模拟,分析了氧化表面附近的局部电场分布对TiO₂膜形貌的影响．结果表明,覆盖物增强了局部电场,从而加快了O^2-与Ti的反应速率,有利于TiO₂的生长;与此同时,[TiF₆]^6-的扩散受到阻碍,使得TiO₂的溶解速率减慢．可见,覆盖物打破了TiO₂纳米管形成的平衡条件,导致纳米颗粒的生成．此外,通过X射线衍射和Raman光谱的测试分析发现,所制备的TiO₂为锐钛矿结构.     

含水量对TiO2纳米管形貌控制参数的影响

以不同含水量的乙二醇溶液为电解液,采用阳极氧化法制备TiO2纳米管阵列。通过记录反应过程中电导率、粘度及回路电流随时间的变化曲线,研究含水量对电解液粘度、电导率及电流等过程参数的影响,分析了纳米管形貌尺寸与TiO2溶蚀所耗电荷量的关系。粘度初始值和初始电导率均与含水量呈三次关系,相关系数分别为0.992 5和0.977 8。在反应过程中,溶液粘度值有缓慢增加的趋势。由于不同含水量的电解液粘度的不同,H+和OH-数量不同,F-迁移速率不同,电导率-时间曲线及电流-时间曲线具有不同的变化趋势,并对其进行了理论分析。当水体积分数为4%,5%,6%和10%时,纳米管的形貌较为有序并且TiO2纳米管阵列表面的碎片较少,纳米管直径变化范围为50 nm至72 nm,长度变化范围为0.85~1.90 m。F-腐蚀氧化膜时所消耗电量与TiO2氧化膜被腐蚀掉的体积呈一次函数关系,即腐蚀电量越大,腐蚀掉的体积越大,为制备一定形貌尺寸的纳米管提供了一定的控制方法。     

Effect of crystallographic orientation on the anodic formation of nanoscale pores/tubes in TiO2 films

Self-organized nanopores and nanotubes have been produced in thin films of titanium (Ti) prepared using filtered cathodic vacuum arc (FCVA), DC- and RF-sputter deposition systems. The anodization process was performed using a neutral electrolyte containing fluoride ions with an applied potential between 2 and 20 V (for clarity the results are only presented for 5 V). Scanning electron microscopy (SEM), atomic force microscopy (AFM) and X-ray diffraction (XRD) techniques were used to characterise the films. It was found that the crystallographic orientation of the Ti films played a significant role in determining whether pores or tubes were formed during the anodic etching process.     

Enhanced Photoelectrochemical Property of Zn Loaded TiO2 Nanotube Arrays Electrode

采用计时电流法制备了负载Zn纳米粒子的TiO₂纳米管阵列电极．通过阳极氧化法制备TiO₂纳米管阵列电极,然后通过控制计时电流沉积时间来控制负载在TiO₂纳米管上Zn纳米颗粒的沉积量和 沉积尺寸．SEM和XRD分析结果显示,沉积时间为3～5 s时,负载在TiO₂纳米管上的Zn粒子的直径为15～25 nm．UV漫反射光谱发现负载Zn的TiO₂纳米管阵列电极比没有负载的样品吸收487～780 nm的光更强;在高压汞灯照射下,前者比后者的光电流响应提高了50%．     

From anodic TiO2 nanotubes to hexagonally ordered TiO2 nanocolumns

We report on the formation of hexagonally ordered TiO₂ nanocolumnar layers by electrochemical oxidation in a fluoride containing electrolyte, using self-organizing nanotube formation conditions at elevated potentials and low temperatures. The influence of the substrate temperature on the nanocolumn morphology and composition is investigated and characterized by FE-SEM and EDX. The origin of these nanocolumns can be attributed to a thickening of the inner tube wall of the double wall structure of self-organized TiO₂ nanotubes. Furthermore, a transition from nanocolumnar to nanotubular structure can be established by changing the applied voltage or applying a post-immersion treatment.     

Unusual photo-induced adsorption-desorption behavior of propylene on Ag/TiO2 nanotube under visible light irradiation

Titanium dioxide (TiO₂) nanotube with a large amount of single-electron-trapped-oxygen-vacancies (coded as T2) was obtained by annealing nanotube H₂Ti₂O₄(OH)₂ (coded as T1) at 400 °C in air. Silver nanoparticles with a diameter of about 30-50 nm were loaded onto the surface of T2 via deposition associated with photochemical reduction under ultraviolet irradiation. The resulting Ag/TiO₂ nanotube (coded as T3) was characterized by means of transmission electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and ultraviolet-visible light diffusion reflectance spectrometry. It was found that C₃H₆ experienced unusual photo-induced adsorption-desorption on T3 under visible light irradiation. Namely, C₃H₆ was initially desorbed from T3 and then adsorbed on T3 under visible light irradiation. On the contrary, C₃H₆ was initially adsorbed on T3 in the dark, followed by desorption. The reason might lie in that two kinds of active sites exist on the surface of T3, corresponding to quite different rates of adsorption and desorption. It was found that oxygen vacancies in association with deposited silver particles, were responsible for the alternative adsorption-desorption of C₃H₆ on T3.     

Ni-doped TiO2 nanotube arrays on shape memory alloy

Self-organized Ni-Ti-O nanotube arrays were fabricated through a direct anodization of NiTi shape memory alloy in glycerol-based electrolyte. The growth of Ni-doped TiO₂ nanotube arrays was mainly affected by anodization voltage and temperature. Higher anodization voltage facilitated the growth of uniform nanotube arrays. Large-area open-ended Ni-Ti-O nanotube arrays could form on the surface of the shape memory alloy under a higher anodization temperature. The oxide nanotubes had a gradually changed composition along the growth direction of the nanotube and presented a thermal stability up to 400 °C. The nanotubular oxide demonstrated a much better hydrophilic behavior than that of the traditional oxide layer grown on NiTi substrate through air oxidization. The successful fabrication of Ni-doped TiO₂ nanotube arrays here makes it feasible to further explore excellent physical and chemical as well as biomedical properties of the nanotube-modified surfaces of the NiTi shape memory alloy.     

Investigation of chemical decomposition of CCl4 on TiO2 near room temperature

Dissociative adsorption of CCl₄ on TiO₂ at 35 °C has been studied by Fourier-transform infrared spectroscopy, X-ray photoelectron spectroscopy, and electron spin resonance. CCl₄ decompose to form CO, CO₂, and CO₃ on the surface, at such a low temperature, in which CO₂ formation is not from CO oxidation on TiO₂, but CO₃ can be produced by CO and CO₂ adsorption. The Cl generated from CCl₄ decomposition is left on the surface and bonded to titanium ions. Mineralization of CCl₄ on TiO₂ involves the lattice oxygens. Thermodynamical driving force and possible reaction routes for CO and CO₂ formation in the CCl₄ decomposition on TiO₂ are discussed.     

Influence of Au thickness on the optical and electrical properties of transparent and conducting TiO2/Au/TiO2 multilayer films

Au-intermediate TiO₂/Au/TiO₂ (TAT) multilayer films were deposited by RF magnetron sputtering onto glass substrates. Changes in the optical and electrical properties of the films were investigated with respect to the thickness of the Au interlayer.The observed optical and electrical properties were dependent on the thickness of the Au interlayer. The resistivity decreased to 3.3 × 10⁻⁴ Ω cm for TiO₂ films with a 20 nm-thick Au interlayer and the optical transmittance was also influenced by the Au interlayer. Although optical transmittance deteriorated as Au thickness increased, TiO₂ films with a 5 nm-thick Au interlayer showed a relatively high optical transmittance of 80% at a wavelength of 550 nm. In addition, since a TAT film with a 5 nm-thick Au interlayer showed a relatively high work function value, it is an alternative candidate for use as a transparent anode in OLEDs and flat panel displays.