Investigations on structural, vibrational, morphological and optical properties of CdS and CdS/Co films by ultrasonic spray pyrolysis

CdS and CdS/Co films have been deposited on glass substrates by an ultrasonic spray pyrolysis method. The effects of Co incorporation on the structural, optical, morphological, elemental and vibrational properties of these films were investigated. XRD analysis confirmed the hexagonal wurtzite structure of all films and had no impurity phase. While CdS film has (0 0 2) as the preferred orientation, CdS/Co films have (1 1 0) as the preferred orientation. The direct optical band gap was found to decrease from 2.42 to 2.39 eV by Co incorporation. The decrease of the direct energy gaps by increasing Co contents is mainly due to the sp-d exchange interaction between the localized d-electrons of Co²⁺ ions and band electrons of CdS. After the optical investigations, it was seen that the transmittance of CdS films decreased by Co content. The Raman measurements revealed two peaks corresponding to the 1LO and 2LO modes of hexagonal CdS. The vibrational modes of Cd-S were obtained in the wavenumber range (590-715 cm⁻¹) using Fourier transform infrared spectroscopy (FTIR). The elemental analysis of the film was done by energy dispersive X-ray spectrometry.     

Growth and photoluminescence properties of inclined ZnO and ZnCoO thin films on SrTiO_3（110） substrates

ZnO thin film growth prefers different orientations on the etched and unetched SrTiO 3（STO）（110） substrates.Inclined ZnO and cobalt-doped ZnO（ZnCoO） thin films are grown on unetched STO（110） substrates using oxygen plasma assisted molecular beam epitaxy,with the c-axis 42 inclined from the normal STO（110） surface.The growth geometries are ZnCoO[100]//STO[110] and ZnCoO[111]//STO[001].The low temperature photoluminescence spectra of the inclined ZnO and ZnCoO films are dominated by D 0 X emissions associated with A 0 X emissions,and the characteristic emissions for the 2 E（2G）→ 4A2（4F） transition of Co 2＋ dopants and the relevant phonon-participated emissions are observed in the ZnCoO film,indicating the incorporation of Co 2＋ ions at the lattice positions of the Zn 2＋ ions.The c-axis inclined ZnCoO film shows ferromagnetic properties at room temperature.     

Field electron emission from HfNxOy thin films deposited by direct current sputtering

HfN_xO_y thin films were deposited on Si substrates by direct current sputtering at room temperature. The samples were characterized by scanning electron microscopy (SEM), atomic force microscopy (AFM) and X-ray diffraction (XRD). SEM indicates that the film is composed of nanoparticles. AFM indicates that there are no sharp protrusions on the surface of the film. XRD pattern shows that the films are amorphous. The field electron emission properties of the film were also characterized. The turn-on electric field is about 14 V/μm at the current density of 10 μA/cm², and at the electric field of 24 V/μm, the current density is up to 1 mA/cm². The field electron emission mechanism of the HfN_xO_y thin film is also discussed.     

Substrate orientation-induced distinct ferromagnetic moment in Co:ZnO films

Dilute (3.8 at.%) cobalt-doped ZnO thin films are deposited on LiTaO₃ (LT) substrates with three different orientations [LT(1 1 0), LT(0 1 2) and LT(0 1 8)] by direct current reactive magnetron co-sputtering. The experimental results indicate that Co atoms with 2+ chemical valence are successfully incorporated into the ZnO host matrix on various oriented substrates, and the substrate orientations have a profound influence on the crystal growth and magnetization of Co:ZnO films. A large magnetic moment of 2.42μ_B/Co at room temperature is obtained in the film deposited on LT(0 1 2), while the corresponding values of the other films deposited on LT(1 1 0) and LT(0 1 8) are 1.21μ_B/Co and 0.65μ_B/Co, respectively. Furthermore, the crystal growth mode of Co:ZnO films on various oriented LT, the relationship between the microstructures and corresponding ferromagnetic properties are also discussed.     

Investigations on Fe doped polyvinyl alcohol films with and without gamma (γ)-irradiation

This paper deals with the preparation of pure and ferric chloride (FeCl₃) doped polyvinyl alcohol (PVA) films by solution casting method. Optical and electrical properties were systematically investigated. We have found the decrease in optical band gap energy of PVA films on doping FeCl₃. The optical band gap energy values in the present work are found to be 3.10 eV for pure PVA, 2 eV for PVA:Fe³⁺ (5 mol%), 1.91 eV for PVA:Fe³⁺(15 mol%) and 1.8 eV for PVA:Fe³⁺(25 mol%). Direct current electrical conductivity (σ) of pure, FeCl₃ doped PVA films in the temperature range 70-127 °C has been studied. At 387 K dc electrical conductivity of pure PVA film is 5.5795 μ Ω⁻¹ cm⁻¹, PVA:Fe³⁺ (5 mol%) film is 10.0936 μ Ω⁻¹ cm⁻¹ and γ-Irradiated PVA:Fe³⁺ (5 mol%) film for 900 CGY/min is 22.1950 μ Ω⁻¹ cm⁻¹. The result reveals the enhancement of the electrical conductivity with γ-irradiation. FT-IR study signifies the intermolecular hydrogen bonding between Fe³⁺ ions of FeCl₃ with OH group of PVA.     

Microstructures, surface bonding states and room temperature ferromagnetisms of Zn0.95Co0.05O thin films doped with copper

Zn_0.95−xCo_0.05Cu_xO (ZCCO, where x = 0, 0.005, 0.01 and 0.015) thin films were deposited on Si (1 0 0) substrates by pulsed laser deposition technique. Crystal structures, surface morphologies, chemical compositions, bonding states and chemical valences of the corresponding elements for ZCCO films were characterized by X-ray diffraction (XRD), field emission scanning electron microscope (FESEM) and X-ray photoelectron spectroscopy (XPS). XRD and FESEM results indicate that crystallite sizes of the highly (0 0 2)-oriented ZCCO films slightly decrease with increasing Cu content. When the Cu content increases from 0 to 0.015, Zn 2p_3/2, Co 2p, Cu 2p_3/2 and O 1s peaks of the ZCCO film shift towards higher or lower binding energy regions, and the reasons for these chemical shifts are investigated by fitting the corresponding XPS narrow-scan spectra. Both in-plane and out-of-plane magnetization-magnetic field hysteresis loops of the ZCCO films reveal that all the films have room temperature ferromagnetisms (RTFMs). The conceivable origin of the RTFM is ascribed to the combined effects of the local structural disorder resulted from (Co²⁺, Cu²⁺, Cu¹⁺)-cations which substitute Zn²⁺ ions in the ZnO matrices, ferromagnetic coupling between coupled dopant atoms caused by Co²⁺ (3d⁷4s⁰) and Cu²⁺ (3d⁹4s⁰) spin states, and exchange interactions between the unpaired electron spins originating from lattice defects induced by Cu doping in the Zn_0.95Co_0.05O matrices.     

Growth and photoluminescence properties of inclined ZnO and ZnCoO thin films on SrTiO₃（110） substrates

ZnO thin film growth prefers different orientations on the etched and unetched SrTiO 3(STO)(110) substrates.Inclined ZnO and cobalt-doped ZnO(ZnCoO) thin films are grown on unetched STO(110) substrates using oxygen plasma assisted molecular beam epitaxy,with the c-axis 42 inclined from the normal STO(110) surface.The growth geometries are ZnCoO[100]//STO[110] and ZnCoO[111]//STO[001].The low temperature photoluminescence spectra of the inclined ZnO and ZnCoO films are dominated by D 0 X emissions associated with A 0 X emissions,and the characteristic emissions for the 2 E(2G)→ 4A2(4F) transition of Co 2+ dopants and the relevant phonon-participated emissions are observed in the ZnCoO film,indicating the incorporation of Co 2+ ions at the lattice positions of the Zn 2+ ions.The c-axis inclined ZnCoO film shows ferromagnetic properties at room temperature     

Auger electron/X-ray photoelectron and cathodoluminescent spectroscopic studies of pulsed laser ablated SrAl2O4:Eu,Dy thin films

Auger electron/X-ray photoelectron and cathodoluminescent (CL) spectroscopic studies were conducted on pulsed laser deposited SrAl₂O₄:Eu²⁺,Dy³⁺ thin films and the correlation between the surface chemical reactions and the decrease in the CL intensity was determined. The Auger electron and the CL data were collected simultaneously in a vacuum chamber either maintained at base pressure or backfilled with oxygen gas. The data were collected when the films were irradiated for 14 h with 2 keV electrons. The CL emission peak attributed to the 4f⁶5d¹ → 4f⁷ transitions was observed at ∼521 nm and the CL intensity of the peaks degraded at different rates in different vacuum conditions. X-ray photoelectron spectroscopy (XPS) data collected from degraded films suggest that strontium oxide (SrO) and aliminium oxide (Al₂O₃) were formed on the surface of the film as a result of electron stimulated surface chemical reaction (ESSCR).     

Electrochemical corrosion behaviors of a-C:H and a-C:NX:H films

The a-C:H and a-C:N_X:H films were deposited onto silicon wafers using radio frequency (rf) plasma enhanced chemical vapor deposition (PECVD) and pulsed-dc glow discharge plasma CVD, respectively. Raman spectroscopy and X-ray photoelectron spectroscopy (XPS) were used to characterize chemical nature and bond types of the films. The results demonstrated that the a-C:H film prepared by rf-CVD (rf C:H) has lower I_D/I_G ratio, indicating smaller sp² cluster size in an amorphous carbon matrix. The nitrogen concentrations of 2.9 at.% and 7.9 at.% correspond to carbon nitride films prepared with rf and pulse power, respectively.Electrochemical corrosion performances of the carbon films were investigated by potentiodynamic polarization test. The electrolyte used in this work was a 0.89% NaCl solution. The corrosion test showed that the rf C:H film exhibited excellent anti-corrosion performance with a corrosion rate of 2 nA cm⁻², while the carbon nitride films prepared by rf technique and pulse technique showed a corrosion rate of 6 nA cm⁻² and 235 nA cm⁻², respectively. It is reasonable to conclude that the smaller sp² cluster size of rf C:H film restrained the electron transfer velocity and then avoids detriment from the exchange of electrons.     

Comparison of ferromagnetism in n- and p-type magnetic semiconductor thin films of ZnCoO

Both n- and p-type diluted magnetic semiconductor ZnCoO are made by magnetron co-sputtering with, respectively, dopants of Al and dual dopants of Al and N. The two sputtering targets are compound ZnCoO with 5% weight of Co and pure metal Al. Sputtering gases for n- and p-type films are pure Ar and N₂, respectively. These films are magnetic at room temperature and possess free electron- and hole-concentration of 5.34×10²⁰ and 5.27×10¹³ cm⁻³. Only the n-type film exhibits anomalous Hall-effect signals. Magnetic properties of these two types of films are compared and discussed based on measurements of microstructure and magneto-transport properties.     

Swift heavy ion induced modifications in cobalt doped ZnO thin films: Structural and optical studies

Modifications in the structural and optical properties of 100 MeV Ni⁷⁺ ions irradiated cobalt doped ZnO thin films (Zn_1−xCo_xO, x = 0.05) prepared by sol-gel route were studied. The films irradiated with a fluence of 1 × 10¹³ ions/cm² were single phase and show improved crystalline structure with preferred C-axis orientation as revealed from XRD analysis. Effects of irradiation on bond structure of thin films were studied by FTIR spectroscopy. The spectrum shows no change in bonding structure of Zn-O after irradiation. Improved quality of films is further supported by FTIR studies. Optical properties of the pristine and irradiated samples have been determined by using UV-vis spectroscopic technique. Optical absorption spectra show an appreciable red shift in the band gap of irradiated Zn_1−xCo_xO thin film due to sp-d interaction between Co²⁺ ions and ZnO band electrons. Transmission spectra show absorption band edges at 1.8 eV, 2.05 eV and 2.18 eV corresponding to d-d transition of Co²⁺ ions in tetrahedral field of ZnO. The AFM study shows a slight increase in grain size and surface roughness of the thin films after irradiation.     

1.54 μm emission mechanism of Er-doped zinc oxide thin films

Zinc oxide (ZnO) and Er-doped zinc oxide (ZnO:Er) thin films were formed by pulsed laser deposition, and characterized by photoluminescence (PL) and X-ray diffraction (XRD) in order to clarify the 1.54 μm emission mechanism in the ZnO:Er films. Er ions were excited indirectly by the 325 nm line of a He-Cd laser, and the comparison of the ultraviolet to infrared PL data of ZnO and ZnO:Er films showed that the 1.54 μm emission of Er³⁺ in ZnO:Er film appears at the expense of the band edge emission and the defect emission of ZnO. The crystallinity of the films was varied with the substrate temperature and post-annealing, and it was found that the intensity of the 1.54 μm emission is strongly related with the crystallinity of the films. There are three processes leading to the 1.54 μm emission; absorption of excitation energy by the ZnO host, energy transfer from ZnO to Er ions, and radiative relaxation inside Er ions, and it is suggested that the crystallinity plays an important role in the first two processes.     

Structure, magnetic and optical properties of polycrystalline Co-doped TiO2 films

Co-doped TiO₂ films were fabricated under different conditions using reactive facing-target magnetron sputtering. Co doping improves the transformation of TiO₂ from anatase phase to rutile phase. The chemical valence of doped Co in the films is +2. All the films are ferromagnetic with a Curie temperature above 340 K. The average room-temperature moment per Co of the Co-doped TiO₂ films fabricated at 1.86 Pa decreases from 0.74 μ_B at x=0.03 to 0.02 μ_B at x=0.312, and decreases from 0.54 to 0.04 μ_B as x increases from 0.026 to 0.169 for the Co-doped TiO₂ films fabricated at 0.27 Pa. The ferromagnetism originates from the oxygen vacancies created by Co²⁺ dopants at Ti⁴⁺ cations. The optical band gaps value (E_g) of the Co-doped TiO₂ films fabricated at 1.86 Pa decreases linearly from 3.35 to 2.62 eV with the increasing x from 0 to 0.312. For the Co-doped TiO₂ films fabricated at 1.86 Pa, the E_g decreases linearly from 3.26 to 2.53 eV with increasing x from 0 to 0.350.     

Enhancement of room temperature ferromagnetism of Fe-doped ZnO epitaxial thin films with Al co-doping

Epitaxial films of ZnO doped with magnetic ion Fe and, in some cases, with 1% Al show clear evidence of room temperature ferromagnetic ordering. The Al doped optimized samples with carrier concentration n_c∼8.0×10²⁰ cm⁻³ show about 3 times enhanced saturation magnetization (0.58 μ_B/Fe²⁺) than the one with n_c∼3.0×10²⁰ cm⁻³ (0.18 μ_B/Fe²⁺). A clear correlation between the magnetization per transition metal ion and the ratio of the number of carriers to the number of donors have been found as is expected for carrier-induced room temperature ferromagnetism. The transport mechanism of the electrons in all the DMS films at low temperature range has been identified with the Efros's variable range hopping due to the electron-electron Coulomb interaction.     

Ferromagnetism of epitaxially grown CaRu1−xMxO3 (M=Ti, Mn) films

Epitaxial thin films of CaRu_1−xM_xO₃ (M=Ti, Mn) were fabricated on a (0 0 1)-SrTiO₃ substrate by spin-coat method using organometallic solutions (metal alkoxides). Results of X-ray diffraction and transmission electron microscopy indicate that the epitaxial films were grown pseudomorphically so as to align the [0 0 l] axis of the CaRu_1−xM_xO₃ films perpendicular to the (0 0 1) plane of the SrTiO₃ substrate. Ferromagnetism and metal-insulator transition are induced by the substitution of transition metal ions. The occurrence of ferromagnetism was explained qualitatively assuming a TiRu₆ cluster model for CaRu_1−xTi_xO₃ film and a mixed valence model for CaRu_1−xMn_xO₃ film. Ferromagnetism was also observed for layered CaRuO₃/CaMnO₃ film and CaRuO₃/CaMnO₃/CaRuO₃/CaMnO₃ multilayer film and the magnetism was explained by an interfacial exchange interaction model with magnetic Mn³⁺, Mn⁴⁺, and Ru⁵⁺ ions.     

Chemical synthesis of spinel nickel ferrite (NiFe2O4) nano-sheets

The present investigation is related to the deposition of single-phase nano-sheets spinel nickel ferrite (NiFe₂O₄) thin films onto glass substrates using a chemical method. Nano-sheets nickel ferrite films were deposited from an alkaline bath containing Ni²⁺ and Fe²⁺ ions. The films were characterized for their structural, surface morphological and electrical properties by means of X-ray diffraction (XRD), transmission electron microscope (TEM), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), and two-point probe electrical resistivity techniques. The X-ray diffraction pattern showed that NiFe₂O₄ nano-sheets are oriented along (3 1 1) plane. The FT-IR spectra of NiFe₂O₄ films showed strong absorption peaks around 600 and 400 cm⁻¹ which are typical for cubic spinel crystal structure. Microstructural study of NiFe₂O₄ film revealed nano-sheet like morphology with average sheet thickness of 30 nm. The room temperature electrical resistivity of the NiFe₂O₄ nano-sheets was 10⁷ Ω cm.     

Microstructures and multiferroic properties of textured Bi0.8La0.2FeO3 thin films

La-substituted BiFeO₃, Bi_0.8La_0.2FeO₃, thin films were fabricated on Pt/Ti/SiO₂/Si substrates by pulsed laser deposition. X-ray diffraction and high-resolution transmission electron microscope were used to analyze the structures of the films. The results show the films fabricated under optimized growth condition are (0 1 2) textured. X-ray photoemission spectroscopy results indicate that the oxidation state of Fe ion is Fe³⁺ in the films without detectable Fe²⁺. The films show low leakage current and excellent dielectric characters. Multiferroic properties with a remnant ferroelectric polarization of 5.2 μC/cm² and a remanent magnetization of 0.02 μ_B/Fe were established. These results have some implications for further research.     

The effect of different gas atmospheres on luminescent properties of pulsed laser ablated SrAl2O4:Eu,Dy thinfilms

SrAl₂O₄:Eu²⁺,Dy³⁺ thin films were grown on Si (1 0 0) substrates using the pulsed laser deposition (PLD) technique to investigate the effect of vacuum, oxygen (O₂) and argon (Ar) deposition atmospheres on the structural, morphological, photoluminescence (PL) and cathodoluminescence (CL) properties of the films. The films were ablated using a 248 nm KrF excimer laser. Atomic force microscopy (AFM), scanning electron microscopy (SEM), X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDS) and fluorescence spectrophotometry were used to characterize the thin films. Auger electron spectroscopy (AES) combined with CL spectroscopy were employed for the surface characterization and electron-beam induced degradation of the films. Better PL intensities were obtained from the unannealed films prepared in Ar and O₂ atmospheres with respect to those prepared in vacuum. A stable green emission peak at 515 nm, attributed to 4f⁶5d¹→4f⁷ Eu²⁺ transitions were obtained with less intense peaks at 619 nm, which were attributed to transitions in Eu³⁺. After annealing the films prepared in vacuum at 800 °C for 2 h, the intensity of the green emission (520 nm) of the thin film increased considerably. The amorphous thin film was crystalline after the annealing process. The CL intensity increased under prolonged electron bombardment during the removal of C due to electron stimulated surface chemical reactions (ESSCRs) on the surface of the SrAl₂O₄:Eu²⁺, Dy³⁺ thin films. The CL stabilized and stayed constant thereafter.     

Parallel syntheses and thermoelectric properties of Ce-doped SrTiO3 thin films

Thermoelectric properties of single crystalline Ce_xSr_1−xTiO₃ films (0 ≤ x ≤ 0.5) have been studied by using combinatorial pulsed-laser deposition. Temperature gradient method was used for identifying an optimum growth temperature for SrTiO₃ homoepitaxial growth, at which both oxygen stoichiometry and persisting layer-by-layer growth mode could be accomplished. Electrical conductivity (σ) and Seebeck coefficient (S) were measured at room temperature for the composition-spread films grown at the optimized temperature and found to be considerably higher than those reported for bulk poly-crystalline compounds. Hall measurement revealed that carrier density linearly increased with increasing x, suggesting that a trivalent Ce ions substituted divalent Sr ions to supply electrons. A maximum power factor (S²σ) was obtained for the x = 0.2 film, being 7 and 14 μW/K² cm at 300 and 900 K, respectively.     

Influence of high-energy electron irradiation on field emission properties of multi-walled carbon nanotubes (MWCNTs) films

The effect of very high energy electron beam irradiation on the field emission characteristics of multi-walled carbon nanotubes (MWCNTs) has been investigated. The MWCNTs films deposited on silicon (Si) substrates were irradiated with 6 MeV electron beam at different fluence of 1×10¹⁵, 2×10¹⁵ and 3×10¹⁵ electrons/cm². The irradiated films were characterized using scanning electron microscope (SEM) and micro-Raman spectrometer. The SEM analysis clearly revealed a change in surface morphology of the films upon irradiation. The Raman spectra of the irradiated films show structural damage caused by the interaction of high-energy electrons. The field emission studies were carried out in a planar diode configuration at the base pressure of ∼1×10⁻⁸ mbar. The values of the threshold field, required to draw an emission current density of ∼1 μA/cm², are found to be ∼0.52, 1.9, 1.3 and 0.8 V/μm for untreated, irradiated with fluence of 1×10¹⁵, 2×10¹⁵ and 3×10¹⁵ electrons/cm². The irradiated films exhibit better emission current stability as compared to the untreated film. The improved field emission properties of the irradiated films have been attributed to the structural damage as revealed from the Raman studies.