Functionalization of graphene with Prussian blue and its application for amperometric sensing of H2O2

As a two-dimensional carbon material with high surface area and conductivity, graphene shows great promise for designing composite nanomaterials to achieve high-performance electrochemical devices. In this work, we prepared graphene-based nanocomposite material by electrochemically depositing Prussian blue (PB) nanoparticles on the surface of graphene. Fourier transform infrared spectra, SEM, and cyclic voltammetry were used to characterize the successful immobilization of PB. Compared with PB films and graphene sheets, the PB–graphene composite films showed the largest current response to the reduction of H₂O₂, probably due to the synergistic effects between graphene sheets and PB nanoparticles. Therefore, a fast and highly sensitive amperometric sensor for H₂O₂ was obtained with a detection sensitivity of 1.6 μA μM^?1 H₂O₂ per cm² and a linear response range of 50～5,000 μM. The detection limit of H₂O₂ was 20 nM at a signal-to-noise ratio of 3. These obtained results are much better than those reported for carbon nanotubes-based amperometric sensors.     

Novel self assembled magnetic Prussian blue graphene based aerogel for highly selective removal of radioactive cesium in water

A novel self-assembled Magnetic Prussian Blue/Reduced Graphene Oxide (3D-MPBRGO) aerogel was prepared by an easy and cost effective process for elimination of radioactive Cesium from contaminated aqueous solution selectively. The 3D-MPBRGO displayed excellent adsorption capability of 3.64 mmol per g or (484.12 mg/g) for Cs (initial 50 mM cesium concentration, pH 7 and 30 °C) and quick separation from solution by applying magnetic field as compared to previously published results for graphene based adsorbents. This excellent removal efficiency of nanocomposite can be ascribed to enlarged adsorbent surface area (402.68 m²/g) and uniform distribution of nanoparticles on RGO which removes aggregation of sheets as well. The thermodynamic analysis displayed exothermic and spontaneous nature of Cs ion adsorption. The experimental data of adsorption isotherm followed the Langmuir isotherm model than that of Tempkin and Freundlich while adsorption kinetics followed pseudo second order.     

Layer-by-layer assembled multilayer of graphene/Prussian blue toward simultaneous electrochemical and SPR detection of H2O2

A new type of chemically converted graphene sheets, cationic polyelectrolyte-functionalized ionic liquid decorated graphene sheets (PFIL-GS) composite, was synthesized and characterized by Ultraviolet-visible (UV-vis) absorption, Fourier transform infrared, and Raman spectroscopy. It was found that the presence of PFIL enabled the formation of a very stable aqueous dispersion due to the electrostatic repulsion between PFIL modified graphene sheets. With respect to the excellent dispersibility of this material, we have fabricated a novel PFIL-GS/Prussian blue (PB) nanocomposite multilayer film via classic layer-by-layer (LBL) assembly. The assembly process was confirmed by UV-vis spectroscopy and surface plasmon resonance (SPR) spectroscopy, which showed linear responses to the numbers of the deposited PFIL-GS/PB bilayers. Moreover, the as-prepared composite films were used to detect hydrogen peroxide (H₂O₂) by electrochemical surface plasmon resonance (EC-SPR) spectroscopy. This real time EC-SPR technique can provide simultaneous monitoring of both optical SPR signal and electrochemical current responses upon injecting H₂O₂ into the reaction cell. The experimental results revealed that both the electrochemical and SPR signal exhibited splendid linear relationship to the concentration of the injected H₂O₂, and the detection limit could be up to 1 μM.     

Photochemical synthesis of Prussian blue film from an acidic ferricyanide solution and application

We describe a novel photochemical method to synthesize compacted Prussian blue (PB) film from an acidic ferricyanide solution. The key step is the photochemical reduction of ferricyanide ion to ferrocyanide ion that subsequently coordinates with the free ferric ion dissociated from the ferricyanide in acidic medium to form Prussian blue on the illuminated electrode surface. The prepared PB film electrode shows high electrocatalytic activity towards the reduction of hydrogen peroxide and the amperometric responses show a linear dependence on the concentration of hydrogen peroxide in a range of 1.0 × 10⁻⁶ to 1.2 × 10⁻³ M with a detection limit down to 4 × 10⁻⁷ M. The present photochemical method provides a simple and promising route for the local fabrication of patterned molecular magnets, ion-selective sensors, and electro- or photochromic devices.     

Label-free amperometric immunosensor based on prussian blue as artificial peroxidase for the detection of methamphetamine

A label-free amperometric immunosensor for the detection of methamphetamine was developed. The prussian blue deposited/l-cystine-modified electrode was covered with nano-Au/(3-mercaptorpropyl) trime-thoxysilane film. Then, the nano-Au was used for the immunosensor platform to capture a large amount of anti-methamphetamine. PB exhibited excellent electrocatalytical properties toward the reduction of H₂O₂ at low overpotentia to amplify the amperometric signal, which enhanced the sensitivity of the immunosensor. The active sites of PB could be shielded and the access of H₂O₂ from solution to the electrode might be partially blocked after the completion of immunoassay, led to a linear decrease in the response current of the electrode over the range from 1.0 × 10⁻⁸ to 5.0 × 10⁻⁶ mol L⁻¹of MA. The obtained immunosensor displayed excellent catalytic reduction toward H₂O₂ due to high activity and selectivity of PB. The influence of relevant experimental variables, including the construction of immunosensor platform, the amount of MPS and the time of immunoaction, was examined and optimized.     

Prussian blue solid-state films and membranes as potassium ion-selective electrodes

The use of thin films of Prussian blue and heterogeneous Prussian blue membranes as potassium ion-selective electrodes was investigated. All of the heavier group I cations and NH⁺₄ interfere strongly but there is relatively good selectivity towards Na⁺ with a selectivity coefficient of ca. 5 × 10^?3. The thin-film measurements, based on Prussian blue deposited on platinum, involve conditioning the electrode to a fixed potential according to the method used by Engel and Grabner for copper hexacyanoferrate(III) films. The membrane electrodes were based on mixing Prussian blue with polymeric supporting films such as polystyrene and epoxy. A particularly simple practical configuration involves Prussian blue membranes deposited directly on copper conductors where one membrane serves as a reference electrode. A reversible cell, without liquid junction, is formed with Prussian blue and Ag/AgCl electrodes and this serves as a means for determining an accurate value for the standard reduction potential of Prussian blue, which is found to be 0.238 V vs. Ag/AgCl at 25 °C.     

Visualization of latent fingerprints using Prussian blue thin films

Herein,a facile and effective approach was proposed for visualizing latent fingerprints(LFPs) on two kinds of conductive surfaces by spatially selective electrochemical deposition of Prussian blue(PB) thin films.This strategy exploited the fingerprint residue as an insulating mask and the PB thin films were only generated on the bare surface including the valleys between the papillary ridges,which produced a negative image of LFPs with high resolution up to the third level information.The surface morphology of PB films was characterized by the field emission scanning electron microscopy(FE-SEM).This enhancement technique showed promising performance in selected materials of practical interest.     

Electrochromism and electrochemical magnetism in Ni–Fe Prussian blue

We studied the electrochemical and magnetic properties of NiFe Prussian blue. The NiFe Prussian blue was synthesized on Ni electrodes in the form of thin films by an electrochemical technique. Measurements of its magnetic properties show that NiFe Prussian blue with the Fe^{III-low spin (LS)}–CN–Ni^II structure exhibits ferromagnetic properties, with T _c (critical temperature)=25 K. On the other hand, the reduced form, which has the Fe^II-LS–CN–Ni^II structure, is paramagnetic. This means that the magnetic properties can be controlled between ferromagnetic and paramagnetic by an electrochemical method. Furthermore, it is well known that NiFe Prussian blue exhibits electrochromic properties. Hence, this compound is a multifunctional, molecule-based compound in which optical and magnetic properties can be controlled by an electrochemical redox reaction. Contribution to the special issue on “Magnetic field effects in Electrochemistry.”     

中空和基底支撑型普鲁士蓝及其类似物和衍生物用于绿色水分解

随着世界对能源需求的日益增长,为减少对化石燃料的严重依赖同时实现碳达峰和碳中和,迫切需要探索发现新型能源和能源载体.与其他燃料相比,氢气具有零碳排放、能量密度高、清洁可再生和来源广泛等特点,因此被认为是理想的能源载体.目前,工业制氢主要有三种策略,分别是甲烷水蒸气重整(SMR)、煤炭水蒸气(CG)和水电解(WE).其中SMR和CG制氢占95％,而WE制氢仅占4％.虽然前二者制氢成本较低,但会伴生大量的二氧化碳,相比之下,WE制氢纯度高,绿色无污染,更加符合目前的环保理念.目前WE制氢的核心问题之一就是设计和合成高效、廉价的电催化剂.具有类贵金属催化性能的过渡金属基电催化剂(例如钴基、镍基和铁基材料)已经引起了学术界的广泛关注.配位聚合物(CP)由于其具有固有的金属元素、内部结构化学可调、比表面积大和结构有序等优点,在吸附、催化和储能等领域得到了广泛的应用.作为18世纪发现的第一个人工配位聚合物,普鲁士蓝(PB)及其类似物(PBAs)和具有可调金属中心的衍生物作为一种新型的光催化剂或电催化剂受到了广泛的关注.本综述详细介绍了以普鲁士蓝及其类似物和衍生物构筑的中空结构和基底支撑型纳米材料在绿色水分解方面的基础研究及应用进展.本文首先简单介绍了普鲁士蓝及其类似物的基本结构组成,并对其优缺点进行了总结;随后,针对普鲁士蓝及其类似物的中空结构的合成策略和形成机理展开了详细地阐述,包括单层中空纳米盒、开孔式纳米笼以及复杂中空结构等;此外,针对基底支撑型普鲁士蓝及其类似物结构合成机理也进行了详细地解释,包括泡沫镍网、铁网、碳布、铜网等基底,并与中空结构进行了对比总结,该类负载型结构可以充分发挥活性位的利用效率,达到更好的催化性能.此外,结合最新的研究进展,介绍了普鲁士蓝及其类似物和衍生物(氢氧化物、磷化物、硫族化合物和碳化物)在水裂解中的应用,包括电解水和光催化制氢,并对电解水的机理进行了总结.最后,本文总结了该领域目前存在的局限性和面临的紧迫挑战.希望本综述能够激发更多研究者投身于复杂结构普鲁士蓝及其类似物和衍生物的高效绿色水裂解方面的研究工作.     

One-pot green synthesis of Prussian blue nanocubes decorated reduced graphene oxide using mushroom extract for efficient 4-nitrophenol reduction

One-pot green approach to the synthesis of Prussian blue nanocubes/reduced graphene oxide (PBNCs/RGO) nanocomposite had been attempted. It was based on the extract of mushroom with K₃[Fe(CN)₆] and graphene oxide (GO) as precursors, where the reduction of GO and the deposition of PBNCs occurred simultaneously. The obtained nanocomposite was characterized by transmission electron microscopy (TEM), scanning electron microscopy (SEM), X-ray diffraction (XRD), Raman spectroscopy and electrochemical techniques. With the introduction of β-cyclodextrin (β-CD), the β-CD/PBNCs/RGO system showed linear behavior in the range from 0.01 to 700 μM for 4-nitrophenol with a low detection limit of 2.34 nM (S/N = 3).     

Sensitive detection of potassium ion using Prussian blue nanotube sensor

A model K⁺ sensor using Prussian blue nanotubes is fabricated by electrochemical deposition of Prussian blue (PB) within the nanochannels of a porous metal-coated membrane with partially covered pore openings. The PB nanotube sensor exhibits excellent stability giving reproducible peak potentials up to 500 measurement cycles, a very low detection limit of 2.0 × 10⁻⁸ M and extremely wide logarithmic linear ranges between 5.0 × 10⁻⁸–7.0 × 10⁻⁴ M and 7.0 × 10⁻⁴–1.0 M. Negligible interferences by Na⁺, Mg²⁺ and Ca²⁺ are observed and a rapid analysis time of 30 s is readily achieved. The ease of electrodeposition, high stability of PB nanotubes and outstanding analytical performance which surpasses conventional PB voltammetric and potentiometric sensors demonstrates potential sensing applications including ion sensors and biosensors using PB and other metal hexacyanoferrate nanotubes.     

Phosphomolybdic acid functionalized graphene loading copper nanoparticles modified electrodes for non-enzymatic electrochemical sensing of glucose

A sensitive non-enzymatic glucose electrochemical biosensor (Cu/PMo₁₂-GR/GCE) was developed based on the combination of copper nanoparticles (CuNPs) and phosphomolybdic acid functionalized graphene (PMo₁₂-GR). PMo₁₂-GR films were modified on the surface of glassy carbon electrode (GCE) through electrostatic self-assembly with the aid of poly diallyl dimethyl ammonium chloride (PDDA). Then CuNPs were successfully decorated onto the PMo₁₂-GR modified GCE through electrodeposition. The morphology of Cu/PMo₁₂-GR/GCE was characterized by scanning electron microscope (SEM). Cyclic voltammetry (CV) and chronoamperometry were used to investigate the electrochemical performances of the biosensor. The results indicated that the modified electrode displayed a synergistic effect of PMo₁₂-GR sheets and CuNPs towards the electro-oxidation of glucose in the alkaline solution. At the optimal detection potential of 0.50 V, the response towards glucose presented a linear response ranging from 0.10 μM to 1.0 mM with a detection limit of 3.0 × 10⁻² μM (S/N = 3). In addition, Cu/PMo₁₂-GR/GCE possessed a high selectivity, good reproducibility, excellent stability and acceptable recovery, which indicating the potential application in clinical field.     

Spectroelectrochemical identity of Prussian blue films in various electrolytes: comparison of time-derivative voltabsorptometric responses with conventional cyclic voltammetry

Using Prussian blue (PB) electrodeposited on gold-covered foil as a model system, we have demonstrated the usefulness of the time-derivative measurements of absorbance versus potential (linear potential-scan voltabsorptometry) for spectroelectrochemical characterization of thin electrochromic films. The time-derivative signals were monitored for PB at 680 and 420 nm in potassium, sodium and lithium electrolytes. Information obtained from cyclic voltabsorptometry is equivalent or complementary to that from conventional cyclic voltammetry. In the case of PB films investigated in lithium electrolyte, the voltabsorptometric time-derivative peaks are better defined than the respective voltammetric peaks. The combination of voltabsorptometry with voltammetry enables molar absorptivity and/or film loading to be determined. Also, concentration changes of differently colored mixed-valence redox centers can be monitored as a function of applied potential. Received: 16 January 1997 / Accepted: 11 March 1997     

Cyclic voltammetric studies of Prussian blue and viologens within a paper matrix for electrochromic printing applications

The apparent redox response of Prussian blue (PB, iron(III) hexacyanoferrate(II)) within a paper matrix is similar to that found in conventional liquid electrolyte voltammetry using a PB-modified electrode; however part of the response is from PB which adsorbs onto the glassy carbon (GC) working electrode. Application of a Nafion® coating to the PB-impregnated paper matrix prevents transfer of PB to the GC surface. In contrast to the PB system, the redox response of the 1,1′-dimethyl-4,4′-bipyridilium (MV, methyl viologen) system, where both redox states examined are soluble, is confined wholly to the paper matrix. For the case of 1,1′-diheptyl-4,4′-bipyridilium (HV, heptyl viologen), the electrogenerated insoluble radical cation salt adsorbs onto the GC electrode, the KCl-impregnated paper acting simply as the electrolyte medium. PB can be electrogenerated within a paper matrix, with the possible application in monochrome electrochromic printing systems.     

Polyacrylonitrile-based gel polymer electrolyte filled with Prussian blue forhigh-performance lithium polymer batteries

Lithium polymer batteries(LPBs) rely on a high ion transport to gain improved cell performance.Thermostable and porous gel polymer electrolytes(GPEs) have attracted much attention due to their excellent properties in electrolyte wettability and ionic conductivity.In this work,iron-nickel-cobalt trimetal Prussian blue analogue(PBA) nanocubes are filled into the electro spun polyacrylonitrile(PAN)-based membranes to generate GPE composites with morphological superiority consisting of fine fibers and interconnected pores.The thus obtained PBA@PAN fibrous membrane showcases good thermal stability,high porosity and electrolyte uptake,as well as a peak io nic conductivity of 2.7 mS/cm with the addition of 10% PBA,Consequently,the assembled lithium iron phosphate(LiFePO_4) battery using PBA@PAN-10 as the GPE delivers a high capacity of 152.2 mAh/g at 0.2 C and an ultralow capacity decay of0.09% per cycle in a long-te rm cycle life of 350 cycles at 1 C,endorsing its promising applications in LPBs.     

Detection protein biomarker with gold nanoparticles functionalized hollow mesoporous Prussian blue nanoparticles as electrochemical probes

Gold nanoparticles functionalized hollow mesoporous Prussian blue nanoparticles(Au@HMPB NPs)were synthesized and its peroxidase-like activity was explored for electrochemical probe.The Au@HMPB NPs can reduce H2O2 low detection potential of-0.1 V with high sensitivity.After physically adsorption of antibodies onto the gold nanoparticle surface,the functionalized nanoparticles were turned into immuno-probe.The soluble a-chain of interleukin-2(IL-2)receptor(sCD25)was chosen as a model protein biomarker to test the performance of the probe.sCD25 in the samples were captured and enriched by capture anti-CD25 antibody functionalized magnetic nanospheres.Detection antibody functionalized Au@HMPB can then be linked onto the nanospheres and generate electrochemical current towards H2O2 reduction.The electrochemical responses to 1 mmol/L H2O2 was increased with the increasing concentration of CD25.     

Adsorption of cesium using mesoporous silica gel evenly doped by Prussian blue nanoparticles

In this paper, a novel mesoporous silica gel evenly doped by Prussian blue nanoparticles (PBMSG) was successfully synthesized by using N,N-dimethylamide as template with a large Barrett-Emmett-Teller (BET) surface area of 505 m²/g and an average pore size of 2.9 nm. The static adsorption experiments showed that the equilibration time of PBMSG for Cs⁺ was about 30 min. The adsorption isotherm of PBMSG for Cs⁺ accorded with Langmuir model and the theoretical maximum adsorption capacity was 80.0 ± 2.9 mg/g. When the initial concentration of Cs⁺ was 1.00 mg/L, the adsorption partition coefficient K_d could reach 3.5 × 10⁴ mL/g After adsorption, Cs⁺ could be eluted by dilute hydrochloric acid (pH 2) with an efficiency of 89.8%, while no K⁺, Fe³⁺, Fe²⁺ was eluted. PBMSG exhibited good selectivity toward Cs⁺ and Rb⁺. In the presence of high concentration of K⁺, the selective adsorption of PBMSG could change the mass ratio of K⁺, Rb⁺ and Cs⁺ from 96.63:0.83:1.00–1.12:0.73:1.00. The separation of Cs⁺ and Rb⁺ from K⁺ with similar concentration (100 mg/g) was realized by column experiment. This indicated that PBMSG was suitable for rapid recovery of low concentration of rubidium and cesium from complex matrixes, such as wastewater and salt lake brine, etc.     

A Simple and Sensitive Method for the Amperometric Detection of Trace Chromium(VI) Based on Prussian Blue Modified Glassy Carbon Electrode

A simple and sensitive method for the amperometric detection of trace amount of chromium(VI) using a Prussian blue modified glassy carbon electrode (PB/GCE) is described here. The Everitts salt/Prussian blue redox couple of the PB film was found to mediate the Cr(VI) reduction, and the mechanism of electrochemical reaction was investigated. The effects of PB film thickness, applied potential and electrolyte solution on the current response of Cr(VI) reduction were thoroughly studied. Under the optimized conditions, the PB/GCE provided a wide linear range for Cr(VI) analysis from 0.5 to 200 ppb with excellent sensitivity (15±0.2 nA/ppb) and low detection limit (0.15 ppb). In addition, the modified electrode showed excellent stability, reproducibility and good resistance to other metal ions and surfactants. Finally, the proposed method was applied to detect trace Cr(VI) in wastewater with satisfactory results. The great advantages of the method were characterized by the simplicity, ease of preparation, stability, short analysis time and cost‐efficiency.