用锌有机源和CO2/H2混合气源PECVD沉积ZnO薄膜

在等离子体作用下,以CO2/H2混合气为氧源,Zn(C2H5)2锌为锌源,在单晶硅上生长出高度择优取向的氧化锌薄膜。X射线衍射分析表明,薄膜为六方结构,c轴高度择优;原子力显微镜观察到晶粒是有规律地按六方排布,薄膜的表面粗糙度较小;从光致发光谱还发现在380 nm处有非常强的紫外峰。     

Deposition of tungsten nitride thin films by plasma focus device at different axial and angular positions

Tungsten nitride thin films were deposited on stainless steel-304 substrates by using a low energy (2 kJ) Mather type plasma focus device. X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM) and microhardness are used to study the surface of treated samples. The XRD analysis shows that the degree of crystallinity of deposited thin films strongly depends on axial and angular positions of samples. The SEM micrographs of the deposited films at different angular positions (0°, 10° and 30°) and axial position of 8 cm show that the content of WN sub-micro crystalline structures on the surface of deposited films decreased with increasing the angle with respect to anode axis. From AFM results we observe that for the sample deposited at 8 cm and 0° axial and angular positions, respectively, the most uniform surface and the most homogenous distribution of grains are obtained. Also the hardness results show that the highest mechanical hardness is obtained when the film is deposited at 8 cm and 0° axial and angular positions, respectively.     

CO sensor derived from mesostructured Au-doped SnO2 thin film

Pure and Au-doped mesostructured SnO₂ thin films were successfully prepared by using non-ionic surfactant Brij-58 (polyoxyethylene acyl ether) as organic template and tin tetrachloride and hydrogen tetrachloroaurate(III) trihydrate as inorganic precursor. Thin films were deposited onto the glass substrates at 450 °C by simple spray pyrolysis technique. The novel mesostructured tin oxide thin films with different Au concentration exhibit highly selective response towards CO. The correlation of the Au incorporation in the mesostructure with particular morphology and gas sensing behavior is discussed using scanning electron microscopy (SEM), X-ray diffraction (XRD), BET surface area and transmission electron microscopy (TEM) studies.     

Influence of deposition conditions on nanostructured InSe thin films

In this study, nanostructured indium selenide (InSe) thin films were deposited on Indium tin oxide (ITO)-coated glass substrate using electrochemical deposition (ECD) from aqueous solution containing In(SO₄)₃.H₂O and SeO₂. The effects of deposition potential (−0.70 to −1.35 V), time (30-3600 s), temperature (25-80 °C) and pH (2.58 for A samples; 2 for B samples and 1.45 for C samples) on growth of the InSe thin films were examined in terms of their structural, morphological and optical properties. X-ray diffraction (XRD) analysis confirmed that the InSe thin films are in polycrystalline structure. It was found that the values of grain size decreased and the full width half maximum (FWHM) values increased with the increasing deposition potential. According to the absorption measurements, optical properties of the thin films varied with changes in deposition conditions. Based on the atomic force microscopy (AFM) and the scanning electron microscopy (SEM) images, surface morphology of the thin films was influenced by deposition potential and pH of the electrolyte, and non-homogeneous depositions distributed across the entire surface were observed. In addition, Raman spectroscopy, X-ray photoelectron spectroscopy (XPS) and fourier transform infrared spectroscopy (FT-IR) analyses were used to further examine crystal quality, vibration, chemical binding conditions, In/Se orientation and structure of the prepared InSe thin films. When Raman results are examined, the B12 sample shows a more intensity and narrow peak at 248 cm⁻¹. XPS measurements sowed that A6 sample exhibited more growth in low potential for a long time and better film stoichiometry compared to the other three samples. Also, FT-IR studies prove the presence of InSe. According to the results, the film did not form at low temperatures and short times. However, the film formation began with the increasing deposition temperature and time at the low potential value of −0.730 V. But, it is clear that a high quality film can be obtained in cathodic potential with −1.3 V and shorter deposition time with 300 s at room temperature respectively. Overall results showed that the high quality thin films can be obtained by the ECD technique. However, deposition conditions must be sensitively adjusted to control morphology of the electrodeposited nanoparticles.     

HFCVD法制备纳米晶体碳化硅薄膜中氢流量对晶粒尺寸的影响

以甲烷、硅烷和氢气为反应气体,采用热丝化学气相沉积(HFCVD)法在单晶硅衬底上沉积纳米晶体碳化硅(SiC)薄膜.通过X射线衍射(XRD)和扫描电子显微镜(SEM)分别对SiC薄膜的晶体结构和表面形貌进行分析.实验发现氢气流量对碳化硅薄膜晶粒尺寸有很大影响,当氢气流量从10SCCM变化到300SCCM时,薄膜晶粒的平均尺寸将由较大的400 nm左右减小到40 nm左右.     

HFCVD法制备纳米晶体碳化硅薄膜中氢流量对晶粒尺寸的影响

以甲烷、硅烷和氢气为反应气体,采用热丝化学气相沉积（HFCVD）法在单晶硅衬底上沉积纳米晶体碳化硅(SiC)薄膜.通过X射线衍射(XRD)和扫描电子显微镜（SEM）分别对SiC薄膜的晶体结构和表面形貌进行分析.实验发现氢气流量对碳化硅薄膜晶粒尺寸有很大影响,当氢气流量从10SCCM变化到300SCCM时,薄膜晶粒的平均尺寸将由较大的400 nm左右减小到40 nm左右.     

Structure, morphology and optical properties of SiO2−x thin films prepared by plasma-assisted pulsed laser deposition

The amorphous silicon oxide SiO_2−x thin films were prepared by the plasma-assisted pulsed laser deposition (PLD) method. X-ray diffraction spectrometry (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), UV-VIS-NIR scanning spectrophotometry and ellipsometry were used to characterize the crystallinity, microscopic morphology and optical properties of obtained thin films. The influences of substrate temperatures, oxygen partial pressures and oxygen plasma assistance on the compositions of silicon oxide (SiO_2−x) thin films were investigated. Results show that the deposited thin films are amorphous and have high surface quality. Stoichiometric silicon dioxide (SiO₂) thin film can be obtained at elevated temperature of 200 °C in an oxygen plasma-assisted atmosphere. Using normal incidence transmittance, a novel and simple method has been proposed to evaluate the value of x in transparent SiO_2−x thin films on a non-absorbing flat substrate.     

The comparison between CdS thin films grown on Si(111) substrate and quartz substrate by femtosecond pulsed laser deposition

Two kinds of cadmium sulfate (CdS) thin films have been grown at 600 °C onto Si(111) and quartz substrates using femtosecond pulsed laser deposition (PLD). The influence of substrates on the structural and optical properties of the CdS thin films grown by femtosecond pulsed laser deposition have been studied. The CdS thin films were characterized by X-ray diffraction (XRD), atomic force microscopy (AFM), scanning electron microscopy (SEM), photoluminescence (PL) and Raman spectroscopy. Although CdS thin films deposited both on Si(111) and quartz substrates were polycrystalline and hexagonal as shown by the XRD , SEM and AFM results, the crystalline quality and optical properties were found to be different. The size of the grains for the CdS thin film grown on Si(111) substrate were observed to be larger than that of the CdS thin film grown on quartz substrate, and there is more microcrystalline perpendicularity of c-axis for the film deposited on the quartz substrate than that for the films deposited on the Si substrate. In addition, in the PL spectra, the excitonic peak is more intense and resolved for CdS film deposited on quartz than that for the CdS film deposited on Si(111) substrate. The LO and TO Raman peaks in the CdS films grown on Si(111) substrate and quartz substrate are different, which is due to higher stress and bigger grain size in the CdS film grown on Si(111) substrate, than that of the CdS film grown on the amorphous quartz substrate. All this suggests that the substrates have a significant effect on the structural and optical properties of thin CdS films. PACS 81.15.Fg; 81.05.Ea; 78.20.-e; 78.67.-n; 42.62.-b     

Effects of deposition temperature on the structural and morphological properties of SnO2 films fabricated by pulsed laser deposition

Tin oxide (SnO₂) thin films were grown on Si (1 0 0) substrates using pulsed laser deposition (PLD) in O₂ gas ambient (10 Pa) and at different substrate temperatures (RT, 150, 300 and 400 °C). The influence of the substrate temperature on the structural and morphological properties of the films was investigated using X-ray diffraction (XRD), atomic force microscopy (AFM) and scanning electron microscopy (SEM). XRD measurements showed that the almost amorphous microstructure transformed into a polycrystalline SnO₂ phase. The film deposited at 400 °C has the best crystalline properties, i.e. optimum growth conditions. However, the film grown at 300 °C has minimum average root mean square (RMS) roughness of 3.1 nm with average grain size of 6.958 nm. The thickness of the thin films determined by the ellipsometer data is also presented and discussed.     

Surface structure and composition of flat titanium thin films as a function of film thickness and evaporation rate

To correlate flat titanium film surface properties with deposition parameters, titanium flat thin films were systematically deposited on glass substrates with various thicknesses and evaporation rates by electron-beam evaporation. The chemical compositions, crystal structure, surface topographies as well as wettability were investigated by using X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), atomic force microscopy (AFM) and water contact angle measurement, respectively. The films consisted mainly of TiO₂. Small percentages of Ti₂O₃ and metallic Ti were also found at the film surface using high-resolution XPS analysis. Quantitative XPS showed little differences regarding elemental compositions among different groups of films. The films were obtained by varying the deposition rate and the film thickness, respectively. XRD data showed consistent reflection patterns of the different titanium samples deposited using different film thicknesses. Without exception measurements of all samples exhibited contact angles of 80° ± 5°. Quantitative AFM characterization demonstrated good correlation tendency between surface roughness and film thickness or evaporation rate, respectively. It is important to notice that titanium films with different sizes of grains on their surfaces but having the same chemistry and film bulk structure can be obtained in a controllable way. By increasing the film thickness and evaporation rate, the surface roughness increased. The surface morphology and grain size growth displayed a corresponding trend. Therefore, the control of these parameters allows us to prepare titanium films with desired surface properties in a controllable and reproducible way for further biological investigations of these materials.     

Optimization of spray parameters in the fabrication of SnO2 layers using electrostatic assisted deposition technique

Tin oxide (SnO₂) thin films for gas sensing applications were prepared using electrostatic spray deposition method under optimum deposition conditions. It is shown in the paper that desired film morphology can be obtained by controlling different spray parameters (liquid properties, applied voltage, nozzle-substrate distance and substrate temperature). The spray parameters were optimized with respect to droplet diameter and applied voltage. An empirical relationship between critical voltage and different spray parameters was established for optimization. The morphology of the films prepared using these optimized spray parameters were investigated using X-Ray Diffraction (XRD) and Scanning Electron Microscope (SEM).     

Multilayered metal oxide thin film gas sensors obtained by conventional and RF plasma-assisted laser ablation

Multilayered thin films of In₂O₃ and SnO₂ have been deposited by conventional and RF plasma-assisted reactive pulsed laser ablation, with the aim to evaluate their behaviour as toxic gas sensors. The depositions have been carried out by a frequency doubled Nd-YAG laser (λ = 532 nm, τ = 7 ns) on Si(1 0 0) substrates, in O₂ atmosphere. The thin films have been characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and electrical resistance measurements. A comparison of the electrical response of the simple (indium oxide, tin oxide) and multilayered oxides to toxic gas (nitric oxide, NO) has been performed. The influence on the structural and electrical properties of the deposition parameters, such as substrate temperature and RF power is reported.     

Characteristics of sculptured Cu thin films and their optical properties as a function of deposition rate

Sculptured copper thin films were deposited on glass substrates, using different deposition rates. The nano-structure and morphology of the films were obtained, using X-ray diffraction (XRD), atomic force microscopy (AFM) and scanning electron microscopy (SEM). Their optical properties were measured by spectrophotometry in the spectral range of 340-850 nm. The real and imaginary refractive indices, film thickness and fraction of metal inclusion in the film structure were obtained from optical fitting of the spectrophotometer data.     

Substrate dependent properties of electrodeposited EuTe thin films

In electrodeposition, substrate besides providing mechanical support to the electrodeposit, affects significantly the structural and morphological properties of a film. Electrodeposition and characterization of EuTe thin films onto different substrates such as stainless steel (SS), titanium (Ti), copper (Cu), fluorine-doped tin oxide (F:SnO₂) covered glasses have been described. The deposition potentials have been estimated from the polarization curves. The reaction mechanism is proposed for the formation of EuTe electrodeposits. Preparative parameters such as deposition potential, current density, and deposition time are studied. The films have been characterized by X-ray diffraction, scanning electron microscopy (SEM), atomic force microscopy (AFM) and energy dispersive analysis by X-rays (EDAX) techniques. The electrodeposited EuTe films are polycrystalline on all the substrates with same cubic crystal structure. The SEM studies reveal that the surface morphology is different for the substrates studied. However, no cracks have been observed in the SEM micrographs. The AFM images show large spherical grains supporting the polycrystalline nature of the samples. The EDAX analysis shows that the EuTe films are nearly stoichiometric, slightly rich in tellurium.     

Nanomechanical characterization of amorphous hydrogenated carbon thin films

Amorphous hydrogenated carbon (a-C:H) thin films deposited on a silicon substrate under various mixtures of methane-hydrogen gas by electron cyclotron resonance microwave plasma chemical vapor deposition (ECR-MPCVD) was investigated. Microstructure, surface morphology and mechanical characterizations of the a-C:H films were analyzed using Raman spectroscopy, atomic force microscopy (AFM) and nanoindentation technique, respectively. The results indicated there was an increase of the hydrogen content, the ratio of the D-peak to the G-peak (I_D/I_G) increased but the surface roughness of the films was reduced. Both hardness and Young's modulus increased as the hydrogen content was increased. In addition, the contact stress-strain analysis is reported. The results confirmed that the mechanical properties of the amorphous hydrogenated carbon thin films improved using a higher H₂ content in the source gas.     

Surface characterization of TiO2 thin films obtained by high-energy reactive magnetron sputtering

This paper presents the results of surface characterization of TiO₂ thin films deposited on different substrates by the use of high-energy reactive magnetron sputtering. Structural investigations carried out by X-ray diffraction (XRD) and atomic force microscopy (AFM) have shown a strong influence of both the substrate type, and its placement in the deposition chamber (relative to the sputtering target), on the structural properties of the films. In all cases, there is evidence for pseudoepitaxial growth. XRD examination showed existence of TiO₂-rutile phase with preferred (1 1 0) orientation and AFM measurements revealed nanocrystalline structure directly after deposition. X-ray photoelectron spectroscopy analysis showed that the TiO₂ films have stoichiometric composition.     

Hydrogenation of Pd-capped Mg thin films prepared by DC magnetron sputtering

Structural and optical properties of pure Mg thin film coated with Pd have been investigated. Pd-capped Mg thin films had been prepared by DC magnetron sputtering. This work presents an ex situ study on hydrogenation and dehydrogenation kinetics of Pd/Mg films at different conditions using XRD, AFM and optical spectrophotometer. We have succeeded to load thin films of Mg to MgH₂ at normal temperature and normal pressure of hydrogen gas. In hydrogenation, α-MgH₂ phase of magnesium hydride was observed in hydrogenated films at 200 °C and γ-MgH₂ at 250 °C respectively. The desorption kinetics in vacuum also revealed the phase transformation α-MgH₂ to γ-MgH₂. A reflectance change was observed in hydrogenated films in comparison of as deposited thin film. Hydrogenated (H loaded) samples were observed partially transparent in comparison of as deposited.     

Deposition of MgO films by pulsed mid-frequency magnetron sputtering

MgO films were deposited by pulsed mid-frequency magnetron sputtering from metallic targets in the mixture of Ar and O₂ gas. The surface morphology, crystalline structure, and optical properties were characterized by using atomic force microscopy (AFM), X-ray diffraction (XRD), and spectroscopic ellipsometry, respectively. The secondary electron emission coefficients of MgO films were measured by using a self-made apparatus in He gas. A pronounced hysteresis phenomenon of target voltage, current, and deposition rate with increasing and decreasing O₂ flow rate was observed. The structure of films deposited at a metallic mode changes from Mg phase to the mixed Mg and MgO phase, and the films have a very rough surface. All the films deposited at oxide mode have high transparency and smooth surface, and show (2 2 0) preferred orientation growth. The refractive index and extinction coefficient at a wavelength of 670 nm for MgO films deposited at oxide mode with a O₂ flow rate of 3 sccm are 1.698 and 1.16×10⁻⁴, respectively. The secondary emission coefficient at a E/p of 57.8 V/(cm Torr) for MgO films deposited at a O₂ flow rate of 3 sccm is 0.16, which is higher than that of MgO films deposited by e-beam evaporation.     

Preparation and characterization of alkyl sulfate and alkylbenzene sulfonate surfactants/TiO2 hybrid thin films by the liquid phase deposition (LPD) method

Hybrid titanium oxide thin films containing surfactants, sodium dodecyl benzylsulfonate and sodium dodecyl sulfate, have been prepared by a novel liquid-phase deposition method. It is a new attempt to prepare organic–inorganic hybrid thin film by this method which usually be applied in preparing metal oxide thin film before. The two kinds of surfactants/TiO₂ hybrid thin films were characterized by means of FT-IR, SEM, XRD, fluorescence X-ray, ICP–AES and Raman spectroscopy, and showed noticeable differences in surface top view and particle diameter, cross-section image and thickness, deposited amount of Ti, XRD patterns and Raman shift. The reasons giving rise to above differences of the two kinds composite thin films has been discussed. The deposition mechanism of organic–inorganic hybrid thin film has been also presumed. The use of this processing parameter may open up a new way to the preparing of the organic–inorganic hybrid thin film.     

Direct current magnetron sputter-deposited ZnO thin films

Zinc oxide (ZnO) is a very promising electronic material for emerging transparent large-area electronic applications including thin-film sensors, transistors and solar cells. We fabricated ZnO thin films by employing direct current (DC) magnetron sputtering deposition technique. ZnO films with different thicknesses ranging from 150 nm to 750 nm were deposited on glass substrates. The deposition pressure and the substrate temperature were varied from 12 mTorr to 25 mTorr, and from room temperature to 450 °C, respectively. The influence of the film thickness, deposition pressure and the substrate temperature on structural and optical properties of the ZnO films was investigated using atomic force microscopy (AFM) and ultraviolet-visible (UV-Vis) spectrometer. The experimental results reveal that the film thickness, deposition pressure and the substrate temperature play significant role in the structural formation and the optical properties of the deposited ZnO thin films.