The morphology and crystalline region distribution of polyacrylonitrile nanofibers prepared by electrospinning

The effects of electrospinning parameters in a wider range on the morphology and diameters of polyacrylonitrile (PAN) fibers are studied in detail. The fibers’ diameter increases from 288 to 3469 nm swiftly with the increasing PAN concentration. With the increasing voltage or prolonging gap distance, the diameter increases primarily and decreases later. The combined effects of surface tension, splitting and stretching, electric force, viscosity, and solvent volatilization are the main reasons. Ultrasonic etching method, Atomic force microscope (AFM), Scanning electron microscope (SEM) and X-ray diffraction (XRD) technology have been utilized to verify the nature structure of electrospun PAN fibers. Combining all the results, it is deduced that there are many grooves arranging nearly perpendicular to the fiber axis on the surface of electrospun PAN fibers. The thickness of relative ordered region is 40 to 190 nm and the thickness of amorphous region is 20 to 35 nm.     

Synthesis and properties of ZnO nanofibers prepared by electrospinning

ZnO nanofibers were prepared from zinc acetate/polyvinyl alcohol (PVA) by electrospun method. The morphological features, crystallinity, mechanical and optical properties of the ZnO nanofibers were studied. The results show the specific surface area of the ZnO nanofibers was influenced by the electrospun conditions. The specific surface area reached 389.7 m²g⁻¹ as the average diameter was 232 nm. The XRD date reveals the nanofibers consist of a single phase of well-crystallized ZnO with hexagonal structure. The elastic modulus of a single ZnO nanofiber was also characterized by nano-scale three-point bending test.     

Effect of CNT incorporation on PAN/PPy nanofibers synthesized by electrospinning method

In this study, carbon nanotubes (CNTs) added polyacrylonitrile/polypyrrole (PAN/PPy) electrospun nanofibers were produced. Average diameters of the nanofibers were measured as 268 and 153 nm for 10 and 25 wt% of PPy contents, respectively. A relatively higher strain to failure values (23.3%) were observed for the low PPy content. When as-grown CNTs (1 and 4 wt%) were added into the PAN/PPy blends, disordered nanofibers were observed to form within the microstructure. To improve the interfacial properties of CNTs/PAN/PPy composites, CNTs were functionalized with H₂SO₄/HNO₃/HCl solution. The functionalized CNTs were well dispersed within the nanofibers and aligned along the direction of nanofibers. Therefore, beads formation on nanofibers decreased. The impedance of the nanofibers was found to decrease with the PPy content and CNT addition. These nanofibers had a great potential to be used as an electrochemical actuator or a tissue engineering scaffold.     

Polymer nanofibers assembled by electrospinning

Electrospinning is a process by which polymer nanofibers (with diameter lower than 100 nm and lengths up to kilometres) can be produced using an electrostatically driven jet of polymer solution (or polymer melt). Simple alignment of electrospun nanofibers constructs unique functional nanostructures such as nanotubes and nanowires. Significant progress has been made in this area throughout the past few years and this technology has been exploited to a wide range of applications. Most of the recent work on electrospinning has focused either on trying to understand deeper the fundamental aspects of the process in order to gain control of nanofiber morphology, structure, surface functionality, and strategies for assembling them or on determining appropriate conditions for electrospinning of various polymers and biopolymers.     

静电纺丝法制备MgO纳米纤维

以聚乙烯醇(PVA)作为络合剂与醋酸镁反应制得前驱体，采用静电纺丝法制得聚乙烯醇(PVA)／醋酸镁复合纤维，经焙烧后得到分布均匀、具有较高比表面积和多孔结构的。MgO纳米纤维．对所制得的纳米纤维的结晶度、纯度和表面形貌，分别采用X射线粉末衍射、差热一热重分析(TG-DTA)、红外光谱(IR)、扫描电镜(SEM)等分析测试手段进行了表征．结果表明，煅烧温度对纳米纤维的结晶度和形貌有很大影响．     

Fibroin nanofibers production by electrospinning method

Silk fibroin, which has many characteristic properties such as low inflammation reaction, biodegradation, suppleness, good antithrombogenic details, biocompatibility and high tensile strength is a very good candidate for biomedical applications. Electrospinning procures high surface area, porous, nanofiber dimension fiber generation, which is a plain method. An experimental study was carried out to produce nanofiber structure from silk fibroin by electrospinning and the electrospinning parameters for the spinning of uniform, continuous and silk fibroin fibers were optimized. As a result, the effect of variables of concentration, distance and applied voltage on the strength, thickness, surface structure, fiber diameter of nanomaterial was investigated. Then, in vitro cell viability of the silk fibroin mat was analyzed. It was seen that the strength, mat thickness, and fiber diameter increased with solution concentration rise. It was found that the values of the fiber diameter and tensile strength decreased with increasing distance. It was determined that the effect of distance varies depending on the concentration in the mat thicknesses. The tensile strength was affected inversely proportional the applied voltage rises and distance. It was found that the fiber diameter values decreased together with increasing applied voltage. At cell viability of silk fibroin mat was occurred high cell viability after 24 h, but it was obtained low cell viability at the 48th h.     

Humic-makeup approach for simultaneous functionalization of polyacrylonitrile nanofibers during electrospinning process,and dye adsorption study

A useful methodology is represented to functionalize polyacrylonitrile nanofibers by using humic acid as a makeup agent in electrospinning process. Both morphology and surface chemistry of polyacrylonitrile nanofiber mats were understood to be influenced by incorporation of humic acid into the structure. Physicochemical changes were evidenced by Fourier transform infrared spectroscopy, scanning electron microscope, and surface charge measurements. Unlike some anionic dyes (i.e., methyl orange, methyl red, and Congo red), there was an enhancement in crystal violet (a cationic dye) adsorption after incorporation of humic acid. The Langmuir model fitted well to crystal violet data, and monolayer adsorption capacity was calculated as 81.6 mg/g (r² = 0.998).     

Durable antibacterial Ag/polyacrylonitrile (Ag/PAN) hybrid nanofibers prepared by atmospheric plasma treatment and electrospinning

Durable antibacterial Ag/polyacrylonitrile (Ag/PAN) hybrid nanofibers were prepared by atmospheric plasma treatment and electrospinning. Atmospheric helium plasma treatment was first used to reduce the AgNO₃ precursor in pre-electrospinning solutions into metallic silver nanoparticles, followed by electrospinning into continuous and smooth nanofibers with Ag nanoparticles embedded in the matrix. SEM, TEM, and EDX spectra were used to study the structure and surface elemental composition of the nanofibers. Silver nanoparticles, with diameters ranging between 3 and 6 nm, were found to be uniformly dispersed in the nanofiber matrix. The Ag/PAN nanofibers exhibited slow and long-lasting silver ion release, which provided robust antibacterial activity against both Gram-positive Bacillus cereus and Gram-negative Escherichia coli microorganisms.     

A novel and convenient preparation of antibacterial polyacrylonitrile nanofibers via post-modification using nitrile click chemistry and electrospinning

An efficient, novel and convenient method for the synthesis of modified polyacrylonitrile (PAN) with antibacterial property is reported. The modification of PAN was prepared by a nitrile click chemistry reaction with sodium azide (NaN₃) and silver nitrate (AgNO₃) as catalyst to yield antibacterial polymeric materials with 5-vinyltetrazole units. The results showed that 5-vinyltetrazole units had coordinated with silver ion (Ag⁺). Through the electrostatic spinning technology, the post-modification PAN nanofibers (PAN–Ag⁺ nanofibers) were prepared and the fibers were tested for their antimicrobial properties by the bacterial infection experiment. Afterwards, the antibacterial and stable performance of different proportions of silver ions in PAN nanofibers has been compared. The PAN–Ag⁺ nanofibers are characterized for mechanical and thermomechanical properties, structural analysis, appearance characteristics, as well as the antibacterial properties. And the nanofibers exhibit marvelous chemical stability according to the thermogravimetric analysis. When at 800 °C, the PAN decomposed about 60%, while the decomposition of the PAN–Ag⁺s was 40%. Based on the bacterial infection experiment, PAN–Ag⁺ nanofibers’ antibacterial properties were stronger with the increase of silver ions, such as the number of bacteria clone was smaller and the bacteriostatic ring was larger. Hence, with combination of silver ions, the final polymers show strong antimicrobial properties.     

Interface hydrogen-bonded core-shell nanofibers by coaxial electrospinning

Core-shell nanofibers were prepared by coaxial electrospinning technology,with poly(ethylene oxide) (PEO) as the core while poly(acrylic acid) (PAA) as the shell.PEO and PAA can form polymer complexes based on hydrogen bonding.In order to avoid forming strong hydrogen bonding complexes at nozzle and blocking spinning process,a polar aprotic solvent,N,N-dimethylformamide (DMF),was selected to dissolve PEO and PAA respectively.SEM,TEM and DSC were utilized to characterize the morphology and structure of PEO-PAA core-shell nanofibers.FTIR spectra demonstrated that hydrogen bonding was formed at the core-shell interface.In addition,the PAA shell of the nanofibers can be cross-linked by ethylene glycol (EG) under heat treatment,which increases the stability and extends the potential applications in aqueous environment.     

ZnO纳米纤维的静电纺丝及其光催化性能的研究

以聚乙烯醇溶液为络合剂与醋酸锌反应制得前驱体溶液,采用静电纺丝法制备PVA/Zn(Ac)2复合纳米纤维,经过高温煅烧得到直径为100 nm的ZnO纳米纤维,采用差热-热重分析、红外光谱分析、X射线粉末衍射分析及扫描电镜等手段对其进行了表征.光催化降解酸性品红溶液的实验结果表明,太阳光照65 min使质量浓度为45 mg/L酸性品红水溶液的脱色率达93%;另外,重复使用ZnO纳米纤维4次之后,其光催化降解率仍能达到70%以上.这充分说明ZnO纳米纤维具有良好的光催化性能.     

Functionalized carbon nanotube/polyacrylonitrile composite nanofibers: fabrication and properties

The functionalized multi‐walled carbon nanotubes (f‐MWCNTs) were obtained by Friedel–Crafts acylation, which introduced aromatic amine groups onto the sidewall. And the grafted yield was adjusted by controlling the concentration of the catalyst. The composite solutions containing f‐MWCNTs and polyacrylonitrile (PAN) were then prepared by in‐situ or ex‐situ solution polymerization. The resulting solutions were electrospun into composite nanofibers. In the in‐situ polymerization, morphological observation revealed that f‐MWCNTs was uniformly dispersed along the axes of the nanofibers and increased interfacial adhesion between f‐MWCNTs and PAN. Furthermore, two kinds of f‐MWCNTs/PAN composite nanofibers had a higher degree of crystallization and a larger crystal size than PAN nanofibers had, so the specific tensile strengths and modulus of the composite nanofibers were enhanced. And the thermal stability of f‐MWCNTs/PAN from in‐situ method was higher than that of ex‐situ system. When the f‐MWCNTs content was less than 1 wt%, the specific tensile strengths and modulus of nanofibers were enhanced with increase in the amounts of f‐MWCNTs, and f‐MWCNTs/PAN of in‐situ system provided better mechanical properties than that of ex‐situ system. Copyright © 2010 John Wiley & Sons, Ltd.     

Production of aligned helical polymer nanofibers by electrospinning

A new and simple electrospinning method has been developed for producing aligned helical polymer nanofibers. Aligned helical polycaprolactone (PCL) nanofibers were prepared by this method. The helical fibers were collected by a tilted glass slide. The morphology and loop diameters of the helical structures are dependant on the PCL solution concentration and the loop diameters are in the range of 6.9-14.9 μm for the concentration range of 4.7%-10%. The three-dimensional helical structures were obtained at the high solution concentration of 10%. These helical structures were formed by jet buckling due to mechanical instability when hitting collector surface. Formation of the helical structures is dependent on the obliquity of the tilted glass slide and distance away from the syringe needle. The converging electrical field generated by a tip collector plays an important role in the alignment of the helical structures.     

Large-scale synthesis of tungsten oxide nanofibers by electrospinning

We show in this communication that large-scale synthesis of orthorhombic WO3 nanofibers can be obtained via a simple electrospinning method. The morphology and the crystal structure are investigated by scanning electron microscopy (SEM), transmission electron microscopy (TEM), FTIR, X-ray diffraction patterns (XRD) and X-ray photoelectron spectra (XPS) spectra. SEM and TEM images showed that the diameter of the obtained WO3 nanofibers is between 100 and 500 nm. The structure of the obtained WO3 nanofibers was characterized by FTIR, XRD, and XPS spectra. The photoluminescence of the obtained WO3 nanofibers were also investigated.     

Magnetic Fe doped ZnO nanofibers obtained by electrospinning

We demonstrate structural and room temperature magnetic properties of Fe doped ZnO nanofibers (NFs) obtained by electrospinning followed by calcination. The observed NFs, formed from crystalographically oriented, approximately 4.5?nm particles conglomerates, were approximately 200?nm in diameter. The reported synthesis of room temperature ferromagnetic Fe doped ZnO NFs is both facile and economical, and is therefore suggested as a generic method of fabricating biocompatible magnetic materials. The major substrates selected for the NFs synthesis (Zn, Fe) comprised of relatively low toxicity materials. Incorporating 10% Fe into ZnO does not modify the wurtzite crystal structure of the host material. No evidence of impurity phase was detected by either X-ray or electron diffraction. Magnetometry studies and Magnetic Force Microscopy imaging reveal a local ferromagnetic order that persists up to room temperature. We suggest that the observed phenomenon is either due to a mechanism mediated by presence of oxygen vacancies and/or is related to iron-rich precipitates.     

Polysulfone nanofibers prepared by electrospinning and gas/jet-electrospinning

Polysulfone nanofibers were prepared by electrospinning. The electrospinning equipment was designed in a new way, wherein the spinneret was combined with a gas jet device. The intrinsic viscosity of the used polysulfone was 0.197 dL/g in dimethyl acetamide, which was also the solvent in electrospinning. The gas used in this gas jet/electrostatic spinning was nitrogen. The relationship between the process parameters and the average diameter of polysulfone nanofibers was investigated. The main process parameters studied in this work were the voltage, the flow rate of the spinning fluid, the distance between the spinneret and the nanofiber collector and the temperature in the spinning chamber. The other important factors determining the nanometer diameter were the spinning fluid properties including its viscosity, surface tension and electrical conductivity. The average diameter and the diameter distribution of electrospinning nanofibers were measured experimentally by using scanning electron microscopy. The diameter of polysulfone nanofibers prepared by the gas jet/electrostatic spinning was in the range 50–500 nm. It was found that the diameter of nanofibers mainly depended on high voltage, the gap between the spinneret and the collector and the concentration of polymer solutions. It is concluded that the gas-jet/electrospinning is a better method than the conventional electrospinning, in that it makes the nanofibers finer and more uniform and exhibits higher efficiency in the process of electrospinning. __________ Translated from Acta Polymerica Sinica, 2005, (5) (in Chinese)     

静电纺丝法制备纳米抗菌纤维的研究进展

纳米抗菌材料是防止细菌等致病微生物对人们生产、生活的破坏而发展起来的一类新型材料.在纳米抗菌材料的众多制备方法中,静电纺丝是一种成本低,工艺可控的技术,制备的纳米纤维具有比表面积大、孔隙率高、纤维均匀等特点.本文作者首先简述了静电纺丝技术以及该技术制备纳米抗菌纤维材料的特点;接着按照菌剂种类不同,对静电纺丝技术制备的抗菌纤维材料进行归类,将其分为无机抗菌纤维材料、天然抗菌纤维材料和复合抗菌纤维材料3类,并对其研究进展进行了评述;最后对静电纺丝技术制备纳米抗菌纤维的研究现状进行了总结与展望.     

Investigation of physicochemical properties of CuSn-based PAN nanofibers prepared via electrospinning method

Copper-tin (CuSn) nanomaterials have been receiving substantial attention due to their excellent thermal, electrical, and optical properties. However, how such properties are affected based on heat treatment temperature and chemical composition of copper and tin is still not very well understood. In this paper, CuSn nanofibers were fabricated by electrospinning a precursor solution of polyacrylonitrile, copper, and tin. Calcination temperatures were selected using thermogravimetric/differential thermal analysis (TG/DTA) and Fourier transform infrared (FT-IR) results. Analytical techniques such as scanning electron microscopy (SEM), energy dispersive spectrometry (EDS), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and ultraviolet photoelectron spectroscopy (UPS) were employed to investigate the physicochemical properties of the CuSn nanofibers. SEM images and EDS revealed the formation of pores on the nanofibers and high concentrations of tin were in the core, while copper was located on the surface. XRD results confirmed the monoclinic phase of Cu₆Sn₅ for the CuSn nanofibers because peaks for diffraction angles at 27.6°, 53.4°, and 60.0° were observed. XPS results showed that Cu―C and Sn―C bonds occur at binding energies around 932 and 484 eV, respectively. The work function of the CuSn NF heat treated at 150°C was calculated from the UPS spectra, and the value was 4.19 eV.     

Dye,fluorophores and pigment coloration of nanofibers produced by electrospinning

Polymeric nanofibers produced by the electrospinning technique are widely used in industrial scale production. Nanofibers chiefly find applications in filtration media and active–barrier surfaces for medical, biological, and military applications. In such applications, the quantity and the uniformity of the nanofibers distribution play a leading role in the product characteristics. For this reason, there is considerable interest regarding the nanofibers recovering quantification and simplification of the qualitative analysis. With the aim to improve and simplify the nanofibers relevability, a coloration approach for nanofibers has been designed and tested. The coloration has been carried out by organic dyes, pigments, and organic fluorophores and the consequent nanofibers' color has been analyzed by optical analysis, colorimetry, and spectroscopy. The coloration obtained by different dyes has been compared and their effect on the nanofibers relevability has been investigated. Moreover, the leading role of the light scattering phenomenon on the nanofiber coloration efficacy has been investigated by comparing the coloration response of nanofibers and film samples on equal terms of dye content. The study has been carried out using polyamide‐6 (PA6) as the testing polymer but the recovering quantification, the coloration approach, and the interaction between light and nanofibers can be extended to all the electrospinnable polymers. Copyright © 2008 John Wiley & Sons, Ltd.