交换时间对离子交换法合成谷氨酸/锌铝层状双氢氧化物的结构和热稳定性的影响

采用离子交换法实现了谷氨酸(Glu)插层到ZnAl层状双氢氧化物(ZnAl-LDH)中而形成Glu/ZnAl-LDH纳米复合材料,并用X射线衍射(XRD)、傅里叶变换红外(FT-IR)光谱、透射电子显微镜(TEM)以及热失重-差热(TG-DTA)分析等测试技术,研究了交换时间对Glu/ZnAl-LDH纳米复合材料结构的影响。发现当交换时间为1d时,Glu/ZnAl-LDH纳米复合材料粒子的结晶度好,Glu分子均以垂直形式插入,此时Glu在层间达到交换平衡。当交换时间为2d时,部分Glu开始以水平方式插入ZnAl-LDH纳米材料层间。但当交换时间进一步延长时,ZnAl-LDH纳米材料的结构发生部分坍塌,而且ZnAl-LDH纳米材料在微酸性的Glu溶液中发生部分溶解而使其六边形的结构出现破损。由于Glu插入ZnAl-LDH纳米复合材料层间后,其稳定性得到提高,因此,ZnAl-LDH纳米材料可以作为优良的生物分子的载体和储存器。     

机械混炼过程对天然橡胶/有机蒙脱土纳米复合材料结构的影响

采用机械混炼插层法制备天然橡胶(NR)/有机蒙脱土(OMMT)纳米复合材料,研究混炼过程对复合材料结构的影响。结果表明,剪切作用越强并不越有利于大分子链的插层,当辊距为3 mm时,适当增加薄通的次数,有益于分子链插入蒙脱土层间。当薄通次数达到40次时,可形成剥离型的纳米复合材料。且在共混过程中加入偶联剂,可使得蒙脱土与橡胶间的化学交联的比例提高,从而改善复合材料的物理机械性能和热氧老化性能。     

聚苯乙烯/多面体倍半硅氧烷(POSS)纳米复合材料

本研究通过Wittig反应合成了同时含有金属和双键的新型磁性多面体齐聚倍半硅氧烷POSS1(Fc-CH=CH-C6H6-(C4H9)7Si8O12,Fc:Ferrocene),并通过FTIR1、H-NMR1、3C-NMR2、9Si-NMR对其化学结构进行了表征。将其加入苯乙烯中通过自由基本体聚合制备了聚苯乙烯/POSS1纳米复合材料。XRD和TEM结果表明,POSS1在纳米材料中含量为1%(wt)和3%(wt)时可达分子级分散,而含量为5%(wt)时部分POSS1以晶体形式存在。热失重分析表明PS/POSS1纳米材料较纯PS热稳定性增加,含5%(wt)POSS1的纳米复合材料起始分解温度比纯PS的约提高了19℃。PS/POSS1纳米材料的玻璃化转变温度较纯PS明显提高。     

sPS/PA6/蒙脱土纳米复合材料的制备与性能

讨论了间规聚苯乙烯 (sPS) 尼龙 6(PA6) 磺化间规聚苯乙烯 (SsPS H) 蒙脱土纳米复合材料的制备技术和新材料的结构与性能特征 .蒙脱土经层间改性处理后 (MTN) ,可分别将SsPS H和aPS(无规聚苯乙烯 )插入其纳米层间 ,制备出插层型纳米复合物MTN SsPS和MTN aPS .在sPS/PA6/SsPS H三组分共混体系中加入MTN SsPS或MTN aPS ,进行四组分熔融共混即可制备出sPS/PA6/SsPS H/蒙脱土纳米复合材料 .TEM测定证实了蒙脱土在基体中的层厚分布约为 5 0nm .此外 ,采用DSC、DMA、XRD及力学性能测试仪等现代分析方法对sPS/PA6/SsPS H/蒙脱土纳米复合材料的结构与性能进行了详细研究 .研究结果表明这种纳米复合材料具有优良的综合性能     

甲氨蝶呤/层状双金属氢氧化物的粒径调控及缓释性能研究

在乙醇-水混合体系中, 以氨水为沉淀剂共沉淀合成了甲氨蝶呤/层状双金属氢氧化物(MTX/LDH)纳米复合物, 首次采用控制沉淀剂滴加速率的方式来调控其粒径. 利用X-射线衍射(XRD)、透射电镜(TEM)和红外光谱(FT-IR)等表征手段, 对其结构及形貌进行了表征. 研究表明: MTX分子以单层倾斜方式插入LDH层间, 随着滴加速率不同, MTX在层间的倾斜角度发生了变化; 沉淀剂滴加速率对产物的结晶度、粒径和层间排列方式都有影响, 当沉淀剂滴加速率为0.100 mL/s时, 得到的MTX/LDH纳米复合物的结晶度最高, 粒径最大. 在磷酸缓冲液中考察了不同粒径MTX/LDH纳米复合物的缓释性能, 结果表明: 小粒径的MTX/LDH纳米复合物的载药量要高于大粒径的; 当MTX阴离子在层间的倾斜角度相似时, 粒径小的粒子释放速率较慢, 缓释效果优于粒径大的. 尤为重要的是我们探索出一条保证复合物阴离子在层间的倾斜角度相似的情况下, 制备不同粒径纳米复合物的新途径.     

聚合物/粘土纳米复合材料中的粘土有机化

回顾了聚合物/粘土纳米复合材料中所用粘土的有机化方法与有机粘土的热稳定性,及其对复合材料性能的影响,指出在聚合物/粘土复合材料中粘土片层间距的变化同样有可能受到层间插层剂构象变化的影响、聚合物/粘土纳米材料的长期热氧稳定性与热失重结果可能不一致。     

甲氨蝶呤/层状双金属氢氧化物的性能调控及细胞生物实验研究

在乙醇-水混合体系中,以氨水为沉淀剂共沉淀合成了甲氨蝶呤/层状双金属氢氧化物(MTX/LDH)纳米复合物,采用控制水热处理时间的方式来调控其性能。利用X-射线衍射(XRD)、透射电镜(TEM)和红外光谱(FT-IR)等表征手段,对其结构及形貌进行了表征。研究表明:MTX分子以单层倾斜或垂直方式插入LDH层间,随着水热处理时间的不同,MTX在层间的倾斜角度发生了变化;水热处理时间对产物的结晶度、粒径和层间排列方式都有影响,当水热处理时间为12h时,得到的MTX/LDH纳米复合物的结晶度最高,单分散性最好。在磷酸缓冲液中考察了MTX/LDH纳米复合物的缓释性能,结果表明样品均呈现出良好的缓释性能,释放速率先快后慢。重点考察了这几种MTX/LDH纳米复合物作用于肺癌细胞A549的细胞生物实验,研究表明这几种复合物对肺癌细胞A549都具有良好的抑制作用,其效果与纳米复合物的单分散性和粒径有密切的关系,单分散性越好,粒径分布越均匀,对A549癌细胞的抑制效果越好。     

激光烧结制备尼龙12/累托石纳米复合材料

将有机累托石与尼龙12粉末混合,采用激光烧结(SLS)技术制备了尼龙12累托石纳米复合材料,这是一种使纳米复合材料的制备与材料的成型同时进行的方法.利用X射线衍射(XRD)、红外光谱(FTIR)、扫描电镜(SEM)等手段对复合材料的结构进行了表征,并对其力学性能及热性能进行了研究.结果表明,尼龙12分子在激光烧结过程中插入到累托石层间,形成的复合材料在拉伸强度、弯曲强度、冲击强度等力学性能及热稳定性能方面均优于尼龙12烧结试样.     

聚酰亚胺/绢云母复合材料的制备及表征

首先采用加热和酸浸、硝酸锂处理、十六烷基三甲基溴化铵(HDTMAB)阳离子交换等多步反应制备了有机绢云母,随后通过原位聚合插层法合成了不同种类的聚酰亚胺(PI)/绢云母复合材料.研究了反应温度及有机阳离子HDTMAB加入量对绢云母改性效果的影响,采用X-射线衍射(XRD)、傅里叶变换红外光谱(FTIR)和扫描电子显微镜(SEM)对改性前后的绢云母进行了系统的分析.结果表明,改性反应温度为180℃,有机阳离子加入量为15倍的阳离子交换容量(CEC)时插层效果最理想,在此条件下,绢云母d002晶面间距从0.99 nm扩大到2.77 nm.通过XRD和高分辨透射电子显微镜(HRTEM)对复合材料的微观结构进行了研究,采用热重分析(TGA)和力学性能测试研究了复合材料的热性能,拉伸强度、杨氏模量和断裂伸长率.结果表明,用原样绢云母制备的PI/原样绢云母复合材料是一种简单物理混合物,而PI/有机绢云母复合材料是一种剥离型纳米复合材料,同时,有机绢云母含量为1%~7%的纳米复合材料在2θ=0.5°~10°的衍射角范围内,均没有出现明显的衍射峰,表明有机绢云母的d002晶面间距被扩大到4.42 nm以上.绢云母与PI质量比为5∶100时,PI/有机绢云母纳米复合材料的拉伸强度、杨氏模量、断裂伸长率是PI/原样绢云母复合材料相应值的1.79,1.40和1.83倍.纳米复合材料的T5(质量损失5%时的温度)随着有机绢云母含量的增加而显著提高,当有机绢云母含量为7%时,纳米复合材料的T5相比纯PI可提高36℃.     

聚氨酯/蒙脱土纳米复合材料的制备与性能研究

纳米复合材料由于其纳米尺寸效应 ,表面效应以及纳米粒子与基体界面间强的相互作用 ,具有优于相同组分常规复合材料的力学 ,热学等性能 ,引起了人们的广泛关注 .用纳米材料改性聚合物 ,制备纳米复合材料是获得高性能高分子复合材料的重要方法 ,采用较多的是插层复合法 ,可分为两类 ,一是单体预先插层于层状结构填料的晶片层间 ,然后聚合 ;二是聚合物溶液或熔体直接插层于层状结构填料的晶片层间 .聚氨酯 (PU)是由多异氰酸酯与多元醇通过加聚反应而形成的高聚物 ,其重复结构单元是氨基甲酸酯链段( R2 OCONHR1NHCOO) .PU弹性体具有耐磨…     

Hydrothermal Synthesis of Glutamic Acid/Layered Double Hydroxide Compounds

In this article, glutamic acid (Glu) was intercalated into the Zn-Al layered double hydroxides (Zn-Al LDHs) by hydrothermal method. The influence of the molar ratio of Zn/Al/Glu (R values for short), the aging time, and the pH value of the washing solution was systematically studied. The resulting Glu-LDH compounds were characterized by x-ray diffraction (XRD), fourier transform infrared spectroscopy (FTIR), and scanning electron micrograph (SEM). The XRD results showed that the relative diffraction intensity first increased then decreased as the R value and the pH value of the washing solution increased. Moreover, the crystallinity degree decreased gradually with the increase of the aging time. The absorption peaks attributed to the stretch of (R-COO^?) were observed in the FTIR spectra. SEM graphs indicated that the morphology of the particles was largely influenced by the synthesis conditions.     

聚乙烯/石墨层间化合物热降解过程的TG-FTIR研究

将含磷化合物插层石墨层间化合物(GIC)用于聚乙烯(PE)的阻燃,采用氧指数(LOI)方法评价了PE/GIC的阻燃性能,并采用热分析-红外光谱联用技术(TG-FTIR)研究了PE/GIC的热降解过程,探讨了GIC的阻燃机理。研究表明,不同含磷化合物插层GIC阻燃聚乙烯的氧指数有显著差别,其中以多聚磷酸铵-GIC的阻燃效果较好,氧指数较高。TG-FTIR研究结果表明,GIC并未显著影响PE的热降解方式,但由于GIC体积膨胀所发生的氧化还原反应导致部分PE热降解提前并发生热氧化降解,促进了后期成炭的石墨化过程。     

牛黄酸及水杨酸系药物对镁铝层状复合氢氧化物的插层组装

通过XRD和IR表征对镁铝层状复合氧氧化物(LDH)与水杨酸、乙酰氨基酚、乙酰水杨酸,以及谷氨酸、色氨酸、牛黄酸反应产物的比较分析,研究了不同药物对有关组装方式的适宜性.结果表明水杨酸类药物均可通过离子交换组装到LDH层间,晶胞参数c由2.3893 nm依次增大为2.4024、2.4110和2.4111nm,通道高度h由0.3194 nm增大为0.3238、0.3267和0.3268 nm;通过离子交换能将谷氨酸组装到LDH层间,产物的IR吸收、热分解行为及TEM形貌与前体有明显区别,晶胞参数c由2.3765nm增大为2.3851nm,h由0.3152nm增大为0.3180nm;共沉淀法适宜制备LDH-牛黄酸插层复合物,但简单的离子交换不能使色氨酸与LDH有效复合.     

醇水介质中共沉淀法制备甲氨蝶呤/层状双氢氧化物纳米材料的研究

采用乙醇-水混合溶液为溶剂,以NaOH为沉淀剂制备了甲氨蝶呤(MTX)-镁铝层状双氢氧化物(Mg-Al-LDH)纳米复合材料,利用X-射线衍射(XRD)、透射电镜(TEM)和傅里叶变换红外(FT-IR)光谱等表征手段,对其结构及形貌进行了系统研究.研究表明,与传统的水溶液共沉淀法相比,醇水共沉淀法制备的MTX/LDH纳...     

Structure and thermal decomposition of sulfated β-cyclodextrin intercalated in a layered double hydroxide

The sodium salt of hexasulfated β-cyclodextrin has been synthesized and intercalated into a magnesium-aluminum layered double hydroxide by ion exchange. The structure, composition and thermal decomposition behavior of the intercalated material have been studied by variable temperature X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), inductively coupled plasma emission spectroscopy (ICP), and thermal analysis (TG-DTA) and a model for the structure has been proposed. The thermal stability of the intercalated sulfated β-cyclodextrin is significantly enhanced compared with the pure form before intercalation.     

Thermoanalytical Investigation of Formamide Intercalated Kaolinites Under Quasi-isothermal Conditions

The thermal behaviour of fully and partially expanded kaolinites intercalated with formamide has been investigated in nitrogen atmosphere under quasi-isothermal heating conditions at a constant, pre-set decomposition rate of 0.20 mg min^–1 . With this technique it is possible to distinguish between loosely bonded (surface bonded) and strongly bonded (intercalated) formamide. Loosely bonded formamide is liberated in an equilibrium reaction under quasi-isothermal conditions at 118°C, while the strongly bonded (intercalated) portion is lost in an equilibrium, but non-isothermal process between 130 and 200°C. The presence of water in the intercalation solution can influence the amount of adsorbed formamide, but has no effect on the amount of the intercalated reagent. When the kaolinite is fully expanded, the amount of formamide hydrogen bonded to the inner surface of the mineral is 0.25 mol formamide/mol inner surface OH group. While the amount of surface bonded formamide is decreasing with time, no change can be observed in the amount of the intercalated reagent. With this technique the mass loss stages belonging to adsorbed and intercalated formamide can be resolved thereby providing a complex containing only one type of bonded (intercalated) formamide.This revised version was published online in November 2005 with corrections to the Cover Date.     

Intercalation and functionalization of zinc hydroxide nitrate with mono- and dicarboxylic acids

The intercalation of ions derived from succinic, glutaric, and adipic acid into layered zinc hydroxide nitrate by ionic exchange reaction is reported. Different reaction conditions are investigated and the materials are characterized by powder X-ray diffraction, Fourier transform infrared spectroscopy, thermal analysis (simultaneous thermogravimetry and differential scanning calorimetry) and elemental analysis. The dicarboxylic acids can be grafted to the matrix slab by one carboxylate group and the second hydrated carboxylate group is hanging between the layers. Benzoate ions have also been intercalated by both ionic exchange reaction and stirring in acetonitrile. The two benzoate-intercalated materials exchange the organic moiety by sulfate ions if stirred in magnesium sulfate solution, but the sample obtained by anion exchange also allows the unusual incorporation of neutral magnesium sulfate in addition to free solvated sulfate ion. A schematic arrangement of the intercalated species between the layers is presented.     

Synthesis and Characterization of Poly(ethylene terephthalate)/Modified Lithium‐Aluminum‐Layered Double Hydroxide Nanocomposites Prepared Using In‐situ Polymerization

Layered double hydroxides are a type of layered stacked compound, which can be intercalated with organic‐molecule modifiers. An ion‐exchange process for layered double hydroxide (LDH) was used to intercalate water‐soluble sulfanilic acid salt (SAS) and dimethyl 5‐sulfoisopthalate (DMSI) into lithium aluminum layered double hydroxides (LiAl LDHs). In this work, a hydrothermal process was used to modify LiAl LDHs, and the modified LiAl LDHs were treated with either SAS or DMSI through an ion‐exchange process and were then intercalated using bis‐hydroxyethylene terephthalate (BHET). The results indicate that the modified LiAl LDHs improved the interlayer compatibility between the PET and LiAl LDH layers; thus, enabling the oligomer molecules to more easily enter the gallery of the LiAl LDH layers so that polymer chains could be included between the LDH layers during polymerization of the matrix. The better barrier, mechanical properties, and thermal stability of these new types of PET nanocomposites are discussed.     

聚苯乙烯/层状双金属氢氧化物纳米复合材料的制备与表征

由离子交换法制备4,4′-偶氮二(4-氰基戊酸)根(ACP)单独插层和ACP/对苯乙烯磺酸根(VBS)复合插层的层状双金属氢氧化物(LDH),再通过原位悬浮聚合制得聚苯乙烯(PS)/LDH纳米复合材料,对插层改性LDH和复合材料进行了结构和性能表征.X-射线衍射和元素分析表明ACP可以单独或与VBS一起插入到LDH层间.透射电镜和X-射线衍射分析表明采用ACP/VBS复合插层LDH与苯乙烯原位聚合得到的复合材料中LDH剥离程度高,熔融加工后LDH基本以纳米层板形式分散在PS基体中.LDH的引入可明显提高PS的热稳定性,而熔体流动性下降.