Raising the softening temperature of poly(vinylidene fluoride) gel electrolytes

Factors affecting the softening temperature of polymer gel electrolytes (PGEs) made from poly(vinylidene fluoride) (PVDF) have been investigated. The melting temperature transition has been found to rise with increased polymer concentration and salt concentration but reduced by solvent dielectric constant. The solvent dielectric constant was reduced by mixing propylene carbonate (PC) with the non-solvent phenyl propanol (PhP). The use of lithium salt bis(oxalate)borate (LiBOB) in place of lithium tetrafluroborote (LiBF₄) gives further enhancement to the softening temperature of PGEs. In all of those cases, there is an eventual trade-off between increased softening temperature and reduced ionic conductivity, in this fabricated gel electrolyte. Here, a variety of ways to tailor the properties of PGEs for different applications has been shown.     

The physical and electrochemical properties of poly(vinylidene chloride-co-acrylonitrile)-based polymer electrolytes prepared with different plasticizers

Lithium ion-conducting membranes with poly(ethylene oxide) (PEO)/poly(vinylidene chloride-co-acrylonitrile) (PVdC-co-AN)/lithium perchlorate (LiClO₄) were prepared by solution casting method. Different plasticizers ethylene carbonate (EC), propylene carbonate (PC), gamma butyrolactone (gBL), diethyl carbonate (DEC), dimethyl carbonate (DMC), and dibutyl phthalate (DBP) were complexed with the fixed ratio of PEO/PVdC-co-AN/LiClO₄. The preparation and physical and electrochemical properties of the gel polymer electrolytes have been briefly elucidated in this paper. The maximum ionic conductivity value computed from the ac impedance spectroscopy is found to be 3?×?10^?4 S cm^?1 for the EC-based system. From DBP-based system down to EC-based system, a decrease of crystallinity and an increase of amorphousity are depicted by X-ray diffraction technique, the decrease of band gap energy is picturized through UV–visible analysis, the decrease of glass transition temperature is perceived from differential scanning calorimetry plots, and the reduction of photoluminescence intensity is described through photoluminescence spectroscopy study at an excitation wavelength of 280 nm. Atomic force microscopic images of EC-based polymer electrolyte film show the escalation of micropores. Fourier transform infrared spectroscopy study supports the complex formation and the interaction between the polymers, salt, and plasticizer. The maximum thermal stability is obtained from thermogravimetry/differential thermal analysis, which is found to be 222 °C for the sample complexed with EC. The cyclic voltagram of the sample having a maximum ionic conductivity shows a small redox current at the anode, and cathode and the chemical stability is confirmed by linear sweep voltammetry.     

A phosphate additive for poly(ethylene oxide)-based gel polymer electrolytes

The influence of an organophosphosphate additive on poly(ethylene oxide) lithium bis(trifluoromethylsulfonyl)imide-based gel polymer electrolytes for secondary lithium battery applications is described. Tris(2-(2-methoxyethoxy)ethyl)phosphate, is compared to the well known gel-battery component, propylene carbonate, through a study of complex impedance analysis, differential scanning calorimetry, and limiting oxygen index combustion analysis. The conductivities of the gels at low concentrations of tris(2-(2-methoxyethoxy)ethyl)phosphate (1.9–4.2 mol%) are higher to those of propylene carbonate-based systems with the same concentration. Despite micro-phase separation at high concentrations of tris(2-(2-methoxyethoxy)ethyl)phosphate (7.0–14.9 mol%), the conductivities remain comparable to systems that use propylene carbonate. The addition of tris(2-(2-methoxyethoxy)ethyl)phosphate to poly(ethylene oxide) gives increased fire retardance, while the addition of propylene carbonate to poly(ethylene oxide) results in increased flammability.     

Piezoelectric properties of electron-irradiated poly (vinylidene fluoride)

Some of the piezoelectric constants of PVDF are strictly stress dependent. This behaviour is assumed to originate in a contribution of the interphase region between crystalline and amorphous phases to the piezoelectric effect in this material. This assumption is supported by the changes in piezoelectricity after irradiation with fast electrons. Such treatment causes crosslinking predominantly in the amorphous regions and, consequently, significant changes in the mobility of molecular electric moments. The piezoelectric constants become smaller upon irradiation, this being caused by a reduced permanent polarization, by increased mechanical stiffness, and by the reduced reorientability of the molecular electric moments in the interphase. One of the nonlinear piezoelectric coefficients changes its sign at a certain irradiation dose.     

Synthesis, characterization and electrochemical properties of poly(methyl methacrylate)-grafted-poly(vinylidene fluoride-hexafluoropropylene) gel electrolytes

A new comb-like copolymer, poly(vinylidene fluoride-co-hexafluoropropylene)-g-poly(methyl methacrylate), or [P(VDF-HFP)-g-PMMA], was successfully synthesized through grafting in situ formed PMMA to the P(VDF-HFP) backbone. The composition of the P(VDF-HFP)-g-PMMA copolymer was characterized by Fourier transform infrared spectroscopy (FTIR), thermal gravimetric analysis (TGA) and elemental analysis. X-Ray diffractometry (XRD) and differential scanning calorimetry (DSC) were used to examine the reduction in crystallinity of P(VDF-HFP) due to the anchoring of PMMA segments on it. Gel electrolyte membranes based on the resulting copolymer were prepared by the Bellcore process. The ionic conductivity of Li⁺ across the membranes and the related transference number were measured. A study of the interfacial stability between Li electrode and the P(VDF-HFP)-g-PMMA gel electrolyte was also conducted to evaluate the suitability of the P(VDF-HFP)-g-PMMA copolymer in rechargeable lithium and lithium-ion battery applications.     

The effect of hard segment content on ionic conductivity of poly(ether urethane)-based solid polymer electrolytes

To investigate the effect of hard segment content on ionic conductivities of poly(ether urethane) (PEU)-based solid polymer electrolytes (SPEs), PEUs containing 20, 40, 60, 80, and 100 wt.% of hard segment content were synthesized. Also we introduced polymer-in-salt system with ion-hopping mechanism contrary to traditional salt-in-polymer system with segmental motion mechanism and investigated the effect of hard segment of PEU on ionic conductivities by A.C. impedance, FT-IR, DSC, and SEM. And it could be known that hydrogen bonding of urethane group influenced the ionic conductivities of PEU-based SPE. PEU-based SPE containing 70 wt.% of salt and 20 wt.% of hard segment showed the highest ionic conductivity of 2.95 × 10⁻⁵ S/cm at room temperature.     

Radiation effects on poly(vinylidene fluoride)

Melt-crystallized poly(vinylidene fluoride)s (PVF₂) with different crystallization histories were irradiated with γ-rays within the range of irradiation doses 0–83 Mrad. The effects on the crystalline structure and mechanical properties have been measured, compared, and discussed. The degree of crystallinity of the samples was found to increase with radiation dose. The differential scanning calorimeter scans of the quenched samples indicate that there are two melting peaks, and that the area of the lower temperature peak increases while the area of higher temperature peak decreases with increasing dose. Yield stress and breaking stress for all samples are not significantly affected by irradiation but elongation at break is.     

Raman study of ion-molecules interaction in poly(methylmetacrylate)-based gel electrolytes

Gel electrolytes have been obtained, containing LiX (X=ClO₄, N(CF₃SO)₂, AsF₆) dissolved in a ethylene carbonate-propylene carbonate mixture and PMMA as polymeric matrix. Ionic conductivity has been measured, for two different lithium salts. The changes in the Raman spectra have been studied as a function of the polymer content, lithium salt concentrations and for different anions. Two satellite bands of the internal bending and stretching modes of ethylene carbonate appear in the spectrum of lithium containing samples, because of the cation-solvent molecule interaction. Paper presented at the 1st Euroconference on Solid State Ionics held in Zakynthos, Greece, Sept. 11–18, 1994     

The polymorphism of poly(vinylidene fluoride) IV. The structure of high-pressure-crystallized poly(vinylidene fluoride)

A detailed study of high-pressure-crystallized poly(vinylidene fluoride) has indicated that a mixture of low-melting phase II and high-melting phase I is present, rather than a new crystalline phase (phase III) as originally suggested.

The relative amounts of phase I and phase II resulting from crystallization under pressure are a function of pressure and the degree of supercooling. Pressure crystallization at 285°C and 5500 atm results in samples which were pure phase I with an increased melting point of 187°C.     

Vibrational and impedance spectroscopic analysis of poly(vinyl alcohol)-based solid polymer electrolytes

Solid polymer electrolytes based on poly(vinyl alcohol) (PVA) doped with NH₄Br have been prepared by the solution-casting method. The complex formation between the polymer and the salt has been confirmed by Fourier transform infrared spectroscopy. The highest conductivity at 303 K has been found to be of the order of 10⁻⁴ Scm⁻¹ for 25 mol% NH₄Br-doped PVA system. The ionic transference number of polymer electrolyte has been estimated by Wagner’s polarization method, and the results reveal that the conducting species are predominantly ions. Paper presented at the Third International Conference on Ionic Devices (ICID 2006), Chennai, Tamilnadu, India, Dec. 7–9, 2006.     

Structural and ionic conductivity studies of solid polymer electrolytes based on poly (vinylchloride) and poly (methylmethacrylate) blends

Thin film of poly (vinylchloride) and poly (methylmethacrylate) blend polymer electrolytes plasticized with a combination of DBP and Li₂SO₄ salts have been prepared by solution casting technique. The prepared films were subjected to a.c. impedance measurements as a function of temperature ranging from 304–373 K. The maximum conductivity at 304 K was found to be 1.24 × 10⁻⁸ S·cm⁻¹ for PVC-PMMA-Li₂SO₄-DBP (7.5-17.5-5-70 mole-%). Temperature dependence studies on the ionic conductivity in the PVC-PMMA-Li₂SO₄-DBP system suggest that the ion conduction follows the Williams-Landel-Ferry (WLF) mechanism, which is further confirmed by Vogel-Tamman-Fulcher (VTF) plots. XRD, FTIR, SEM and thermal studies revealed complex formation in.     

Conductivity, dielectric behaviour and thermal stability studies of lithium ion dissociation in poly(methyl methacrylate)-based gel polymer electrolytes

Thin films of poly(methyl methacrylate) (PMMA) with lithium triflate (LiCF₃SO₃) were prepared by using the solution-casting method with PMMA as the host polymer. Ionic conductivity and dielectric measurements were carried out on these films. The highest conductivity for polymer electrolyte with a ratio of 65:35 was found to be 9.88 × 10⁻⁵ S cm⁻¹, which is suitable for the production of mobile phone battery. Thermal gravimetric analysis was carried out to evaluate the thermal stability of the polymer electrolyte. The addition of salts will increase thermal stability of the polymer electrolyte.     

Polymer electrolytes based on copolymer of poly(ethylene glycol) dimethacrylate and imidazolium ionic liquid

Polymer electrolytes based on the copolymer of N-vinylimidazolium tetrafluoroborate (VyImBF₄) and poly(ethylene glycol) dimethacrylate (PEGDMA) have been prepared. Ethylene carbonate (EC) and LiClO₄ are added to form gel polymer electrolytes. The chemical structure of the samples and the interactions between the various constituents are studied by FT-IR. TGA results show that these polymer electrolytes have acceptable thermal stability, are stable up to 155 °C. Measurements of conductivity are carried out as a function of temperature, VyImBF₄ content in poly(VyImBF₄-co-PEGDMA), and the concentration of EC and LiClO₄. The conductivity increases with PEGDMA and EC content. The highest conductivity is obtained with a value of 2.90 × 10^? 6 S cm^? 1 at room temperature for VP1/EC(25 wt.%)–LiClO₄ system, corresponding to the LiClO₄ concentration of 0.70 mol kg^? 1 polymer.     

Thermal and electrochemical properties of poly(butylene sulfite)-based polymer electrolyte

Poly(butylene sulfite) (poly-1) was synthesized by cationic ring-opening polymerization of butylene sulfite (1), which was prepared by the reaction of 1,4-butanediol and thionyl chloride, with trifluoromethanesulfonic acid (TfOH) in bulk. The polymer electrolytes composed of poly-1 with lithium salts such as bis(trifluoromethanesulfonyl)imide (LiN(SO₂CF₃)₂, LiTFSI) and bis(fluorosulfonyl)imide (LiN(SO₂F)₂, LiFSI) were prepared, and their ionic conductivities, thermal, and electrochemical properties were investigated. Ionic conductivities of the polymer electrolytes for the poly-1/LiTFSI system increased with lithium salt concentrations, reached maximum values at the [LiTFSI]/[repeating unit] ratio of 1/10, and then decreased in further more salt concentrations. The highest ionic conductivity values at the [LiTFSI]/[repeating unit] ratio of 1/10 were 2.36?×?10^?4 S/cm at 80 °C and 1.01?×?10^?5 S/cm at 20 °C. On the other hand, ionic conductivities of the polymer electrolytes for the poly-1/LiFSI system increased with an increase in lithium salt concentrations, and ionic conductivity values at the [LiFSI]/[repeating unit] ratio of 1/1 were 1.25?×?10^?3 S/cm at 80 °C and 5.93?×?10^?5 S/cm at 20 °C. Glass transition temperature (T _g) increased with lithium salt concentrations for the poly-1/LiTFSI system, but T _g for the poly-1/LiFSI system was almost constant regardless of lithium salt concentrations. Both polymer electrolytes showed high transference number of lithium ion: 0.57 for the poly-1/LiTFSI system and 0.56 for the poly-1/LiFSI system, respectively. The polymer electrolytes for the poly-1/LiTFSI system were thermally more stable than those for the poly-1/LiFSI system.     

Kinetic of poly(vinylidene fluoride) defluorination under X-ray irradiation

Modification of the photoelectron and C KVV spectra during the long-term surface degradation of partially crystalline PVDF under simultaneous soft X-ray and electron irradiation are reported. Deep radiative carbonization brings about the formation of carbynoid structures (chain-like carbon) in the surface; as a result the shape of the electron emission spectra of carbon in the carbonized sample essentially differs from that of graphite and PVDF. Analysis of carbon core-level electron spectra via decomposition onto spectral components shows presence of partially (CH, CF) and fully (=C=, -C≡) carbonized units of polymeric chain thus pointing on two-step mechanism of polyme ric chain transformation from the initial to a carbynoid. Results of the mathematical modeling of the first step of the chain transformation show it to be a second order process.     

Polymer electrolytes based on poly(vinylidene fluoride-co-hexafluoropropylene) with crosslinked poly(ethylene glycol) for lithium batteries

The combination of a poly(ethylene glycol) (PEG) network and poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) copolymer chains is one of the most efficient means for modifying PVDF-HFP gel electrolytes. Previous preparations tend to introduce contamination into the polymer gel electrolyte because of irradiation, high temperature or the initiator needed for crosslinking which might result in the electrochemical degradation. In order to overcome the above disadvantages, a new method has been developed to successfully prepare the semi-interpenetrating polymer networks of PVDF-HFP based electrolytes with crosslinked diepoxy polyethylene glycol (DIEPEG). In this process, impurities are avoided because of a moderate reaction temperature at 50 °C and poly(ethylenimine) (PEI) as the crosslinking agent. Microporous films with various compositions are prepared and characterized. Thermal, mechanical, swelling and electrochemical properties, as well as microstructures of the prepared polymer electrolytes have been investigated using thermogravimetric analysis, electrochemical impedance spectroscopy, linear sweep voltammetry, and scanning electron microscopy. The results show that the blend polymer electrolyte with PVDF-HFP/PEI + DIEPEG (60:40 w/w) has an ionic conductivity of 2.3 mS cm^? 1 at room temperature in the presence of 1 M LiPF₆ in EC and DMC (1:1 w/w). All the blend electrolytes are electrochemically stable up to 4.8 V versus Li/Li⁺. The results reveal that this new method may be very promising for improving PVDF-HFP based electrolytes.     

Design of amphiphilic poly(vinylidene fluoride-<Emphasis Type="Italic">co</Emphasis>-hexafluoropropylene)-based gel electrolytes for high-performance lithium-ion batteries

Gel polymer electrolytes (GPE) based on electrospun polymer membranes, poly(vinylidene fluoride-co-hexafluoropropylene), grafted poly(poly(ethylene glycol) methyl ether methacrylate) (PVDF-HFP-g-PPEGMA), and poly(vinylidene difluoride-co-hexafluoropropylene) (PVDF-HFP) are prepared for lithium ion batteries by incorporating with 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide (BMITFSI). The uniform porosity and the compatibility of blend electrospun membranes avoiding the pore blocking are beneficial to enhance the electrolyte uptakes. The GPE based on the fibrous PVDF-HFP-g-PPEGMA/PVDF-HFP activated with 1 M LiTFSI (BMITFSI) show a maximum ionic conductivity of 2.3 × 10^?3 S cm^?1 at room temperature and electrochemical stability of up to 5.2 V. The Li/GPE/LiFePO₄ cells with GPE based on PVDF-HFP-g-PPEGMA/PVDF-HFP blend electrospun membrane deliver specific capacities of 163, 141, and 125 mAh g^?1 at 0.1, 0.5, and 1C rates, respectively, and remains well after 50 cycles for each rate. Therefore, the novel GPE have been demonstrated to be suitable for lithium-ion battery applications.     

Dielectric and thermal features of zinc ion conducting gel polymer electrolytes (GPEs) containing PVC / PEMA blend and EMIMTFSI ionic liquid

A new series of gel polymer electrolytes (GPEs) based on an optimized composition of polymer blend-salt matrix [poly(vinyl chloride) (PVC) (30 wt%) / poly(ethyl methacrylate) (PEMA) (70 wt%): 30 wt% zinc triflate Zn(CF₃SO₃)₂] containing different concentrations of 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl) imide (EMIMTFSI) ionic liquid has been prepared by simple solution casting technique. The prepared films of gel polymer membranes have been characterized utilizing complex impedance spectroscopy, differential scanning calorimetry (DSC), thermogravimetric (TG), and cyclic voltammetry (CV) analyses. The dielectric constant and ionic conductivity pursue similar trend with increasing EMIMTFSI concentration. The addition of ionic liquid in varied amounts into the optimized polymer blend-salt system effectively reduces the glass transition temperature (T_g) of the film as revealed from differential scanning calorimetry results. The origin of an improved thermal stability and feasible cyclic performance in respect of the best conducting sample of the resultant gel polymer electrolytes was also examined by utilizing thermogravimetric and cyclic voltammetry measurements.     

Properties of gel polymer electrolytes based on poly(butyl acrylate) semi-interpenetrating polymeric networks toward Li-ion batteries

A new type of gel polymer electrolyte (GPE) based on poly(butyl acrylate) (PBA) semi-interpenetrating polymer networks (IPNs) and polyvinylidene fluoride (PVDF) was prepared in different molar ratios ranging from 1:0.5 to 1:1. A series of structure characterizations of PBA/PVDF had been measured using FTIR, XRD, and SEM. The electrolyte uptake test revealed that when the semi-IPNs were swollen with the commercial liquid electrolyte solutions, they showed an outstanding electrolyte uptake of 120% with a chemically cross-linked structure. All results indicated that the GPE exhibited the best performance when the molar ratio of BA and PVDF was 1:0.5. The prototype cell assembled with LiFePO₄ as cathode, lithium metal as anode, and GPE as the electrolyte as well as separator retained 94% of its initial specific capacity after 100 charge-discharge cycles, showing an excellent cycling stability and a high electrochemical window (up to 4.5 V against Li⁺/Li) at room temperature. Compared with the liquid electrolyte, the GPE exhibited a similar stable cycling performance and was suitable for practical application in Li-ion batteries.     

Unique dielectric properties in polyaniline/poly(vinylidene fluoride) composites induced by temperature variation

To explore an effect of temperature on the dielectric properties in polyaniline/poly(vinylidene fluoride) (PANI/PVDF) composites, the dielectric properties of these composites with different volumetric fractions of PANI (?_PANI) were studied in a wide temperature range. An increase in the effective conductivity (σ_eff) and dielectric permittivity (?_eff) was observed with increasing temperature in all PANI/PVDF composites. Particularly, for the composite with ?_PANI = 0.01, less than the percolation threshold (?_C = 0.045), the increase in σ_eff and ?_eff was most significant. A tunneling effect could be responsible for the unique dielectric properties. The results provided us useful information related to the microstructure of composites, which was not reported previously. (© 2008 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)