Pt-Ru supported on double-walled carbon nanotubes as high-performance anode catalysts for direct methanol fuel cells

Pt-Ru supported on carbon nanotubes (CNTs) (single-walled nanotubes, double-walled nanotubes (DWNTs), and multi-walled nanotubes) catalysts are prepared by an ethylene glycol reduction method. Pt-Ru nanoparticles with a diameter of 2-3 nm and narrow particle size distributions are uniformly deposited onto the CNTs. A simple and fast filtration method followed by a hot-press film transfer is employed to prepare the anode catalyst layer on a Nafion membrane. The Pt-Ru/DWNTs catalyst shows the highest specific activity for methanol oxidation reaction in rotating disk electrode experiments and the highest performance as an anode catalyst in direct methanol fuel cell (DMFC) single cell tests. The DMFC single cell with Pt-Ru/DWNTs (50 wt %, 0.34 mg Pt-Ru/cm(2)) produces a 68% enhancement of power density, and at the same time, an 83% reduction of Pt-Ru electrode loading when compared to Pt-Ru/C (40 wt %, 2.0 mg Pt-Ru/cm(2)).     

PtRu nanoparticles supported on 1-aminopyrene-functionalized multiwalled carbon nanotubes and their electrocatalytic activity for methanol oxidation

A new synthesis method for the preparation of high-performance PtRu electrocatalysts on multiwalled carbon nanotubes (MWCNTs) is reported. In this method, bimetallic PtRu electrocatalysts are deposited onto 1-aminopyrene (1-AP)-functionalized MWCNTs by a microwave-assisted polyol process. The noncovalent functionalization of MWCNTs by 1-AP is simple and can be carried out at room temperature without the use of expensive chemicals or corrosive acids, thus preserving the integrity and the electronic structure of MWCNTs. PtRu electrocatalysts on 1-AP-functionalized MWCNTs show much better distribution with no formation of aggregates, higher electrochemically active surface area, and higher electrocatalytic activity for the electrooxidation of methanol in direct methanol fuel cells as compared to that on conventional acid-treated MWCNTs and carbon black supported PtRu electrocatalysts. PtRu electrocatalysts on 1-AP-functionalized MWCNTs also show significantly enhanced stability.     

Multiwalled carbon nanotube supported PtRu for the anode of direct methanol fuel cells

The activity of the methanol oxidation reaction of a multiwalled carbon nanotube (MWCNT)-supported PtRu catalyst was investigated and compared with the Vulcan XC-72 carbon-supported catalyst. The PtRu nanoparticles with 1:1 and 7:3 atomic ratios (with similar PtRu loadings and morphological structures) were deposited both on the MWCNTs and on the carbon. Cyclicvoltammetry results demonstrated that the MWCNT-supported PtRu catalyst exhibited a higher mass activity (mA mg(-1) of PtRu) for the methanol oxidation reaction than the carbon-supported PtRu under the condition that both catalysts possess more or less the same PtRu loadings, particle sizes, dispersions, and electrochemical surface area. The direct methanol fuel cell performance test data showed that MWCNT-supported PtRu catalysts yielded about 35-39% higher power densities than the carbon-supported PtRu.     

High performance PtRuIr catalysts supported on carbon nanotubes for the anodic oxidation of methanol

We report the formation of a new PtRuIr catalyst using an organic colloid synthesis method, involving acetone as the solvent, ethylene glycol as the reducing agent, citrate as a complexing agent and stabilizer, and multiwall carbon nanotubes (CNT, diameter 8-10 nm) as the support. This catalyst has a very high real surface area and is highly active toward the oxidation of methanol, relevant to fuel cell applications. The Ir component appears to act as a promoter, and the splitting of the Pt(111) XRD feature into four peaks and the shift to larger d spacing reflect the high dispersion of the metallic components.     

甲醇常压气相羰基化碳纳米管负载金属镍催化剂

碳纳注管作为一类纳米级新型碳素材料,具有对反应物质和反应产物的特殊吸咐性能、特殊的孔腔空间立体选择性、碳与金属催化剂的金属-载体强相互作用（SMSI）以及管壁的可改性官能团等优点,近年来,已引起国内外学者的广泛关注。……     

Platinum catalysts supported on Nafion functionalized carbon black for fuel cell application

We report a high performance supported Pt catalyst, in which a perfluorosulfonic acid (Nafion) functionalized carbon black is used as support. The catalyst is characterized by infrared spectroscopy (IR), transmission electron microscopy (TEM) and X-ray diffraction (XRD). The TEM image shows that the active Pt component is in nanoparticles and highly dispersed on the carbon black with an average particle size of 1.9 nm. The catalyst shows improved activity towards the methanol anodic oxidation and oxygen reduction reaction (ORR), resulting from the high dispersion of active Pt component. It leads to increases in electrochemically accessible surface areas and ion channels, as well as easier chargetransfer at polymer/electrolyte interfaces. The high platinum utilization and high performance of Pt/Nafion-C catalyst make it a promising electrocatalyst for fuel cell application.     

Cu-Co-Fe oxide catalysts supported on carbon nanotubes for the oxidation of CO

The catalytic activity and adsorption characteristics of the surface of catalysts in the form of carbon nanotubes produced on nickel and cobalt oxides with the Cu-Co-Fe oxide system as supported active phase were studied. At carbon nanotubes produced on nickel oxide with (10 + 10) wt.% of the catalytically active phase total conversion of CO to CO₂ is realized at 47 °C. This sample has high specific surface area and a large volume of mesopores. It was shown that the increase in catalytic activity correlates with the increase in the amount of the α₂ form of CO₂. __________ Translated from Teoreticheskaya i éksperimental’naya Khimiya, Vol. 42, No. 4, pp. 222–226, July–August, 2006.     

Anodic activation of PtRu/C catalysts for methanol oxidation

Anodic treatment of PtRu/C catalysts in 0.5 M sulfuric acid at 1.3 V (vs RHE) for 0.5 h was found able to promote the activity for methanol oxidation by a few tenths to 5 times. This anodic activation effect was valid for samples domestically prepared under different conditions and that produced by Johnson-Matthey. On the basis of the changes of cyclic voltammetry during the anodic treatment, a model was proposed for the activation effect. According to the model, there are two categories of ruthenium oxides in the catalyst: one is electrochemically reversible and beneficial for catalytic activity, while the other is irreversible and harmful. During the anodic treatment, the harmful oxide is decreased, while the beneficial oxide either increased or changed only slightly, resulting in a beneficial net change.     

壳聚糖修饰炭黑负载Pt-Au催化剂对甲醇氧化的电催化性能

以炭黑及自制的壳聚糖-炭黑(CHI-C)复合材料为载体,采用溶胶负载法制备了Pt_m＾Au/C及Pt_m＾Au/CHI-C催化剂(＾ 代表Au、Pt为分步负载,m代表Pt/Au原子比),通过紫外-可见吸收光谱、X射线衍射、透射电镜及X射线光电子能谱对催化剂进行了表征。利用循环伏安法和计时电流法分别测定了Pt-Au催化剂对甲醇电催化氧化反应的活性和稳定性,考查了Pt/Au原子比及CHI改性对电催化活性和稳定性的影响。结果表明,Pt_1.0＾Au/C具有最高的催化活性,炭黑中加入少量CHI能提高Pt_1.0＾Au/C催化剂的稳定性。     

Fast preparation of PtRu catalysts supported on carbon nanofibers by the microwave-polyol method and their application to fuel cells

PtRu alloy nanoparticles (24 +/- 1 wt %, Ru/Pt atomic ratios = 0.91-0.97) supported on carbon nanofibers (CNFs) were prepared within a few minutes by using a microwave-polyol method. Three types of CNFs with very different surface structures, such as platelet, herringbone, and tubular ones, were used as new carbon supports. The dependence of particles sizes and electrochemical properties on the structures of CNFs was examined. It was found that the methanol fuel cell activities of PtRu/CNF catalysts were in the order of platelet > tubular > herringbone. The methanol fuel cell activities of PtRu/CNFs measured at 60 degrees C were 1.7-3.0 times higher than that of a standard PtRu (29 wt %, Ru/Pt atomic ratio = 0.92) catalyst loaded on carbon black (Vulcan XC72R) support. The best electrocatalytic activity was obtained for the platelet CNF, which is characterized by its edge surface and high graphitization degree.     

碳载Pt-Ni催化剂对直接甲醇燃料电池阴极氧电还原性能的影响

采用间歇式微波法制备了不同Pt、Ni原子比的碳载Pt-Ni催化剂。XRD结果表明,用这种方法制备的催化剂分散得比较好,具有较小的平均粒径,其中Pt-Ni/C(3∶1)催化剂的粒径最小。在旋转圆盘电极上进行氧的还原测试结果表明,当电解质溶液中没有甲醇和有甲醇存在时,Pt-Ni/C(3∶1)催化剂对氧的催化还原活性都很高,说明Pt-Ni/C(3∶1)催化剂对氧的催化还原受甲醇的影响较小。     

Nanoparticle size effects on methanol electrochemical oxidation on carbon supported platinum catalysts

The particle size effect observed on the performance of Pt/C electrocatalysts toward the methanol oxidation reaction (MOR) has been investigated with differential electrochemical mass spectrometry (DEMS). The investigation has been conducted under both potentiodynamic and potentiostatic conditions as research on methanol electrochemical oxidation is closely related to interest in direct methanol fuel cells. The particle size effect observed on the MOR is commonly regarded as a reflection of different Pt-CO and Pt-OH bond strengths for different particle sizes. This work focuses mainly on the mechanism of methanol dehydrogenation on platinum which is central to the problem of the optimization of the efficiency of methanol electro-oxidation by favoring the CO(2) formation pathway. It was found that the partitioning of the methanol precursor among the end products on supported platinum nanoparticles is strongly dependent on particle size distribution. Also, it is postulated that the coupling among particles of different sizes via soluble products must be considered in order to understand the particle size effects on the observed trends of product formation. An optimum particle size range for efficiently electro-oxidizing methanol to CO(2) was found between 3 and 10 nm, and loss in efficiency is mostly related to the partial oxidation of methanol to formaldehyde on either too small or too large particles. The possible reasons for these observations are also discussed.     

Poly(vinylpyrrolidone)-modified graphite carbon nanofibers as promising supports for PtRu catalysts in direct methanol fuel cells

Carbon nanomaterials, including herringbone graphite carbon nanofibers (GNFH), multiwalled carbon nanotubes (MWCNT), and carbon black, were surface-modified by a new poly(vinylpyrrolidone) (PVP) grafting process as well as by the conventional acid-oxidation (AO) process, and characterized by FTIR, TGA, Raman, HRTEM, XRD, and XPS measurements. Pt nanoparticles of 1.8 nm were evenly deposited on all PVP-grafted carbon nanomaterials. The effects of the two surface modification processes on the dispersion, average Pt nanoparticle sizes, the electrocatalytic performance, and electrical conductivities of Pt-carbon nanocomposites in direct methanol oxidation were systematically studied and compared. It was found that the PVP-grafted carbon nanomaterials have much less loss in the electric conductivity and thus better electrocatalytic performance, 17-463% higher, than their corresponding acid oxidation-treated nanocomposites. The electrocatalytic performance of the Pt-carbon nanocomposites decreases in the following order: Pt-PVP-GNFH > Pt-PVP-MWCNTarc > Pt-AO-MWCNTarc > Pt-PVP-MWCNTCVD > Pt-AO-MWCNTCVD > Pt-XC-72R > Pt-AO-GNFH, with the Pt-PVP-GNFH nanocomposite having approximately 270% higher performance than that of the Pt-Vulcan XC-72R nanocomposite. In addition, PtRu-PVP-GNFH shows even better (50% higher) electrocatalytic activity than the Pt-PVP-GNFH nanocomposite at a 0.6 V applied voltage.     

Titanium vanadium nitride supported Pt nanoparticles as high-performance catalysts for methanol oxidation reaction

Journal of Solid State Electrochemistry - In the present study, Pt nanoparticles (20 wt%) were successfully anchored on vanadium (V)-doped titanium nitride hybrid support, which...     

A strategy for the high dispersion of PtRu nanoparticles onto carbon nanotubes and their electrocatalytic oxidation of methanol

Carbon nanotubes (CNTs) were non-covalently functionalized by 1-pyrenecarboxaldehyde (PCA) via π-π stacking interactions. PCA not only acts as the reductant for the deposition of PtRu nanoparticles, but the oxidation product of PCA can also effectively anchor and stabilize the in-situ-produced PtRu?NPs on the surface of CNTs. Transmission electron microscopy demonstrates that PtRu?NPs are uniformly dispersed on the surface of CNTs with small particles sizes of about 1.7 nm. The obtained PtRu-NP/CNT composites have higher electrochemical surface areas, electrocatalytic activities, and better stability towards methanol oxidation compared to PtRu?NPs supported on pristine CNTs.     

PtFe catalysts supported on hierarchical porous carbon toward oxygen reduction reaction in microbial fuel cells

Journal of Solid State Electrochemistry - A new family of PtFe catalysts supported on hierarchical porous carbon (HPC), with different porous sizes, was developed and tested as cathodes in oxygen...     

Highly dispersed Pt catalysts on single-walled carbon nanotubes and their role in methanol oxidation

Well-dispersed Pt catalysts with very high utilization efficiencies for fuel cell reactions have been prepared by ethylene glycol reduction on polymer-wrapped single-walled carbon nanotubes (SWCNTs). By wrapping the SWCNTs in a polymer such as polystyrene sulfonate, we are able to break up the nanotube bundles to achieve better dispersion. These polymer-wrapped SWCNTs with platinum nanoparticles deposited on them show very high electrochemically active surface areas. The increase in utilization efficiencies for platinum catalysts on these SWCNT supports can be attributed to the increased surface areas and the well-dispersed nature of the carbon support and catalyst. The catalyst dispersion facilitates diffusion of reactant species which in turn results in higher methanol oxidation currents and more positive potentials for oxygen reduction.     

Synthesis and characterization of Pt-WO3 as methanol oxidation catalysts for fuel cells

Several compositions of Pt-WO3 catalysts were synthesized and characterized for the electro-oxidation of methanol and CO. The surface morphologies of the catalysts were found to be dependent on the composition. X-ray energy dispersive spectroscopy and X-ray photoelectron spectroscopy results suggest a surface enrichment of WO3 in the codeposited Pt-WO3 catalysts. Cyclic voltammetry and chronoamperometry in methanol show an improvement in catalytic activity for the Pt-WO3 catalysts. A significant improvement in the poison tolerance toward CO and other organic intermediates was observed in the mixed metal-metal oxide catalyst. The catalytic performance of the different compositions was directly compared by normalization of the current to active sites. CO-stripping voltammetry suggests the involvement of WO3 in the catalytic process as opposed to a mere physical effect as suggested by previous work. A possible mechanism for this improvement is proposed based on the electrochemical data.     

Pt and Ru X-ray absorption spectroscopy of PtRu anode catalysts in operating direct methanol fuel cells

In situ X-ray absorption spectroscopy, ex situ X-ray fluorescence, and X-ray powder diffraction enabled detailed core analysis of phase segregated nanostructured PtRu anode catalysts in an operating direct methanol fuel cell (DMFC). No change in the core structures of the phase segregated catalyst was observed as the potential traversed the current onset potential of the DMFC. The methodology was exemplified using a Johnson Matthey unsupported PtRu (1:1) anode catalyst incorporated into a DMFC membrane electrode assembly. During DMFC operation the catalyst is essentially metallic with half of the Ru incorporated into a face-centered cubic (FCC) Pt alloy lattice and the remaining half in an amorphous phase. The extended X-ray absorption fine structure (EXAFS) analysis suggests that the FCC lattice is not fully disordered. The EXAFS indicates that the Ru-O bond lengths were significantly shorter than those reported for Ru-O of ruthenium oxides, suggesting that the phases in which the Ru resides in the catalysts are not similar to oxides.     

铂、钌共修饰碳纳米管电极的制备及对甲醇的电催化氧化

碳纳米管以其独特的结构,良好的电性能和机械性能吸引了众多的关注~([1]),被认为是潜在的异相催化剂载体 ~([2]).近来关于碳纳米管负载催化剂的合成及其在异相催化中应用的研究已见报道~([3]).