Up-conversion emissions of Er<Superscript>3+</Superscript>-Yb<Superscript>3+</Superscript> codoped Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanoparticles by the arc discharge synthesis method

The Er³⁺-Yb³⁺ codoped Al₂O₃ nanoparticles with an average particle size of about 50 nm have been synthesized by an arc discharge synthesis method. The green and red up-conversion emissions centered at about 526, 547 and 677 nm, corresponding respectively to the ²H_11/2→⁴I_15/2, ⁴S_3/2→⁴I_15/2 and ⁴F_9/2→⁴I_15/2 transitions of Er³⁺, were detected by a 978-nm semiconductor laser diode excitation. The Annealing has evident effect on the up-conversion emissions of the samples: The red up-conversion emission is noticeable before annealing; however, the green up-conversion emission becomes predominant after annealing. The mixture of (Er,Yb)₃Al₅O₁₂ and α-(Al,Er,Yb)₂O₃ phases is more favorable for green up-conversion emissions due to an enhancement of the ESA (I) of ⁴I_11/2+a photon→⁴F_7/2 and ET (III) of ²F_5/2(Yb³⁺)+⁴I_11/2(Er³⁺)→²F_7/2(Yb³⁺)+⁴F_7/2(Er³⁺) processes. The two-photon absorption up-conversion process is involved in the green and red up-conversion emissions. The results have proved that arc discharge synthesis is a new promising preparation technology for optical materials. Supported by National Natural Science Foundation of China (Grant No. 10804015), the Scientific Research Foundation for Doctor of Liaoning Province (Grant No. 20071095), and the Educational Committee Foundation of Liaoning Province (Grant No. 2008123)     

VUV luminescence of Er<Superscript>3+</Superscript> ions in LiYF<Subscript>4</Subscript> and BaY<Subscript>2</Subscript>F<Subscript>8</Subscript> crystals

Vacuum ultraviolet luminescence of Er³⁺ ions in LiYF4 and BaY₂F₈ crystals has been investigated. It is revealed that under excitation by 193 nm radiation from an ArF excimer laser the interconfigurational 5d–4f radiative transitions in Er³⁺ ions are observed. It is shown that from the LiYF₄:Er crystal only the spin-forbidden luminescence (λ = 165 nm) is detected, whereas both the spin-forbidden (λ = 169 nm) and spin-allowed (λ = 160.5 nm) components are observed from the BaY₂F₈:Er crystal.     

Lasing Yb<Superscript>3+</Superscript> in crystals with a wavelength dependence anisotropy displayed from La<Subscript>2</Subscript>CaB<Subscript>10</Subscript>O<Subscript>19</Subscript>

We report spectroscopic and laser properties for propagation directions outside the principal axes of Yb³⁺-doped low symmetry laser crystals with a special devotion to the wavelength dependence anisotropy. We illustrate our report with experimental data in the 900–1075 nm range of wavelengths from the Yb³⁺:La₂CaB₁₀O₁₉ monoclinic crystal excited under laser diode pumping at 975 nm. This study, which makes easier the realization of Yb³⁺ lasers with an efficient free-running operation at the wavelength having the highest emission intensity or at a specified wavelength, or emitting two frequencies with a specified frequency difference, is of promising interest for applications.     

Quantum cutting in Gd<Subscript>2</Subscript>SiO<Subscript>5</Subscript>: Eu<Superscript>3+</Superscript> by VUV excitation

The emission and excitation spectra of Gd₂SiO₅∶Eu³⁺ were investigated using the VUV beam line of the Beijing Synchrotron Radiation Facility (BSRF). The experimental results were discussed in the frame of visible quantum cutting process involved in Gd³⁺−Eu³⁺ system. Upon direct excitation into the⁶G _J states of Gd³⁺, two visible photon emissions from Eu³⁺ were observed. Cursory evaluation proved that Gd₂SiO₅∶Eu³⁺ is an efficient visible quantum cutter.     

Synthesis and characterization of mono-dispersed Y<Subscript>3</Subscript>Al<Subscript>5</Subscript>O<Subscript>12</Subscript>:Er<Superscript>3+</Superscript>-coated SiO<Subscript>2</Subscript> nanoparticles by co-precipitation process

In this paper, a facile co-precipitation process for preparing mono-dispersed core–shell structure nanoparticles is reported. The 110 nm SiO₂ cores coated with an yttrium aluminum garnet (Y₃Al₅O₁₂) layer doped with Er³⁺ were synthesized and the influence of the concentration ratio of [urea]/[metal ions] on the final product was investigated. The structure and morphology of samples were characterized by the X-ray powder diffraction, Fourier transform IR spectroscopy and transmission electron microscopy, respectively. The results indicate that a layer of well-crystallized garnet Y₃Al₅O₁₂:Er³⁺ were successfully coated on the silica particles with the thickness of 20 nm. The near infrared and upconversion luminescent spectra of the SiO₂@Y₃Al₅O₁₂:Er³⁺ powders further confirm that a Y₃Al₅O₁₂:Er³⁺ coating layer has formed on the surface of silica spherical particles.     

Spectroscopic Properties and Energy Transfer Analysis of Tm<Superscript>3+</Superscript>-Doped BaF<Subscript>2</Subscript>-Ga<Subscript>2</Subscript>O<Subscript>3</Subscript>-GeO<Subscript>2</Subscript>-La<Subscript>2</Subscript>O<Subscript>3</Subscript> Glass

This paper reports on the spectroscopic properties and energy transfer analysis of Tm³⁺-doped BaF₂-Ga₂O₃-GeO₂-La₂O₃ glasses with different Tm₂O₃ doping concentrations (0.2, 0.5, 2.0, 2.5, 3.0, 3.5, 3.5, 4.0 wt%). Mid-IR fluorescence intensities in the range of 1,300 nm−2,200 nm have been measured when excited under an 808 nm LD for all the samples with the same pump power. Energy level structure and Judd-Ofelt parameters have been calculated based on the absorption spectra of Tm³⁺, cross-relaxation rates and multi-phonon relaxation rates have been estimated with different Tm₂O₃ doping concentrations. The maximum fluorescence intensity at around 1.8 μm has been obtained in Tm₂O₃-3 wt% sample and the maximum value of calculated stimulated emission cross-section of Tm³⁺ in this sample is about 0.48 × 10⁻²⁰ cm² at 1,793 nm, and there is not any crystallization peak in the DSC curve of this sample, which indicate the potential utility of Tm³⁺-doped BaF₂-Ga₂O₃-GeO₂- La₂O₃ glass for 2.0-μm optical fiber laser.     

Investigation on structural characteristics of PVDF–AgCF<Subscript>3</Subscript>SO<Subscript>3</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanocomposite solid polymer electrolyte system

There has been an increasing interest towards the incorporation of nanosize ceramic fillers in polymer electrolytes. Solid polymer electrolytes based on polyvinylidene fluoride (PVDF), silver triflate (AgCF₃SO₃), and x wt% of aluminum oxide (Al₂O₃) nanopowders (where x = 1, 3, 5, and 10, respectively) have been prepared using solution casting technique. The structural characteristics of these thin film specimens were studied using Fourier transform infrared (FTIR) and X-ray diffraction (XRD) patterns at room temperature. The appearance of new absorption bands and gradual shifts observed in some characteristic peaks confirmed the complex formation between polyvinylidene fluoride and silver triflate. Furthermore, the addition of nanosized filler Al₂O₃ has also indicated the interaction of the filler with the polymer salt complex. The XRD patterns obtained for all these samples in the 2θ range 10° to 70° showed the amorphous nature of these samples. Paper presented at the Third International Conference on Ionic Devices (ICID 2006), Chennai, Tamilnadu, India, December 7–9, 2006.     

Luminescence in Dy<Superscript>3+</Superscript> and Eu<Superscript>3+</Superscript> Activated K<Subscript>3</Subscript>Al<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>

The Dy³⁺ and Eu³⁺ activated K₃Al₂ (PO₄)₃ phosphors were prepared by a combustion synthesis. From a powder X-ray diffraction (XRD) analysis the formation of K₃Al₂ (PO₄)₃ was confirmed. In the photoluminescence emission spectra, the K₃Al₂(PO₄)₃:Dy³⁺ phosphor emits two distinctive colors: blue and yellow whereas K₃Al₂(PO₄)₃:Eu³⁺ emits red color. Thus the combination of colors gives BYR (blue–yellow–red) emissions can produce white light. These phosphors exhibit a strong absorption between 340 and 400 nm which suggest that present phosphor is a promising candidate for producing white light-emitting diodes (LED).     

Spectral and kinetic characteristics of CdI<Subscript>2</Subscript> and CdI<Subscript>2</Subscript>:Pb scintillators

We have studied the effect of lead dopant on the optical absorption, photoluminescence, and x-ray luminescence spectra, and the scintillation characteristics of CdI₂ at room temperature. The crystals for the study were grown by the Stockbarger-Bridgman method. Activation of CdI₂ from the melt by the compound PbI₂ leads to the appearance in the absorption spectra in the near-edge region of an activator band at 395–405 nm, which is interpreted as an A band connected with electronic transitions from the ¹S₀ state to the ³P₁ levels in the Pb²⁺ ion. For x-ray excitation, CdI₂:Pb²⁺ crystals with optimal dopant concentration (∼1.0 mol%) are characterized by a light yield with maximum in the 570–580 nm region that is an order of magnitude higher than for CdI₂ crystals in the 490–500 nm band. For α excitation, the radioluminescence kinetics for cadmium iodide is characterized by a very short (∼0.3 nsec) rise time and fast decay of luminescence, with τ₁ ≈ 4 nsec and τ₂ = 10–76 nsec. Depending on the conditions under which the crystals were obtained, the fast component fraction is 95%–99%. The crystal is characterized by a similar scintillation pulse in the case of excitation by x-ray pulses. The radioluminescence pulse shape for CdI₂:Pb in the decay stage is predominantly exponential, with luminescence decay time constants τ₁ ≈ 10 nsec and τ₂ = 200–250 nsec. This system is characterized by low afterglow, at the level for the Bi₄G₃O₁₂ scintillator. We have demonstrated the feasibility of using CdI₂:Pb as a scintillator for detecting α particles. Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 75, No. 6, pp. 825–830, November–December, 2008.     

Wavelength tunable linear cavity cladding pump Er<Superscript>3+</Superscript>/Yb<Superscript>3+</Superscript>co-doped fiber laser operating in L-band

We have demonstrated a novel tunable linear cavity Er³⁺/Yb³⁺ co-doped fiber laser, which utilizes amplified spontaneous emission as a secondary pump source so that it can operate in L-band. The tuning wavelength range can be up to 34 nm, from 1588.6 to 1622.6 nm, and the output power excursion of the laser at different wavelengths can be less than 0.4 dB by using a two sections of high-birefringence fiber loop mirror as the wavelength filter. The high output power of 200 mW is realized by using the cladding-pump.     

Continuous wave laser operation of Yb<Superscript>3+</Superscript>:YVO<Subscript>4</Subscript>

We have demonstrated the continuous wave laser operation of Yb³⁺:YVO₄. For Ti:Al₂O₃ laser pumping at 985 nm, a maximum slope efficiency of 41.1% and a threshold pump power of 76 mW were obtained. The maximum output power was 433 mW at a laser wavelength of 1037 nm.Using a cw diode laser around 974 nm as a pump source, a slope efficiency of 10.9% and a maximum output power of 152 mW were achieved at a laser wavelength of 1039 nm. The laser threshold pump power was 608 mW with respect to the absorbed pump power. The effective emission cross-sections for the ²F_5/2²F_7/2 transition were determined using the Füchtbauer–Ladenburg equation. The maxima of the effective absorption and emission cross-sections were found at 984.5 nm (6.74×10^-20 cm²) in -po larization and 985.5 nm (4.28×10^-20 cm²) also in -p olarization. The upper laser level lifetime was measured with suppression of radiation trapping and is around 318 s. PACS 42.55.Rz; 42.55.Xi; 42.70.Hj     

Synthesis and luminescent properties of Eu<Superscript>3+</Superscript>- and Eu<Superscript>2+</Superscript>-activated sodium pyrophosphate Na<Subscript>4</Subscript>P<Subscript>2</Subscript>O<Subscript>7</Subscript>

The luminescent properties of Eu³⁺ and Eu²⁺ ions in sodium pyrophosphate, Na₄P₂O₇, have been studied. The excitation spectrum of the Eu³⁺ emission in Na₄P₂O₇ consists of several sets of bands in the range 280–535 nm due to 4f–4f transitions of Eu³⁺ ions and a broad band with a maximum at about 240 nm interpreted to be due to a charge transfer (CT) transition from oxygen 2p states to empty states of the Eu³⁺ 4f⁶-configuration. Although the CT band energy is large enough, the quantum efficiency (η) of the Eu³⁺ emission in Na₄P₂O₇ under CT excitation was estimated to be very low (η ≤ 0.01). In terms of a configurational coordinate model, this fact is interpreted as a result of the high efficiency of a radiationless relaxation from the CT state to the ⁷F₀ ground state of Eu³⁺ ions occupying sodium sites in Na₄P₂O₇. A strong reducing agent is required in order to stabilize Eu²⁺ ions in Na₄P₂O₇ during the synthesis. Several nonequivalent Eu²⁺ luminescence centers in Na₄P₂O₇ were found.     

Electrical properties of Na<Subscript>2</Subscript>SO<Subscript>4</Subscript>-based composite systems

Composite electrolytes are well-known multiphase systems and exhibit maxima in the conductivity at certain second-phase concentration. An attempt has been made to investigate a number of sodium sulfate (Na₂SO₄)-based composite systems. The dispersoids that have been used are MgO, Al₂O₃, and SiO₂. The samples have been characterized using impedance spectroscopy, X-ray diffraction, and differential scanning calorimetry. The maximum conductivity has been observed for MgO dispersed system, and the percolation threshold has been observed at 30-mol% dispersoid, MgO concentration. Interestingly, two maxima have been observed in case of the Na₂SO₄–SiO₂ and Na₂SO₄–Al₂O₃ composite systems. In the Na₂SO₄–SiO₂ system, the first maximum occurs at lower concentration, i.e., in the range between 10 and 20 mol%, whereas the second occurs at the 40-mol% dispersoid concentration. For the Na₂SO₄–Al₂O₃ system, although slightly indistinguishable, two peaks in the conductivity vs composition plot have been observed around 12- and 30-mol% Al₂O₃ concentrations.     

Magnetic ground state and the spin-state transitions in YBaCo<Subscript>2</Subscript>O<Subscript>5.5</Subscript>

The crystal and magnetic structure of the perovskite-like, oxygen deficient cobalt oxide YBaCo₂O_5.5 has been studied by means of neutron and X-ray diffraction in the 10–300 K temperature range. The magnetic ground state is characterized by a coexistence of two distinct antiferromagnetic phases. In the first one, the ionic moments of high-spin Co³⁺ ions in the pyramidal sites are ordered in a spiral arrangement, while octahedral sites are non-magnetic due to presence of low-spin Co³⁺ ions. The arrangement in the second phase is collinear of the G-type, with non-zero moments both in pyramidal (high-spin Co³⁺ ions) and octahedral sites (presumably a mixture of the low- and high-spin states). With increasing temperature, at 260–300 K, the system develops a gradual structural transformation, which is associated with appearance of spontaneous magnetic moment. This process is related to a thermally induced reversion of low- and high-spin states at the octahedral sites to the intermediate-spin Co³⁺ states, resulting in an insulator-metal transition at T_C ≈ T_IM ≈ 295 K.     

Preparation of TiO<Subscript>2</Subscript>-coated LiCo<Subscript>1/3</Subscript>Ni<Subscript>1/3</Subscript>Mn<Subscript>1/3</Subscript>O<Subscript>2</Subscript> by electrostatic self-assembly method and its properties

A precursor of TiO₂–LiCo_1/3Ni_1/3Mn_1/3O₂ was prepared by electrostatic self-assembly method. The final product was obtained by heating the precursor at 400–450 °C for 4–6 h in air. X-ray diffraction (XRD), scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS), and electrochemical tests were used to examine the structural, morphology, elementary valence, and electrochemical characteristics. XRD indicated that the TiO₂-coated material can be indexed by α-NaFeO₂ layered structure, which belongs to hexagonal-type space group R3m. XPS results confirmed the existence of TiO₂ compound on the surface of the coated sample. The SEM image showed that the material had spherically porous morphology with the uniform size about 6 μm. The initial charge–discharge capacity of the TiO₂-coated LiCo_1/3Ni_1/3Mn_1/3O₂ material was 168.8/160.0 mAh/g. After 60 cycles, the discharge capacity of the TiO₂-coated LiCo_1/3Ni_1/3Mn_1/3O₂ sample was 147.0 mAh/g, and the coulombic efficiency was 94.0%. Compared with the uncoated sample, the electrochemical performance of TiO₂-coated LiCo_1/3Ni_1/3Mn_1/3O₂ was improved.     

Optical transmission of ceramic shielding blocks made from Al<Subscript>2</Subscript>O<Subscript>3</Subscript>

We have studied the transmission of bulk Al₂O₃ ceramic used as heat shields for the working chamber of a turbine. We have established that radiation scattered from such an object has a pronounced speckle structure, while the scattering indicatrix is the same as the indicatrix for an ideal scatterer. We show that existing highpower semiconductor laser sources make it possible to penetrate sufficiently deeply into such materials, and the small transmission coefficient is not the limiting factor for development of optical methods for inspecting the quality of ceramic shielding blocks. __________ Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 74, No. 2, pp. 237–240, March–April, 2007.     

Nanosecond photoelectric effects in all-oxide p-n junction of La<Subscript>0.9</Subscript>Sr<Subscript>0.1</Subscript>MnO<Subscript>3</Subscript>/SrNb<Subscript>0.01</Subscript>Ti<Subscript>0.99</Subscript>O<Subscript>3</Subscript>

Nanosecond (ns) photoelectric effects have been observed in all-oxide p-n junctions of La_0.9Sr_0.1MnO₃/SrNb_0.01Ti_0.99O₃ for the first time. The rise time was about 23 ns and the full width at half maximum was about 125 ns for the open-circuit photovoltaic pulse when the La_0.9Sr_0.1MnO₃ thin film in the p-n junction was irradiated by a laser of ≈20 ns pulse duration and 308 nm wavelength. The photovoltaic sensitivity was 80 mV/MJ for a 308 nm laser pulse.     

Theoretical study of ZnO adsorption and bonding on Al<Subscript>2</Subscript>O<Subscript>3</Subscript> (0001) surface

ZnO adsorption on sapphire (0001) surface is theoretically calculated by using a plane wave ultrasoft pseudo-potential method based onab initio molecular dynamics. The results reveal that the surface relaxation in the first layer Al-O is reduced, even eliminated after the surface adsorption of ZnO, and the chemical bonding energy is 434.3(±38.6) kJ · mol⁻¹. The chemical bond of ZnO (0.185 ± 0.01 nm) has a 30° angle away from the adjacent, Al-O bond, and the stable chemical adsorption position of the Zn is deflected from the surface O-hexagonal symmetry with an angle of about 30°. The analysis of the atomic populations, density of state and bonding electronic density before and after the adsorption indicates that the chemical bond formed by the O²⁻ of the ZnO and the surface Al³⁺ has a strong ionic bonding characteristic, while the chemical bond formed by the Zn²⁺ and the surface O²⁻ has an obvious covalent characteristic, which comes mainly from the hybridization of the Zn 4s and the O 2p and partially from that of the Zn 3d and the O 2p.     

Luminescence of CaGa<Subscript>2</Subscript>Se<Subscript>4</Subscript>:Eu crystals

We have studied photoluminescence and thermoluminescence (PL and TL) in CaGa₂Se₄:Eu crystals in the temperature range 77–400 K. We have established that broadband photoluminescence with maximum at 571 nm is due to intracenter transitions 4f⁶ 5d–4f⁷ (⁸S_7/2) of the Eu²⁺ ions. From the temperature dependence of the intensity (log I–10³/T), we determined the activation energy (E _a = 0.04 eV) for thermal quenching of photoluminescence. From the thermoluminescence spectra, we determined the trap depths: 0.31, 0.44, 0.53, 0.59 eV. The lifetime of the excited state 4f6 5d of the Eu²⁺ ions in the CaGa₂Se₄ crystal found from the luminescence decay kinetics is 3.8 μsec. Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 76, No. 1, pp. 112–116, January–February, 2009.     

Diode pumped Pr<Superscript>3+</Superscript>:LiYF<Subscript>4</Subscript>-BBO ultraviolet laser at 320 nm

A diode pumped Pr³⁺:LiYF₄ laser at 639.5 nm has been demonstrated. With an incident pump power of 920 mW, the maximum red output power was 272 mW. Moreover, intracavity second-harmonic generation (SHG) has also been achieved with a maximum ultraviolet power of 23 mW by using a β-BaB₂O₄ (BBO) nonlinear crystal. To the best of our knowledge, this is the first report on continuous-wave ultraviolet generation by intracavity frequency doubling Pr³⁺:LiYF₄ laser.