首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 15 毫秒
1.
In this work the intrinsic viscosity of poly(ethylene glycol)/poly(vinyl pyrrolidone) blends in aqueous solutions were measured at 283.1–313.1 K. The expansion factor of polymer chain was calculated by use of the intrinsic viscosities data. The thermodynamic parameters of polymer solution (the entropy of dilution parameter, the heat of dilution parameter, theta temperature, polymer–solvent interaction parameter and second osmotic virial coefficient) were evaluated by temperature dependence of polymer chain expansion factor. The obtained thermodynamic parameters indicate that quality of water was decreased for solutions of poly(ethylene oxide), poly(vinyl pyrrolidone) and poly(ethylene oxide)/poly(vinyl pyrrolidone) blends by increasing temperature. Compatibility of poly(ethylene oxide)/poly(vinyl pyrrolidone) blends were explained in terms of difference between experimental and ideal intrinsic viscosity and solvent–polymer interaction parameter. The results indicate that the poly(ethylene glycol)/poly(vinyl pyrrolidone) blends were incompatible.  相似文献   

2.
In the present study the miscibility behaviour and the biodegradability of poly(ε-caprolactone)/poly(propylene succinate) (PCL/PPSu) blends were investigated. Both of these aliphatic polyesters were laboratory synthesized. For the polymer characterization DSC, 1H NMR, WAXD and molecular weight measurements were performed. Blends of the polymers with compositions 90/10, 80/20, 70/30 and 60/40 w/w were prepared by solution-casting. DSC analysis of the prepared blends indicated only a very limited miscibility in the melt phase since the polymer-polymer interaction parameter χ12 was −0.11. In the case of crystallized specimens two distinct phases existed in all studied compositions as it was found by SEM micrographs and the particle size distribution of PPSu dispersed phase increased with increasing PPSu content. Enzymatic hydrolysis for several days of the prepared blends was performed using Rhizopus delemar lipase at pH 7.2 and 30 °C. SEM micrographs of thin film surfaces revealed that hydrolysis affected mainly the PPSu polymer as well as the amorphous phase of PCL. For all polymer blends an increase of the melting temperatures and the heat of fusions was recorded after the hydrolysis. The biodegradation rates as expressed in terms of weight loss were faster for the blends with higher PPSu content. Finally, a simple theoretical kinetic model was developed to describe the enzymatic hydrolysis of the blends and the Michaelis-Menten parameters were estimated.  相似文献   

3.
The Flory-Huggins interaction parameter for a polymer solution can be represented as the product of two functions, which separately take into account the effects of the polymer volume fraction and temperature. The latter factor contains three constants, usually viewed as best-fit coefficients. They are expressed in terms of two thermodynamic quantities, namely, the excess partial molar heat capacity of the solution and a reference temperature, thus allowing to guess their physical meaning. The formulae so obtained were tested with satisfactory results for two solutions of polystyrene in acetone and for two polymer blends (PC/PMMA and PS/PVME.) Furthermore, an attempt was made to calculate the above-mentioned reference temperature from data referring to the phases in solution.  相似文献   

4.
The properties of multiphase polymer blends are determined in part by the nature of the polymer‐polymer interface. The interfacial tension, γ, influences morphology development during melt mixing while interfacial thickness, λ, is related to the adhesion between the phases in the solid blend. A quantitative relation between the thermodynamic interaction energy and these interfacial properties was first proposed in the theory of Helfand and Tagami and has since been correlated with experimental measurements with varying degrees of success. This paper demonstrates that the theory and experiment can be unified for polymer pairs of some technological importance: copolymers of styrene and acrylonitrile (SAN) with poly (2, 6‐dimethyl‐1, 4‐phenylene oxide) (PPO) and with bisphenol‐A polycarbonate (PC). For each pair, the overall interaction energy was calculated using a mean‐field binary interaction model expressed in terms of the interactions between repeat unit pairs extracted from blend phase behavior. Predictions of γ and λ as a function of copolymer composition made by combining the binary interaction model with the Helfand‐Tagami theory compare favorably with experimental measurements.  相似文献   

5.
剪切流动是高分子共混物流变学的重要内容之一。文章综述了不同高分子共混体系的理论和实验研究,主要包括剪切流动的因素和可能的方程,介绍了一些高分子共混物体系剪切流动的研究概况及热力学研究方法。  相似文献   

6.
A family of conformational rheological models for multi‐component miscible polymer blends is developed using a modified form of the Poisson bracket formulation. Two conformation tensors called c 1 and c 2 are introduced to show the orientation of the first and the second components of a blend, respectively. The mobility tensor and the energy function for each blend component are expressed in terms of these conformation tensors. The interaction effects are also included by energy expressions. The predictions of this family of “volume‐preserving” models are illustrated for a Hookean‐type energy function and several expressions of the modified mobility tensors. The results are illustrated for material functions in transient (start‐up and relaxation) and steady shear flows. The predictions are compared with experimental data taken from the literature for a miscible polymer blend. Study of the model sensitivity to its parameter shows that model predictions can cover a wide range of rheological behavior generally observed for multi‐component miscible polymer blends in steady and transient shear flows.

Experimental data and model predictions for steady shear viscosity for HDPE/LDPE blends.  相似文献   


7.
Patterned polymer structures with different functionalities have many potential applications. Directed assembly of polymer blends using chemically functionalized patterns during spin-coating has been used to fabricate the patterned polymer structures. For bridging the gap between laboratorial experiments and manufacturing of nanodevices, the polymer blends structures are required to be precisely patterned into nonuniform geometries in a high-rate process, which still is a challenge. In this Article, we demonstrated for the first time that by decreasing the interfacial tension between two polymers polystyrene and poly(acrylic acid) via adding a compatibilizer (polystyrene-b-poly(acrylic acid) ), a polystyrene/poly(acrylic acid) blend was precisely patterned into nonuniform geometries in a high-rate fashion. The patterned nonuniform geometries included angled lines with angles varied from 30° to 150°, T-junctions, square arrays, circle arrays, and arbitrary letter-shaped geometries. The reduction in the interfacial tension improved the line edge roughness and the patterning efficiency of the patterned polymer blends. In addition, the commensurability between characteristic length and pattern periodicity for well-ordered morphologies was also expanded with decreasing interfacial tension. This approach can be easily extended to other functional polymers in a blend and facilitate the applications of patterned polymer structures in biosensors, organic thin-film electronics, and polymer solar cells.  相似文献   

8.
Corona-electrets based on heterogeneous blends of high-density polyethylene and polystyrene were studied. The observed double-maximum composition dependence of the electret properties of polymer blends was explained in terms of the concept of their colloid structure and electrical conductivity.  相似文献   

9.
文章是《高分子共混物剪切流动的研究Ⅰ.研究概况及热力学方法》的续篇,介绍高分子共混物剪切流动的研究进展,涉及动力学、散射光和数值模拟等三种研究方法。  相似文献   

10.
从注射制品形态控制和结构表征的角度探讨高分子材料加工-形态-性能之间的关系.研究中采用动态保压成型方法来制备注射样品,在注射成型过程中引入剪切应力场的作用,制得的样品表现出明显的多层次结构,从外向里分别为皮层、剪切层、芯层,表现出不同的相形态、结晶形貌以及取向行为.研究发现,剪切应力对聚烯烃的形态发展和结构变化具有重要影响.在剪切应力的作用下,聚烯烃共混物中分散相会发生变形、取向,从而导致共混物的相转变点发生移动;结晶形态从球晶转变为shish-kebab结构;聚烯烃共混物在高剪切应力下相容,低剪切下发生相分离;HDPE/PP共混物的注射制品中出现附生结晶等现象.  相似文献   

11.
Polymer/polymer interaction parameters χ′23 have been measured at 120°C as a function of polymer concentration for six different poly(vinyl chloride)/linear aliphatic polyester blends. The technique used is inverse-phase gas chromatography with several molecular probes. The polymers investigated are poly(DL-lactide), poly(ethylene succinate), poly(ethylene adipate), poly(butylene adipate), poly(δ-valerolactone), poly(ε-caprolactone) and poly(hexamethylene sebacate). Probe/polymer interaction parameters χ12 and polymer/polymer interaction parameters χ′23 values are dependent upon the methylene to carbonyl ratio of the polyester, reaching a minimum for a value of 5, this ratio corresponding to poly(ε-caprolactone) blends. Results are interpreted in terms of pairwise interactions between carbonyl, methylene, and [CHCl] groups.  相似文献   

12.
Emulsion blends comprise an important commercial area of polymer blend utility. Surprisingly, the fundamental study of emulsion blends is rarely noted in the literature. This study investigates emulsion blends of poly(vinyl acetate) (PVAc) and vinyl acetate‐ethylene copolymers (VAE), where both components employ poly(vinyl alcohol) (PVOH) as the protective colloid. PVOH comprises the continuous phase in the emulsion cast films for both the individual components and the blends. This provides an example whereby excellent adhesion can be expected between the particles comprising the blend. The combination of low Tg/high Tg emulsion blends has been noted to be of interest, and the PVAc/VAE emulsion blends noted here offer an excellent model to study. The PVAc/VAE blends protected with PVOH exhibit poor mechanical compatibility even though there is good adhesion. Conventional theory based on polymer/filler combinations predicts a rapid loss in elongation as filler content increases if excellent adhesion is observed. The PVAc/VAE blends (where PVAc is the filler) also exhibit similar behavior. This result implies excellent adhesion may not be desired where a compliance mismatch occurs for emulsion blends. The polymer/filler theories do not properly predict PVAc/VAE blend tensile strength results. A newer approach termed the equivalent box model (EBM) employing percolation theory agrees well with experimental results. Melt mixing of the low/high compliance PVAc/VAE emulsion blends yields a significant improvement in mechanical compatibility. This indicates that a heterogeneous mixture of the same components yields better mechanical results than an array of particles with excellent adhesion between the particles.  相似文献   

13.
Polymer blends undergo external stresses such as pressure and shear in course of processing cycles. The knowledge of their phase behavior at each step of these cycles is crucial for understanding their physical properties and eventually improves their performance in practical applications. The effects of shear on the phase diagram of binary polymer blends are considered. A theoretical formulism is used upon which the free energy is the sum of two terms. The first term is modeled with the Flory–Huggins free energy of mixing and describes the thermodynamic behavior of the system in the quiescent state. The second term represents the excess free energy stored during flow. In the presence of shear flow, the excess free energy is expressed in terms of the viscosity and the shear modulus. Both quantities depend on composition and shear rate. The curvature of the variation of viscosity versus composition has a tremendous impact upon the nature of phase separation. Phase diagrams are described by the spinodal curves and show for the case considered here miscibility enhancement with increasing shear rate. A good correlation is found with experimental data of the literature on blends of polystyrene acrylonitril copolymer and polymethylmethacrylate. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011  相似文献   

14.
Successful blending of different polymers to make a structural or functional material requires overcoming limitations due to immiscibility and/or incompatibility that arise from large polymer-polymer interfacial tensions. In the case of latex blends, the combination of capillary adhesion during the blended dispersion drying stage with electrostatic adhesion in the final product is an effective strategy to avoid these limitations, which has been extended to a number of polymer blends and composites. This work shows that adhesion of polymer domains in blends made with natural rubber and synthetic latexes is enhanced by electrostatic adhesion that is in turn enhanced by ion migration, according to the results from scanning electric potential microscopy. The additional attractive force between domains improves blend stability and mechanical properties, broadening the possibilities and scope of latex blends, in consonance with the "green chemistry" paradigm. This novel approach based on electrostatic adhesion can be easily extended to multicomponent systems, including nonpolymers.  相似文献   

15.
16.
曾科  杨刚 《高分子科学》2017,35(12):1561-1571
A series of polymer blends were prepared from 1,3-bis(3,4-dicyanophenoxy)benzene (3BOCN) and epoxy resin with methyl tetrahydrophthalic anhydride as curing agent.The curing behavior and curing kinetics of the blends were studied by differential scanning calorimetry.The apparent activation energy of the blends with various contents of 3BOCN was higher than that of the blends without 3BOCN.A model experiment suggested that there is no obvious reaction between phthalonitrile and epoxy.The thermal and mechanical properties of the polymer blends were evaluated.The polymer blends exhibit high storage modulus and char yield compared with the neat epoxy.The polymer blends show ductile fracture morphology by scanning electron microscopy (SEM) images.  相似文献   

17.
This contribution embraces two topics related to phase behavior of polymer blends under equilibrium and nonequilibrium. 1. Polymer blends can undergo different phase changes as liquid-liquid phase transition and crystallization. Coupling of demixing and crystallization may occur at the kinetic stage. This is illustrated by blends of poly(ϵ-caprolactone)(PCL) and poly(styrene-co-acrylonitrile)(SAN). 2. Extension of studies to blend systems under flow is necessary for the better understanding of structure formation in polymer blends outside equilibrium. Polymer molecules will be oriented and stretched when subjected to flow. This may result in flow-induced phenomena. Effects of flow on the phase behavior have been studied only for a few blends, as yet. The primary observation was flow-induced miscibility. Apparent shifts of the phase transition temperatures will be discussed qualitatively in terms of a decoupled mode theory.  相似文献   

18.
The volume changes of rubber modified polymers under creep at room temperature were successfully used to characterize the toughening mechanisms of blends with brittle polymer matrices such as high impact polystyrene.This approach cannot be applied to pseudo-ductile polymers such as polypropylene and polyamide,because they are ductile when stretched at low speed at room temperature.Based on the time-temperature equivalence princi ple,the volume change at low temperature is proposed to characterize quantitatively the toughening mechanisms of polymer blends with ductile matrices,which is illustrated by applying this approach to rubber modified polypropylene  相似文献   

19.
The polystyrene-based polymer blends, partially miscible poly(bisphenol A carbonate)/polystyrene (PC/PS) and completely miscible poly(2,6-dimethylphenylene oxide)/polystyrene (PPO/PS), in nanorods with gradient composition distribution were discussed. The polymer blend nanorods were prepared by infiltrating the polymer blends into nanopores of anodic aluminum oxide (AAO) templates via capillary action. Their morphology was investigated by micro-Fourier transform infrared spectroscopy (micro-FTIR) and nano-thermal analysis (nano-TA) with spatial resolution. The composition gradient of polymer blends in the nanopores is governed by the difference of viscosity and miscibility between the two polymers in the blends and the pore diameter. The capillary wetting of porous AAO templates by polymer blends offers a unique method to fabricate functional nanostructured materials with gradient composition distribution for the potential application to nanodevices.  相似文献   

20.
The present report deals with some results on phase behavior, miscibility and phase separation for several polymer blends casting from solutions. These blends are grouped as the amorphous polymer blends, blends containing a crystalline polymer or two crystalline polymers. The blends of PMMA/PVAc were miscible and underwent phase separation at elevated temperature, exhibited LCST behavior. The benzoylated PPO has both UCST and LCST nature. For the systems composed of crystalline polymer poly(ethylene oxide) and amorphous polyurethane, of two crystalline polymers poly(-caprolactone) and poly[3,3,-bis-(chloromethyl) oxetane], appear a single Tg, indicating these blends are miscible. The interaction parameter B's were determined to be –14 J cm–3, –15 J cm–3 respectively. Phase separation of phenolphthalein poly(ether ether sulfone)/PEO blends were discussed in terms of thermal properties, such as their melting and crystallization behavior.This revised version was published online in November 2005 with corrections to the Cover Date.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号