Characterization of the oxidized beta-Si3N4 whisker surface layer using XPS and TOF-SIMS.

The change in composition of the surface layer of beta-Si3N4 whiskers was examined after heat treatment in atmosphere. At 873 K, the beta-Si3N4 whisker was barely oxidized. At 1273 K, the oxidation of the surface layers of the whisker occurred easily. With the beta-Si3N4 oxidation, the Si-N bond gradually changed into the Si-N-O bond, and finally became the oxidized layer (amorphous layer) of the whisker surface. It was assumed that the whisker surface has a gradient interface structure which gradually changes from the oxide layer of the whisker's outer surface to the nitride crystal of the inside layer. It was confirmed that impurity elements such as Y and Ca existed mainly in the amorphous region near the interface between the amorphous layer and the crystal layer.     

On the early stage of aluminum oxidation: An extraction mechanism via oxygen cooperation

We propose a barrierless mechanism for describing the oxidation of Al(111) in which oxygen atoms located on the outer surface extract aluminum atoms of the surface layers through local cooperation of other pre-adsorbed oxygen atoms. We show the details of this complex chemical process that kinetically competes with the non-destructive formation of an oxygen monolayer onto the Al surface, thus elucidating the initial aluminum oxidation regime. We demonstrate that further stripping of the complete surface Al layer is consistent with both (i) the formation of a defective alumina structure and (ii) an oxide capping layer preventing further oxidation at low temperature.     

Influence of minor alloying elements on the initial stages of oxidation of austenitic stainless steel materials

Surface oxidation of Fe‐19Cr‐17Ni, Fe‐19Cr‐18Ni‐1Al and TiC‐enriched Fe‐19Cr‐18Ni‐1Al alloys was investigated by photoelectron spectroscopy (PES). The experiments were conducted at 323 K in pure O₂ (2.7 × 10^?6 mbar). Composition and morphology of the nanoscale surface oxides were determined quantitatively by inelastic electron background analysis. Moreover, use of synchrotron radiation facilities were necessary to obtain improved sensitivity for studying minor alloying elements such as Al and Si. The results indicate oxygen‐induced segregation of Al, which significantly hinders the oxidation of the major alloying elements Fe and Cr. Ti remains in its inert carbide form. The relative concentration of Fe within the oxide layer was found to increase with the oxide‐layer thickness, indicating greater mobility of Fe relative to other alloying elements. Copyright © 2008 John Wiley & Sons, Ltd.     

Structural and morphological investigation of ceria-promoted Al(2)O(3) under severe reducing/oxidizing conditions

A series of CeO(2)/Al(2)O(3) samples with different ceria loadings in the range 0-25 wt % (0, 2, 5, 7.5, 15, and 25%) were prepared by incipient wetness and studied using several complementary techniques such as Brunauer-Emmett-Teller (BET), X-ray diffraction (XRD), temperature-programmed reduction (TPR), Raman, high-resolution transmission electron microscopy (HRTEM), and extended X-ray absorption fine structure (EXAFS). The aim of the investigation was to understand the behavior of ceria when deposited on alumina and treated under oxidizing and reducing conditions at high temperature (T >/= 1273 K). It is shown that ceria can partially stabilize alumina toward the formation of low-surface-area phases up to 1373 K under oxidizing conditions, while enhanced stabilization is observed under reducing conditions, being effective up to 1473 K. A detailed quantitative temperature-programmed reduction (TPR) analysis made at different loadings and calcination temperatures allowed us to identify three characteristic regions where the reduction of small and large ceria crystallites occurs with the formation of CeAlO(3) crystallites at high temperature. These are likely responsible for surface-area stabilization. For dispersed ceria samples, reduction takes place almost exclusively at low temperature (<700 K), while a shift to higher temperatures is observed upon increasing the ceria particle size. A fraction of Ce, in samples at low loadings, is stable in the lower oxidation state, even if subjected to strongly oxidizing conditions.     

Ba deposition and oxidation on theta-Al2O3/NiAl(100) ultrathin films. Part I: Anaerobic deposition conditions

Room-temperature Ba deposition on an oxygen-terminated theta-Al(2)O(3)/NiAl(100) ultrathin film substrate under ultrahigh vacuum (UHV) conditions is studied using X-ray photoelectron spectroscopy (XPS), Auger electron spectroscopy (AES) and temperature programmed desorption (TPD) techniques. In addition, Ba oxidation by the ions of the alumina substrate at 300 K < T < 1200 K in the absence of a gas-phase oxidizing agent is investigated. Our results indicate that at room temperature Ba grows in a layer-by-layer fashion for the first two layers, and Ba is partially oxidized. Annealing at T < 700 K results in further oxidation of the Ba species, whereas annealing at higher temperatures leads to loss of Ba from the surface via desorption and subsurface diffusion.     

给受体共混质量比对P3HT:PCBM薄膜结构和器件性能的影响

以聚3-己基噻吩(P3HT)为给体、[6,6]-苯基-C61-丁酸甲酯(PCBM)为受体的光伏体系作为研究对象,采用溶剂退火的后处理方法制备薄膜样品,利用紫外-可见(UV-Vis)吸收光谱、原子力显微镜(AFM)、X射线衍射(XRD)等测试手段分别对共混膜样品的形貌和结构进行表征,同时利用熵值统计方法对AFM形貌图像进行分析处理.并在此基础上制备太阳能电池器件,其结构为氧化铟锡导电玻璃/聚3,4-乙撑二氧噻吩:聚苯乙烯磺酸盐/聚3-己基噻吩:[6,6]-苯基-C61-丁酸甲酯/金属铝(ITO/PEDOT:PSS/P3HT:PCBM/Al),研究了给受体共混比例(质量比)对活性层薄膜以及电池性能的影响.结果表明,受体PCBM含量的增加会影响P3HT给体相的有序结晶,当给受体比例为1:1时,活性层薄膜具有较宽的紫外-可见吸收特征,且具有较好的相分离和结晶度,基于该样品制备的电池器件其光电转换效率达到三种比例的最大值(2.77%).表明退火条件下,改变给受体比例可以影响活性层的微纳米结构而最终影响电池的光电转换效率.     

Nature, density, and catalytic role of exposed species on dispersed VOx/CrOx/Al2O3 catalysts

The structure and surface composition of binary oxides consisting of CrO(x) and VO(x) dispersed on alumina and their effects on the rate and selectivity of oxidative dehydrogenation (ODH) of propane were examined and compared with those for CrO(x) and VO(x) dispersed on alumina. VO(x) deposition on an equivalent CrO(x) monolayer on alumina and deposition of CrO(x) on an equivalent monolayer of VO(x) deposited on alumina led to CrVO(4) species during thermal treatment with concomitant reduction of Cr(6+) to Cr(3+). Autoreduction of Cr(6+) to Cr(3+) is also detected for CrO(x), even without the presence of VO(x). Infrared spectroscopy of NO adsorbed at 153 K probes the relative abundance of alumina and of V(5+), Cr(3+), and Cr(6+) at surfaces. This technique detects differences in the surface composition of VO(x)/CrO(x)()/Al(2)O(3) and CrO(x)/VO(x)/Al(2)O(3). The first of these samples is enriched in VO(x) relative to CrO(x) compared with the second sample. Consistent with this finding, VO(x)/CrO(x)/Al(2)O(3) and CrO(x)/VO(x)/Al(2)O(3) are distinguishable in their ODH activities and propene selectivities. The highest ODH activity and propene selectivity is observed for VO(x)/CrO(x)/Al(2)O(3), which exhibits a surface enriched in VO(x) and having a low surface concentration of Cr(6+).     

Investigation of oxide films on ferritic stainless steel

Summary While annealing cold-rolled strip of ferritic stainless steel in protective atmosphere oxide films may form on the surface. These parts of strip are defective material because of their deteriorated workability and appearance. For detailed investigation of the structure of the oxide layers concerning chemical composition and thickness, they were analysed by SNMS, SEM, and chemical methods.The oxide layers which look yellowish, brown, blue or grey (annealing colours) have a max. thickness of 0.4 m. They consist of oxides of Cr, Mn, Si and Ti. Thickness, chemical composition, colour and the sequence of different oxides in the layer depend on annealing time, annealing temperature and the oxidation potential of the protective atmosphere.     

超薄层在白色有机电致发光器件中的应用

以DCJTB为掺杂剂, 以BCP为空穴阻挡层, 研究了两种结构的有机电致发光器件ITO/NPB/BCP/Alq3:DCJTB/Alq3/Al(结构A)和ITO/NPB/BCP/Alq3/Alq3:DCJTB/Alq3/Al(结构B)的电致发光光谱. 实验结果显示, 在结构A器件的电致发光光谱中, 绿光的相对发光强度较弱,增加Alq3层的厚度对绿光的相对发光强度的影响也很小; 而在结构B器件的电致发光光谱中, BCP层与掺杂层(Alq3:DCJTB)之间的Alq3薄层对绿光的相对发光强度影响显著, 用很薄的Alq3层就可以得到强的绿光发射. 进一步改变器件结构, 利用有机超薄层就可以得到稳定的白光器件ITO/NPB(50 nm)/BCP(3 nm)/Alq3(3 nm)/Alq3:DCJTB(1%(w))(5 nm)/Alq3(7 nm)/Al. 随着电压的增加(14-18 V), 该器件的色坐标基本保持在(0.33, 0.37)处不动; 在432 mA·cm-2的电流密度下, 该器件的发光亮度可达11521 cd·m-2.     

Effect of layer integrity of spin self-assembled multilayer films on surface wettability

We investigated the correlation between surface wettability and internal structure of polyelectrolyte (PE)/PE and PE/inorganic multilayer films prepared by the spin self-assembly (SA) method. Spin self-assembled poly(allylamine hydrochloride) (PAH)/poly(sodium 4-styrenesulfonate) (PSS) multilayer films deposited from PE solutions of 10 mM show the distinct oscillation in contact angles with variation of the outermost PE layer, representing the saturated values in contact angles of individual PAH and PSS layers. These contact angles are also well consistent with the angles measured from respective PE layers (i.e., PAH and PSS) of the spin SA (PAH/CdS-COO-) and (CdS-NH3+/PSS) films carrying the flat interface between PE and inorganic CdS nanoparticle layers as confirmed by X-ray reflectivity. Furthermore, based on the contact angle of CdS-NH3+ layer in the ordered (CdS-NH3+/PSS) films, the change in surface wettability of CdS-NH3+ layers of two different spin SA (CdS-NH3+/poly(methacrylic acid) (PMAA)) multilayer films with ordered and disordered internal structure is also investigated. The films with ordered and disordered internal structure were fabricated by the pH adjustment of PMAA. The CdS-NH3+ layer in both CdS-NH3+/PSS and CdS-NH3+/PMAA multilayer films with the ordered internal structure has the contact angle of about 25 +/- 2 degrees irrespective of the PSS or PMAA sublayer. As a result, the same surface wettability of PE or inorganic layers, despite different sublayers, strongly indicates that the spin SA method in optimum condition allows the top surface to be completely covered with a low level ofinterdigitation with a sublayer at each deposition step, and this leads to the conclusion that physical and chemical characteristics of the sublayers have no significant influence on those of the outermost layer.     

Rapid monitoring of the nature and interconversion of supported catalyst phases and of their influence upon performance: CO oxidation to CO2 by gamma-Al2O3 supported Rh catalysts

Spatially and temporally resolved energy-dispersive EXAFS (EDE) has been utilised in situ to study supported Rh nanoparticles during CO oxidation by O2 under plug-flow conditions. Three distinct phases of Rh supported upon Al2O3 were identified by using EDE at the Rh K-edge during CO oxidation. Their presence and interconversion are related to the efficiency of the catalysts in oxidising CO to CO2. A metallic phase is only found at higher temperatures (>450 K) and CO fractions (CO/O2 > 1); an oxidic phase resembling Rh2O3 dominates the active catalyst under oxygen-rich conditions. Below about 573 K, and in CO-rich environments, high proportions of isolated Rh(I)(CO)2 species are found to co-exist with metallic Rh nanoparticles. Alongside these discrete situations a large proportion of the active phase space comprises small Rh cores surrounded by layers of active oxide. Confinement of Rh to nanoscale domains induces structural lability that influences catalytic behaviour. For CO oxidation over Rh/Al2O3 there are two redox phase equilibria alongside the chemistry of CO and O adsorbed upon extended Rh surfaces.     

Oxide density distribution across the barrier layer during the steady state growth of porous anodic alumina films: chronopotentiometry, kinetics of mass and thickness evolution and a high field ionic migration model

The steady state growth of porous anodic alumina films in oxalate solutions at various conditions was studied by chronopotentiometry, mass balance and optical microscopy methods enabling determination of consumed Al, film mass and thickness, current efficiencies, Al³⁺ and O²⁻ transport numbers across barrier layer, etc. The film thickness growth rate was found to be proportional to O²⁻ anionic current. A high field ionic migration model was developed. It predicted that, during anodising, the local oxide density across barrier layer rises from 2.6 in Al|oxide to 4.59–5.22 g cm⁻³ in oxide|electrolyte interface with mean value ≈3.21–3.52 g cm⁻³. The field strength rises from the first to second interface. The mechanism of Al oxidation near the Al|oxide interface embraces the transformation of the Al lattice to a transient, rare oxide one sustained by field with comparable Al³⁺ spacing parameter. The oxide near the Al|oxide interface and around the density maximum in the oxide|electrolyte interface are under different levels of electro-restriction stresses. During relaxation, the oxide behaves like a solid-fluid material suppressing the initial density distribution.     

Investigations on current transients in porous alumina films during re-anodizing using the electrochemical quartz crystal microbalance

Current transients and mass variations in as-prepared and heat-treated anodic alumina films were measured during re-anodizing by means of voltammetry and electrochemical quartz crystal microbalance (EQCM), respectively. Aluminum electrodes (100 nm) on quartz crystals were prepared by thermal evaporation. Anodic alumina films were formed on the surface of Al electrodes in aqueous solutions of oxalic (0.3 M) and phosphoric (0.6 M) acid in the potentiostatic regime. The EQCM experiments did not detect an overshoot in the mass variation of the Al electrode during re-anodizing of heat-treated anodic alumina films. The observed current overshoot in transients proved the presence of electrons and electron holes injected from the contacts in the bulk of the oxide. This can be explained by the emergence of excess electrons in the barrier layer of the alumina films due to a change in the mobility of the electrons.     

H2 separation using defect-free, inorganic composite membranes

Defect-free, microporous Al(2)O(3)/SAPO-34 zeolite composite membranes were prepared by coating hydrothermally grown zeolite membranes with microporous alumina using molecular layer deposition. These inorganic composite membranes are highly efficient for H(2) separation: their highest H(2)/N(2) mixture selectivity was 1040, in contrast with selectivities of 8 for SAPO-34 membranes. The composite membranes were selective for H(2) for temperatures up to at least 473 K and feed pressures up to at least 1.5 MPa; at 473 K and 1.5 MPa, the H(2)/N(2) separation selectivity was 750. The H(2)/CO(2) separation selectivity was lower than the H(2)/N(2) selectivity and decreased slightly with increasing pressure; the selectivity was 20 at 473 K and 1.5 MPa. The high H(2) selectivity resulted either because most of the pores in the Al(2)O(3) layer were slightly smaller than 0.36 nm (the kinetic diameter of N(2)) or because the Al(2)O(3) layer slightly narrowed the SAPO-34 pore entrance. These composite membranes may represent a new class of inorganic membranes for gas separation.     

Density function theory study of CO adsorption on Fe3O4(111) surface

Density functional theory calculations have been carried out for CO adsorption on the Fe(oct2)- and Fe(tet1)-terminated Fe(3)O(4)(111) surfaces, which are considered as active catalysts in water-gas shift reaction. It is found that the on-top configurations are most stable on these two surfaces. Some bridge configurations are also stable in which the new C-O bond formed between the surface O atom and the C atom of CO. The adsorption on the Fe(oct2)-terminated surface is more stable than on the Fe(tet1)-terminated surface. The density of state reveals the binding mechanism of CO adsorption on the two surfaces. Our calculations have also shown that the absorbed CO can migrate from the on-top site to the bridge site or 3-fold site. The oxidation of CO via surface oxygen atoms is feasible, which is in good agreement with experimental results.     

Enrichment,incorporation and oxidation of copper during anodising of aluminium–copper alloys

Porous anodic oxides generated on copper‐containing aluminium alloys are less regular than anodic oxides generated on pure aluminium. Specifically, a porous oxide morphology comprising layers of embryo pores, generated by a cyclic process of oxide film growth and oxygen evolution, is generally observed. In this work, the relation between the oxidation behaviour of copper during anodising and the specific porous oxide film morphology was investigated by electrochemical techniques, transmission electron microscopy and Rutherford backscattering spectroscopy (RBS). It was found that the anodising potential determines the oxidation behaviour of copper, and the latter determines the porous oxide morphology. At low voltage, relatively straight pores with continuous cell walls were obtained on Al? Cu alloys, but selective oxidation of aluminium atoms resulted in the occlusion of copper‐containing metallic nanoparticles in the anodic film. At higher potentials, copper oxidation promoted oxygen evolution within the barrier layer, and generation of a less regular film morphology. RBS, performed on Al? Cu alloy specimens, revealed a high volume fraction of copper atoms in the anodic films generated at low potentials and a reduced amount of copper atoms in the anodic oxide films generated at high potentials. Copyright © 2009 John Wiley & Sons, Ltd.     

Rôle de la précipitation sur l'oxydation d'un alliage Fe-Cr-Al dans l'air à 1100° C

A study by thermo-gravimetry of the kinetics of oxidation of the alloy Fe-22Cr-4Al was carried out at 1100°C in ambient air, for durations up to 25 hours. The morphology of oxide scales formed at high temperature and the structure of oxide films were then observed and analyzed by scanning electron microscopy. The kinetic study, performed by thermo-gravimetry, showed the existence of two stages, of which only the second corresponds to a parabolic law, with the formation of a protective coating of αalumina. The presence in the alloy of foreign elements, added or not, led to the formation of precipitates whose distribution and number were studied by the analysis of metallographic images of surfaces. The influence of a preliminary cold work before oxidation was examined. The results showed that this mechanical treatment has no influence on the nature of the precipitates, but modifies their size. It comes out from this study that the nucleation and growth of these precipitates enter in competition with the formation of the layer of alumina, by accelerating the total oxidation rate during the first stage, and modify the morphology and the adherence of the formed alumina layer. The precipitates obtained at the interface have morphologies such that the internal stresses could then be modified considerably in terms of intensities and of distribution ; their relaxation would cause the warped state of the samples observed after oxidation.     

Effect of supporting surface layers on catalytic activities of gold nanoparticles in CO oxidation

The surfaces of fumed silica materials were modified with a surface sol-gel process for catalysis applications. This surface-modification approach allows not only a monolayer growth of TiO(2) or Al(2)O(3) but also a stepwise double-layer growth of TiO(2)/TiO(2), Al(2)O(3)/Al(2)O(3), TiO(2)/Al(2)O(3), or Al(2)O(3)/TiO(2) on the surfaces of the silica materials with a monolayer precision. XRD analyses revealed that the coated monolayers and double layers of TiO(2) and Al(2)O(3) were amorphous. Gold nanoparticles were successfully deposited on the above six surface-modified silica materials via a deposition-precipitation method. The catalytic activities of these six gold catalysts for CO oxidation are highly dependent on the structures of their surface monolayers or double layers. The gold catalyst supported on the silica material functionalized with a TiO(2) monolayer (Au/TiO(2)) is the most active in both as-synthesized and oxidized forms, while the gold catalyst supported on the silica material functionalized with an Al(2)O(3)/TiO(2) double layer (Au/Al(2)O(3)/TiO(2)/SiO(2)) is the most active in the reduced form among the six catalysts. Surprisingly, the gold catalyst supported on the silica material functionalized with a TiO(2)/Al(2)O(3) double layer (Au/TiO(2)/Al(2)O(3)/SiO(2)) has much less activity than Au/Al(2)O(3)/TiO(2)/SiO(2) under all various treatments, underscoring the sensitivity of the catalytic activity to the structure of the supporting surfaces.     

Ba deposition and oxidation on theta-Al2O3/NiAl(100) ultrathin films. Part II: O2(g) assisted Ba oxidation

Ba deposition on a theta-Al(2)O(3)/NiAl(100) substrate and its oxidation with gas-phase O(2) at various surface temperatures are investigated using X-ray photoelectron spectroscopy (XPS), Auger electron spectroscopy (AES), and temperature programmed desorption (TPD) techniques. Oxidation of metallic Ba by gas-phase O(2) at 800 K results in the growth of 2D and 3D BaO surface domains. Saturation of a metallic Ba layer deposited on theta-Al(2)O(3)/NiAl(100) with O(2)(g) at 300 K reveals the formation of BaO(2)-like surface states. These metastable peroxide (O(2)(2-)) states are converted to regular oxide (O(2-)) states at higher temperatures (800 K). In terms of thermal stability, BaO surface layers (theta(Ba) < 5 ML) that are formed by O(2)(g) assisted oxidation on the theta-Al(2)O(3)/NiAl(100) substrate are significantly more stable (with a desorption/decomposition temperature of c.a. 1050 K) than the thick (2 < theta(Ba) < 10 ML) metallic/partially oxidized Ba layers prepared in the absence of gas-phase O(2), whose multilayer desorption features appear as low as 700 K.     

In situ electro-deposition of Pt micro-nano clusters on the surface of {[PMo12O40]3-/PAMAM}n multilayer composite films and their electrocatalytic activities regarding methanol oxidation

The {[PMo(12)O(40)](3-)/PAMAM}(n) multilayer films are prepared by LBL electrostatic assembly technique, and their uniform and homogeneous traits have been verified by cyclic voltammetry. The {[PMo(12)O(40)](3-)/PAMAM}(n) multilayer films with PAMAM as the outmost layer, having an open structure and exhibiting good penetrability for the solvent molecules at low pH, are used as matrices for electro-deposition of Pt micro-nano clusters in situ. X-ray photoelectron spectroscopy (XPS) analysis and field emission scanning electron microscope (FE-SEM) characterization show that the unique Pt micro-nano clusters with flower-like structure have been immobilized on the surface of {[PMo(12)O(40)](3-)/PAMAM}(n) multilayer films. The morphologies of Pt micro-nano clusters are influenced by electro-deposition conditions such as deposition potential, deposition time, and the number of layers of {[PMo(12)O(40)](3-)/PAMAM}(n) multilayer films. Pt(-clusters)-{PMo(12)/PAMAM}(3) composite films demonstrate good electrocatalytic activities regarding methanol oxidation and improved tolerance of CO.