Synthetic Crystalline Calcium Silicate Hydrate (I): Cation Exchange and Caesium Selectivity

Summary.  Solid crystalline calcium silicate hydrate (I) synthesized from equimolar amounts of Ca and Si under hydrothermal conditions at 120°C shows cation exchange properties towards divalent metal cations such as Ni, Cu, Cd, or Hg. It also exhibits caesium selectivity in the presence of Na⁺. The exchange capacity and selectivity of the solid can be increased by 10 and 28%, respectively, upon substitution of 0.01 mol of the Ca²⁺ in its structure by Na⁺. The ability of metal cation uptake by the solid was found to obey the order Ni²⁺ > Hg²⁺ > Cu²⁺ > Cd²⁺. The different affinities of calcium silicate hydrate (I) towards these ions can be used for their separation from solutions and also in nuclear waste treatment. The mechanism of the exchange reaction is discussed. Received June 11, 2001. Accepted September 10, 2001     

The Thermal Dehydration of Magnesium Aluminum Pentafluoride Dihydrate: Crystal Structures of MgAlF5(H2O)2 and MgAlF5

Summary.  Small plate-like single crystals of MgAlF₅(H₂O)₂ have been obtained during hydrothermal treatment (270°C) of microcrystalline material prepared by precipitation of stoichiometric solutions of Al₂(SO₄)₃ ·  18H₂O and Mg(NO₃)₂ · 6H₂O with diluted hydrofluoric acid. The crystal structure of MgAlF₅(H₂O)₂ has been refined from single crystal data (Imma (# 74), Z = 4, a = 7.0637(7), b = 10.1308(10), c = 6.7745(7) ?, 398 structure factors, 33 parameters, R(F² > σ(F ²)) = 0.0245, wR(F² all) = 0.0525). Main features of the inverse weberite type structure are infinite chains of trans-bridged [AlF₆] octahedra which are connected via common fluorine atoms by isolated [MgF₄(H₂O)₂] octahedra. MgAlF₅(H₂O)₂ dehydrates at temperatures above 300°C to give MgAlF₅. XRPD analysis of this phase has revealed isotypism with FeAlF₅. The crystal structure of MgAlF₅ (Immm (# 71), Z = 2, a = 7.268(1), b = 6.123(2), c = 3.543(1) ?) is built of infinite chains of edge-sharing [MgF₆] octahedra and chains of corner-sharing [AlF₆] octahedra along [001]. Upon further heating to temperatures above 500°C, MgAlF₅ decomposes to MgF₂ and α − AlF₃. Received January 15, 2001. Accepted February 12, 2001     

Solvothermal Syntheses,Crystal Structures,and Properties of New [Mn(<Emphasis Type="BoldItalic">dien</Emphasis>)<Subscript>2</Subscript>]<Superscript>2+</Superscript> Complexes

Summary.  The two new compounds Mn(dien)₂[MoS₄] (1) and Mn(dien)₂[Mo₂O₂S₆] (2) (dien = diethylenetriamine) were prepared under solvothermal conditions. Both compounds were obtained as phase-pure products. The structures consist of new [Mn(dien)₂]²⁺ cations and isolated tetrahedral [MoS₄]²⁻ (1) or [Mo₂O₂S₆]²⁻ (2) anions. Between the anions and the cations, hydrogen bonding is observed. Compound 1 crystallizes in the tetragonal space group I (a = 10.219(2), c = 9.259(2) ?, Z = 2), whereas 2 crystallizes in the monoclinic space group P2₁/c (a = 8.703(2), b = 18.390(4), c = 14.603(3) ?, β = 103.18(3)°, Z = 4). The thermal behaviour of the thiomolybdates was investigated using difference thermoanalysis (DTA) and thermogravimetry (TG). Both compounds decompose under argon with a single endothermic signal in the DTA curve (peak maximum: 252 (1) and 242°C (2)). Received November 5, 2001. Accepted December 27, 2001     

Purification and Characterization of a Novel Collagenase from <Emphasis Type="Italic">Bacillus pumilus</Emphasis> Col-J

The collagenase, produced extracellular by Bacillus pumilus Col-J, was purified by ammonium sulfate precipitation followed by two gel filtrations, involving Sephadex G-100 column and Sepharose Fast Flow column. Purified collagenase has a 31.53-fold increase in specific activity of 87.33 U/mg and 7.00% recovery. The collagenase has a relative molecular weight of 58.64 kDa by sodium dodecyl sulfate-polyacrylamide gel electrophoresis. The optimal temperature for the enzyme reaction was 45 °C. More than 50% of the original activity still remained after 5 min of incubation at 70 °C or 10 min at 60 °C. The maximal enzyme activity of collagenase was obtained at pH 7.5, and it was stable over a pH range of 6.5–8.0. The collagenase activity was strongly inhibited by Mn²⁺, Pb²⁺, ethylenediamine tetraacetic acid, ethylene glycol tetraacetic acid, and β-mercaptoethanol. However, Ca²⁺ and Mg²⁺ greatly increased its activity. The collagenase from B. pumilus Col-J showed highly specific activity towards the native collagen from calf skin. The K _m and V _max of the enzyme for collagen were 0.79 mg/mL and 129.5 U, respectively.     

Kinetic Determination of Iodide Based on its Effect on the Hydrogen Peroxide Oxidation of Triflupromazine

Summary.  A new selective, sensitive, and simple kinetic method is developed for the determination of trace amounts of iodide. The method is based on the catalytic effect of iodide on the reaction of triflupromazine (TFP) with H₂O₂. The reaction is followed spectrophotometrically by tracing the oxidation product at 498 nm within 1 min after addition of H₂O₂. The optimum reaction conditions are TFP (0.4 × 10⁻³ M), H₂SO₄ (1.0M), H₃PO₄ (2.0M), and H₂O₂ (1.6M) at 30°C. Following this procedure, iodide can be determined with a linear calibration graph up to 4.5 ng ċ cm⁻³ and a detection limit of 0.04 ng ċ cm⁻³, based on the 3 S_b criterion. The method can also be applied to the determination of iodate and periodate ions. Determination of as little as 0.2, 1.0, 2.0, and 4.0 ng ċ cm⁻³ of I⁻, IO₃ ^-, or IO₄ ^- in aqueous solutions gave an average recovery of 98% with relative standard deviations below 1.6% (n = 5). The method was applied to the determination of iodide in Nile river water and ground waters as well as in various food samples after alkaline ashing treatment. The method is compared with other catalytic spectrophotometric procedures for iodide determination. Received January 19, 2001. Accepted (revised) March 12, 2001     

Preparation and Crystal Structure of K2Ag12Te7

Summary.  Single crystals of K₂Ag₁₂Te₇ (a = 11.460(2), c = 4.660(1) ?; V = 530.01 ?³; space group: P6₃/m; Z = 1) were synthesized under hydrothermal conditions at 250°C in concentrated aqueous KOH solution from elementary silver and tellurium. The crystal structure is characterized by trigonal prismatic KTe₆ polyhedra, connected via two common faces to KTe₃ rods parallel to [001]. These rods are combined by two crystallographically independent Ag atoms, each coordinated to four Te and three Ag atoms (Ag–Te and Ag–Ag < 3.1 ?) to a framework of the formula (K₂Ag₁₂Te₆)^2 + and with channels parallel to the sixfold axis. These channels are statistically occupied by one further Te atom per unit cell, distributed over two independent positions. Received May 17, 2001. Accepted (revised) July 3, 2001     

A Thermodynamic Study on the Binding of Calcium Ion with Myelin Basic Protein

The interaction of myelin basic protein (MBP) from the bovine central nervous system with divalent calcium ion was studied by isothermal titration calorimetry at 27 °C in aqueous solution. The extended solvation model was used to reproduce the enthalpies of Ca²⁺-MBP interaction over the whole range of Ca²⁺ concentrations. The solvation parameters recovered from the solvation model were attributed to the structural change of MBP due to the metal ion interaction. It was found that there is a set of two identical and non-interacting binding sites for Ca²⁺ ions. The association equilibrium constant is 0.021 μmol⋅dm⁻³. The molar enthalpy of binding is ΔH=−15.10 kJ⋅mol⁻¹.     

The Potential Energies of Cohesion of a Crystalline Organic Enantiomer and the Racemate; on the Energy for the Liquid Racemate [1]

Summary. The cohesion potential energy of the crystal of one enantiomer of ethyl 3-cyano-3-(3,4-dimethyloxyphenyl)-2,2,4-trimethylpentanoate, −47.7 ± 0.1 kJ mol⁻¹ (0–90°C), was found out from the heat of sublimation (123.2 ± 5.1 kJ mol⁻¹, 78.6°C) and the kinetic energies for the gas phase and the crystal. It was found that the entropy function of Debye’s theory of solids mathematically agreed with the vibrational entropy of the gas (variationally obtained), allowing to disclose the vibrational energy using the Debye energy function (E _vib 835.0 kJ mol⁻¹ (78.6°C), E ⁰ included). E _kin for the crystal (771.1 kJ mol⁻¹ (78.6°C)) was obtained by Debye’s theory with the experimental heat capacity. The cohesion energy represented a moderate part of the sublimation energy. The cohesion energy of the racemic crystal, −44.2 kJ mol⁻¹, was obtained by the heat of formation of the crystal in the solid state (3.0 kJ mol⁻¹, 83.3°C) and E _kin for the crystal (by Debye’s theory). The decrease in cohesion on formation of the crystal accounted for the energy of formation. The change in potential energy on liquefaction of the racemate from the gas state was disclosed obtaining added-up E _{vib + rot} for the liquid in the way as to E _vib for the gas, the Debye entropy function being increasedly suited for the liquid (E _{vib + rot} 763.4 kJ mol⁻¹ (115.4°C)). Positive ΔE _pot, 13.0 kJ mol⁻¹, arised from the increase in electronic energy (Δ _l ν_mean − 154.3 cm⁻¹, by the dielectric nature of the liquid), added to the cohesion energy.     

The interaction of double-charged metal ions with monolayers and bilayers of phospholipids

Electrophoretic mobilities of hexadecane/water emulsions containing dimyristoyl-phosphatidylcholine (DMPC) or egg yolk lecithin (EYL) monolayers at the interface and those of liposomes prepared from the same lipids were measured as functions of the concentrations of Ca²⁺, Mn²⁺, Cu²⁺, and Ni²⁺ cations in the aqueous phase. The surface potentials, surface charge densities (σ), and the Langmuir adsorption isotherms for various distances from the charged surface to the slip plane (d) were calculated on the basis of the Gouy-Chapman theory for 1∶2 electrolytes and the values of ζ-potentials. The binding constants (K) and parametersd were determined under the assumption that the maximum σ values correspond to one ion per phospholipid molecule at the interface. In the case of DMPC, the ion binding constants (L mol⁻¹) at 25°C are 230 and 87 for Ca²⁺, 31.5 and 21 for Mn²⁺, 11 and 6 for Cu²⁺, and 7.5 and 5.3 for Ni²⁺ in liposomes and emulsions, respectively. The affinities of Cu²⁺ and Ni²⁺ ions for EYL monolayers and bilayers are lower than those for DMPC mono- and bilayers. Thed parameters for all ions are smaller than the radii of the hydrated ions. In the case of Ca²⁺, Cu²⁺, and Ni²⁺, thed values for mono- and bilayers are different. The differences in K values between monolayers and bilayers as well as those between DMPC and EYL mono- and bilayers can be attributed to the differences in the local environment and orientation of the interfacial phosphate groups in these systems. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 12, pp. 2490–2495, December, 1998.     

Effects of Temperature and Common Ions on Binding of Puerarin to BSA

The effects of temperature and common ions on binding of puerarin to bovine serum albumin (BSA) are investigated. The binding constants (K _a) between puerarin and BSA are 1.13×10⁴ L⋅mol⁻¹ (20 °C) and 1.54×10⁴ L⋅mol⁻¹ (30 °C), and the number of binding sites (n) is (0.95±0.02). However, at a higher temperature (40 °C) the stability of the puerarin–BSA system decreases, which results in a lower binding constant (1.58×10³ L⋅mol⁻¹) and number of binding sites (n=0.73) of the puerarin–BSA system. However, the presence of Cu²⁺ and Fe³⁺ ions increases the binding constants and the number of binding sites in the puerarin–BSA complex.     

Conductometric and microcalorimetric analysis of the alkaline-earth/alkali-metal ion exchange onto polyacrylic acid

The specificity of the exchange between divalent (Di²⁺ = Ca²⁺ or Ba²⁺) and monovalent (M⁺ = Li⁺, Na⁺ or K⁺) ions onto a polyacrylic chain is examined using conductometric and microcalorimetric techniques. Assuming the formation of a bidentate complex between the Di²⁺ and the carboxylate groups, the conductometric data give the exchange ratio (Di²⁺/M⁺) and the speciation of the acrylic groups. No significant difference is observed between the three alkali-metal ions for a given Di²⁺ ion. Comparisons between Ca²⁺ and Ba²⁺ show a stronger hydrophobicity of the former as it precipitates at a complexation ratio r = 0.33 versus r = 0.45 for the Ba²⁺ salt. Microcalorimetric data show that all Di²⁺/M⁺ exchange energies are positive and depend significantly on the type of cations. The largest displacement energy (the more positive) is found for the binding of Ca²⁺ with sodium polyacrylate (8.13 kJ · mol⁻¹) and the smallest for Ba²⁺ with lithium polyacrylate (1.88 kJ · mol⁻¹). The interpretation of the data leads to the conclusion that specificity of the Di²⁺ binding originates in the dehydration phenomenon and specificity between the three alkali-metal ions is due to the decrease in the electrostatic bond strength with an increase in the ionic radii. The Di²⁺/M⁺ exchange is entropically driven. Received: 28 January 1999 Accepted in revised form: 7 April 1999     

Preparation,Thermal Behaviour,and Crystal Structure of MgAl<Subscript>2</Subscript>F<Subscript>8</Subscript>(H<Subscript>2</Subscript>O)<Subscript>2</Subscript>

Summary.  Single crystals of MgAl₂F₈(H₂O)₂ have been obtained under hydrothermal conditions (250°C, 14 d) from a starting mixture of AlF₃ and MgAlF₅(H₂O)₂ in a 5% (w/w) HF solution. The crystal structure has been determined and refined from single crystal data (Fmmm (#69), Z = 4, a = 7.2691(7), b = 7.0954(16), c = 12.452(2) ?, 281 structure factors, 27 parameters, R(F ² > 2σ (F ²)) = 0.0282, wR(F ² all) = 0.0885). The obtained crystals were systematically twinned according to (010/100/001) as twinning matrix, reflecting the pseudo-tetragonal metric. The crystal structure is composed of perowskite-type layers built of corner sharing AlF₆ octahedra with an overall composition of AlF₄ ⁻ which are connected via common fluorine atoms of [MgF_4/2(H₂O)_2/1] octahedra. Group-subgroup relations of MgAl₂F₈(H₂O)₂ to WO₃(H₂O)_0.33 and to other M(II)M(III)₂ F₈(H₂O)₂ structures are briefly discussed. Above 570°C, MgAl₂F₈(H₂O)₂ decomposes under elimination of water into α-AlF₃, β-AlF₃, and MgF₂. Received October 29, 2001. Accepted (revised) December 6, 2001     

High Level Expression of an Acid-Stable Phytase from <Emphasis Type="Italic">Citrobacter freundii</Emphasis> in <Emphasis Type="Italic">Pichia pastoris</Emphasis>

To obtain a high level expression of phytase with favorable characteristics, a codon-optimized phytase gene from Citrobacter freundii was synthesized and transferred into Pichia pastoris. Small-scale expression experiments and activity assays were used to screen positive colonies. After purified by Ni²⁺–NTA agarose affinity column, the characterizations of the recombinant phytase were determined. The recombinant phytase (r-phyC) had two distinct pH optima at 2.5 and 4.5 and an optimal temperature at 50 °C. It retained more than 80% activity after being incubated under various buffer (pH 1.5–8.0) at 37 °C for 1 h. The specific activity, Km, and Vmax values of r-phyC for sodium phytate were 2,072 ± 18 U mg⁻¹, 0.52 ± 0.04 mM, and 2,380 ± 84 U mg⁻¹ min⁻¹, respectively. The enzyme activity was significantly improved by 1 mM of K⁺, Ca²⁺, and Mg²⁺. These characteristics contribute to its potential application in feed industry.     

Study of Nd2–x Ce x CuO4?±?δ (x?=?0.1–0.25) as cathode material for intermediate-temperature solid oxide fuel cells

The solid solubility limit of Ce in Nd_2–x Ce _x CuO_4 ± δ , prepared by sol–gel process, is established up to x = 0.2. The transition from negative temperature coefficient to positive temperature coefficient, within the solid solubility region, is observed at 620 °C. The area-specific-resistance (ASR) is optimized for electrochemical cell sintered at 800 °C. ASR enhances with increase in sintering temperature of cell. ASR value of 0.93 ohm cm² at 700 °C, determined by electrochemical impedance spectroscopy is comparable against that by voltage versus current (V–I) characteristics at 0.98 ohm cm² at the same temperature. Electrochemical performance and ASR of Nd_1.8Ce_0.2CuO_4 ± δ is improved when prepared by sol–gel route over solid-state reaction, which is attributed to uniform size and shape of nanocrystalline grains.     

Rotational Energy Barrier of the Polarized Carbon–Carbon Double Bond in Quinophthalone

Summary.  A dynamic NMR effect is observed in the ¹³C NMR spectra of anhydrous quinophthalone (quinoline yellow) and its monohydrate in the vicinity of 47°C and 0°C, respectively, and is attributed to a restricted rotation around the polarized carbon–carbon double bond. The free energy of activation for this process in anhydrous quinophthalone and the monohydrate is 65±2 and 55±2 kJ · mol⁻¹, respectively, in CDCl₃. Received September 25, 2001. Accepted (revised) November 14, 2001     

Thermodynamic Study of the Binding of Mercury Ion to Human Growth Hormone at Different Temperatures

The interaction of human growth hormone (hGH) with the divalent mercury ion was studied by isothermal titration calorimetry at two temperatures of 27 °C and 37 °C in aqueous solutions. We found that there is a set of two identical and non-interacting binding sites for Hg²⁺ ions. The intrinsic dissociation equilibrium constant and the molar enthalpy of binding are 4.2 mmol⋅L⁻¹ and −14.8 kJ⋅mol⁻¹ at 27 °C and 5.1 mmol⋅L⁻¹ and −14.2 kJ⋅mol⁻¹ at 37 °C, respectively. The results obtained indicate that the stability of the protein increases due to the binding of mercury ions using the extended solvation theory.     

Study of sorption processes of strontium on the synthetic hydroxyapatite

The sorption of strontium on synthetic hydroxyapatite was investigated using batch method and radiotracer technique. The hydroxyapatite samples were prepared by a wet precipitation process followed by calcination of calcium phosphate that precipitated from aqueous solution. Also, commercial hydroxyapatites were used. The sorption of strontium on hydroxyapatite depended on the method of preparation and it was pH independent ranging from 4 to 9 as a result of buffering properties of hydroxyapatite. The distribution coefficient K _d was significantly decreased with increasing concentration of Sr²⁺ and Ca²⁺ ions in solution with concentration above 1 × 10⁻³ mol dm⁻³. The percentage strontium sorption for commercial and by wet method prepared hydroxyapatite was in the range of 83–96%, while calcined hydroxyapatite was ranging from 10 to 30%. The experimental data for sorption of strontium have been interpreted in the term of Langmuir isotherm. The sorption of Sr²⁺ ions was performed by ion-exchange with Ca²⁺ cations on the crystal surface of hydroxyapatite. Although calcined hydroxyapatite is successfully used as biomaterial for hard tissues repair, it is not used for the treatment of liquid wastes.     

A microchip sensor for calcium determination

A newly designed glass-PDMS microchip-based sensor for use in the determination of Ca²⁺ ions has been developed, utilizing reflectance measurements from arsenazo III (1,8-dihydroxynaphthalene-3,6-disulfonic acid-2,7-bis[(azo-2)-phenyl arsenic acid]) immobilized on the surface of polymer beads. The beads, produced from cross-linked poly(p-chloromethylstyrene) (PCMS), were covalently modified with polyethylenimine (PEI) to which the Arsenazo III could be adsorbed. The maximum amount of Arsenazo III which could be immobilized onto the PEI-attached PCMS beads was found to be 373.71 mg g⁻¹ polymer at pH 1. Once fabricated, the beads were utilized at the detection point of the microfluidic sensor device with a fiber optic assembly for reflectance measurements. Samples were mobilized past the detection point in the sensor where they interact with the immobilized dye. The sensor could be regenerated and re-used by rinsing with HCl solution. The pH, voltage, linear range, and the effect of interfering ions were evaluated for Ca²⁺ determination using this microchip sensor. At the optimum potential, 0.8 kV, and pH 9.0, the linear range of the microchip sensor was 3.57 × 10⁻⁵ – 5.71 × 10⁻⁴ M Ca²⁺, with a limit of detection (LOD) of 2.68 × 10⁻⁵ M. The microchip biosensor was then applied for clinical analysis of calcium ions in serum with good results. Electronic supplementary material Supplementary material is available in the online version of this article at and is accessible for authorized users.     

Significantly Improved Expression and Biochemical Properties of Recombinant Serratia marcescens Lipase as Robust Biocatalyst for Kinetic Resolution of Chiral Ester

A lipase gene from Serratia marcescens ECU1010 was cloned into expression vector pET28a, sequenced, and overexpressed as an N terminus His-tag fusion protein in Escherichia coli. Through the optimization of culture conditions in shake flask, the lipase activity was improved up to 1.09 × 10⁵ U/l, which is a great improvement compared to our previous reports. It was purified to homogeneity by Ni-NTA affinity chromatography with an overall yield of 59.4% and a purification factor of 2.4-fold. This recombinant lipase displayed excellent stability below 30 °C and within the pH range of 5.0−6.8, giving temperature and pH optima at 40 °C and pH 9.0, respectively. The lipase activity was found to increase in the presence of metal ions such as Ca²⁺, Cu²⁺, and some nonionic surfactants such as PEG series. In addition, among p-nitrophenyl esters of fatty acids with varied chain length, the recombinant lipase showed the maximum activity on p-nitrophenyl laurate (C₁₂). Using racemic trans-3-(4′-methoxy-phenyl)-glycidyl methyl ester [(±)-MPGM] as substrate, which is a key chiral synthon for production of diltiazem, a 50% conversion yield was achieved after 4 h in toluene–water (100 mM KPB phosphate buffer, pH 7.5) biphasic system (5:5 ml) at 30 °C under shaking condition (160 rpm), affording (−)-MPGM in nearly 100% ee. The K _m and V _max values of the lipase for (±)-MPGM were 222 mM and 1.24 mmol min⁻¹ mg⁻¹, respectively. The above-mentioned features make the highly enantioselective lipase from Serratia marcescens ECU1010 a robust biocatalyst for practical use in large-scale production of diltiazem intermediate.     

The Potential Energies of Cohesion of a Crystalline Organic Enantiomer and the Racemate; on the Energy for the Liquid Racemate [1]

The cohesion potential energy of the crystal of one enantiomer of ethyl 3-cyano-3-(3,4-dimethyloxyphenyl)-2,2,4-trimethylpentanoate, −47.7 ± 0.1 kJ mol⁻¹ (0–90°C), was found out from the heat of sublimation (123.2 ± 5.1 kJ mol⁻¹, 78.6°C) and the kinetic energies for the gas phase and the crystal. It was found that the entropy function of Debye’s theory of solids mathematically agreed with the vibrational entropy of the gas (variationally obtained), allowing to disclose the vibrational energy using the Debye energy function (E _vib 835.0 kJ mol⁻¹ (78.6°C), E ⁰ included). E _kin for the crystal (771.1 kJ mol⁻¹ (78.6°C)) was obtained by Debye’s theory with the experimental heat capacity. The cohesion energy represented a moderate part of the sublimation energy. The cohesion energy of the racemic crystal, −44.2 kJ mol⁻¹, was obtained by the heat of formation of the crystal in the solid state (3.0 kJ mol⁻¹, 83.3°C) and E _kin for the crystal (by Debye’s theory). The decrease in cohesion on formation of the crystal accounted for the energy of formation. The change in potential energy on liquefaction of the racemate from the gas state was disclosed obtaining added-up E _{vib + rot} for the liquid in the way as to E _vib for the gas, the Debye entropy function being increasedly suited for the liquid (E _{vib + rot} 763.4 kJ mol⁻¹ (115.4°C)). Positive ΔE _pot, 13.0 kJ mol⁻¹, arised from the increase in electronic energy (Δ _l ν_mean − 154.3 cm⁻¹, by the dielectric nature of the liquid), added to the cohesion energy.