Determination of nanomolar levels of guanine by differential-pulse adsorptive cathodic stripping voltammetry of its copper(II) complex

Guanine is determined at the 5.0×10^–10 –2.0×10^–7 mol/l level by differential-pulse adsorptive stripping voltammetry at a hanging mercury drop electrode using the reduction peak of its copper (II) complex at –0.21 V vs. Ag-AgCl electrode. The optimum analytical conditions were found to be Britton-Robinson buffer solution (pH 4.8), an accumulation potential of 0.0 V and an accumulation time of 3 min. Under these conditions, the detection limit is 5.0×10^–10 mol/l and the relative standard deviation 2.6% for 1.0×10^–7 mol/l guanine. The method is compared with the previous voltammetric methods. The presence of some purine derivatives does not interfere.     

Adsorptive stripping voltammetric determination of 1-(4′-bromophenyl)-3,3-dimethyltriazene

The optimum conditions were established for the determination of the genotoxic substance 1-(4-bromophenyl)-3,3-dimethyltriazene by differential-pulse voltammetry at a hanging mercury drop electrode in the concentration range 1 × 10^–4 to 1 × 10^–7 mol dm^–3. The sensitivity of the determination can be improved through adsorptive accumulation of the investigated substance on the surface of the hanging mercury drop electrode: differential pulse adsorptive stripping voltammetry can be used in the concentration range 1 × 10^–7 to 2 × 10^–10 mol dm^–3. The relative standard deviation (for ten determinations at 2 × 10^–10 mol dm^–3) was 7.5%.     

Differential pulse adsorptive stripping voltammetric determination of nickel and cobalt in high purity aluminium

A sensitive method for the simultaneous determination of trace amounts of nickel and cobalt in pure aluminium has been described using differential pulse adsorptive stripping voltammetry (DPASV) by adsorptive accumulation of the dimethyl glyoxime (DMG) complex on the hanging mercury drop electrode (HMDE). As supporting electrolyte 0.1 mol/l ammonia buffer, pH 9.0, containing ammonium citrate and 5×10^–4 mol/l DMG has been used. The determination limit obtained has been as low as 0.5 g/g for Ni and 0.2 g/g for Co (using about 100 mg sample) with a relative standard deviation of 13% and 22%, respectively.     

Adsorptive accumulation voltammetry of copper(II) using complex formation reaction with salicylideneamino-2-thiophenol

Summary The cathodic stripping voltammetry of copper(II) was investigated with a method, based on the adsorptive accumulation of the Cu(II)-salicylideneamino-2-thiophenol (SATP) complex on a hanging mercury drop electrode. The copper(II)-SATP complex could be accumulated on the electrode at –0.20 V in 0.01 mol/l nitric acid. The reduction peak of the copper complex was observed by scanning the potential in a negative direction in the differential pulse mode. The calibration curve for copper was linear over the range 5×10^–9–1×10^–7 mol/l. This method was applied to determine copper(II) in GSJ (Geological Survey of Japan) standard rock reference materials.     

Adsorptive voltammetric determination of the trace amount of cobalt

The synthesis of 5-Br-PADNm and the polarographic characteristics of this cobalt(II) complex are reported. In 0.15 mol/l sodium hydroxide cobalt(II) forms a 1 2 complex with 5-Br-PADNm. In the presence of 0.0030% Triton X-100 the complex gives an adsorptive polarographic wave at — 0.90 V, which is recommended for determination of cobalt down to 10^–10 mol/l. The proposed method has been applied to the trace cobalt in natural water, hair and tea samples, with a relative error less than 10%.     

Preconcentration and voltammetric determination of the herbicide metamitron with a silica-modified carbon paste electrode

A carbon paste electrode incorporating silica (Si-MCPE) was fabricated to accumulate Metamitron at the electrode surface. Several electroanalytical techniques were used to explore its reductive behaviour. The results indicate that the system is irreversible and fundamentally controlled by adsorption. The adsorptive stripping response has been evaluated with respect to accumulation time, deposition potential, scan rate, pH and other variables, using differential pulse voltammetry (DPV) and square wave voltammetry (SWV) as redissolution techniques. In both cases a voltammetric peak is obtained, at –0.542 V (DPV) and –0.421 V (SWV) in Britton-Robinson buffer (pH 1.9). The detection limits were 3.66 × 10^–1 M and 4.22 × 10^–9 M for AdS-DPV and AdS-SWV, respectively. Under optimum conditions the Metamitron reduction peak gave two linear regions in the range from 4.0 × 10^–9 M to 8.0 × 10^–8 M by means of AdS-DPV, with a coefficient of variation of 2.19% (n = 10) for 1 × 10^–8 M herbicide solution. A method was developed for determination of Metamitron in soils, with a recovery of 98.8% and a coefficient of variation of 5.26% (0.01 g/g of soil).     

Determination of dopamine in synthetic cerebrospinal fluid by SWV with a graphite–polyurethane composite electrode

This work describes an electroanalytical investigation of dopamine using cyclic voltammetry (CV) and the graphite–polyurethane composite electrode (GPU). In CV studies, well-defined redox peaks characterize the oxidation process at the GPU electrode, which is indicative of electrocatalytic effects associated with active sites on the GPU electrode surface. A new analytical methodology was developed using the GPU electrode and square wave voltammetry (SWV) in BR buffer solution (0.1 mol L^–1; pH 7.4). Analytical curves were constructed under optimized conditions (f=60s^–1, E_a=50 mV, E_I=2 mV) and detection and quantification limits of 6.4×10^–8 mol L^–1 (12.1 g L^–1) and 5.2×10^–6 mol L^–1 (0.9 mg L^–1), respectively, were achieved. The precision of the method was checked by performing ten successive measurements for a 9.9×10^–6 mol L^–1 dopamine solution. For intra-assay and inter-assay precisions, the relative standard deviations were 1.9 and 2.3%, respectively. In order to evaluate the developed methodology, the determination of dopamine was performed with good sensitivity and selectivity, without the interference of ascorbic acid in synthetic cerebrospinal fluid, which indicates that the new methodology enables reliable analysis of dopamine.     

Determination of traces of iron with the catalytic maximum wave in differential pulse polarography

Summary A differential pulse polarographic method for the determination of iron employing the catalytic maximum wave has been studied. A well-defined differential pulse polarographic peak for iron(III) in Britton-Robinson buffer solution containing 50 mol/l N-(2-hydroxyethyl) ethylenediamine N,N,N-triacetic acid (HEDTA) and 5 mmol/l KBrO₃ is observed in the potential range from +0.2 to –0.3 V vs. SCE. The peak current is very large compared to that of the Fe(III)/EDTA complex, being proportional to the concentration of iron(III) between 1.00×10^–8 and 3.58×10^–6 mol/l under optimum conditions. The relative standard deviations for 3.58×10^–7 mol/l and 1.79×10^–6 mol/l iron(III) were 1.38 and 0.54%, respectively (n=5), and the calculated detection limit was 5.2×10^–9 mol/l iron(III). The method has been applied to the determination of iron in fresh snow and rain waters.

---

Spurenbestimmung von Eisen mit Hilfe der katalytischen Maximumsstufe in der Differential-Puls-Polarographie

Zusammenfassung Das Verfahren beruht auf der Tatsache, daß in Britton-Robinson-Puffer (mit 50 mol/l HEDTA und 5 mmol/l KBrO₃) im Potentialbereich von +0,2 bis –0,3 V gegen SKE ein gut definierter puls-polarographischer Peak für Eisen(III) auftritt. Der Peakstrom ist im Vergleich zu dem des Fe(III)/EDTA-Komplexes sehr groß und ist unter optimalen Bedingungen im Konzentrationsbereich von 1,00·10^–8 bis 3,58·10^–6 mol/l der Eisen(III)-Konzentration proportional. Die relative Standardabweichung beträgt 1,38% bzw. 0,54% (n=5) für 3,58·10^–7 mol/l bzw. 1,79·10^–6 mol/l Fe(III). Die berechnete Nachweisgrenze liegt bei 5,2·10^–9 mol/l Fe(III). Das Verfahren wurde zur Eisenbestimmung in Schnee- und Regenwasser eingesetzt.

---

---

This work was supported in part by a Grant-in-Aid for Scientific Research from Hokkaido-prefecture, 1982.     

Accumulation voltammetry of copper(II) at carbon-paste electrode containing salicylideneamino-2-thiophenol

Summary Accumulation voltammetry of copper(II) was investigated with a carbon-paste electrode containing salicylideneamino-2-thiophenol(SATP). Copper(II) was accumulated as the copper(II)-SATP complex on the electrode without an applied potential by immersing the electrode in 0.01 mol/l acetate buffer (pH 3.8) containing copper(II). The reduction peak of the copper(II)-SATP complex was observed at –0.12 V (vs. SCE) in 0.01 mol/l acetate buffer (pH 3.8) by scanning the potential in a negative direction. The calibration curve for copper(II) was linear in the range of 2×10^–9–1×10^–7 mol/l. Since the accumulation of copper(II) is based on a chemical reaction between copper(II) and SATP, copper(II) was selectively accumulated on the electrode. The presented method was applied to the determination of copper(II) in standard reference materials prepared by the National Institute for Environmental Studies.     

Isotachophoretic analysis of the lipophilic cation tetraphenylphosphoniumbromide

Summary Tetraphenylphosphoniumbromide (TPP), a lipophilic cation used for the determination of plasma membrane potential, was quantified by isotachophoresis. The optimized leading electrolyte consisted of 10 mmol/l KOH as leading ion, supplemented with 0.5% hydroxy-ethylcellulose. The pH was adjusted to 9.5 with methionine. The terminating ion was 10 mmol/l tris(hydroxymethyl)-aminomethane (pH 9.2, adjusted with methionine). Leading ion concentrations of 10, 1 and 0.5 mmol/l respectively, showed nearly the same detection limits (2×10^–11 mol of TPP). This detection limit allowed the quantitative determination of TPP down to a concentration of 2 mol/l. Calibration curves in the range of 2×10^–11 to 1.5×10^–10 mol of TPP showed correlation coefficients greater than 0.95 (n=12; =0.01).     

Adsorptive stripping voltammetric determination of cobalt in the presence of dimethylglyoxime and cetyltrimethylammonium bromide

A sensitive procedure for determination of micro-traces of Co(II) by adsorptive stripping voltammetry is proposed. The procedure exploits the enhancement of the cobalt peak obtained by use of the system Co(II)–dimethylglyoxime–piperazine-1,4-bis(2-ethanesulfonic acid)–cetyltrimethylammonium bromide. Using the optimized conditions, a detection limit (based on the 3 criterion) for Co(II) of 1.2×10^–11 mol L^–1 (0.7 ng L^–1) was achieved. The calibration plot for an accumulation time of 30 s was linear from 5×10^–11 to 4×10^–9 mol L^–1. The procedure was validated by analysis of certified reference materials and natural water samples.     

Determination of dinoseb by adsorptive stripping voltammetry using a mercury film electrode

An adsorptive stripping voltammetric method for the determination of the pesticide dinoseb (2-sec.-butyl-4,6-dinitrophenol) at the mercury film electrode is described. The deposition of the mercury film on a glassy carbon disk electrode was optimized. The temperature, at which the mercury film was deposited, was demonstrated to have a strong influence on the stripping peaks, the first one being much more intense than the second. A systematic study of the variables affecting the stripping response was carried out by differential pulse voltammetry. The results obtained have been compared with those at the HMDE; a significant improvement in the sensitivity of the method developed with the MFE was observed. Using a 300 s accumulation time, the limits of determination and detection were 3.6 × 10^–10 and 1.1 × 10^–10 mol L^–1, respectively. The effect of the presence of several herbicides on the dinoseb response was also tested. The method has been applied to the determination of the pesticide in spiked apple juice at two concentration levels: 12.0 and 1.2 g L^–1 of juice.     

Determination of medecamycin by adsorptive stripping voltammetry with an activated electrode

The adsorptive and electrochemical behaviors of medecamycin were investigated on a glassy carbon electrode (GCE) pretreated by anodic oxidation at +1.8 V for 5 min in 0.025 mol l^–1 NH₃-NH₄Cl (pH 8.6) solution. An adsorptive stripping voltammetric method for the determination of medecamycin at the pretreated glassy carbon electrode has been developed. Medecamycin was accumulated in NH₃-NH₄Cl buffer (pH 9.0) at a potential of –0.7 V (vs. saturated calomel electrode (SCE)) for a certain time, and then determined by second-order differential anodic stripping voltammetry. The second-order differential anodic stripping peak current at +0.72 V was proportional to the concentration of medecamycin in the range 2.0 g ml^–1 to 50.0 g ml^–1. The detection limit (three times the signal-to-noise) was 1.0 g ml^–1 and the relative standard deviation of the results was 3.28% for eight successive determinations of 10.0 g ml^–1 medecamycin. This method has been applied to the direct determination of medecamycin in commercial tablets and spiked urine samples with satisfactory results.     

Adsorptive Voltammetric Study of Thorium–Alizarin Complexon Complex at a Carbon Paste Electrode

A new sensitive adsorptive voltammetric procedure is described for trace measurement of thorium. It is based on the cathodic stripping peak of the thorium–alizarin complexon (ALC) complex at a carbon paste electrode (CPE). The complex of Th(IV) with alizarin is adsorbed at a CPE in a mixed buffer solution (pH 5.0) which consists of 0.1mol·L^–1 sodium acetate and 0.04mol·L^–1 potassium biphthalate, yielding a sensitive cathodic voltammetric peak corresponding to the reduction of alizarin in the complex at –0.57V (vs. SCE). The second-order derivative peak current of the complex is linearly dependent upon the concentration of Th(IV) over the range of 3.0×10^–9 8.0×10^–7mol·L^–1. The detection limit is 1.0×10^–9mol·L^–1 for 180s accumulation. The molar ratio of each component in the complex was estimated as n_Th(IV):n_ALC=1:1 by a continuous variation method. The electrode processes of the Th(IV)–alizarin complex at a CPE were investigated. The procedure was successfully applied to the trace determination of thorium in ore and clay samples.     

Potentiometric determination of mercury(II) and thiourea in strong acid solution using an ion-selective electrode with AgI-based membrane hydrophobised by PTFE

Summary The potentiometric determination of mercury(II) and thiourea (TU) in strong acid solution (pH 0–1) by using an all-solid-state ion-selective electrode with (Ag₂S 25%, AgI 25% and PTFE 50% m/m)-membrane is described. The linear response, 43 mV(pHg)^–1 and 80 mV(pTU)^–1, has been obtained in the concentration range from 10^–2 to under 10^–5 mol/l. By direct potentiometry at pH 0 mercury(II) can be determined in the presence of up to 10^–3 mol/l of iron(III). The change in potential in the tested concentration range of thiourea indicates the formation of Ag(TU) _1.4 ⁺ at the exposed surface of the membrane. This stoichiometry is in good agreement with that calculated from the average Ag/TU ratio in the potentiometric titration. The investigated electrode can be used as a good sensor for mercury(II) and thiourea in strong acid media and a wide variety of practical analytical systems.     

Determination of Mo(VI) with 2-benzylideneiminobenzohydroxamic acid (2-BIBH) in urine by cathodic stripping voltammetry

Summary Controlled adsorptive accumulation of Mo(VI)-2-BIBH at the hanging mercury drop electrode (HMDE) provides the basis for the direct stripping measurement of Mo(VI) in nanomolar concentration. The cathodic stripping response is evaluated with respect to experimental parameters such as preconcentration time, preconcentration potential and others. A differential pulse cathodic stripping voltammetric method for the determination of Mo(VI) with 2-BIBH in urine is proposed. The detection limit is 10^–9 mol/l Mo(VI), standard deviation for 5×10^–8 mol/l is ±1.58×10^–9 mol/l.

---

Bestimmung von MolybdÄn(VI) mit 2-BenzylideniminobenzohydroxamsÄure (2-BIBH) in Harn durch kathodische Stripping-Voltammetrie

     

Determination of traces of vanadium with the catalytic maximum wave in differential pulse polarography

Summary A differential pulse-polarographic method has been studied for the determination of vanadium employing the catalytic maximum wave. A well-defined differential pulse polarographic peak is observed in the potential range from –0.2 to –0.7 V vs. SCE for vanadium(V) in 10 mmol 1^–1 NaCl containing 10 mmol 1^–1 acetic acid, 40 mmol 1^–1 pyrocatechol, and 2.5 mmol 1^–1 KBrO₃. The peak current is very large and proportional to the concentration of vanadium(V) between 1×10^–7 and 1×10^–6 mol 1^–1. The relative standard deviation at 0.5 mol l^–1 vanadium(V) was 2.06% (n=7). This method has been successfully applied to the determination of vanadium in standard materials such as pond sediment.

---

Spurenbestimmung von Vanadium mit Hilfe der katalytischen Maximumsstufe in der Differential-Puls-Polarographie

Zusammenfassung Ein gut definierter differentialpuls-polarographischer Peak wurde für Vanadium(V) in 10 mmol/l NaCl-Lösung, die 10 mmol/l Essigsäure, 40 mmol/l Brenzcatechin und 2,5 mmol/l KBrO₃ enthielt, beobachtet (Potentialbereich –0,2 bis –0,7 V gegen SCE). Der Peakstrom ist sehr groß und die Vanadiumkonzentration im Bereich von 1×10^–7 bis 1×10^–6 mol/l proportional. Die relative Standardabweichung betrug 2,06% (n=7) bei 0,5 mol/l Vanadium(V). Das Verfahren wurde mit gutem Erfolg zur Vanadiumbestimmung in Standardproben (z.B. Teichsediment) eingesetzt.

     

Determination of subnanomolar concentrations of cobalt by adsorptive stripping voltammetry at a bismuth film electrode

Procedures for trace cobalt determinations by adsorptive stripping voltammetry at in situ and ex situ plated bismuth film electrodes are presented. These exploit the enhancement of the cobalt peak obtained by using the Co(II)–dimethylglyoxime–cetyltrimethylammonium bromide–piperazine-N,N-bis(2-ethanesulfonic acid) system. The calibration graph for an accumulation time of 120 s was linear from 2 × 10^–10 to 2 × 10^–8 mol L^–1. The relative standard deviation from five determinations of cobalt at a concentration of 5 × 10^–9 mol L^–1 was 5.2%. The detection limit for an accumulation time of 300 s was 1.8 × 10^–11 mol L^–1. The proposed procedure was applied to cobalt determination in certified reference materials and in tap and river water samples.     

All-Solid-State PVC Membrane Ag+-Selective Electrodes Based on Diaza-18-Crown-6 Compounds

Two diaza-crown ether compounds were synthesized and evaluated as Ag⁺-selective carriers in polyvinylchloride (PVC) membrane electrodes of solid-state type. The all-solid-state PVC membrane electrode based on N,N-Dibenzyl-dibenzo-diaza-18-crown-6 exhibited a super-Nernstian response (75±10mV per decade) over the concentration range of 1×10^–1 to 7×10^–6M of Ag⁺ ion and a detection limit of 3×10^–6M, at a wide range of pH (pH 4–7). The response time of the electrode was fast (less than 10s), and it can be used for three months without any significant deviation in potential. The proposed all-solid-state PVC membrane electrodes revealed high selectivity toward Ag⁺ ion with respect to alkali, alkaline earth, heavy and transition metal ions. A flow-through cell of all-solid-state PVC membrane Ag⁺-selective electrode based on N,N-Dibenzyl-dibenzo-diaza-18-crown-6 has also been prepared and applied for flow-injection analysis of Ag⁺ ion in solution.     

Spectrophotometric and derivative spectrophotometric determination of copper (II) with dithizone in aqueous phase

A Spectrophotometric and derivative Spectrophotometric study of Cu-dithizonate complex in aqueous phase in the presence of Triton X-100, a neutral surfactant, is reported. The system obeys Beer's law between 1.0 × 10^–6–9.0 × 10^–6 mol/l of Cu²⁺; detection limit is 12 ng/ml. The molar absorption coefficient, specific absorptivity and Sandell's sensitivity of the complex are 3.06 × 10⁴ 1 mol^–1 cm^–1, 0.4825 ml g^–1 cm^–1 and 2.1 × 10^–3 g cm^–2, respectively. The conditional stability constant of the 1 2 complex, calculated considering simultaneously existing equilibria, has been found to be 1.73 × 10¹¹ I² mol² (I = 0.07, pH 1.4, temperature = 10 °C). Absorption studies in the derivative mode have been carried out to determine the absorption maximum of the complex and to overcome interference due to the presence of certain metal ions. The method has been validated by determination of copper in beers, wines, human hair, goat liver and fly ash samples.