ZnO/C纳米球的亚甲基蓝单吸附特性:平衡、动力学及机理

采用电弧放电法制备了ZnO/C纳米球,利用FESEM、XRD和N₂吸附/脱附测试进行了表征。在避光条件下研究了复合材料对亚甲基蓝的吸附性能。研究结果表明,随着亚甲基蓝的浓度及接触时间的增长吸附量明显上升,在吸附时间为150 min时达到吸附平衡。采用Langmuir、Freundlich及Temkin等温吸附模式对吸附平衡进行了研究。结果表明,吸附等温线符合Langmuir等温吸附模式,单层吸附饱和容量可达188.68 mg·g^-1。利用动力学模型、内扩散模型和外扩散速率控制模型拟合实验数据,拟合数据表明其动力学符合伪二级动力学模型;内扩散机理不是吸附速率的唯一限制机理,亚甲基蓝的总吸附速率受膜扩散控制。     

ZnO/C纳米球的亚甲基蓝单吸附特性:平衡、动力学及机理（英文）

采用电弧放电法制备了Zn O/C纳米球,利用FESEM、XRD和N2吸附/脱附测试进行了表征。在避光条件下研究了复合材料对亚甲基蓝的吸附性能。研究结果表明,随着亚甲基蓝的浓度及接触时间的增长吸附量明显上升,在吸附时间为150 min时达到吸附平衡。采用Langmuir、Freundlich及Temkin等温吸附模式对吸附平衡进行了研究。结果表明,吸附等温线符合Langmuir等温吸附模式,单层吸附饱和容量可达188.68 mg·g-1。利用动力学模型、内扩散模型和外扩散速率控制模型拟合实验数据,拟合数据表明其动力学符合伪二级动力学模型;内扩散机理不是吸附速率的唯一限制机理,亚甲基蓝的总吸附速率受膜扩散控制。     

氧化锆-活性炭纤维复合材料的制备及其对F-吸附性能

采用水热合成法成功制备了氧化锆-活性炭纤维复合材料,并研究了其对F^-的吸附行为.表征结果表明,复合材料中氧化锆粒子成功负载于活性炭纤维上.吸附实验结果表明,负载了氧化锆的活性炭纤维对F^-有高效的去除效率,其吸附机理包括离子交换和静电作用力,吸附等温线符合Langmuir等温吸附模式,吸附动力学可用拟二级动力学模型拟合.吸附量随着溶液pH的升高而降低,共存离子Cl^-、NO₃^-和SO₄^2-对F^-在氧化锆-活性炭纤维复合材料上的吸附几乎没有影响.     

氧化锆-活性炭纤维复合材料的制备及其对F-吸附性能

采用水热合成法成功制备了氧化锆-活性炭纤维复合材料,并研究了其对F^-的吸附行为。表征结果表明,复合材料中氧化锆粒子成功负载于活性炭纤维上。吸附实验结果表明,负载了氧化锆的活性炭纤维对F^-有高效的去除效率,其吸附机理包括离子交换和静电作用力,吸附等温线符合Langmuir等温吸附模式,吸附动力学可用拟二级动力学模型拟合。吸附量随着溶液pH的升高而降低,共存离子Cl^-、NO₃^-和SO₄^2-对F^-在氧化锆-活性炭纤维复合材料上的吸附几乎没有影响。     

高岭土磁性复合材料表面印迹聚合物选择性吸附分离环丙沙星

以氨基改性的磁性高岭土为基质材料,利用电子转移产生催化剂的原子转移自由基聚合法制备磁性高岭土表面印迹聚合物（MMIPs）。通过FTIR、TEM、TGA、XRD和VSM等方法对其物理化学性质进行表征,其比表面积112 m²·g^-1,且具有较好的热稳定性、超顺磁性（M_s=13.365 emu·g^-1）。吸附性能研究表明,准二级动力学模型能较好地描述MMIPs对环丙沙星（CIP）吸附动力学行为,Langmuir等温模型能较好地拟合MMIPs对CIP的吸附平衡数据,25℃时MMIPs的单分子层吸附容量为89.36 mg·g^-1。选择性实验研究表明,MMIPs对CIP具有较好地选择识别性。结合高效液相色谱分析技术,MMIPs已成功应用于鲜鱼样品中痕量CIP的分离、富集和回收,CIP的回收率为92.15%。     

二氧化硅/氧化锌复合体系的制备及其去除亚甲基蓝和罗丹明B研究

利用溶剂热法,以正硅酸乙酯为硅源,硝酸锌为锌源一次性合成了二氧化硅/氧化锌(SiO₂/ZnO)复合材料,利用傅里叶红外光谱和X射线衍射对其结构进行了表征分析,研究了该复合材料对亚甲基蓝和罗丹明B的吸附性能。结果表明,SiO₂/ZnO可快速去除水中的亚甲基蓝和罗丹明B,并在20 min内达到吸附平衡,SiO₂/ZnO对亚甲基蓝的吸附速率和吸附量均高于罗丹明B。吸附动力学研究表明,SiO₂/ZnO对亚甲基蓝和罗丹明B的吸附动力学均符合准二级动力学方程。等温吸附数据分析表明,Langmuir比Freundlich模型能更好地拟合亚甲基蓝和罗丹明B的吸附过程,由Langmuir计算得到亚甲基蓝和罗丹明B的单层饱和吸附量分别为235.3 mg/g和100.1 mg/g。此外,SiO₂/ZnO具有良好的重复使用性能,经过5次吸附-脱附循环后,其对亚甲基蓝的吸附能力仍保持在80%以上。     

稻壳基活性炭对亚甲基蓝吸附平衡与动力学研究

以粮食副产物——稻壳为原料,采用化学活化法制成了微介孔共存的孔隙发达的稻壳基活性炭,此稻壳基活性炭对亚甲基蓝的吸附量可以达到464.8 mg·g-1。通过大量亚甲基蓝吸附实验结果拟合,发现其吸附平衡过程符合Freundlich吸附模型,动力学模型符合准二级吸附动力学模型。通过吸附平衡模型与动力学模型的建立,为此活性炭的实际应用提供理论预测模板。     

芭蕉芋渣对亚甲基蓝的吸附及机理研究

以芭蕉芋渣作为吸附材料,探讨了pH值、温度、亚甲基蓝(MB)初始质量浓度、吸附时间等因素对其吸附MB的影响,利用FT-IR、SEM等技术,结合吸附等温线和动力学模型分析研究了其吸附机理。结果表明,芭蕉芋渣能与阳离子染料亚甲基蓝上的正电荷基团之间形成静电引力,从而产生较好的吸附作用,亚甲基蓝的起始浓度在100～5 000 mg/L,吸附量达到185.0 mg/g。随吸附时间的增加,芭蕉芋渣对亚甲基蓝的去除率增大,180 min后达到平衡;随着温度的升高,吸附量也增大。芭蕉芋渣对亚甲基蓝的吸附作用更符合Redlich-Peterson等温模型;该吸附动力学过程可以用准二级模型进行很好的描述,拟合所得的初始吸附速率随着温度的增加而提高。     

以铬皮为原料制备多孔炭及其对亚甲基蓝的吸附性能研究

以铬皮为原料制备多孔炭,并考察其对亚甲基蓝染料的吸附性能,对其吸附机理进行了探讨。结果表明,体系pH、亚甲基蓝初始浓度和吸附时间对多孔炭吸附亚甲基蓝的能力影响较大。通过吸附等温线和吸附动力学研究,发现该吸附过程可用Langmuir吸附等温线来描述,且符合准二级动力学吸附模型。铬皮基多孔炭有望成为含亚甲基蓝污水处理的良好净化剂。     

氨基化锰铁氧体纳米粒子的制备及吸附pb2+和Cd2+性能研究

利用一步水热法合成了氨基化锰铁氧体纳米粒子吸附材料,并研究了对Pb₂₊和Cd₂₊的吸附特性和去除效果;通过SEM、XRD、 FT-IR和XPS等方法进行了表征分析和吸附机理研究。结果表明：温度为25 ℃,氨基化锰铁氧体纳米粒子吸附Pb₂₊和Cd₂₊在60 min内即可达到吸附平衡,最大饱和吸附量分别为255.57 mg?g_-1和129.72 mg?g_-1;吸附过程符合准二级动力学方程和Langmuir等温吸附方程,对Pb₂₊和Cd₂₊的吸附过程主要是单分子层化学吸附。氨基化锰铁氧体纳米粒子吸附-再生重复利用5次后,对Pb₂₊和Cd₂₊的吸附量分别仍为初始吸附量的87%以上,表现了良好的再生吸附性能。     

Removal of methylene blue by seed-watermelon pulp-based low-cost adsorbent: Study of adsorption isotherms and kinetic models

Based on the abundance of seed-watermelon pulp (SWP) in Xinjiang, China, SWP was employed to prepare low-cost adsorbent toward the removal of methylene blue (MB). The effects of contact time at different initial concentration were studied. The widely used adsorption isotherm models including Langmuir, Freundlich, and Temkin isotherms were employed to depict the adsorption process. The Langmuir isotherm was best fitted to the experimental data. Batch kinetic studies showed that an equilibrium time of 300 minutes was needed for the adsorption. The adsorption properties can be well described by pseudo-second-order kinetic model and the MB uptake was not controlled by intraparticle diffusion mechanism.     

Competitive Adsorption of Methylene Blue and Rhodamine B on Natural Zeolite: Thermodynamic and Kinetic Studies

A batch system was applied to study the adsorption behavior of methylene blue (MB) and rhodamine B (RB) in single and binary component systems on natural zeolite. In the single component systems, the zeolite presents higher adsorption capacity for MB than RB with the maximal adsorption capacity of 7.95×10^?5 and 1.26×10^?5 mol/g at 55°C for MB and RB, respectively. Kinetic studies indicated that the adsorption followed pseudo‐second‐ order kinetics and could be described by a two‐step diffusion process. For the single component systems, the adsorption isotherm could be fitted by the Langmuir model. In the binary component system, MB and RB exhibit competitive adsorption on the zeolite. The adsorption is approximately reduced to 50% and 60% of single component adsorption systems of MB and RB, respectively at an initial concentration of 6×10^?6 mol·L^?1 at 25°C. In the binary component system, kinetic and adsorption isotherm studies demonstrate that the experimental data are following pseudo‐second‐order kinetics and Langmuir isotherm and kinetic data are fairly described by a two‐step diffusion model. Effect of solution pH on adsorption of MB and RB in both single and binary component systems was studied and the results were described by electrostatic interactions.     

Fabrication and optimization calix[8]arene-PbS nanoadsorbents for the adsorption of methylene blue: Isotherms,kinetics and thermodynamics studies

The present study aims to determine the adsorption behaviour of methylene blue (MB) dye based on calix[8]arene-modified lead sulphide (PbS) nanoadsorbents under optimal conditions. Response surface methodology (RSM) was executed to evaluate the interactive effect of three factors (adsorbent dosage, contact time, and pH) on the adsorption of MB dye using a central composite design (CCD). The optimised values for adsorbent dosage, contact time, and pH solution were found to be 45.00 mg of calix[8]arene-modified PbS, contact time of 180 min, and pH 6. This study reports the results of batch adsorption experiments, which include the adsorption capacity, kinetics, and isotherm of the MB adsorption process. Pseudo-first order and pseudo-second order were demonstrated for their quality to fit the data. Pseudo-second order was the best in fitting the adsorption data with the higher R² values (R² > 0.928), indicating chemisorption to be the mechanism of adsorption. The Langmuir and Freundlich equilibrium models were employed to determine the isotherm parameters. The equilibrium assessment illustrated that the Langmuir isotherm model fitted well with the adsorption data, and a maximum MB adsorption capacity of 11.90 mg/g was achieved. The characterisation studies with EDX, FESEM, and FTIR indicated a successful synthesis of calix[8]arene-modified PbS.     

Theoretical,Equilibrium, Kinetics and Thermodynamic Investigations of Methylene Blue Adsorption onto Lignite Coal

The interaction of methylene blue (MB) dye with natural coal (collected from coal landfills of the Kosovo Energy Corporation) in aqueous solutions was studied using adsorption, kinetics, and thermodynamic data, and Monte Carlo (MC) calculations. In a batch procedure, the effects of contact duration, initial MB concentration, pH, and solution temperature on the adsorption process were examined. The Langmuir, Freundlich, Temkin, and Dubinin–Radushkevich (D–R) isotherms were used to examine the equilibrium adsorption data. The equilibrium data fit well to the Freundlich and Langmuir adsorption isotherm models; however, the Freundlich model suited the adsorption data to a slightly better extent than the Langmuir model. The kinetics experimental data was fitted using pseudo-first-order, first-order, pseudo-second-order, second-order, Elvoich equation, and diffusion models. The pseudo-second-order rate model manifested a superlative fit to the experimental data, while the adsorption of MB onto coal is regulated by both liquid film and intraparticle diffusions at the same time. Thermodynamic parameters, such as Gibbs free energy (ΔG⁰), enthalpy (ΔH⁰), and entropy (ΔS⁰) were calculated. The adsorption of MB was confirmed to be spontaneous and endothermic. The theoretical results were in agreement with the experimental ones.     

Cationic dye adsorption by poly(N-isopropylacrylamide/maleic acid) copolymeric hydrogels prepared by gamma rays

N-isopropylacrylamide/maleic acid hydrogels containing different quantities of maleic acid have been synthesized with γ-radiation. The hydrogels were used in experiments on swelling, diffusion and adsorption of a cationic dye methylene blue. The diffusion of MB into the hydrogels was found to be the non-Fickian type. The factors influencing adsorption capacity of the hydrogel such as gel composition, and irradiation dose were systematically investigated. The equilibrium data for dye adsorption was better described by the Freundlich isotherm than Langmuir isotherm model. The kinetic studies showed that the pseudo-second-order kinetic model fits better than the data obtained from pseudo-first-order model.     

Preparation and Characterization of Activated Carbon Fiber from Paper

Activated carbon fibers (ACFS) with surface area of 1388 m²/g prepared from paper by chemical activation with KOH has been utilized as the adsorbent for the removal of methy-lene blue from aqueous solution. The experimental data were analyzed by Langmuir and Freundlich models of adsorption. The effects of pH value on the adsorption capacity of ACFS were also investigated. The rates of adsorption were found to conform to the kinetic model of Pseudo-second-order equation with high values of the correlation coefficients (R>0.998). The Langmuir isotherm was found to fit the experimental data better than the Feundlich isotherm over the whole concentration range. Maximum adsorption capacity of 520 mg/g at equilibrium was achieved. It was found that pH played a major role in the adsorption process, higher pH value favored the adsorption of MB.     

Fabrication of carboxymethyl functionalized β-cyclodextrin-modified graphene oxide for efficient removal of methylene blue

In this study, a novel carboxymethyl functionalized β-cyclodextrin-modified graphene oxide (CM-β-CD-GO) adsorbent was designed and fabricated. The CM-β-CD-GO was applied to remove methylene blue (MB) from aqueous solutions. The adsorption mechanism was discussed in detail through the study of pH effect, kinetics, and isotherm models. The adsorption of CM-β-CD-GO for MB displayed high removal rates at the pH range of 6.0–10.0, and the removal efficiency is over 90% within 20 min. The pseudo-second-order model could well describe the kinetic process of MB adsorption, and the adsorption was determined by the multi-step process. The maximum uptake capability of CM-β-CD-GO towards MB was 245.70 mg g⁻¹ at 25 °C according to Langmuir isotherm model. A possible adsorption mechanism that electrostatic attraction, π-π interaction, and host-guest supramolecular interactions supported MB adsorption was proposed. The adsorption capacity of CM-β-CD-GO showed no significant change after five cycles. The structure and morphology of CM-β-CD-GO were characterized by XPS, FT-IR, TGA, PXRD, AFM, SEM, zeta (ζ) potential determination, and Raman spectroscopy. This work provides valuable information for the design of novel adsorbents that specifically and efficiently adsorb cationic dyes contaminants.     

Multi‐responses optimization of simultaneous adsorption of methylene blue and malachite green dyes in binary aqueous system onto Ni:FeO(OH)‐NWs‐AC using experimental design: derivative spectrophotometry method

In this research, response surface methodology (RSM) approach using Central Composite Design (CCD) coupled by derivative spectrophotometry method was applied to develop mathematical model and optimize process parameters for simultaneous adsorption of methylene blue (MB) and malachite green (MG) from aqueous solution using Ni:FeO(OH) ‐ NWs‐AC. The optimal conditions to adsorption of MB and MG in binary mixture solution from aqueous solution were found at pH 8.0, MB concentration 20 mg L^‐1, MG concentration 20 mg L^‐1, adsorbent dosage 0.033 g and contact time 40 min. At these conditions, high adsorption efficiency (99.39% and 100.0% for MB and MG, respectively) was achieved. Among experimental equilibrium, Langmuir isotherm model fitted well with maximum monolayer adsorption capacity of 28.6 and 29.8 mg g^‐1 for MB and MG, respectively. The adsorption kinetic data followed pseudo second‐order kinetics for MB and MG dyes.     

Comparative adsorption of methylene blue by magnetic baker’s yeast and EDTAD-modified magnetic baker’s yeast: Equilibrium and kinetic study

Magnetic baker’s yeast (MB) was prepared using glutaraldehyde cross-linking method and chemical modification with ethylenediaminetetraacetic dianhydride (EDTAD). The fabricated EDTAD-modified magnetic baker’s yeast (EMB) was then employed to remove methylene blue. Comparative adsorption of methylene blue by EMB and MB was systematically investigated with respect to pH, contact time, initial concentration and reaction temperature. The mechanism of methylene blue adsorption by EMB and MB was investigated by SEM, FTIR and Special surface area using methylene blue method. The results revealed that Fe₃O₄ nanoparticles were steadily cross-linked/incorporated with baker’s yeast biomass and the EDTA was modified on the surface of the magnetic baker’s yeast. The equilibrium adsorption data were fitted better by Langmuir isotherm, and the specific surface areas were 42.953–226.07 m²/g for MB and 94.972–499.85 m²/g for EMB, respectively. Kinetic studies suggested that the pseudo-second-order model was suitable to describe the adsorption process. Thermodynamic studies indicated that the adsorption was feasible, spontaneous and endothermic. The recovery efficiencies were above 80% by using 0.1 M HCl.