基于氧化铒石墨烯氧化物复合纳米材料的葡萄糖氧化酶直接电化学性能及对葡萄糖的检测

将稀土纳米材料Er₂O₃用于构建葡萄糖生物传感器。Er₂O₃和氧化石墨烯形成复合基底,将葡萄糖氧化酶（GOD）固载在玻碳电极表面。首先利用SEM和XRD技术对所制备的Er₂O₃和氧化石墨烯纳米材料进行表征。利用EIS和CV对整个生物传感器制备过程进行表征。Er₂O₃的存在能有效地保持GOD的生物活性并加速其与电极之间的电子传递。由于Er₂O₃和氧化石墨烯之间的协同效应,使得制备的传感器在CV图中呈现一对明显的氧化还原峰,证实GOD和电极之间的直接电子传递性能。当用于对葡萄糖的电催化氧化时,传感器的CV响应随着葡萄糖浓度的增加而变弱。在葡萄糖浓度为1~10 mmol·L^-1范围内,CV响应值与葡萄糖浓度成线性关系。此外,传感器具有好的稳定性和重现性。     

基于氧化铒-石墨烯氧化物复合纳米材料的葡萄糖氧化酶直接电化学性能及对葡萄糖的检测（英文）

将稀土纳米材料Er_2O_3用于构建葡萄糖生物传感器。Er_2O_3和氧化石墨烯形成复合基底,将葡萄糖氧化酶(GOD)固载在玻碳电极表面。首先利用SEM和XRD技术对所制备的Er_2O_3和氧化石墨烯纳米材料进行表征。利用EIS和CV对整个生物传感器制备过程进行表征。Er_2O_3的存在能有效地保持GOD的生物活性并加速其与电极之间的电子传递。由于Er_2O_3和氧化石墨烯之间的协同效应,使得制备的传感器在CV图中呈现一对明显的氧化还原峰,证实GOD和电极之间的直接电子传递性能。当用于对葡萄糖的电催化氧化时,传感器的CV响应随着葡萄糖浓度的增加而变弱。在葡萄糖浓度为1~10 mmol·L-1范围内,CV响应值与葡萄糖浓度成线性关系。此外,传感器具有好的稳定性和重现性。     

试验优化设计Er3+-Yb3+共掺杂Gd2Ti2O7上转换发光特性

采用溶胶-凝胶（Sol-gel）法制备了Er³⁺-Yb³⁺共掺杂Gd₂Ti₂O₇纳米晶粉末,通过试验优化设计的理论建立了Er³⁺-Yb³⁺掺杂浓度与发光强度的回归方程,利用遗传算法优化计算出方程的最优解Er³⁺、Yb³⁺掺杂浓度分别为5.60%（物质的量分数）和13.43%。Er³⁺-Yb³⁺共掺杂Gd₂Ti₂O₇纳米晶粉末为单一面心立方Gd₂Ti₂O₇相结构,随Yb³⁺共掺杂浓度增加,X射线衍射峰逐渐向高角偏移。在976 nm激光激发下,Er³⁺-Yb³⁺共掺杂Gd₂Ti₂O₇获得了分别对应于Er³⁺的²H_11/2/⁴S_3/2→⁴I_15/2和⁴F_9/2→⁴I_15/2跃迁的绿色和红色上转换发光,且绿色和红色发光均为双光子吸收过程。研究了最优样品上转换发光与温度之间的关系,发现绿色上转换发光具有优良的温度传感特性,对红色上转换发光的温度猝灭进行了解释。     

还原氧化石墨烯/金纳米修饰电极在新冠病毒检测中的应用

研究使用电化学沉积法在丝网印刷碳电极表面制备了还原氧化石墨烯和金纳米颗粒,构建了一种用于新冠病毒检测的石墨烯电化学传感器。通过扫描电子显微镜(SEM)和相应的电化学方法对纳米复合材料在电极表面的成功修饰进行了表征分析。并采用差分脉冲伏安法对传感器的性能进行检测,实验构建的电化学传感器具有良好的灵敏度,该传感器检线性范围为10_-10^-10_-6^mol/L,具有良好的重复性和特异性。     

Gd2O3:Er3+上转换发光粉在染料敏化太阳电池中的应用

采用沉淀-煅烧法制备了Gd₂O₃:Er³⁺上转换发光粉,通过X射线衍射、扫描电子显微镜、能谱和荧光光谱对其进行了表征,并利用该发光粉具有上转换发光的特性将其应用于染料敏化太阳电池(DSSC)。结果表明,管状Gd₂O₃:Er³⁺上转换发光粉可增加电池对太阳光的吸收范围和吸收效率,提高电池的光电流和光电压。研究了掺杂量对电池性能的影响,当掺杂量为5wt%时,光电转换效率从5.93%升高到7.55%,提高约27%。     

球形微粒Co3O4电极催化氧化硫离子

尝试用氨蒸发诱导合成方法在石墨小片上生长球形Co₃O₄微粒, 并用其制备电极且进行S^2-的电化学氧化研究. 用极化曲线、恒电位技术等电化学方法考察了Co₃O₄电极对S^2-的电化学氧化的催化性能, 发现Co₃O₄电极对电化学氧化S^2-具有优异的催化性能, 极大地促进了-0.40 V 附近S^2-向含硫的酸根离子和低级多硫离子的转变, 电流密度最大可以达到580 mA·cm^-2. 恒电位极化表明电极的电催化稳定性良好; 电化学阻抗谱(EIS)测试显示Co₃O₄在碱性S^2-电解液中的电荷转移电阻很小, 这从电化学动力学角度解释了它对S^2-具有良好的催化性能.     

Ni/NiCo2O4电极的制备及其析氧反应性能

采用溶胶-凝胶法制备NiCo₂O₄尖晶石粉体, 然后以多孔Ni 为基体, 通过复合溶胶涂覆结合烧结制备Ni/NiCo₂O₄ 涂层电极. 运用扫描电子显微镜(SEM)、能量色散谱(EDS)和X 射线衍射(XRD)表征粉体以及Ni/NiCo₂O₄涂层电极的组成和结构. 采用循环伏安(CV), 稳态极化(LSV), 电化学阻抗谱(EIS), 恒电位阶跃以及恒电位长时间电解研究涂层电极在5 mol·L^-1 KOH溶液中的电催化析氧反应(OER). 结果表明: Ni/NiCo₂O₄涂层电极与多孔Ni 电极对比, 具有低的析氧过电位、高的比表面积和高的稳定性能; 其中比表面积增大了28.69倍,表观活化能在不同过电位分别降低了166.78和162.15 kJ·mol^-1.     

双金属Ag-Cu枝晶的制备及应用

通过铜箔基体上电沉积泡沫铜结合伽尔瓦尼置换反应制备出了银-铜(Ag-Cu)纳米枝晶, 利用X射线衍射(XRD)和场发射扫描电子显微镜(FE-SEM)对枝晶的成分及形貌进行研究发现, 随着沉积过电位的增加, 铜的前驱体形貌由棒状到枝晶状, 最后发展为泡沫状, 但泡沫状的前驱体制备的Ag-Cu 枝晶却是最规整和致密的. 另外, 银离子的浓度也会影响枝晶的形貌, 一定范围内浓度的增加有利于枝晶的形成. 通过线性扫描伏安和电流-时间曲线对制备的Ag-Cu 枝晶催化性能进行表征, 在电解质溶液中, -0.25 V(相对于饱和甘汞电极(SCE))时有一个明显的双氧水(H₂O₂)还原峰, 这意味着Ag-Cu枝晶对H₂O₂的电还原具有较好的催化活性, 当该电极被用于双氧水传感器时, 电流响应快, 能在3 s 内达到稳态电流, 线性测量范围为0.1-12 mmol·L^-1, 灵敏度可以达到330.36 μA·(mmol·L^-1)^-1·cm^-2, 这点对于提高传感器的准确性非常重要.     

球形纳米Fe3O4的制备及超级电容性能研究

采用双氧水氧化水热法制备Fe₃O₄,通过IR、XRD和SEM对样品的结构和性能进行表征。结果表明,产物为形貌规整的球形,平均粒径为25 nm。通过恒流充放电、循环伏安和交流阻抗等方法研究Fe₃O₄电极的电容性能。电化学测试表明,在1 mol·L^-1 Na₂SO₃溶液中,-1.2～0.2 V(vs SCE)电位范围内,Fe₃O相似文献   

自组装型Pt/γ-Al2O3催化剂用于低温去除挥发性有机物

分别通过自组装法(AS)和浸渍法(WI)制备得到纳米催化剂Pt/γ-Al₂O₃-AS和Pt/γ-Al₂O₃-WI, 并用于评价甲苯、异丙醇、丙酮、乙酸乙酯等易挥发性有机物(VOCs)的氧化性能. 通过各种表征手段探究了催化剂形态、结构及表面性质与催化剂氧化活性的关系. 结果表明, Pt/γ-Al₂O₃-AS在低温下即可实现VOCs的完全氧化. 在气体浓度(体积分数)为1000×10^-6, 空速为18000 mL·g^-1·h^-1的条件下, 甲苯、异丙醇、丙酮、乙酸乙酯被Pt/γ-Al₂O₃-AS催化剂完全氧化的温度分别为130、135、145、215℃, 展现出了优异的氧化性能, 且具有很好的稳定性. 该催化剂较高的比表面积、较小的Pt纳米粒径、较好的Pt纳米颗粒分散度、更好的低温还原效果及丰富的表面羟基是具有较高催化活性的重要因素.     

Preparation of Co3O4/graphene Oxide Composites by a Depositing‐decompostion Method and its Application for Electrochemical Determination of Glucose

Co₃O₄/graphene oxide (GO) nanocomposites were successfully prepared by a depositing‐decomposition method. The as‐prepared samples were characterized by scanning electron microscopy (SEM) and Raman spectroscopy. Cyclic voltammetry (CV) was used to evaluate the electrochemical response of a glass carbon electrode (GCE) modified with Co₃O₄/GO nanocomposite towards glucose. Compared with the Co₃O₄/GCE, the Co₃O₄/GO/GCE exihibits higher electrocatalytic activity due to the synergistic effects of electrocatalytic ability of Co₃O₄ and large surface of GO. The Co₃O₄/GO/GCE was applied for glucose detection in alkaline solution. The linear current response range of glucose on Co₃O₄/GO/GCE covered the range from 9 × 10^?5 to 6.03 × 10^?3 M, with a detection limit of 5.2 × 10^?7 M (S/N = 3).     

ZnO/In2O3复合空心球的制备及其光电催化葡萄糖降解性能

通过葡萄糖协助的水热以及随后的退火处理两步法成功制备了系列ZnO/In₂O₃复合空心球. X射线衍射谱(XRD)表明, 经500 ℃退火制得的ZnO/In₂O₃复合空心球中ZnO以非晶态存在, 但是随着退火温度的提高, 其逐渐转变为纤锌矿结构. 场发射扫描电子显微镜(FE-SEM)和透射显微镜(TEM)结果表明, ZnO/In₂O₃复合材料具有空心球结构, 复合纳米颗粒之间结合紧密. 将ZnO/In₂O₃复合空心球组装成薄膜光电极, 研究了其光电催化降解葡萄糖的性能. 结果表明, 700 ℃退火处理的ZnO/In₂O₃复合空心球薄膜电极可产生最高的光致电流密度. 通过光致发光光谱(PL)发现, 与ZnO或In₂O₃空心球相比, ZnO/In₂O₃复合空心球的发光强度猝灭效果明显. 这是由于复合材料中晶界处产生的p-n结电场, 降低了光生电子-空穴对的复合几率, 从而使更多的光生电子可迁移到电极表面.     

Magnetic solid-phase extraction based on Fe3O4/graphene oxide nanoparticles for the determination of malachite green and crystal violet in environmental water samples by HPLC

This work describes a magnetic Fe₃O₄/graphene oxide (GO)-based solid-phase extraction (MSPE) technique for high performance liquid chromatography (HPLC) detection of malachite green (MG) and crystal violet (CV) in environmental water samples. Fe₃O₄/ GO magnetic nanoparticles were synthesised by a chemical co-precipitation method and characterised by scanning electron micrograph, transmission electron microscope, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy and surface area analyser. The prepared Fe₃O₄/GO magnetic nanoparticles were used as the adsorbents of MSPE for MG and CV. By coupling with HPLC, a sensitive and cost-effective method for simultaneous determination of MG and CV was developed. The important parameters including the amount of Fe₃O₄/GO, pH of the sample solution, extraction time, salt effect, the type and volume of desorption solvent were investigated in detail. Under optimised conditions, the calibration curves were linear in the concentration range of 0.5–200 μg L^?1, and the limits of detection were 0.091 and 0.12 μg L^?1 for MG and CV, respectively. Finally, the established MSPE-HPLC method was successfully applied to determine MG and CV in environmental water samples with the recoveries ranging from 91.5% to116.7%.     

Facile Fabrication of a Graphene‐based Electrochemical Biosensor for Glucose Detection

A simple and effective glucose biosensor based on immobilization of glucose oxidase (GOD) in graphene (GR)/Nafion film was constructed. The results indicated that the immobilized GOD can maintain its native structure and bioactivity, and the GR/Nafion film provides a favorable microenvironment for GOD immobilization and promotes the direct electron transfer between the electrode substrate and the redox center of GOD. The electrode reaction of the immobilized GOD shows a reversible and surface‐controlled process with the large electron transfer rate constant (k_s) of 3.42±0.08 s^?1. Based on the oxygen consumption during the oxidation process of glucose catalyzed by the immobilized GOD, the as‐prepared GOD/GR/Nafion/GCE electrode exhibits a linear range from 0.5 to 14 mmol·L^?1 with a detection limit of 0.03 mmol·L^?1. Moreover, it displays a good reproducibility and long‐term stability.     

SiO2 coated Fe3O4 magnetic nanoparticle dispersed multiwalled carbon nanotubes based amperometric glucose biosensor

A new type of amperometric glucose biosensor based on silicon dioxide coated magnetic nanoparticle decorated multiwalled carbon nanotubes (Fe₃O₄@SiO₂/MWNTs) on a glassy carbon electrode (GCE) has been developed. MWNTs have been synthesized by catalytic chemical vapour decomposition (CCVD) of acetylene over rare earth (RE) based AB₃ alloy hydride catalyst. The as-grown MWNTs have been purified and further functionlized. Functionalized MWNTs have been decorated with magnetic Fe₃O₄ nanoparticles which have been uniformly coated with biocompatible SiO₂ using a simple chemical reduction method. The characterization of magnetic nanoparticle modified MWNTs have been done by X-ray diffraction (XRD), Fourier transform infra red spectroscopy (FT-IR), scanning electron microscope (SEM), transmission electron microscope (TEM), vibrating sample magnetometer (VSM), energy dispersive X-ray analysis (EDX) and UV-vis spectroscopy. Amperometric biosensor has been fabricated by the deposition of glucose oxidase (GOD) over Nafion-solubilized Fe₃O₄@SiO₂/MWNTs electrode. The resultant bioelectrode retains its biocatalytic activity and offers fast and sensitive glucose quantification. The performance of the biosensor has been studied using cyclic voltammetry and amperometry and the results have been discussed. The fabricated glucose biosensor exhibits a linear response from 1 μM to 30 mM with an excellent detection limit of 800 nM indicating the potential applications in food industries.     

Glucose Biosensor Using Glucose Oxidase and Electrospun Mn2O3‐Ag Nanofibers

The highly porous Mn₂O₃‐Ag nanofibers were fabricated by a facile two‐step procedure (electrospinning and calcination). The structure and composition of the Mn₂O₃‐Ag nanofibers were characterized by SEM, TEM, XRD, EDX and SAED. The as‐prepared Mn₂O₃‐Ag nanofibers were then employed as the immobilization matrix for glucose oxidase (GOD) to construct an amperometric glucose biosensor. The biosensor shows fast response to glucose, high sensitivity (40.60 µA mM^?1 cm^?2), low detection limit (1.73 µM at S/N=3), low K_m,app value and excellent selectivity. These results indicate that the novel Mn₂O₃‐Ag nanfibers‐GOD composite has great potential application in oxygen‐reduction based glucose biosensing.     

CuTAPc-Fe3O4纳米复合粒子及其漆酶固定化研究

漆酶的固定化研究对基于漆酶催化的光纤生物传感器具有十分重要的意义. 制备了四氨基酞菁铜(CuTAPc)-Fe₃O₄纳米复合粒子, 并用红外(IR)、场发射扫描电镜(FEG-SEM)、X射线衍射(XRD)、能谱、粒径仪等对其进行了表征. 结果表明形成了以CuTAPc包覆在Fe₃O₄纳米粒子表面的纳米复合粒子, 粒子呈现不规则球形, 且分布均匀, 粒子平均粒径在50 nm左右. 用此纳米复合粒子通过戊二醛交联法固定了漆酶, 固定后的酶比游离酶具有更好的贮存稳定性及操作稳定性. 这为研制高性能的光纤生物传感器打下了较好的基础.     

基于二氧化钛/碳纳米管/壳聚糖纳米复合薄膜制备葡萄糖生物传感器

利用壳聚糖(CHI)溶液分散了纳米二氧化钛(nano-TiO2)和多壁碳纳米管(MWCNT),将该分散液修饰于玻碳电极表面形成纳米复合薄膜;用戊二醛为交联剂在该纳米复合层上固定了葡萄糖氧化酶(GOx),同时以二茂铁为电子媒介体构建了一种新型葡萄糖传感器。利用扫描电镜(SEM)、交流阻抗(AC)对所制备的传感器进行了表征,同时用循环伏安法(CV)和计时电流法(CA)考察了其对葡萄糖的电催化氧化性能。实验结果表明,在优化测试条件下该传感器对葡萄糖在0.5～20.0 mmol.L-1范围内有线性响应,检出限为0.2 mmol.L-1;电流达到95%的稳态时间小于5 s;此生物传感器具有良好的重现性和选择性,能有效排除抗坏血酸、尿酸等常见干扰物的影响并成功应用于饮料中葡萄糖含量的测定。     

Er~(3+)∶V_(0.01)Y_(2.99)Al_5N_(0.01)F_(0.01)O_(11.98)/BiPO_4/Pt光催化剂的制备及其在降解废水中亚甲基蓝的应用

通过溶胶-凝胶法合成了上转换发光材料Er~(3+)∶V_(0.01)Y_(2.99)Al_5N_(0.01)F_(0.01)O_(11.98)(Er∶YAG),然后利用水热法合成了BiPO_4,再利用高温煅烧法合成了Er∶YAG/BiPO_4/Pt复合物光催化剂.通过使用X-射线粉末衍射仪(XRD),扫描电子显微镜(SEM),透射电子显微镜(TEM),光致发光光谱(PL)和上转换发射光谱对样品的组成、形貌及光学特征进行了表征.此外,还研究了不同甘油添加量、 Er∶YAG和BiPO_4的摩尔比例和复合温度及光催化剂的循环使用次数对Er∶YAG/BiPO_4/Pt复合物光催化剂活性的影响.实验结果显示Er∶YAG/BiPO_4/Pt复合物光催化剂具有高的光催化活性和较好的稳定性,它可以作为一种高效的光催化剂用于污水中有机污染物的处理.