Effect of NaOH on large-volume sample stacking of haloacetic acids in capillary zone electrophoresis with a low-pH buffer

Large-volume sample stacking (LVSS) is an effective on-capillary sample concentration method in capillary zone electrophoresis, which can be applied to the sample in a low-conductivity matrix. NaOH solution is commonly used to back-extract acidic compounds from organic solvent in sample pretreatment. The effect of NaOH as sample matrix on LVSS of haloacetic acids was investigated in this study. It was found that the presence of NaOH in sample did not compromise, but rather help the sample stacking performance if a low pH background electrolyte (BGE) was used. The sensitivity enhancement factor was higher than the case when sample was dissolved in pure water or diluted BGE. Compared with conventional injection (0.4% capillary volume), 97-120-fold sensitivity enhancement in terms of peak height was obtained without deterioration of separation with an injection amount equal to 20% of the capillary volume. This method was applied to determine haloacetic acids in tap water by combination with liquid-liquid extraction and back-extraction into NaOH solution. Limits of detection at sub-ppb levels were obtained for real samples with direct UV detection.     

On-line flow sample stacking in a flow injection analysis-capillary electrophoresis system: 2000-fold enhancement of detection sensitivity for priority phenol pollutants

A flow injection analysis-capillary electrophoresis system has been used for on-line flow stacking of 11 US Environmental Protection Agency priority phenol pollutants. Samples containing low concentrations of phenols dissolved in deionised water are continuously delivered to the capillary opening by means of a peristaltic pump. The sample components stack at the boundary between the highly conductive separation electrolyte and the introduced sample. By selecting an appropriate electrolyte and stacking conditions the movement of the electrolyte solution inside the capillary can be reduced, thereby improving the stacking efficiency. The electrolyte used here contained 20 mM phosphate, 8% 2-butanol, and 0.001% hexamethonium bromide at pH 11.95, and the stacking was carried out at 2 kV for 240 s. These conditions allowed up to 2000-fold preconcentration of the selected phenols. No matrix removal was necessary.     

Flow injection-capillary electrophoresis system with contactless conductivity detection and hydrostatic pressure generated flow. Application to the quantitative analysis of inorganic anions in water samples

A simple and inexpensive flow injection-capillary electrophoresis (FI-CE) system with contactless conductivity detection (CCD) for automated quantitative analysis of chloride, nitrate, and sulfate in various water samples is demonstrated. A glass bottle containing the background electrolyte that is raised above the FI-CE interface generates a pulse-free, highly reproducible flow of the electrolyte through the FI-CE interface. The system operates at a flow rate of 300 microLmin(-1) with an injection volume of only 4 microL. The repeatability of peak areas (n = 18) was better than 0.81% RSD and the sample throughput was 90 samples per hour using the background electrolyte containing 12 mM L-histidine adjusted to pH 4.00 with acetic acid. The limits of detection were better than 125 microgL(-1) and were comparable to those obtained by conventional CE systems with CCD. Various calibration methods for FI-CE system with electrokinetic injection were tested and their suitability for the analysis of anions in real samples was evaluated.     

Capillary electrophoresis for the determination of new markers of natural latex quality

Nowadays, increasing use of latex products in the healthcare area has also led to an increase in new scientific controls of raw material and manufactured products in order to maintain higher standards in quality control. Since field latex is a rich environment for microbial growth, in the absence of adequate preservation, the carbohydrates that it contains become microbiologically oxidised to the so-called volatile fatty acids (VFAs). Samples of natural rubber latex coming from different countries and processed in different ways have been tested by applying a capillary electrophoresis method for the measurement of the short-chain organic acids present in sera. The separation was performed with phosphate buffer at pH 6.25 and cetyltrimethylammonium bromide (CTAB) as background electrolyte in an uncoated fused-silica capillary with -10 kV of applied potential. The sample needs no other pre-treatment more than coagulation to obtain the serum. In the assayed samples, it has been shown that poorly-preserved latex presented higher amounts of succinic acid and lower amounts of malic acid. The succinic to malic acid ratio may be an important parameter because it cannot be altered by dilution or similar processes such as the traditional VFA index, used to determine the quality of latex. Ratios for succinic to malic acid <0.6 have been found for well-preserved latex and >0.6 for poorly-preserved latex.     

Simultaneous determination of inorganic and organic anions,alkali, alkaline earth and transition metal cations by capillary electrophoresis with contactless conductometric detection

Simultaneous separation of up to 22 inorganic and organic anions, alkali, alkaline earth and transition metal cations was achieved in less than 3 min in the capillary electrophoresis system with contactless conductometric detector. The sample was injected from both capillary ends (dual opposite end injection) and anionic and cationic species were detected in the center of the separation capillary. The parameters of the separation electrolyte, such as pH, concentration of the electrolyte, concentration of complexing agents and concentration of 18-crown-6 were studied. Best results were achieved with electrolytes consisting of 8 mM L-histidine, 2.8 mM 2-hydroxyisobutyric acid, 0.32 mM 18-crown-6 at pH 4.25 or 9 mM L-histidine, 4.6 mM lactic acid, 0.38 mM 18-crown-6 at pH 4.25. Other electrolytes containing complexing agents such as malic or tartaric acid at various concentrations could also be used. The detection limits achieved for most cations and anions were 7.5 - 62 micro gL(-1) except for Ba2+ (90 micro gL(-1)), Cd 2+, Cr 3+ and F- (125 micro gL(-1)), and fumarate (250 micro gL(-1)). The repeatability of migration times and peak areas was better than 0.4% and 5.9%, respectively. The developed method was applied for analysis of real samples, such as tap, rain, drainage and surface water samples, plant exudates, plant extracts and ore leachates.     

Quantitative analysis of microcystin variants by capillary electrophoresis mass spectrometry with dynamic pH barrage junction focusing

Dynamic pH junction is an online focusing method in CE based on the electrophoretic mobility difference of analytes in the sample matrix and the background electrolyte. An advantage of this method over the conventional CE is that the sensitivity can be significantly improved. By injecting a long sample plug in the capillary and focusing the analytes at the pH boundary between the background electrolyte and sample matrix, the LOD can be improved by 10–100 folds. The dynamic pH junction method can be easily coupled with ESI‐MS. In this work, we used this method for the analysis of microcystins (MCs). The detection limits and dynamic ranges were studied. The separation was optimized by adjusting the injection time, and concentrations and pH values of the background electrolyte. The optimization of analyte focusing leads to enhanced detection response compared to conventional injections, achieving 200–400 fold higher averaged peak heights for four microcystin (MC) variants. More importantly, this method was successfully used for the quantitative analysis of microcystins (MCs) in crude algae samples from natural water bodies, making it promising for practical applications.     

Crosslinking of cotton cellulose with succinic acid in the presence of titanium dioxide nano-catalyst under UV irradiation

The nanometer titanium dioxide (TiO₂), succinic acid (SUA), and the mixture of nano- TiO₂ and SUA were dispersed or dissolved in pure water, then irradiated with UV at the wavelength of 254 nm under stirring for different time periods respectively. The pH and conductivity values and UV-vis spectra of those solutions were recorded immediately. The powders obtained from the filtrated and vacuum dried from those solutions were examined with Fourier Transform Infrared Spectroscopy and Wide Angle X-Ray Diffraction meter. It shows that the crystalline structure and IR and UV-vis spectra of SUA adsorbed on nano-TiO₂ particles are changed. The photo-reduced succinic acid in the presence of nanometer titanium dioxide under UV irradiation can create aldehyde group on SUA and free radical of SUA to improve the catalytic effects of crosslinking reaction between SUA and cotton cellulose.     

Simultaneous Determination of Organic Acids in Wine Samples by Capillary Electrophoresis and UV Detection: Optimization with Five Different Background Electrolytes

A simple technique is described for the routine capillary electrophoretic determination of organic acids in wine samples. Several aromatic and non‐aromatic compounds, including phthalic acid, benzoic acid, sorbic acid, boric acid, and phosphate, were evaluated as background electrolytes in order to obtain the highest resolution and detection sensivity. Factors that affect capillary electrophoretic separation such as the concentration and pH of the background electrolyte (BGE), the concentration of the electroosmotic flow modifier (EOF), and methanol addition to the electrolyte were investigated systematically. Tartaric, malic, succinic, acetic, and lactic acids were determined simultaneously in approximately six minutes using an electrolyte containing 3 mM phosphate and 0.5 mM myristyltrimethylammonium bromide (MTAB) as electroosmotic flow modifier at pH 6.5. This method is quantitative, with recoveries in the 90–102% range and linear up to 50 mg L^–1. The precision is better than 1% and the procedure shows the appropriate sensibility, with detection limits between 0.015 and 0.054 mg L^–1. The proposed method was successfully employed for the determination of organic acids in wine samples by direct sample injection after appropriate dilution and filtration.     

On-line electrolytic dissolution of solid metal samples and determination of copper in aluminium alloys by flame atomic absorption spectrometry

A flow-injection system was developed in which alloy metal samples are electrolytically dissolved and the dissolved samples are analysed by flame atomic absorption spectrometry (FAAS). The effects of electrolyte composition and electrolysis parameters on the dissolution of the sample were studied. The method was used for the determination of copper in aluminium alloys. Electrolyte solutions consisting of 0.2–1.0 M nitric acid are better than other electrolytes tested with regard to both alloy sample dissolution and determination of copper by FAAS. The peak height increases linearly with the electrolysis time or current within a certain range. The detection limit depends on the sensitivity of the detector used, and can be improved by increasing the electrolysis time or current. Generally, aluminium alloys containing 0.5–10% copper can give suitable signals for FAAS determination. The reproducibility of electrolysis and determination is about 4% for the same sampling points and 5% for different sampling points on the alloy sample.     

Optimization of solid-phase extraction procedure for determination of polychlorinated dibenzo-<Emphasis Type="Italic">p</Emphasis>-dioxins,polychlorinated dibenzofurans,and coplanar polychlorinated biphenyls in humic acid containing water

A solid-phase extraction (SPE) method was optimized for accurate determination of polychlorinated dibenzo-p-dioxins (PCDDs), polychlorinated dibenzofurans (PCDFs), and coplanar polychlorinated biphenyls (CoPCBs) in humic acid containing surface water. Recovery experiments using humic materials revealed that humic acids permit dioxins to pass through an octadecylsilica (C₁₈) extraction disk by associating with them under weakly alkaline conditions. Acidification of the sample before percolation improved this otherwise insufficient recovery. The analysis of surface water acidified to pH 2 gave better recovery with surrogate standards and lower quantitative values for higher-chlorinated homologues than the sample at pH 9. In all samples, the native octachlorodibenzo-p-dioxin (OCDD) peak abundance showed no difference between at pH 2 and at pH 9, indicating overestimation of the quantitative value of the homologue at pH 9. Acidification of a humic acid containing water sample can avoid overestimation of higher-chlorinated congeners caused by insufficient recovery of their corresponding surrogates.     

高效毛细管电泳分离测定水中的乙酸和氯代乙酸

用邻苯二甲酸氢钾(pH=5.4)缓冲液作为电泳的背景电解质,以十六烷基三甲基溴化铵作为电渗流抑制剂,用甲基叔丁基醚作为萃取剂处理水样,建立了一种测定水中的乙酸和氯代乙酸的简单灵敏的毛细管区带电泳(紫外检测)法.测定结果表明,分析物的迁移时间和峰面积的日内相对标准偏差分别低于0.33%和4.45%,日间相对标准偏差分别低...     

Optimization of dynamic pH junction for the sensitive determination of amino acids in urine by capillary electrophoresis

A capillary electrophoresis method with UV-absorbance detection was studied and optimized for the determination of underivatized amino acids in urine. To improve concentration sensitivity the utility of in-capillary analyte stacking via dynamic pH junction was investigated with phenylalanine (Phe) and tyrosine (Tyr) as model amino acids. Before sample injection, a plug of ammonium hydroxide solution was injected to enable analyte concentration. Samples were 1:1 (v/v) mixed with background electrolyte (1 M formic acid) prior to injection. The effect of the injected sample volume, and the injected ammonium hydroxide volume and concentration on analyte stacking and separation performance was investigated. The optimal volume of ammonium hydroxide depended on the injected sample volume. Using a dynamic pH junction good resolution (1.4) was obtained for a sample injection volume of 10% of the capillary (196 nl) with Phe and Tyr dissolved in water. Limits of detection (LODs) were 0.036 and 0.049 μM for Phe and Tyr, respectively. For urine samples, the optimized procedure comprised a 1.7-nl injection of 12.5% ammonium hydroxide, followed by a 196-nl injection of urine spiked with Phe and Tyr. Satisfactory resolution was obtained and amino acid peak widths at half height were only 1.6 s indicating efficient stacking. Calibration plots for Phe and Tyr in urine showed good linearity (R(2) > 0.96) in the concentration range 10-175 μM, and LODs for Phe and Tyr were 0.054 and 0.019 μM, respectively. RSDs for peak area and migration time for Phe and Tyr were below 7.5% and 0.75%, respectively.     

Sample matrix influence on the choice of background electrolyte for the analysis of bases with capillary zone electrophoresis

Low levels of impurities need to be determined in drugs. Consequently, if UV detection is used, a large sample amount must be loaded and as narrow peaks as possible obtained. The sample matrix and the stability of the samples as well as the peak resolution should be considered when the electrolyte is chosen. In this study the influence of the sample matrix composition with varying background electrolytes on the peak appearance of model mixtures loaded in large amounts was investigated. A robust electrolyte for analysis of bases in a sample with varying pH was found to consist of a buffering co-ion and a buffering counter-ion (the pH was approximately 4.2 in the electrolyte). If a minor component has higher mobility than the macrocomponent and the co-ion, better peak shape can be obtained if, for instance, enough sodium chloride is added to the sample, i.e., sample self-stacking is exploited. The effect of addition of organic modifiers, isopropanol or acetonitrile, was examined and good linearity and precision have been shown for impurities in the concentration range tested, approximately 0.03 to 5 mol% of the main component, in model mixtures.     

Determination of silicon in high-silicon electrical steel by ICP-AES with on-line sample electrolytic dissolution.

A flow-injection procedure combining electrolytic sample decomposition and inductively coupled plasma atomic emission spectrometry (ICP-AES) is proposed in order to rapidly determine the content of silicon in high-silicon electrical steel. This system is characterized by sample decomposition through electrolysis directly coupled to ICP-AES. A steel sample is dissolved by electrolysis using a 6 mol L(-1) HCl solution as an electrolyte with a flow rate of 5 mL min(-1); the electrolyte containing a dissolved sample is subsequently introduced into ICP-AES via a nebulizer. The effects of the electrolysis current and the temperature on the decomposition of the sample were studied. Samples were electrolyzed under the condition of a 1.5 A constant current, at room temperature (25 degrees C) to avoid the hydrolysis of silicon to precipitate. Comparing the analytical results of steel samples obtained by this analytical system with those obtained by the gravimetric method, determined values agreed well quantitatively. The RSD of silicon at approximately 3% was 0.3% (n = 6).     

Influence of a stacking phenomenon on the results of Hadamard transform capillary electrophoresis

Advantageous features (enhanced sensitivity and low baseline noise) of the multiplex measuring procedure, the Hadamard transform capillary electrophoresis (HT-CE), are experimentally demonstrated and critically discussed. To perform a perfect multiplex experiment in CE, sample species need to be dissolved in the background electrolyte medium and have very low concentration. The mismatch of electric conductivity resulting from a sample dissolved in water or in a separation buffer diluted with water will lead to sample stacking and corrupting the anticipated outcome. The multiplex measurements were carried out with benzyltriethylammonium bromide, resorcinol and 3,5-dihydroxybenzoic acid in the phosphate buffer, 511 sample/buffer injections were performed into the capillary according to the pseudorandom binary sequence. The averaged electropherogram of the single injection was calculated from the detection signal with the aid of the Fourier transform. The results illustrate the detrimental effect of sample matrix dilution with water and the effect of increased initial sample concentration on the multiplex measurement in CE. Multiplex advantage, in theory possible in the HT-CE, can be obtained at low concentration levels feasible with laser induced fluorescence and optically gated sampling. To achieve successful multiplex measurements with the UV detector, the single injection signal should be approximately at the baseline noise level.     

Mass spectrometry in the characterization of ambers. II. Free succinic acid in fossil resins of different origin

Baltic amber contains high levels of succinic acid, most of which is part of the polymer framework, and only recently has the presence of microcrystals of free succinic acid been documented by scanning electron microscopy and X‐ray diffraction analysis. The determination of succinic acid can be used for an easy identification of Baltic amber among other fossil resins and to distinguish it from imitations, widely diffused on the market, produced with natural or modified recent or sub‐fossil resins, such as copals. We report here a simple method, based on negative ion electrospray ionization mass spectrometry, for evaluating the free succinic acid content in water/methanol extracts of ambers from different origin, using a sample of about 20 mg. The limit of quantification is better than 1 ppm and, when applied to a set of amber samples of different origin, it was able to distinguish those of Baltic origin (showing free succinic acid levels in the range 50–400 ppm) from the others (for which succinic acid was undetectable, i.e. at levels lower than 1 ppm). Copyright © 2009 John Wiley & Sons, Ltd.     

Simultaneous capillary electrophoretic separation of small anions and cations after complexation with ethylenediaminetetraacetic acid

A new approach for simultaneous separation of small inorganic and organic anions and metal cations by capillary electrophoresis is demonstrated. Metal cations in the sample are transformed into their chelates with EDTA and are separated together with the anions using an anionic separation mode. Simultaneous separation of 19 common anions and cations was achieved in about 6 min with the electrolyte containing 5 mM K2CrO4, 3 mM boric acid, 35 microM cetyltrimethylammonium bromide and 12 microM EDTA at pH 8. Limits of detection (s/n = 3) were in the range from 4 ppb for Cl- up to 1250 ppb for Cu-EDTA and RSDs of peak areas ranged from 1.4% for Cl- up to 8.5% for Mn-EDTA chelate. The practical applicability of the method was demonstrated on the analysis of anions and cations in various water samples.     

Rapid polarographic method for determination of arsenic in ferrotungsten

A simple and sensitive method for determining arsenic in ferrotungsten is presented. The alloy is dissolved in aqua regia and the arsenic reduced with K(2)S(2)O(5). The polarographic wave is recorded for an electrolyte at pH 3.0 and containing Fe(II), Mn(II), citric acid and ascorbic acid. Levels of 0.2%, and 0.003% As can be determined with errors of +/- 8 and +/- 20% respectively. The limit of detection is 0.003%.     

Proteomics based on selecting and quantifying cysteine containing peptides by covalent chromatography

This paper describes a procedure in which cysteine containing peptides from tryptic digests of complex protein mixtures were selected by covalent chromatography based on thiol-disulfide exchange. identified by mass spectrometry, and quantified by differential isotope labeling. Following disruption of disulfide bridges with 2,2'-dipyridyl disulfide, all proteins were digested with trypsin and acylated with succinic anhydride. Cysteine containing peptides were then selected from the acylated digest by disulfide interchange with sulfhydryl groups on a thiopropyl Sepharose gel. Captured cysteine containing peptides were released from the gel with 25 mM dithiothreitol (pH 7.5) containing 1 mM (ethylenedinitrilo)tetraacetic acid disodium salt and alkylated with iodoacetic acid subsequent to fractionation by reversed-phase liquid chromatography (RPLC). Fractions collected from the RPLC column were analyzed by matrix-assisted laser desorption ionization mass spectrometry. Based on isotope ratios of peptides from experimental and control samples labeled with succinic and deuterated succinic anhydride, respectively, it was possible to determine the relative concentration of each peptide species between the two samples. Peptides obtained from proteins that were up-regulated in the experimental sample were easily identified by an increase of the relative amount of the deuterated peptide. The results of these studies indicate that by selecting cysteine containing peptides, the complexity of protein digest could be reduced and database searches greatly simplified. When coupled with the isotope labeling strategy for quantification it was possible to determine proteins that were up-regulated in plasmid bearing Escherichia coli when expression of plasmid proteins was induced. Up-regulation of several proteins of E. coli origin was also noted.     

Peak distortion in the column liquid chromatographic determination of omeprazole dissolved in borax buffer.

Injection of a sample containing omeprazole dissolved in borax buffer (pH 9.2) into a reversed-phase liquid chromatographic system consisting of a mixture of acetonitrile and phosphate buffer (pH 7.6) as the mobile phase and a C18 surface-modified silica as the solid phase resulted under special conditions in split peaks of omeprazole. The degree of peak split and the retention time of omeprazole varied with the concentration of borax in the sample solution and the ionic strength of the mobile phase buffer as well as with the column used. Borax is eluted from the column in a broad zone starting from the void volume of the column. The retention is probably due to the presence of polyborate ions. The size of the zone varies with the concentration of borax in the sample injected. In the borax zone the pH is increased compared with the pH of the mobile phase, and when omeprazole (a weak acid) is co-eluting in the borax zone its retention is affected. In the front part and in the back part of the borax zone, pH gradients are formed, and these gradients can induce the peak splitting. When the dissolving medium is changed to a phosphate buffer or an ammonium buffer at pH 9 no peak distortion of omeprazole is observed.