Uniform metal nanoparticles produced at high yield in dense microemulsions

This article demonstrates that bicontinuous microemulsions are optimal templates for high yield production of metal nanoparticles. We have verified this for a variety of microemulsion systems having AOT (sodium bis (2-ethyhexyl) sulphosuccinate) or a fluorocarbon (perfluoro (4-methyl-3,6-dioxaoctane)sulphonate) as surfactant mixed with water and oils like n-heptane or n-dodecane. Several types of metal nanoparticles, including platinum, gold and iron, were produced in these microemulsions having a size range spanning 1.8-17 nm with a very narrow size distribution of ±1 nm. Remarkably high mass concentrations up to 3% were reached. Size and concentration of the nanoparticles could be varied with the stoichiometries of the reagents that constituted them. The optimization towards high yield while maintaining low size polydispersity is due to the decoupling of the time scales for the precipitation reaction and for coarsening. In actual fact, coalescence is essentially prevented by the immobilization of nanoparticles within the bicontinuous microemulsion structure.     

Preparation of metal nanoparticles in water-in-oil (w/o) microemulsions

The use of an inorganic phase in water-in-oil microemulsions has received considerable attention for preparing metal particles. This is a new technique, which allows preparation of ultrafine metal particles within the size range 5 nm相似文献   

Noncovalent attachment of oxide nanoparticles onto carbon nanotubes using water-in-oil microemulsions

We report a simple and general noncovalent method for attaching ZnO and MgO nanoparticles onto MWNTs using water-in-oil microemulsions, which is important for preserving the mechanical and electrical properties of carbon nanotubes.     

Formation of silica nanoparticles in microemulsions

Silica nanoparticles for controlled release applications have been produced by the reaction of tetramethylorthosilicate (TMOS) inside the water droplets of a water-in-oil microemulsion, under both acidic (pH 1.05) and basic (pH 10.85) conditions. In-situ FTIR measurements show that the addition of TMOS to the microemulsion results in the formation of silica as TMOS, preferentially located in the oil phase, diffuses into the water droplets. Once in the hydrophilic domain, hydrolysis occurs rapidly as a result of the high local concentration of water. Varying the pH of the water droplets from 1.05 to 10.85, however, considerably slows the hydrolysis reaction of TMOS. The formation of a dense silica network occurs rapidly under basic conditions, with IR indicating the slower formation of more disordered silica in acid. SAXS analysis of the evolving particles shows that approximately 11 nm spheres are formed under basic conditions; these are stabilized by a water/surfactant layer on the particle surface during formation. Under acidic conditions, highly uniform approximately 5 nm spheres are formed, which appear to be retained within the water droplets (approximately 6 nm diameter) and form an ordered micelle nanoparticle structure that exhibits sufficient longer-range order to generate a peak in the scattering at q approximately equal to 0.05 A-1. Nitrogen adsorption analysis reveals that high surface area (510 m2/g) particles with an average pore size of 1 nm are formed at pH 1.05. In contrast, base synthesis results in low surface area particles with negligible internal porosity.     

微乳液法制备纳米粒子

介绍了W／O型微乳液内超细颗粒的形成机理、制备的技术关键，综述了近年来国内外微乳法制备纳米粒子的最新进展。引用文献37篇。     

Polymer-induced recovery of nanoparticles from microemulsions

A new isothermal approach to the recovery of inorganic nanoparticles (NPs) is demonstrated. The NPs can be incorporated into a background microemulsion (ME) supporting fluid, and they can be recovered by addition of non-adsorbing polymer. A clean liquid-liquid (L-L) phase transition can be readily induced by addition of polymer to the MEs. Furthermore, the L-L transitions are also observed in the presence of added NPs, but now the nanoparticles concentrate in the lower co-existing ME phases. Once recovered, the NPs can be redispersed by adding extra ME as a solvent.     

Magnesium hydroxide nanoparticles synthesized in water-in-oil microemulsions

Well-dispersed magnesium hydroxide nanoplatelets were synthesized by a simple water-in-oil (w/o) microemulsion process, blowing gaseous ammonia (NH(3)) into microemulsion zones solubilized by magnesium chloride solution (MgCl(2)). Typical quaternary microemulsions of Triton X-100/cyclohexane/n-hexanol/water were used as space-confining microreactors for the nucleation, growth, and crystallization of magnesium hydroxide nanoparticles. The obtained magnesium hydroxide was characterized by field-emission scanning electron microscopy (FESEM), high-resolution transmission election microscopy (HRTEM), X-ray powder diffraction (XRD), laser light scattering, Fourier transform infrared spectroscopy (FT-IR), and thermogravimetric analysis-differential scanning calorimetry (TGA-DSC). The mole ratio of water to surfactant (omega(0)) played an important role in the sizes of micelles and nanoparticles, increasing with the increase of omega(0). The compatibility and dispersibility of nanoparticles obtained from reverse micelles were improved in the organic phase.     

Magnetic properties of binary mixtures of metal oxide nanoparticles

The magnetic properties of mixtures of nanoparticles with similar size distributions but distinct superparamagnetic characteristics were investigated by SQUID magnetometry. Metal oxide nanoparticles were synthesized by the thermal decomposition of metal acetylacetonates. The nanoparticles were characterized by transmission electron microscopy, ⁵⁷Fe Mössbauer spectroscopy, and SQUID magnetometry. Cobalt ferrite and maghemite nanoparticles with average sizes of 5.1 and 5.0 nm were obtained. Zero field cooled magnetization measurements indicate that the nanoparticles are superparamagnetic, with blocking temperatures of 150 and 22 K, respectively. The zero field cooled measurements for mixtures of the nanoparticles behaved as the sum of the respective superparamagnetic behaviours of the two individual components. This suggests the energy barrier to spin fluctuation is insensitive to the presence of nanoparticles with distinct superparamagnetic characteristics. However, the magnetization versus field measurements provide evidence for interparticle interactions, even at room temperature.     

Zirconium phosphate nanoparticles from water-in-oil microemulsions

Non-ionic water-in-oil (w/o) microemulsions of pentaoxyethylenenonylphenyl ether (Igepal-CO520)/cyclohexane/water at 25 °C have been used as reaction vessels to obtain zirconium hydrogen phosphate nanoparticles.     

Growth of silica nanoparticles in methylmethacrylate-based water-in-oil microemulsions

The mechanism of silica particle formation in monomer microemulsions is studied using dynamic light scattering (DLS), atomic force microscopy, small-angle X-ray scattering (SAXS), and conductivity measurements. The hydrolysis of tetraethylorthosilicate (TEOS) in methylmethacrylate (MMA) microemulsions (MMA = methylmethacrylate) is compared with the formation of SiO₂ particles in heptane microemulsions. Stable microemulsions without cosurfactant were found for MMA, the nonionic surfactant Marlophen NP10, and aqueous ammonia (0.75 wt%). In the one-phase region of the ternary phase diagram, the water/surfactant ratio (R _w) could be varied from 6 to 18. The DLS and SAXS measurements show that reverse micelles form in these water-in-oil (w/o) microemulsions. The minimum water-to-surfactant molar ratio required for micelle formation was determined. Particle formation is achieved from the base-catalyzed hydrolysis of TEOS. According to atomic force microscopy measurements of particles isolated from the emulsion, the particle size can be effectively tailored in between 20 and 60 nm by varying R _w from 2–6 in heptane w/o microemulsions. For MMA-based microemulsions, the particle diameter ranges from 25 to 50 nm, but the polydispersity is higher. Tailoring of the particle size is not achieved with R _w, but adjusting the particle growth period produces particles between 10 and 70 nm.     

Characterization of iron hydroxide/oxide nanoparticles prepared in microemulsions stabilized with cationic/non-ionic surfactant mixtures

Iron oxide-hydroxide (α-Fe(2)O(3); Fe(OH)(3)) nanoparticles have been prepared by a microemulsion route using ammonia (NH(3)) solution or tetrabutylammonium hydroxide (TBAH) as precipitants. The iron oxide-hydroxide nanoparticles obtained were characterized by TGA, N(2) sorptiometry, XRD, IR, SEM, HR-TEM, and DLS techniques. Properties such as specific surface area (S(BET)), pore sizes and shapes, average particle size and distribution, crystallite structure, and thermal stability were determined. The properties of nanoparticles prepared using NH(3) and TBAH were compared after drying at 100°C and after being calcined in the temperature range 250-1100°C. It was found that the suspensions prepared using TBAH suffered immediate separation while those prepared using NH(3) resulted in very stable suspensions. Also, it was found that TBAH did not offer any advantage over NH(3) either in terms of specific surface area or in particle size of the prepared nanoparticles. Hence, the later part of the study was concentrated on the NH(3)-precipitated nanoparticles with particular emphasis on finding the most favorable, W (water-to-surfactant ratio) and/or surfactant concentration, S, to obtain the best conditions in terms of higher surface areas and narrower particle size distribution. It was found that the prepared suspension consisted of monodisperse nanoparticles (standard deviations <10%) and after separation and drying, high surface area powders were obtained. The highest surface area (315 m(2) g(-1)) was obtained when the smallest W (=20) and highest S (=0.20 mol L(-1)) were employed.     

Organic reaction pathways in the nonaqueous synthesis of metal oxide nanoparticles

Nonaqueous-solution routes to metal oxide nanoparticles are a valuable alternative to the known aqueous sol-gel processes, offering advantages such as high crystallinity at low temperatures, robust synthesis parameters and ability to control the crystal growth without the use of surfactants. In the first part of the review we give a detailed overview of the various solution routes to metal oxides in organic solvents, with a strong focus on surfactant-free processes. In most of these synthesis approaches, the organic solvent plays the role of the reactant that provides the oxygen for the metal oxide, controls the crystal growth, influences particle shape, and, in some cases, also determines the assembly behavior. We have a closer look at the following reaction systems in this order: 1) metal halides in alcohols, 2) metal alkoxides, acetates, and acetylacetonates in alcohols, 3) metal alkoxides in ketones, and 4) metal acetylacetonates in benzylamine. All these systems offer some peculiarities with respect to each other, providing many possibilities to control and tailor the particle size and shape, as well as the surface and assembly properties. In the second part we present general mechanistic principles for aqueous and nonaqueous sol-gel processes, followed by the discussion of reaction pathways relevant for nanoparticle formation in organic solvents. Depending on the system several mechanisms have been postulated: 1) alkyl halide elimination, 2) elimination of organic ethers, 3) ester elimination, 4) C--C bond formation between benzylic alcohols and alkoxides, 5) ketimine and aldol-like condensation reactions, 6) oxidation of metal nanoparticles, and 7) thermal decomposition methods.     

Pyrene-terminated phenylenethynylene rigid linkers anchored to metal oxide nanoparticles

Phenylenethynylene (PE) rigid linkers (para and meta) were used to anchor pyrene to the surface of TiO2 (anatase) and ZrO2 nanoparticle thin films through the two COOH groups of an isophthalic acid (Ipa) unit. Four chromophore-linker models were studied in solution and bound. Two are novel meta-pyrene-PE linker systems: dimethyl 5-(3-(1-pyrenylethynyl)phenylethynyl)-isophthalate, carrying one pyrene, and dimethyl 5-(bis-3,5-(1-pyrenylethynyl)phenylethynyl)-isophthalate, carrying two. These were compared with para rigid-rods dimethyl 5-(1-pyrenylethynyl)isophthalate and dimethyl 5-(4-(1-pyrenylethynyl)phenylethynyl)-isophthalate, each carrying one pyrene but varying in length. The length of the PE linkers and the para or meta substitution influence the photophysical properties of the compounds. The extinction coefficient increased, and the long wavelength absorbance of the pyrene chromophore was shifted to the red with increasing conjugation. Compared to unsubstituted pyrene, the pyrene-linker systems were characterized by short fluorescence lifetimes (tau approximately 2 ns in tetrahydrofuran solutions), but quantum yields were close to unity. ZINDO/S CI calculations attribute this effect to a switching in the order of the two lowest-lying singlet states of pyrene. High surface coverages, approximately 10(-8) mol/cm2, and carboxylate binding modes on nanostructured TiO2 films were obtained in all cases. The appearance of a pyrene excimer emission on ZrO2, an insulator, indicates that the pyrene-linker system is closely packed (Py-Py < 4 A) on the surface. The fluorescence emission on TiO2 was completely quenched, consistent with quantitative and rapid electron injection into the semiconductor indicating that the pyrene excimer acts as a sensitizer. Photoelectrochemical studies in regenerative solar cells with I3-/I- as the redox mediator indicated near-quantitative conversion of absorbed photons into an electrical current.     

One-minute synthesis of crystalline binary and ternary metal oxide nanoparticles

Highly crystalline metal oxide nanoparticles such as CoO, ZnO, Fe(3)O(4), MnO, Mn(3)O(4), and BaTiO(3) were synthesized in just a few minutes by reacting metal alkoxides, acetates or acetylacetonates with benzyl alcohol under microwave heating.     

Formation of TiO2 nanoparticles in water-in-CO2 microemulsions

Titanium dioxide nanoparticles can be produced by the controlled hydrolysis of titanium tetraisopropoxide in water-in-CO2 (w/c) microemulsions stabilized with the surfactants ammonium carboxylate perfluoropolyether (PFPE-NH4) and poly(dimethyl amino ethyl methacrylate-block-1H,1H,2H,2H-perfluorooctyl methacrylate) (PDMAEMA-b-PFOMA); the greater control of hydrolysis and particle growth with PDMAEMA-b-PFOMA is consistent with the differences in the stabilities and interactions for these two microemulsions.     

Enzymatic biosensors based on the use of metal oxide nanoparticles

Over the past decades, various techniques have been developed to obtain materials at a nanoscale level to design biosensors with high sensitivity, selectivity and efficiency. Metal oxide nanoparticles (MONPs) are of particular interests and have received much attention because of their unique physical, chemical and catalytic properties. This review summarizes the progress made in enzymatic biosensors based on the use of MONPs. Synthetic methods, strategies for immobilization, and the functions of MONPs in enzymatic biosensing systems are reviewed and discussed. The article is subdivided into sections on enzymatic biosensors based on (a) zinc oxide nanoparticles, (b) titanium oxide nanoparticles, (c) iron oxide nanoparticles, and (d) other metal oxide nanoparticles. While substantial advances have been made in MONPs-based enzymatic biosensors, their applications to real samples still lie ahead because issues such as reproducibility and sensor stability have to be solved. The article contains 256 references.

石墨烯负载的金属氧化物纳米颗粒的可控制备及催化性能

采用直接浸渍法、过氧化氢均相氧化沉积法和氨水催化水解法制备了石墨烯负载的铁、钴、镍金属氧化物纳米颗粒.研究了三种沉积方法对颗粒尺寸分布的影响;采用透射电子显微镜、傅里叶变换红外光谱、X射线衍射和X射线光电子能谱表征了催化剂的形貌与结构.用过氧化氢均相氧化沉淀法可制得粒径分布最均匀的纳米颗粒.过氧化氢的氧化作用可使石墨烯表面的氧化基团含量最大化,为纳米颗粒提供了足够的吸附与成核点.氨水加速了金属离子的水解与成核,导致纳米颗粒的粒径增大与不均.以苯甲醇氧化为探针反应考察了催化剂的性能.催化剂的活性按以下顺序逐渐下降:过氧化氢辅助沉积法>直接浸渍法>氨水催化水解法,与纳米颗粒尺寸增长趋势一致.纳米催化剂颗粒尺寸与其活性的良好关联性显示,发展石墨烯负载尺寸可控的纳米催化剂的方法具有重要意义.     

Structural properties of palladium nanoparticles embedded in inverse microemulsions

Pd nanoparticles were synthesized by reduction of palladium acetate by ethanol in systems containing tetrahydrofuran (THF) as dispersion medium and tetradodecylammonium bromide (TDABr) surfactant as stabilizer. The polar phase (ethanol) acts at the same time as reducing agent. THF/TDABr/H₂O inverse microemulsions containing micelles of various sizes were also prepared, and the structure of complex liquids was studied by density measurements. Sols containing nanosize Pd⁰ particles were synthesized within the water droplets of this micellar system. The stabilized Pd⁰/surfactant system was characterized by density measurements, absorption spectroscopy, and transmission electron microscopy. The stabilizing surfactant layer adsorbed on the liquid/liquid interface and on the surface of the nanoparticles (i.e., the liquid/solid interface) significantly reduced the excess volume for the palladium nanodispersion in organic solvent. Received: 17 July 2000 Accepted: 5 October 2000