Phase separation of gas–liquid and liquid–liquid microflows in microchips

Phase separation of gas–liquid and liquid–liquid microflows in microchannels were examined and characterized by interfacial pressure balance. We considered the conditions of the phase separation, where the phase separation requires a single phase flow in each output of the microchannel. As the interfacial pressure, we considered the pressure difference between the two phases due to pressure loss in each phase and the Laplace pressure generated by the interfacial tension at the interface between the separated phases. When the pressure difference between the two phases is balanced by the Laplace pressure, the contact line between the two phases is static. Since the contact angle characterizing the Laplace pressure is restricted to values between the advancing and receding contact angles, the Laplace pressure has a limit. When the pressure difference between the two phases exceeds the limiting Laplace pressure, one of the phases leaks into the output channel of the other phase, and the phase separation fails. In order to experimentally verify this physical picture, microchips were used having a width of 215 μm and a depth of 34 μm for the liquid–liquid microflows, a width of 100 μm and a depth of 45 μm for the gas–liquid microflows. The experimental results of the liquid–liquid microflows agreed well with the model whilst that of the gas–liquid microflows did not agree with the model because of the compressive properties of the gas phase and evaporation of the liquid phase. The model is useful for general liquid–liquid microflows in continuous flow chemical processing.     

Determination of pesticide residues in red wines with microporous membrane liquid–liquid extraction and gas chromatography

A sample pretreatment method based on microporous membrane liquid-liquid extraction (MMLLE) was developed for the subsequent gas chromatographic determination of pesticides in wine. MMLLE provided efficient and selective extraction with enrichment factors in the range 3-13. The gas chromatographic separation was carried out using on-column injection and flame ionization detection. The method was linear, repeatable and sensitive. The limits of quantification were better than 0.006 mg/L for all the analytes except for iprodione (0.37 mg/L). The method was applied to the determination of pesticides in several red wines of different origin.     

Mathematical modeling of gas separation permeators — for radial crossflow,countercurrent, and cocurrent hollow fiber membrane modules

A new approach to solve the mass transfer problem posed by the permeation process in a hollow fiber permeator is presented and analyzed. The algorithm models the separation offered for a membrane module, for given gas conditions, simulating the permeate and residue composition and the stage cut. The advantage of the ‘succession of states’ approach utilized here is the option of retroactive incorporation of more complex interactions such as permeate pressure buildup, a pressure, composition and temperature dependent permeability. The two dimensional mass transfer in a radial crossflow permeator has been qualitatively discussed in the past, but it has not been modeled in the literature. The countercurrent, cocurrent and crossflow configurations (all single dimensional mass transfer cases) for gas separation have been modeled in literature primarily by numerical integration of the differential equations over the relevant boundary conditions. Incorporation of nonlinearities such as pressure and permeability variations complicate the mathematics considerably for a single dimension, and make their solution almost impossible in two dimensions. This paper proposes an algorithm that simplifies the understanding of the problem posed, in terms of practical parameters (such as stage cut), and analyses the three flow patterns (radial crossflow, countercurrent, and cocurrent) in detail.     

On-line coupling of microporous membrane liquid–liquid extraction and gas chromatography in the analysis of organic pollutants in water

A method for the determination of hydrophobic pollutants in surface waters was developed. The pretreatment was done with microporous membrane liquid–liquid extraction, the extract was eluted to a sample loop in the large-volume injector valve of the gas chromatograph and the extract was injected on-line to the gas chromatograph. The method was optimised using standard compounds and the linearity, the limits of detection and quantification of the method were studied. The method allowed the determination of hydrophobic pesticides and PAHs at the ng L^–1 level. The RSD values for the repeatability of the method varied from 4.2% to 25.6%, being on average 9.5%. Surface water samples from Finnish lakes and rivers were analysed.     

Kinetic characteristics of gas–liquid ozone reactions

An experimental chemical method for determining the kinetic characteristics (volumetric mass transfer coefficient and rate constant of a second-order reaction) of gas–liquid ozone reactions in a bubble column reactor is described. The calculation formulas are substantiated, and the ranges of values of the experimental factors that determine the method’s limits of applicability are found. The conditions under which the boundary-value problem of a gas–liquid ozone reaction of the second order can be reduced to a problem of a pseudo-first order reaction allowing an analytical solution are revealed.     

Analysis of PAH compounds in soil with on-line coupled pressurised hot water extraction–microporous membrane liquid–liquid extraction–gas chromatography

Pressurised hot water extraction (PHWE) was coupled on-line with microporous membrane liquid-liquid extraction (MMLLE) and gas chromatography (GC) in the analysis of polycyclic aromatic hydrocarbon (PAH) compounds in soil. The MMLLE serves as a trapping device after the PHWE. Water from PHWE is directed to the donor side of the membrane unit and the analytes are extracted to the acceptor solution on the other side of the membrane. The role of MMLLE is to clean and concentrate the extract, which is then transferred on-line to the GC via a sample loop and an on-column interface using partially concurrent solvent evaporation. Separate optimisation of MMLLE and simulations of the PHWE-MMLLE connection were carried out before the actual on-line coupling. After optimisation of the whole on-line system, the efficiencies of the PHWE-MMLLE-GC and PHWE-solid-phase trap extractions were compared. The PHWE-MMLLE-GC method allowed on-line analysis of soil samples. The method was linear, with limits of detection in the range 0.05-0.13 ng and limits of quantification 0.65-1.66 microg g(-1). Comparison of the results with those obtained by other techniques confirmed the good performance.     

The sloshing effects on distribution characteristics of gas–liquid mixture in spiral-wound heat exchanger

Journal of Thermal Analysis and Calorimetry - Spiral-wound heat exchanger (SWHE) is important equipment for industry, and it is suitable for floating production storage off-loading (FPSO). However,...     

Determination of organochlorine pesticides in river water using dispersive liquid–liquid microextraction and gas chromatography–electron capture detection

Dispersive liquid–liquid microextraction (DLLME) coupled with gas chromatography–electron capture detection (GC–ECD), has been developed for the extraction and determination of 14 organochlorine pesticides (hexachlorocyclohexanes (α-HCH, β-HCH and δ-HCH), Lindane (γ-HCH), Aldrin, Dieldrin, Endrin, Heptachlor, Heptachlor epoxide, α-Chlordane, β-Chlordane and p,p′-DDT, p,p′-DDD, p,p′-DDE) in river water samples. Factors relevant to the microextraction efficiency, such as the kind of extraction and disperser solvent, their volume and the salt effect was investigated and optimised. In this method the appropriate mixture of extraction solvent (13.5 µL carbon disulphide) and disperser solvent (0.50 mL acetone) were rapidly injected into the aqueous sample by syringe. The values of the detection limit of the method were in the range of 0.05–0.001 µg L^?1, while the relative standard deviations for five replicates varied from 2.7 to 9.3%. A good linearity (0.9894 ≤ r ² ≤ 0.9998) and a broad linear range (0.01–200 µg L^?1) were obtained. The method exhibited enrichment factors ranging from 647 to 923, at room temperature. The relative standard deviations varied from 2.7 to 9.3% (n = 5). The relative recoveries of each pesticide from water samples at spiking levels of 2.00 and 10.0 µg L^?1 were 88.0–111.0% and 95.8–104.1%, respectively. Finally, the proposed method was successfully utilised for the preconcentration and determination of the organochlorine pesticides in the Jajrood River water samples.     

The design of membrane vapor–gas separation systems

Membrane vapor–gas separation systems are beginning to be applied to a number of gas separation problems in the petrochemical and refinery areas. In this paper, some of the factors that affect the design of these systems are described using, as an application example, the separation of propylene from nitrogen in polyolefin resin degassing vents.     

Determination of non-steroidal anti-inflammatory drugs in urine by the combination of stir membrane liquid–liquid–liquid microextraction and liquid chromatography

A stir membrane liquid phase microextraction procedure working under the three-phase mode is proposed for the first time for the determination of six anti-inflammatory drugs in human urine. The target compounds are isolated and preconcentrated using a special device that integrates the extractant and the stirring element. An alkaline aqueous solution is used as extractant phase while 1-octanol is selected as supported liquid membrane solvent. After the extraction, all the analytes are determined by liquid chromatography (LC) with ultraviolet detection (UV). The analytical method is optimized considering the main involved variables (e.g., pH of donor and acceptor phases, extraction time, stirring rate) and the results indicate that the determination of anti-inflammatory drugs at therapeutic and toxic levels is completely feasible. The limits of detection are in the range from 12.6 (indomethacin) to 30.7 μg/L (naproxen). The repeatability of the method, expressed as relative standard deviation (RSD, n = 5) varies between 3.4% (flurbiprofen) and 5.7% (ketoprofen), while the enrichment factors are in the range from 35.0 (naproxen) to 72.5 (indomethacin).     

Solid–liquid–gas equilibrium of the naphthalene–biphenyl–CO2 system: Measurement and modeling

The first and last melting points (FLMP) method was employed to measure the melting temperature–composition (T–w$T–w$) data at solid–liquid–gas (SLG) equilibrium for the naphthalene–biphenyl–CO₂ system. Results show that the system's phase diagram is simple eutectic under all investigated pressures (0.1, 3.0, 6.0 and 8.0 MPa), and the system's eutectic composition is almost constant. The (T–w$T–w$) data measured with a high-pressure differential scanning calorimetry are in good agreement with these from FLMP. The semi-predictive model using solubility data (SMS) and the calculation model combining with G^E models (CMG) for binary systems were extended to this ternary system. For the SMS model, the Peng–Robinson equation of state (PR-EoS) with the van der Waals one-fluid mixing rule was used to correlate the solubility data of the two solutes in CO₂ to obtain the two interaction parameters k₁₂ and k₁₃ and calculate the fugacity coefficients of the solutes in the liquid and vapor phases; the UNIFAC method was also applied to the activity coefficient of the solutes in the liquid phase. For the CMG model, the PR-EoS combining respectively the MHV1, LCVM, and modified LCVM (mLCVM) mixing rules was applied to the fugacity coefficients of the solutes. Results show that the CMG model with MHV1 gives the best prediction of the system's SLG equilibrium, while the SMS model and the CMG model with mLCVM provide comparable and acceptable results.     

Characterization of collagen fibers in Bruch’s membrane using chemical force microscopy

Bruch’s membrane is a layer composed of collagen fibers located just beneath the retina. This study validates a strategy used to map the morphological and adhesion characteristics of collagen fibers in Bruch’s membrane. Atomic force microscopy tips were functionalized with different chemical groups and used to map the hydrophilic and hydrophobic regions on the surface of the eye tissue. The largest adhesion forces were observed when tips functionalized with NH₂ groups were used. The trend in the adhesion forces was rationalized based on the distribution of different functional groups in the triple-helical structure of the collagen fibers. The results of this study can be used to design more effective strategies to treat eye diseases such as age-related macular degeneration.     

Fast analysis of multiple pesticide residues in apple juice using dispersive liquid–liquid microextraction and multidimensional gas chromatography–mass spectrometry

A method for the rapid trace analysis of 24 residual pesticides in apple juice by multidimensional gas chromatography–mass spectrometry (MD-GC/MS) using dispersive liquid–liquid microextraction (DLLME) was developed and optimized. Several parameters of the extraction procedure such as type and volume of extraction solvent, type and volume of dispersive solvent and salt addition were evaluated to achieve the highest yield and to attain the lowest detection limits. The DLLME procedure optimized consists in the formation of a cloudy solution promoted by the fast addition to the sample (5 ml) of a mixture of carbon tetrachloride (extraction solvent, 100 μl) and acetone (dispersive solvent, 400 μl). The tiny droplets formed and dispersed among the aqueous sample solution are further joined and sedimented (85 μl) in the bottom of the conical test tube by centrifugation. Once extracted, all the 24 pesticides were directly injected and separated by a dual GC column system, comprising a short wide-bore DB-5 capillary column with low film thickness connected by a Deans switch system to a second chromatographic narrower column, with identical stationary phase. The instrumental setting used, in combination with carefully optimized operational fast GC and MS parameters, markedly decreased the retention times of the targeted analytes. The total chromatographic run was 8 min. Mean recoveries for apple juice spiked at three concentrations ranged from 60% to 105% and the intra-repeatability ranged from 1% to 21%. The limits of detection of the 24 pesticides ranged from 0.06 to 2.20 μg/L. In 2 of a total of 28 analysed samples were found residues of captan, although at levels below the maximum limit legal established.     

Elucidation of n-butyl benzyl phthalate biodegradation using high-performance liquid chromatography and gas chromatography–mass spectrometry

n-Butyl benzyl phthalate (BBP) is an endocrine-disrupting chemical. A bacterium species capable of using BBP as the sole source of carbon and energy was isolated from mangrove sediment. Effects of BBP concentration, pH, temperature, and salinity on BBP biodegradation were studied. The optimum pH, temperature, and salinity for the BBP biodegradation were 7.0, 37°C, and 15 g L⁻¹, respectively. BBP was completely degraded within 6 days under optimum conditions, and the biodegradation of BBP could be fitted to a first-order kinetic model. The major metabolites of BBP biodegradation were identified as mono-butyl phthalate, mono-benzyl phthalate, phthalic acid, and benzoic acid by using high-performance liquid chromatography and gas chromatography–mass spectrometry. A preliminary metabolic pathway was proposed for the biodegradation of BBP.      

Determination of atranol and chloroatranol in perfumes using simultaneous derivatization and dispersive liquid–liquid microextraction followed by gas chromatography–mass spectrometry

A new analytical method based on simultaneous derivatization and dispersive liquid–liquid microextraction (DLLME) followed by gas chromatography–mass spectrometry (GC–MS), for the determination of the allergenic compounds atranol and chloroatranol in perfumes, is presented. Derivatization of the target analytes by means of acetylation with anhydride acetic in carbonate buffer was carried out. Thereby volatility and detectability were increased for improved GC–MS sensitivity. In addition, extractability by DLLME was also enhanced due to a less polar character of the solutes. A liquid–liquid extraction was performed before DLLME to clean up the sample and to obtain an aqueous sample solution, free of the low polar matrix from the essential oils, as donor phase. Different parameters, such as the nature and volume of both the extraction and disperser solvents, the ionic strength of the aqueous donor phase or the effect of the derivatization reagent volume, were optimized. Under the selected conditions (injection of a mixture of 750 μL of acetone as disperser solvent, 100 μL of chloroform as extraction solvent and 100 μL of anhydride acetic as derivatization reagent) the figures of merit of the proposed method were evaluated. Limits of detection in the low ng mL⁻¹ range were obtained. Matrix effect was observed in real perfume samples and thus, standard addition calibration is recommended.     

Adsorption of cationic multicharged surfactants at liquid–gas interface

We present the review of the existing methods for describing adsorption at fluid interfaces that may be applicable for multiple charge cationic surfactant structures of various architectures—multiheaded (e.g., dicephalic) structures and multimeric surfactants (e.g., dimeric (so-called gemini), trimeric, tetrameric, etc.). We discuss the role of the prefactor the in the Gibbs adsorption equation originating from the number of charges present in the adsorbed layer and the reasons for the deviation from its thermodynamic value. We present several models of adsorption that can be used to describe surface tension isotherms and appreciate the role of prof. Peter Kralchevski in their development. Application of molecular dynamics methods combined with the approach based on the thermodynamic models of multicharged surfactant adsorption may lead to an explanation of some experimentally observed phenomena and can provide the basis for the development of novel materials designated for a variety of applications.     

Extraction of pesticides in water samples using vortex-assisted liquid–liquid microextraction

A simple solvent microextraction method termed vortex-assisted liquid–liquid microextraction (VALLME) coupled with gas chromatography micro electron-capture detector (GC-μECD) has been developed and used for the pesticide residue analysis in water samples. In the VALLME method, aliquots of 30 μL toluene used as extraction solvent were directly injected into a 25 mL volumetric flask containing the water sample. The extraction solvent was dispersed into the water phase under vigorously shaking with the vortex. The parameters affecting the extraction efficiency of the proposed VALLME such as extraction solvent, vortex time, volumes of extraction solvent and salt addition were investigated. Under the optimum condition, enrichment factors (EFs) in a range of 835–1115 and limits of detection below 0.010 μg L⁻¹ were obtained for the determination of target pesticides in water. The calculated calibration curves provide high levels of linearity yielding correlation coefficients (r²) greater than 0.9958 with the concentration level ranged from 0.05 to 2.5 μg L⁻¹. Finally, the proposed method has been successfully applied to the determination of pesticides from real water samples and acceptable recoveries over the range of 72–106.3% were obtained.     

Rapid determination of ultra-trace amounts of acrylamide contaminant in water samples using dispersive liquid–liquid microextraction coupled to gas chromatography-electron capture detector

The objective of the present study was to develop and validate a rapid, highly sensitive, and reliable extraction method to determine acrylamide in water samples. The method was based on the derivatisation of the acrylamide in the presence of KBr, HBr and saturated Br₂ solution into 2,3-dibromopropionamide and dispersive liquid–liquid microextraction (DLLME) followed by gas chromatography–electron capture detection (GC–ECD) of the analyte. Different parameters that affect the DLLME process such as types and volumes of disperser solvent, ionic strength of aqueous solution and extraction time were investigated and optimised. Under optimal conditions, excellent linearity was obtained between concentration of acrylamide and the response of ECD with correlation of determination (R²) of 0.9999. The precision of the method, which was determined by calculating the relative standard deviations (RSD) of the at least three replicate measurements, was 3.6%. The method presented in this study is sensitive enough for the determination of acrylamide in different water samples with the limit of detection (LOD) value of 1?ng?L^?1. The mean percentage recoveries exceeded 91% for all of spiking levels in the real water samples. The results obtained from DLLME method are validated by EPA method 8032A.