Solubilization and Separation of Dicarboxylic Acids by Surfactant Micelles and Polyelectrolytes

Semi‐equilibrium dialysis (SED) and micellar enhanced ultra filtration (MEUF) methods are used to determine the extent of solubilization of water‐insoluble compounds by surfactant and polyelectrolyte. In this study, solubilization of ortho‐, meta‐ and para‐phthalic acids (OPA, MPA and TPA), 1,4‐ and 2,6‐naphthalene dicarboxylic acids (1,4‐NDCA and 2,6‐NDCA) into hexadecylpyridinium chloride (CPC), and the behavior of these acids to bind to the polyelectrolyte ionizable groups were investigated at 25 °C, using SED and MEUF methods. Polydimethyldiallylammonium chloride (PDMDAAC) is used in this study. It was found that the solubilization of organic acids decreases with increasing the solute mole fractions in micelles. Also, the best separation occurs at the lowest concentration of the phthalate ions and high concentrations of either CPC or PDMDAAC. The results support the idea of charge interaction between the anionic dicarboxylate groups and cationic surfactant or polyelectrolyte. The results also show that the presence of a second phenyl ring does not greatly affect the solubilization behavior of the acids.     

Removal of cadmium ions using micellar-enhanced ultrafiltration with mixed anionic-nonionic surfactants

Micellar-enhanced ultrafiltration (MEUF) was used to remove cadmium ions from wastewater efficiently. In this study the nonionic surfactants polyoxyethyleneglycol dodecyl ether (Brij35) and polyoxyethylene octyl phenyl ether (TritonX-100) were for micellar-enhanced ultrafiltration to lower the dosage of the anionic surfactant sodium dodecyl sulfate (SDS). The surfactant critical micelle concentration (CMC) and the degree of micelle counterion binding were investigated. The effects of nonionic surfactant addition on the efficiency of cadmium removal, the residual quantities of surfactant, the permeate flux and the secondary membrane resistance were investigated. A comparison between MEUF with SDS and MEUF with mixed anionic–nonionic surfactants was undertaken. The results show that the addition of Brij35 or TritonX-100 reduced the CMC of SDS and the degree of counterion binding for the micelles. Due to these variations the Cd²⁺ rejection efficiency was at a maximum when the Brij35:SDS and the TritonX-100:SDS molar ratio was 0.5. The Cd²⁺ rejection efficiency in MEUF with SDS is higher than for MEUF with mixed surfactants when the total dose of surfactant is constant. The permeate flux of MEUF with SDS is higher than that for MEUF with mixed surfactants while the secondary resistance of MEUF with SDS is less than that of MEUF with mixed surfactants.     

Versatility of an intramolecularly hydrogen-bonded 4-(N,N-dimethylamino)benzoate group as a signaling subunit for anion recognition

The versatility of the 4-(N,N-dimethylamino)benzoate (DMAB) group embedded in host 1 as a signaling subunit for anion recognition was elucidated in terms of ¹H NMR, CD, and fluorescence studies. Host 1 showed 1:1 complexation with monovalent anions and stepwise 1:1 and 2:1 (host 1: anion) complexation with divalent phosphate anions. The binding constants between host 1 and anions were determined by means of ¹H NMR titrations in CD₃CN (HPO₄²⁻: log K_1:1=6.2, log K_2:1=4.9; H₂P₂O₇²⁻: log K_1:1=4.4, log K_2:1=1.8; AMP²⁻: log K_1:1>7, log K_2:1>5) and the affinity of host 1 toward divalent anions, HPO₄²⁻, H₂P₂O₇²⁻, and AMP²⁻, is stronger than that toward monovalent anions, NO₃⁻, BF₄⁻, ClO₄⁻, HSO₄⁻, and PF₆⁻. The CD exciton chirality studies of host 1 with divalent anions, HPO₄²⁻ and AMP²⁻, revealed that the two DMAB groups in the 2:1 complexes were arranged with negative chirality (counterclockwise). The dual fluorescence behavior of the DMAB group demonstrated not only the complexation stoichiometry but also the role(s) of the lipophilic countercation such as tetrabutylammonium and/or the hydrophilic residue in AMP during anion recognition.     

Mesoporous aluminosilicate ropes with improved stability from protozeolitic nanoclusters

Mesoporous aluminosilicate ropes with improved hydrothermal stability have been prepared through S⁺X⁻I⁺ route via self-assembly of protozeolitic nanoclusters with cetyltrimethylammonium bromides (CTAB) template micelles in HNO₃ solution. SEM observation confirmed that high-yield aluminosilicate ropes could be produced under proper HNO₃ concentration. NO₃⁻ ions had strong binding strength to the CTA⁺ ions and tended to form more elongated surfactant micelles, thus fibrous products were fabricated under the direction of these long rod micelles in shearing flow. At the same time, the NO₃⁻ ions combining with CTA⁺ ions generated more active (CTA⁺NO₃⁻) assembly, which effectively catalysed the polymerization of protozeolitic nanoclusters with large volume into highly ordered mesostructures. Compared with normal MCM-41 silica synthesized through S⁺X⁻I⁺ route in acidic media, the hydrothermal stability was improved considerably. These protozeolitic nanoclusters survived strongly acidic media and entered into mesostructured framework, which contributed to the improvement of hydrothermal stability.     

Effect of counterion condensation on the acid-base equilibrium of a pH-sensitive merocyanine dye covalently attached to polyelectrolytes

Effects of monovalent and divalent counterions on the acid-base equilibrium of a pH-sensitive merocyanine dye covalently attached to copolymers of acrylic acid and acrylamide with varying charge densities (0.28 < ξ < 2.8) were investigated. Added chloride salts of Li⁺, Na⁺, K⁺, and NH⁺₄ (< 0.2 mM) had essentially no effect on pK observed (pK^obs) for the equilibrium. By contrast, the salts of Mg²⁺, Ca²⁺, Sr²⁺, and Ba²⁺ caused a significant decrease in pK^obs for the copolymers with larger ξ. With smaller ξ, most likely when ξ < 0.5, no decrease in pK^obs was observed upon addition of the salts of divalent cations. A competitive effect of Ca²⁺ and Na²⁺ ions on pK^obs in the presence of an excess of Na⁺ ions implied that Ca²⁺ ions at very low concentrations were preferentially, and therefore exhaustively, condensed on the polyanions with sufficiently large ξ probably until effective charge density was lowered to 0.5. The observed difference in the influence of the monovalent and divalent cations on pK^obs was discussed in terms of the difference in the microscopic behavior of the condensed monovalent and divalent cations. © 1993 John Wiley & Sons, Inc.     

Influence of ion size on the stability of chloroplumbates containing PbCl<Stack><Subscript>5</Subscript><Superscript>−</Superscript></Stack> or PbCl<Stack><Subscript>6</Subscript><Superscript>2−</Superscript></Stack>

The enthalpies of formation of PbCl₄, PbCl₅⁻ and PbCl₆²⁻, originating from quantum mechanics, have enabled the thermodynamic behaviour of these ions with respect to Cl-detachment to be assessed. The stability of salts containing PbCl₅⁻ and PbCl₆²⁻ as a function of the dimensions of these anions and complementary cations was studied using an approach combining the Kapustinskii-Yatsimirskii equation with basic thermochemical relationships. It was found that hexachloroplumbates of monovalent metal cations will not dissociate into metal chlorides and PbCl₄, provided the complementary cations are suitably large in size. Hexachloroplumbates of divalent metal cations have not yet been synthesised since no known metal cations attain the requisite large size. Such salts will not dissociate if the divalent metal cations are able to complex suitably large electron-donating ligands. The pentachloroplumbates of both monovalent and divalent metal cations are unstable, since no known metal cations have appropriately large ionic radii. The approach adopted appears to be useful for the examination of the thermal behaviour, stability and reactivity of chloroplumbates.     

A new tripodal anion receptor with selective binding for H2PO4 and F ions

The anions binding properties of the pyrrole-based tripodal anion receptor 1 were studied by X-ray crystallography, ¹H NMR, and ESI-MS. It revealed that this new tripodal receptor has a preference for binding H₂PO₄⁻ and F⁻ ions.     

Highly Selective Methodology for Entrapment and Subsequent Removal of Cobalt (II) Ions under Optimized Conditions by Micellar-Enhanced Ultrafiltration

Micellar-enhanced ultrafiltration (MEUF), being a separation technique, was used to remove cobalt metal ion (Co²⁺) from their aqueous solutions in an application to reduce the toxicity level from industrial effluents using a micellar solution of anionic and cationic surfactants. The metal ions were first adsorbed by using anionic surfactants, i.e., sodium dodecyl sulfate (SDS) and sodium oleate (SO). The calculations for partition (K_x) and binding constants (K_b) and their respective free energy of partition and binding (ΔG_p and ΔG_b kJmol⁻¹) helped significantly to find out the extent of binding or interaction of Co²⁺ with the surfactant and ΔG_p and ΔG_b were found to be −29.50 and −19.38 kJmol⁻¹ for SDS and −23.95 and −12.67 kJmol⁻¹ in the case of SO. MEUF work was also performed to find out the optimal conditions to remove metal pollutants from the aqueous system. For the said purpose, various factors and concentrations effect were studied, such as the concentration of the surfactant, concentration of the electrolyte (NaCl), transmembrane pressure, RPM, and pH. The efficiency of this process was checked by calculating various parameters, such as rejection percentage (R%) and permeate flux (J). A maximum rejection of 99.95% with SDS and 99.99% with SO was attained.     

Determination of equilibrium distribution constants of phenol between surfactant micelles and water using ultrafiltering centrifuge tubes

Equilibrium distribution constants, K_s, of phenol between surfactant micelles and water have been determined by micellar enhanced ultrafiltration (MEUF) using commercial ultrafiltering centrifuge tubes. Three surfactants: sodium dodecyl sulphate (SDS), polyoxyethylene 20 cetyl ether (C16E20) and cetylpiridinium chloride (CPC) were tested with a 10 000 molecular weight cut off (MWCO) membrane. Additionally, membranes of 5000 and 30 000 MWCO were used for CPC. A phenomenological mathematical model has been proposed for the batch MEUF process and checked with the experimental permeate or retentate composition. The model is based on two assumptions: monomeric molecules are not rejected by the membrane and the rejection of micelles is independent of the retentate concentration. The measured micelles rejections for different surfactants and the equivalent molecular weight of the micelles are correlated and they are not significantly affected by the addition of phenol. The estimates of K_s for SDS and CPC agree with previously reported values determined by other methods. K_s values for CPC, calculated using 5000, 10 000 and 30 000 MWCO membranes, have not been significantly different. K_s estimate has allowed to predict the phenol permeate concentration measured in continuous tangential MEUF experiments.     

Counterion binding by poly(styrenesulfonate)

Binding isotherms of poly(styrenesulfonate) with hydrogen and selected alkali ions have been determined by dialysis equilibrium and dye spectroscopy, employing Pb²⁺, Mg²⁺, and Ca²⁺ as the competing divalent ions. The observed degrees of counterion binding, Θ_z, defined as the number of bound counterfoils of valence z per poly ion site-group, agree quite well with those predicted by Manning's two variable theory. The binding preference follows the order Cs⁺ > Rb⁺ > K⁺ > Na⁺ > H⁺ >Li⁺, indicating that the binding process is of a territorial nature. Independently performed light scattering measurements show that a plot of the radius of gyration, >S _z>, against the actual polyion charge gives a sigmoidal curve. This result is taken to indicate that (1) a polyion is, in general, not completely neutralized in the Θ-state and that (2) a polyion may be not fully stretched when the polyion charge density is largest.     

Relative efficiencies of substituted aromatic monocarboxylic acids as eluents in ion chromatographic separation of inorganic and organic anions

The eluent strengths of para, ortho and meta substituted hydroxy-, nitro-, amino- and sulfobenzoic acids in single column ion chromatographic separations of inorganic and organic anions have been evaluated and compared with benzoic acid.o-Sulfobenzoic acid turns out to be a stronger and efficient eluent compared to others for the separation and determination of monovalent (Cl^–, NO ₂ ^– , Br^–, NO ₃ ^– ) and divalent (SO ₄ ^2– , SeO ₄ ^2– , S₂O ₃ ^2– , S₂O ₆ ^2– ) inorganic anions. In addition it also functions as an appropriate mobile phase for the detection and quantification of some substituted benzoate ions in an aqueous medium.     

Influence of ionic composition in aqueous solution on wettability of rock surface-experiment and economics evaluation

In this study, the influence of different ionic composition in aqueous solution on the minerals surface wettability was studied. The differences effect of monovalent ion and divalent ions onto the wettability alteration were studied. The anions were Cl^- and SO₄^2-. The SO₄^2- could make the minerals surface more hydrophilic. Besides, the influence of NaCl, MgCl₂, CaCl₂, Na₂SO₄, K₂SO₄ and MgSO₄ on the mineral wettability alteration were studied. The results indicated that divalent ions showed significant impact on the minerals wettability alteration, compared with monovalent ion. The reasons were due to the fact that divalent ions showed higher ions adsorption than monovalent ion, and divalent ions have higher effect on compressing the electric double layer. The static contact angle and dynamic contact angle were measured. Different heavy oils were studied, including heavy oil with 100 ppm, heavy oil, heavy oil without resins, heavy oil without asphaltenes. The results showed that the asphaltenes would make it difficult for the heavy oils to liberate from minerals, thus decreasing the oil drops contact angle. Then the resins would decrease the heavy oil contact angles. CaCl₂/MgCl₂ and K₂SO₄ have synergistic effect on the change of the minerals surface wettability. Atomic force microscope (AFM) measurement indicated that the ions would effectively decrease the interaction force on the surface of heavy oil-minerals, which was beneficial to the heavy oil liberation. The roughness measurement indicated that the different ions would effectively increase the minerals surface wettability.     

Urea and thiourea based efficient colorimetric sensors for oxyanions

Urea and thiourea based receptors 1 and 2 bind H₂PO₄⁻, OH⁻, CH₃CO₂⁻, and PhCO₂⁻ ions in an acetonitrile/DMSO (9:1, v/v) medium. Binding of these anions causes an appreciable change in the visible region of the spectrum, which can be detected by the naked eye. The affinity constant for H₂PO₄⁻ is higher by about an order of magnitude as compared to the other oxyanions mentioned above. Ab initio calculations predicted tweezer-like binding modes for receptors 1 and 2 with these anions and a higher affinity toward H₂PO₄⁻ was predicted in acetonitrile.     

A combined osmotic pressure and cake filtration model for crossflow nanofiltration of natural organic matter

A combined osmotic pressure and cake filtration model for crossflow nanofiltration of natural organic matter (NOM) was developed and successfully used to determine model parameters (i.e. permeability reduction factor (η) and specific cake resistance (α_cake)) for salt concentrations, NOM concentrations, and ionic strength of salt species (Na⁺ and Ca⁺⁺). In the absence of NOM, with increasing salt concentration from 0.004 to 0.1 M, permeability reduction factor (η)) decreased from 0.99 to 0.72 and 0.94 to 0.44 for monovalent cation (Na⁺) and divalent cation (Ca⁺⁺), respectively. This reduced membrane permeability was due to salt concentrations and salt species. In the presence of NOM, specific cake resistance tended to increase with increasing NOM concentration and ionic strength in the range of 0.85 × 10¹⁵–3.66 × 10¹⁵ m kg⁻¹. Solutions containing divalent cation exhibited higher normalized flux decline (J_v/J_vo = 0.685–0.632) and specific cake resistance (α_cake = 2.89 × 10¹⁵–6.24 × 10¹⁵ m kg⁻¹) than those containing monovalent cation, indicating a highly compacted NOM accumulation, thus increased permeate flow resistance during NF filtration experiments. After membrane cleaning, divalent cation exhibited lower water flux recovery than monovalent cation, suggesting higher non-recoverable (R_non-rec) resistance than monovalent cation.     

Removal of heavy metals from wastewater using micellar enhanced ultrafiltration technique: a review

Application of Micellar enhanced ultrafiltration (MEUF) for the removal of different heavy metals has been reviewed. It is considered an economical alternative available to the conventional membrane separation process, because it reduces the requirement of higher pressure and high membrane costs. MEUF is a separation processes which uses surfactants and ultrafiltration membranes to remove multivalent ions from wastewater with high percent rejection using electrostatic attraction between metals and micelles.     

Synthesis of arylselenide ethers by photoinduced reactions of selenobenzamide, selenourea and selenocyanate anions with aryl halides

Selenobenzamide (⁻SeCNH(Ph), 1), selenourea (⁻SeCNH(NH₂), 2) and selenocyanate (⁻SeCN, 3) anions afford areneselenolate ions (ArSe⁻) under photostimulation in the presence of tert-butoxide or 2-naphthoxide ions as electron donors (entrainment conditions) in DMSO. In a ‘one-pot’ procedure, ArSe⁻ anions can be trapped by a subsequent aliphatic nucleophilic substitution giving aryl methyl selenides in good to excellent yields (67-100%). This simple approach is compatible with electron-donating and electron-withdrawing substituents, such as nitro and carbonyl groups.     

Rod-like polyelectrolyte adsorption onto charged surfaces in monovalent and divalent salt solutions

We analyze the adsorption of strongly charged polyelectrolytes onto weakly charged surfaces in divalent salt solutions. We include short-range attractions between the monomers and the surface and between condensed ions and monomers, as well correlations among the condensed ions. Our results are compared with the adsorption in monovalent salt solutions. Different surface charge densities (σ), and divalent (m) and monovalent (s) salt concentrations are considered. When the Wigner-Seitz cells diameter (2R) is larger than the length of the rod, the maximum amount of adsorption scales like n_max ∼ σ^4/3 in both monovalent and divalent solutions. For homogeneously charged surfaces, the maximum adsorption occurs at s* ∼ σ² when s* > ϕ, where ϕ is the monomer concentration, the counterpart for divalent salt solution, m* roughly scales as σ^2.2 when m* > ϕ. The effective surface charge density has a maximum absolute value at m′ < m*. A discrete surface charge distribution and short-range attractions between monomers and surface charge groups can greatly enhance surface charge inversion especially for high salt concentration. The critical salt concentration for adsorption in divalent salt solution roughly scales as m_c ∼ bσ^1.9, where b is the distance between two neighboring charged monomers. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3642–3653, 2004     

Equilibrium analysis of reactions between aromatic anions and nonionic surfactant micelles by capillary zone electrophoresis.

Separability of some positional isomers of aromatic anions by capillary zone electrophoresis was improved by adding nonionic surfactants to a migrating solution. Eleven kinds of aromatic anions, including positional isomers, were used as analytes, and Brij-35, Brij-58 and Brij-78 were investigated as nonionic surfactants to form micelles, where hydrophobicities are different from each other. Increasing the concentration of the surfactants developed the separability of the anionic isomers. The interaction between the anions and the nonionic surfactant micelles is also investigated through the change in the electrophoretic mobility, and the binding constants are determined. Apparent electrophoretic mobility of the anions decreased with increasing concentrations of the nonionic surfactants. The decrease in the mobility, as well as the binding constant, was larger in the monovalent anions than in the divalent anions, which indicates that the interaction or reactivity of the monovalent analytes is higher than that of the divalent analytes. The reactivity of each anion was almost identical even when the kinds of the surfactants were changed, suggesting that the hydrophobicity of the polyoxyethylene group in the surfactant would have the main role for binding the analytes. The reactivity tendency among the positional isomers was almost similar to that in ion association-capillary zone electrophoresis using tertabutylammonium ion as a pairing ion. The results obtained in this work suggest that the anions are bound to the micelles by the hydrophobic interaction between analyte anions and the polyoxyethylene moiety of the surfactant micelles. Changes in the fluorescence intensity of the anions were also investigated; the results can explain well the mobility changes of the analytes.     

Influence of inorganic scalants and natural organic matter on nanofiltration membrane fouling

The influence of inorganic scalants and NOM on nanofiltration (NF) membrane fouling was investigated by a crossflow bench-scale test cell. Mathematical fouling models were used to determine kinetics and fouling mechanisms of NF membrane. It was observed that, with natural organic matter (NOM) at a concentration of 10 mg L⁻¹, divalent cation, i.e. calcium (Ca²⁺), exhibited greater flux decline than monovalent cation, i.e. sodium (Na⁺), while solution flux curves dominated cake formation model, especially at high ionic strength. For inorganic scalants of polyanions, i.e. carbonate (CO₃²⁻), sulphate (SO₄²⁻), and phosphate (PO₄³⁻), solution flux curves were relatively fitted well with pore blocking model, possibly due to precipitated species formed and blocked on membrane surface and/or pores. For different divalent cations (i.e. calcium and magnesium (Mg²⁺)), calcium showed greater flux decline than magnesium, possibly due to higher concentration of precipitated calcium species than that of precipitated magnesium species based on the pC (−log concentration) and pH diagram.