Sulfonated poly(ether sulfone)/sulfonated polybenzimidazole blend membrane for fuel cell applications

Polymer blending is used to modify or improve the dimensional and thermal stability of any two different polymers or copolymers. In this study, both sulfonated polybenzimidazole homopolymer (MS-p-PBI 100) and sulfonated poly(aryl ether benzimidazole) copolymers (MS-p-PBI 50, 60, 70, 80, 90) were successfully synthesized from commercially available monomers. The chemical structure and thermal stability of these polymers was characterized by ¹H NMR, FT-IR and TGA techniques. Blend membranes (BMs) were prepared from the salt forms of sulfonated poly(ether sulfone) (PES 70) and MS-p-PBI 100 using dimethylacetamide (DMAc). These blend membranes exhibited good stability in boiling water. The blending of 1 wt.% of MS-p-PBI 100 and 99 wt.% of PES 70 to produce the blend membrane BM 1 reduced membrane swelling, thus leading to good dimensional stability and comparable proton conductivity. Hence, BM 1 was chosen for the fabrication of a membrane electrode assembly (MEA) for proton exchange membrane fuel cell (PEMFC) and direct methanol fuel cell (DMFC) applications. This paper reports on PEMFC and DMFC performance under specific conditions.     

Poly(arylene ether) ionomers containing sulfofluorenyl groups: Effect of electron-withdrawing groups on the properties

For polymer electrolyte membrane fuel membrane cell (PEMFC) applications, the effect of electron-withdrawing groups on the properties of sulfonated poly(arylene ether) (SPE) ionomer membranes was investigated. A series of poly(arylene ether)s containing fluorenyl groups and electron-withdrawing groups (sulfone, nitrile, or fluorine) was synthesized, which were sulfonated with chlorosulfonic acid using a flow reactor to obtain the title ionomers. The ionomers had high molecular weight (M_n > 77 kDa, M_w > 238 kDa) and gave tough, ductile membranes by solution casting. The ion exchange capacity (IEC) of the membranes ranged from 1.6 to 3.5 mequiv/g as determined by titration. The electron-withdrawing groups did not appear to affect the thermal properties (decomposition temperature higher than 200 °C). The presence of nitrile groups, especially at positions meta to the ether linkages, improved the oxidative stability of the SPE membranes, while it led to a deterioration of the hydrolytic stability. The perfluorinated biphenylene groups were effective in providing high mechanical strength with reasonable dimensional change, probably due to a somewhat decreased water absorbability. The SPE membrane containing sulfone groups showed the highest proton conductivity (10⁻³-10⁻¹ S/cm) at 20-93% RH (relative humidity) and 80 °C. The nitrile-containing SPE membrane showed smaller apparent activation energies for oxygen and hydrogen permeability and is thus considered to be a possible candidate for applications in PEMFCs.     

Direct copolymerization of sulfonated poly(phthalazinone arylene ether)s for proton‐exchange‐membrane materials

Sulfonated poly(phthalazinone ether ketone) (SPPEK) copolymers and sulfonated poly(phthalazinone ether sulfone) (SPPES) copolymers containing pendant sodium sulfonate groups were prepared by direct copolymerization. The reaction of disodium 3,3′‐disulfonate‐4,4′‐difluorobenzophenone (SDFB‐Na), 4,4′‐difluorobenzophenone (DFB), and 4‐(4‐hydroxyphenyl)‐1(2H)‐phthalazinone (DHPZ) at 170 °C in N‐methyl‐2‐pyrrolidione containing anhydrous potassium carbonate gave SPPEKs. SPPESs were similarly obtained with 3,3′‐disulfonate‐4,4′‐difluorophenyl sulfone, 4‐fluorophenyl sulfone (DFS), and DHPZ as monomers. The sulfonic acid groups, being on deactivated positions of the polymer backbone, were expected to be hydrolytically more stable than postsulfonated polymers. Fourier transform infrared and ¹H NMR were used to characterize the structures and degrees of sulfonation of the sulfonated polymers. Membrane films of SPPEKs with SDFB‐Na/DFB molar feed ratios of up to 60/40 and SPPESs with sulfonated 4‐fluorophenyl sulfone/DFS molar feed ratios of up to 50/50 were cast from N,N‐dimethylacetamide polymer solutions. Membrane films in acid form were then obtained by the treatment of the sodium‐form membrane films in 2 N sulfuric acid at room temperature. An increase in the number of sulfonate groups in the copolymers resulted in an increased glass‐transition temperature and enhanced membrane hydrophilicity. The sodium‐form copolymers were thermally more stable than their acid forms. The proton conductivities of the acid‐form copolymers with sulfonated monomer/unsulfonated monomer molar feed ratios of 0.5 and 0.6 were higher than 10^?2 S/cm and increased with temperature; they were less temperature‐dependent than those of the postsulfonated products. SPPESH‐50 showed higher conductivity than the corresponding postsulfonated poly(phthalazinone ether sulfone). © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2731–2742, 2003     

Effects of the structure on the properties of new poly(arylene ether sulfone)s containing naphthalene units

A series of new poly(arylene ether sulfone)s has been obtained by solution condensation polymerisation starting from 1,5- and 2,6-bis-(4-fluorosulfonyl)naphthalene with various aromatic dihydroxy compounds. The polymers, obtained in quantitative yields, possessed inherent viscosities in the range 0.28-0.68 dl g⁻¹, had good thermal stability (10% weight loss temperatures were above 405 and 420 °C respectively in nitrogen and air) and high glass transition temperatures (in the range 217-258 °C). They have been characterised by elemental and infrared analyses, GPC and wide-angle X-ray diffraction. The properties of these poly(arylene ether sulfone)s have been compared with those of the corresponding poly(arylene ether ketone)s.     

High performance nitrile copolymers for polymer electrolyte membrane fuel cells

This paper reports the fuel cells (DMFC and PEMFC) performance using sulfonated poly(arylene ether ether nitrile) (SPAEEN) copolymers containing sulfonic acid group arranged in structurally different ways. The membrane electrode assembly (MEA) fabricated from SPAEEN containing 60 mol% of angled naphthalenesulfonic acid group (m-SPAEEN-60) had superior performance over those derived from pendent naphthalenesulfonic acid group (p-SPAEEN) or sulfonated hydroquinone (HQ-SPAEEN) in H₂/air and/or DMFC conditions. For example, the current density of the MEA using m-SPAEEN-60 at 0.5 V and 2.0 M methanol was 250 mA/cm², whereas the current densities of the MEAs using p-SPAEEN-50 and HQ-SPAEEN-56 were 185 and 190 mA/cm², respectively. In addition, compared with the sulfonated polysulfone (BPSH-35) and Nafion membranes, the copolymer containing nitrile group showed the improved cell performance. For example, the power density of the MEA using m-SPAEEN-60 at 250 mA/cm² and 2.0 M methanol was 125 mW/cm², whereas the power densities of the MEAs using sulfonated polysulfone (BPSH-35) and Nafion were 115 and 113 mW/cm², respectively. m-SPAEEN-60 showed stable cell performance during extended operation (>100 h).     

Preparation and properties of UV irradiation-induced crosslinked sulfonated poly(ether ether ketone) proton exchange membranes

The crosslinkable sulfonated poly(ether ether ketone)s (SPEEKs) were synthesized by nucleophilic substitution reaction of diallyl bisphenol A, tert-butylhydroquinone, 4,4′-difluorobenzophenone and sodium 5,5′-carbonylbis(2-fluorobenzene-sulfonate). The SPEEKs with high intrinsic viscosity showed good solubility and could be cast into flexible and transparent membranes. The SPEEK membranes containing benzophenone (BP) and triethylamine (TEA) photo-initiator system were treated by UV light to promote crosslinking. The experimental results revealed that the crosslinked membrane with 10 min irradiation time showed the most potential as proton exchange membrane for direct methanol fuel cell applications. When the irradiation time increased from 0 to 10 min, the water uptake decreased from 29.1 to 26.1%, and the tensile modulus and the tensile strength enhanced sharply from 0.80 to 1.44 GPa and from 40.3 to 63.4 MPa, respectively. In addition, the methanol diffusion coefficient reduced sharply from 1.70 × 10⁻⁶ to 7.42 × 10⁻⁷ cm²/s with only slight sacrifice in the proton conductivity, which made the crosslinked membrane with 10 min irradiation time possess the highest selectivity.     

Locally sulfonated poly(ether sulfone)s with highly sulfonated units as proton exchange membrane

Novel locally sulfonated poly(ether sulfone)s with highly sulfonated units were successfully synthesized for fuel cell applications. Poly(ether sulfone)s were prepared by the nucleophilic substitution of bis(4‐fluorophenyl) sulfone with 1,2,4,5‐tetrakis([1,1′‐biphenyl]‐2‐oxy)‐3,6‐bis(4‐hydroxyphenoxy)benzene and bis(4‐hydroxyphenyl) sulfide, followed by oxidation using m‐chloroperoxybenzoic acid. The desired highly sulfonated units were easily introduced by postsulfonation and each one had ten sulfonic acid groups. The sulfonated polymers gave tough, flexible, and transparent membranes by solvent casting. The high contrast in polarity between highly sulfonated units and hydrophobic poly(ether sulfone) units enabled the formation of defined phase‐separated structures and well‐connected proton paths. The sulfonated polymers exhibited excellent proton conductivity over a wide range of relative humidities. The proton conductivity of the sulfonated polymer with an ion exchange capacity value of 2.38 mequiv/g was comparable to that of Nafion 117 even at 30% relative humidity. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3444–3453, 2009     

Fluorene-containing block sulfonated poly(ether ether ketone) as proton-exchange membrane for PEM fuel cell application

A series of sulfonated block poly(ether ether ketone)s with different sulfonic acid group clusters were successfully synthesized by nucleophilic displacement condensation. Membranes were accordingly cast from their DMSO solutions, and fully characterized by determining the ion-exchange capacity, water uptake, proton conductivity, dimensional stabilities and mechanical properties. The experimental results showed that the main properties of the membrane can be tailored by changing the cluster size of sulfonic acid groups. The membrane of block-7c(40) has good mechanical, oxidative and dimensional stabilities together with high proton conductivity (5.09 × 10⁻² S cm⁻¹) at 80 °C under 100% relative humidity. The membranes also possess excellent thermal and dimensional stabilities. These polymers are potential and promising proton conducting membrane material for PEM full cell applications.     

Side-Chain Sulfonated Poly(arylene ether)s for Fuel Cell Applications

Summary: Poly(arylene ether sulfone)s of high molecular weight and narrow molecular weight distribution were obtained by melt polycondensation of 4,4′-difluorodiphenyl- sulfone and trimethylsilylethers of 4,4′-dihydroxydiphenylsulfone and phenylhydroquinone using CsF as catalyst. Although a block-like structure of the polymers could be expected from the course of reaction, only a single T_g ranging from 190 °C to 230 °C could be detected by DSC and which depended on the copolymer composition. Contrary to the sulfonation of similar poly(ether ether ketone)s the poly(arylene ether sulfone)s here reported were sulfonated both in the side chain and the main chain. Nonetheless the sulfonated poly(arylene ether sulfone)s showed high hydrolytic stability in water at 130 °C.     

非含氟型磺化聚合物质子交换膜材料的研究进展(上)

概述了近十年来非含氟型磺化聚合物质子交换膜材料的研究进展,包括各种材料的制备和性质,详细地讨论了材料的化学结构、形态与其性能(质子导电率、耐水性、尺寸稳定性、吸水率、抗自由基氧化性、甲醇透过率等)之间的关系,其中结合作者在磺化聚酰亚胺方面的研究工作,重点对这类材料进行了系统、深入的介绍和讨论.最后,本文还对今后燃料电池用质子交换膜材料的研究提出了一些设想和展望.本文分为上下两篇,其中上篇主要综述了各种非含氟型磺化聚合物的制备方法.     

Graft‐crosslinked Copolymers Based on Poly(arylene ether ketone)‐gc‐sulfonated Poly(arylene ether sulfone) for PEMFC Applications

Novel poly(arylene ether ketone) polymers with fluorophenyl pendants and phenoxide‐terminated wholly sulfonated poly(arylene ether sulfone) oligomers are prepared via Ni(0)‐catalyzed and nucleophilic polymerization, respectively, and subsequently used as starting materials to obtain graft‐crosslinked membranes as polymer electrolyte membranes. The phenoxide‐terminated sulfonated moieties are introduced as hydrophilic parts as well as crosslinking units. The chemical structure and morphology of the obtained membranes are confirmed by ¹H NMR and tapping‐mode AFM. The properties required for fuel cell applications, including water uptake and dimensional change, as well as proton conductivity, are investigated. AFM results show a clear nanoscale phase‐separation microstructure of the obtained membranes. The membranes show good dimensional stability and reasonably high proton conductivities under 30–90% relative humidity. The anisotropic proton conductivity ratios (σ_⟂/||) of the membranes in water are in the range 0.65–0.92, and increase with an increase in hydrophilic block length. The results indicate that the graft‐crosslinked membranes are promising candidates for applications as polymer electrolyte membranes.

     

新型直接交联磺化聚芳醚砜燃料电池用质子交换膜的合成及性能

以4,4′-二氟二苯砜、4,4′-联苯二酚、3,3′-二磺化-4,4′-二氟二苯砜二钠盐和三羟基苯为原料, 经高温溶液缩聚反应, 制备了一系列不同磺化度的新型交联磺化聚芳醚砜(CSPAES). 利用1H NMR和FTIR对聚合物结构进行表征. 采用溶液浇铸法制备了聚合物膜. 对膜的离子交换容量、吸水率、尺寸变化、机械性能和质子导电率进行了分析. 结果表明, 通过交联处理的磺化聚芳醚砜的水溶胀性明显降低, 当IEC为2.43时, CSPAES膜M(6/4-5)在水中的质子导电率达到260.5 mS/cm, 约为相同条件下Nafion112的2倍.     

Sulfur-containing polymers. Synthesis and properties of novel poly(arylene thioether)s based on 2,2-bis(4-mercaptophenyl)propane

Novel poly(arylene thioether)s were synthesised using the one pot polymerisation method from the bis(N,N-dimethyl-S-carbamate) of 2,2-bis(4-mercaptophenyl)propane and activated difluoro aromatic compounds. Each of the polymers, obtained in good yields and with fairly high molecular weights, were characterised by IR, GPC and NMR analyses. In particular, the NMR characterisation was performed using ¹H NMR, ¹³C NMR, DEPT, 2D COSY and 2D HSQC experiments. To study the effect on the thermal properties of replacing the ethereal oxygen atoms with sulfur atoms, we have synthesised the counterparts, the poly(arylene ether)s, with similar molecular weights. We observed that the substitution of the ethereal oxygen atoms with sulfur atoms results in a slightly lower thermal stability for the poly(thioether ketone)s, both under nitrogen and in air, and does not modify the T_g values. For the poly(thioether sulfone), on the other hand, the thermal stability is equal to that of the poly(ether sulfone), while the T_g is 10 °C lower. Furthermore, each sample is completely amorphous, with the exception of one of the poly(thioether ketone)s (sample 1b), which shows the capacity to crystallise, even if with a very slow crystallisation kinetics.     

Preparation and characterization of branched and linear sulfonated poly(ether ketone sulfone) proton exchange membranes for fuel cell applications

Branched sulfonated poly(ether ketone sulfone)s (Br‐SPEKS) were prepared with bisphenol A, bis(4‐fluorophenyl)sulfone, 3,3′‐disodiumsulfonyl‐4,4′‐difluorobenzophenone, and THPE (1,1,1‐tris‐p‐hydroxyphenylethane), respectively, at 180 °C using potassium carbonate in NMP (N‐methylpyrrolidinone). THPE, as a branching agent, was used with 0.4 mol % of bisphenol A to synthesize branched copolymers. Copolymers containing 10–50 mol % disulfonated units were cast from dimethylsulfoxide solutions to form films. Linear sulfonated poly(ether ketone sulfone)s (SPEKS) were also synthesized without THPE. The films were converted from the salt to acid forms with dilute hydrochloric acid. A series of copolymers were studied by Fourier transform infrared, ¹H‐NMR spectroscopy, differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). Sorption experiments were conducted to observe the interaction of sulfonated polymers with water and methanol. The ion‐exchange capacity (IEC), a measure of proton conductivity, was evaluated. The synthesized Br‐SPEKS and SPEKS membranes exhibit conductivities (25 °C) from 1.04 × 10^?3 to 4.32 × 10^?3 S/cm, water swell from 20.18 to 62.35%, IEC from 0.24 to 0.83 mequiv/g, and methanol diffusion coefficients from 3.2 × 10^?7 to 4.7 × 10^?7 cm²/S at 25 °C. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1792–1799, 2008     

Sulfonated poly(fluorene-co-sulfone)ether membranes containing perfluorocyclobutane groups for fuel cell applications

A new class of sulfonated poly(fluorene-co-sulfone)ether membranes containing perfluorocyclobutane (PFCB) groups were synthesized and characterized in terms of their electrochemical properties as proton exchange membranes for fuel cells. Two monomers, 9,9-bis(4-trifluorovinyloxyphenyl)fluorene and 4,4′-sulfonyl-bis(trifluorovinyloxy)biphenyl were synthesized and statistically copolymerized by thermal [2π + 2π] cycloaddition to yield a series of polymers containing 0–60 mol% of fluorenyl content (PFS-X). The copolymers were then sulfonated using chlorosulfonic acid to afford five kinds of ionomers with different sulfonation levels (SPFS-X), which were cast into membranes and analyzed in terms of electrochemical properties. It was found that the ion exchange capacity (IEC), water uptake, proton conductivity and methanol permeability values of SPFS-X increased with the increment of the sulfonated fluorenyl content. The proton conductivities of SPFS-50 and -60 with high IECs and water uptake values were higher than those of Nafion-115 between 25 and 80 °C. The methanol permeability of SPFS-X was considerably lower than that of Nafion-115.     

Sulfonated poly(ether ether ketone) as an alternative charged material to poly(vinyl chloride) in the design of ion-selective electrodes

To date, poly(vinyl chloride) (PVC) is the most used polymer in the design of ion selective electrode (ISE) membranes. This paper is focused on the use of sulfonated poly(ether ether ketone) (SPEEK) as an alternative material to PVC for the design of ISEs. SPEEK of the desired degree of sulfonation is synthesized from poly(ether ether ketone) (PEEK). An NH₄⁺-ISE has been chosen as a model electrode to study the efficiency of SPEEK as polymer matrix of the membrane. The material was evaluated in ionophore free ion exchanger membranes as well as in ion-selective electrodes membranes containing nonactine as ionophore. Analytical performance parameters of the prepared electrodes were evaluated. The electrodes show a slope between 50 and 60 mV dec⁻¹ depending on both the calibration medium and the membrane composition. A linear range of response between 10⁻⁴ and 1.0 M and a lifetime of 1-2 months were obtained. The interferences of cations such us Ca²⁺, Na⁺, Li⁺ and K⁺ over the prepared ISEs are studied as well. Although the plasticizer in the SPEEK based membrane matrix is not necessary, its presence improves the sensibility. This makes SPEEK a good potential choice over alternative membrane matrices reported in the literature and a promising platform for the establishment of membrane components.     

Characterization and performance of proton exchange membranes for direct methanol fuel cell: Blending of sulfonated poly(ether ether ketone) with charged surface modifying macromolecule

Modification of sulfonated poly(ether ether ketone) (SPEEK) membrane was attempted by blending charged surface modifying macromolecule (cSMM). The modified membrane was tested for direct methanol fuel cell (DMFC) application; i.e. a SPEEK/cSMM blend membrane was compared to a SPEEK membrane and a Nafion 112 membrane for the thermal and mechanical stability, methanol permeability, and proton conductivity. Thermal and mechanical stability of the blended membrane were slightly reduced from the SPEEK membrane but still higher than the Nafion 112 membrane. The blend membrane was found to be promising for DMFC applications because of its lower methanol diffusivity (2.75 × 10⁻⁷ cm² s⁻¹) and higher proton conductivity (6.4 × 10⁻³ S cm⁻¹), than the SPEEK membrane. A plausible explanation was given for the favorable effect of cSMM blending.     

Synthesis and characterization of poly(aryl ether ketone) ionomers with sulfonic acid groups on pendant aliphatic chains for proton-exchange membrane fuel cells

A series of parent poly(aryl ether ketone)s bearing different content of unsaturated pendant propenyl groups were synthesized via nucleophilic substitution polymerization from 3,3′-diallyl-4,4′-dihydroxybiphenyl, 9,9′-bis(4-hydroxyphenyl) fluorene and 4,4′-difluorobenzophenone. The polymers with pendant aliphatic sulfonic acid groups were further synthesized by free radical thiol-ene coupling reactions between 3-mercapto-1-propanesulfonic sodium and the parent propenyl functional copolymers. The resulting sulfonated polymers with high inherent viscosity (1.83-4.69 dL/g) were soluble in polar organic solvents and can form flexible and transparent membranes by casting from their solutions. The copolymers with different ion exchange capacity could be conveniently synthesized by varying the monomers ratios. Transmission electron microscopy (TEM) was used to examine the microstructures of the membrane and the results revealed that significant hydrophilic/hydrophobic microphase separation with spherical, uniform-sized (5-10 nm) and well-dispersed hydrophilic domains was afforded. The proton conductivities of the as-prepared membranes and the state-of-the-art Nafion 117 membrane in fully hydrated state were investigated. The results revealed that the proton conductivity of the synthesized membranes increased more remarkably than that of Nafion 117 membrane with increasing temperature. The membrane with 1.69 mequiv/g of IEC had a conductivity of 2.5 × 10⁻² Scm⁻¹ at 100 °C. The membranes also possessed excellent mechanical properties, good thermal, oxidative, hydrolytic and dimensional stabilities.     

Sulfonated poly(fluorenyl ether) membranes containing perfluorocyclobutane groups for fuel cell applications

This paper describes the preparation and electrochemical properties of new proton conducting polymer membranes, sulfonated poly(fluorenyl ether) membrane-containing perfluorocyclobutane (PFCB) moieties for fuel cell applications. The sulfonated polymers were prepared via thermal cyclodimerization of 9,9-bis(4-trifluorovinyloxyphenyl)fluorene and subsequent post-sulfonation using chlorosulfonic acid (CSA) as a sulfonating agent. The post-sulfonation reaction was carried out by changing the molar ratio of CSA/repeating unit of the polymer at room temperature for 5 h and the resulting sulfonated polymers showed different degrees of sulfonation (DS) and ion exchange capacities (IEC). With the increment of CSA content, the DS, IEC and water uptake of the sulfonated polymer membranes increased. Their proton conductivity was investigated as a function of temperature. The polymer membrane with an IEC value of 1.86 mmol/g showed a water content of 25% similar to Nafion-115's but showed higher proton conductivity than Nafion-115 over the temperature 25–80 °C. The polymer membrane with lower water uptake and higher IEC showed similar proton conductivity and methanol permeability to Nafion-115. These results confirmed that the sulfonated poly(fluorenyl ether)-containing PFCB groups could be a promising material for fuel cell membranes.     

Selectively sulfonated poly(aryl ether sulfone)‐b‐polybutadiene for proton exchange membrane

A series of selectively sulfonated poly(arylene ether sulfone)‐b‐polybutadiene copolymers (SPAES‐b‐PB) were prepared based on carboxyl terminated polybutadiene (CTPB) and sulfonated poly(arylene ether sulfone) (SPAES) that was directly prepared by polycondensation of 4,4′‐isopropylidenediphenol with different molar ratios of disodium 3,3′‐disulfonate‐4,4′‐dichlorodiphenyl sulfone (SDCDPS) to 4,4′‐dichlorodiphenylsulfone (DCDPS), and subsequent selective postsulfonation of flexible PB block was carried out. Epoxidized modification of membranes was conducted by an in situ‐generated peracid method. The content of sulfonic acid groups attaching to aromatic rings in SPAES was determined by ¹H NMR and was in good aggrement with the controlled ratios. The effect of sulfonated rigid blocks on the postsulfonation of PB blocks was studied by Fourier transform infrared spectroscopy. The glass transition temperature (T_g) and the temperature of the melting peak (T) of membranes in acid form were studied by differential scanning calorimetry. Fenton's reagent test revealed that the selectively sulfonated SPAES‐b‐PB membranes had good stability to oxidation. The microstructure of rod‐like rigid SPAES blocks and interpenetrating network of ions were observed by transmission electron microscopy. Complex impedance measurement showed that an epoxidized membrane with SPAES‐40 exhibited the highest proton conductivity (1.08 × 10^?1 S/cm, 90 °C), which was due to the formation of obvious ionic networks. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 665–672, 2006