The Use of PAMAM Dendrimers as a Platform for Laccase Immobilization: Kinetic Characterization of the Enzyme

The kinetic behavior of the enzyme laccase in solution and immobilized onto carbon platforms using poly(amido amine) (PAMAM) dendrimers has been investigated. The results with the immobilized enzymes have demonstrated that almost ten times more enzyme on the carbon support is required for satisfactory kinetic rates to be achieved. Furthermore, the study as a function of the substrate concentration revealed that the kinetic behavior of the enzyme in solution fits the Michaelis?CMenten model. However, when the enzyme is immobilized onto the carbon surface, the catalyzed reaction follows a particular kinetic behavior with apparent positive cooperativity. The highest activity with laccase (in solution or immobilized) is achieved around pH?4.5, and the substrate conversion rate clearly diminishes with rising pH. The optimum temperature lies around 60?°C. The enzyme displays good catalytic activity in a wide range of pH and temperature values. The stability tests evidenced that there is no appreciable reduction in the enzymatic activity after immobilization within the first 30?days. Taking into account both the kinetic and stability tests, one can infer that the use of PAMAM dendrimers seems to be a very attractive approach for the immobilization of enzymes, as well as a feasible and useful methodology for the anchoring of enzymes with potential application in many biotechnological areas.     

以HPD-750大孔树脂为载体材料固定化果胶酶

HPD-750树脂是中极性大孔吸附树脂,生物相容性好,机械性能稳定,具有较大的比表面积,可用于固定化酶载体材料。本文以HPD-750大孔树脂为载体固定化果胶酶,研究各因素对固定化酶的影响,并采用正交试验对固定化条件进行优化。结果表明,当pH为4.0、固定化温度为45℃、固定化时间为4h、加酶量为0.16g/mL时,固定化酶活力可达5146U/mg。以HPD-750大孔树脂为载体材料制备的固定化酶相较于游离酶具有更好的酸碱稳定性和热稳定性。在循环使用10次后,酶活力依然保留80%以上;4℃储藏25d之后,其酶活力仍保留60%以上。与D311大孔树脂、聚丙烯酰胺和海藻酸钠微球制备的固定化酶相比,HPD-750大孔树脂固定化酶的活性、操作稳定性、机械稳定性和储存稳定性都较好。该结果说明,HPD-750大孔树脂可作为固定化酶较好的载体材料。     

Immobilization of glucose oxidase on nylon membranes and its application in a flow-through glucose reactor

The immobilization of glucose oxidase on hydrolyzed nylon-6,6 was studied. Various spacers were introduced on the support before the coupling of the enzyme. Best results were obtained when the membrane was covered with denatured bovine serum albumin (BSA) before spacer coupling and immobilization of glucose oxidase (GOD). The influence of various factors (pH, ionic strength, etc.) on the activity of the free and immobilized enzyme was investigated. It was found that the behavior of the fixed glucose oxidase and the free enzyme is very similar. The covalently immobilized enzyme had a lifetime of around 2 months (50% of initial activity).     

Temperature-dependent behavior of immobilized alkaline phosphatase. I. Role of working conditions and pH during coupling

Alkaline phosphatase from hog intestine was immobilized to controlled-pore glass under various conditions. The specific activity of the enzyme was not diminished by immobilization. The influence of temperature and pH on the behavior and the stability of the immobilized enzyme preparations is discussed and compared to that of the native enzyme.     

Properties of pectinesterase immobilized on glycophase-coated controlled-pore glass

Pectinesterase was immobilized on a porous glass support, which surface was covered with glyceryl residues. The parameters of the immobilization were characterized with respect to the coupling method used as well as the support pore size. Chemical modification level resulted an important parameter in determining the activity of the immobilized derivative. Attachment of the enzyme through thiol groups gave the best results, whereas a nominal pore size of 20 nm seemed to be the most suitable for the demethoxylating activity of the enzyme on citrus pectin. Optimum conditions for activity as well as the inhibition constant for polygalacturonic acid did not change on immobilization, as the Michaelis constant did. Fluorescence spectra revealed a partial unfolding of the enzyme tertiary structure when immobilized.     

大尺寸SiO2大孔材料固定化漆酶

以表面固定Cu2+的改性大尺寸SiO2大孔材料作为载体,考察了时间、pH和给酶量对漆酶固定化效果的影响,并对固定化漆酶的活性和稳定性进行了研究。结果表明:5 h时吸附达到平衡,pH为4.5、漆酶与载体比例为5 mg·g-1时固定化效果最好,酶活回收率可达到100.4%;固定化漆酶的最适pH和最适温度较游离漆酶的均有升高且范围变宽,固定化后,漆酶的pH稳定性和热稳定性都得到显著提高;固定化漆酶的K m值略高于游离漆酶的;固定化漆酶具有良好的操作稳定性,与底物反应反复操作10批次后剩余酶活为72.7%。     

Adsorption and activity of lipase from Candida rugosa on the chitosan-modified poly(acrylonitrile-co-maleic acid) membrane surface

Efforts have recently been made to improve the biocompatibility of support surface for enzyme immobilization, which could create a specific microenvironment for the enzymes and thus benefit the enzyme activity. In this work, one natural macromolecule, chitosan, was tethered on the surface of poly(acrylonitrile-co-maleic acid) (PANCMA) membrane to prepare a dual-layer biomimetic support for enzyme immobilization. Lipase from Candida rugosa was immobilized on this dual-layer biomimetic support by adsorption. The properties of the immobilized enzyme were assayed and compared with those of the free one. It was found that the adsorption capacity of lipase on the chitosan-tethered PANCMA membrane increases with the decrease of ionic strength and there is an optimum pH value for the adsorption. The activity retention of the immobilized lipase on the chitosan-tethered membrane by adsorption (54.1%) is higher than that by chemical bonding (44.5%). In comparison with the immobilized lipase by chemical bonding, there is a decrease of the K(m) value and an increase of the V(max) value for the immobilized lipase by adsorption. Additionally, the experimental results of thermal stabilities indicate that the residual activity of the immobilized lipase at 50 degrees C is 38% by adsorption and 65% by chemical bonding.     

Direct introduction of amine groups into cellulosic paper for covalent immobilization of tyrosinase: support characterization and enzyme properties

Tyrosinase is used to eliminate phenolic compounds from wastewater. Therefore, its immobilization is important to enhance catalytic efficiency. Papery materials are of particular interest for use as support for enzyme immobilization since the porous microstructure of fiber networks in papers can provide a suitable reaction environment, especially in flow-type catalytic reactions. However, immobilization of protein onto papery structure needs chemical modifications in severe conditions. To overcome this challenge, a cellulosic paper was directly amine-functionalized in moderate conditions and used for tyrosinase immobilization. The support was pretreated with HCl (0.5 N) solution and then sequentially immersed in ethylenediamine (EDA), glutaraldehyde solution (2% v/v) and the crude enzyme. In comparison with the untreated one, the immobilized enzyme on the EDA-treated support offered a 3.7-fold increase in activity. The FTIR spectra as well as EDX analysis proved the presence of amine groups in the cellulosic paper and also covalent immobilization of tyrosinase on the modified support. When considering the effect of pH on the activity at 25 °C, a maximum relative activity of 134% at pH 6 was revealed. Similarly, evaluating the effect of temperature on the activity at pH 7 displayed a maximum relative activity of 152% at 35 °C. The immobilized enzyme was suitable for use for more than four cycles to degrade a phenolic compound at severe pH and temperature conditions. Additionally, the immobilized enzyme was active after treatment of the surface at different pHs and temperatures for 105 min. The chemically modified cellulosic paper can be used as a support for enzyme immobilization.     

聚乙烯亚胺改性聚丙烯腈中空膜固定脂肪酶

聚丙烯腈是富腈基的高分子聚合物,易修饰改性,广泛应用于膜分离应用.我们以聚丙烯腈中空膜为载体,采用化学法交联聚乙烯亚胺并固定脂肪酶,固定过程中引入海藻酸钠,用CaCl_2进行后处理,得到固定化脂肪酶PAN-PEI-SA/E-CaCl_2载酶量为31.70(mg enzyme)/(g support),酶活为50.20 U/(g support),15次重复使用可保留58.77%的酶活,与游离酶相比耐酸性和耐温性有所提高,相同条件下与Nov 435相比,酶活更高,这表明最终得到的固定化脂肪酶有良好的工业应用前景.     

Immobilization of Penicillin G Acylase on Calcined Layered Double Hydroxides

A hydrotalcite-like Mg2 /Al3 layered double hydroxide (LDH) material was prepared by means of amodified coprecipitation method involving a rapid mixing step followed by a separate aging process. LDH calcined at 500℃ , denoted as CLDH, was characterized by XRD, IR and BET surface area measurements.CLDH has a poor crystalline MgO-like structure with a high surface area and porosity. CLDH was used as asupport for the immobilization of penicillin G acylase(PGA). The effect of varying the immobilization conditions, such as pH, contact time and the ratio of enzyme to support, on the activity of the immobilized enzymein the hydrolysis of penicillin G has been studied. It was found that the activity of the immobilized enzyme decreased slightly with decreasing pH and reached a maximum after a contact time of 24 h. The activity of theimmobilized enzyme increased with increasing the ratio of enzyme to support. It was found that the adsorption of PGA inhibited the expected reaction of CLDH with an aqueous medium to regenerate a LDH phase. Itsoriginal activity(36%) after 15 cycles of reuse of the immobilized enzyme was retained, but no further loss in the activity was observed.     

纳米花型酶-无机杂化固定化酶研究进展

酶是一种绿色高效的生物催化剂,被广泛地应用于工业生产中,为了更好的提升游离酶的性能,酶固定化技术应运而生。然而,与游离酶相比,固定化酶活性下降以及传质受限一直是酶固定化技术亟待解决的关键问题。作为一种新型酶固定化技术,纳米花型酶-无机杂化固定化酶因具有高比表面积、高酶活性和高催化效率,且制备简单,绿色无污染受到广泛关注。本文综述了近年来纳米花型酶-无机杂化固定化酶的研究进展,根据纳米花型酶-无机杂化固定化酶的形成特点,将其分为单酶纳米花、双酶纳米花和负载型纳米花。阐述了纳米花型酶-无机杂化固定化酶的制备过程和形成机理并对纳米花型酶-无机杂化固定化酶在食品工业和检测领域的应用进展做出总结。最后,对纳米花型酶-无机杂化固定化酶的发展前景做出展望。     

Atomic force microscopy for the characterization of immobilized enzyme molecules on biosensor surfaces

The development of biosensors has been one of the key areas in biotechnology and biomedical studies. Often it is difficult to investigate the immobilized biomolecules on the surfaces for biosensor optimization. Atomic force microscopy (AFM) should provide an ideal means for the visualization of biosensor surface and for the investigation of biomolecule activities. Therefore, AFM has been employed to study the surface topography of immobilized glutamate dehydrogenase (GDH) on two-dimensional glutamate biosensor surfaces. Correlation between the surface topography and the activity of the biosensor was investigated. Surface analysis has revealed that the enzymatic activity of the immobilized GDH molecules on the biosensor surface is linked to surface roughness, as measured by the peak-to-valley distance. Fractal dimension of the immobilization sensor surface was found to be a good parameter for judging the quality of the immobilized biosensors. As enzyme immobilization time increases, the biosensor has its maximum activity with around 18 h of immobilization in 10^–6 M GDH solution. Various biosensors prepared under different experimental conditions have been studied by AFM. This technique is shown to be an effective tool to characterize biosensor surfaces.     

Atomic force microscopy for the characterization of immobilized enzyme molecules on biosensor surfaces

The development of biosensors has been one of the key areas in biotechnology and biomedical studies. Often it is difficult to investigate the immobilized biomolecules on the surfaces for biosensor optimization. Atomic force microscopy (AFM) should provide an ideal means for the visualization of biosensor surface and for the investigation of biomolecule activities. Therefore, AFM has been employed to study the surface topography of immobilized glutamate dehydrogenase (GDH) on two-dimensional glutamate biosensor surfaces. Correlation between the surface topography and the activity of the biosensor was investigated. Surface analysis has revealed that the enzymatic activity of the immobilized GDH molecules on the biosensor surface is linked to surface roughness, as measured by the peak-to-valley distance. Fractal dimension of the immobilization sensor surface was found to be a good parameter for judging the quality of the immobilized biosensors. As enzyme immobilization time increases, the biosensor has its maximum activity with around 18 h of immobilization in 10(-6) M GDH solution. Various biosensors prepared under different experimental conditions have been studied by AFM. This technique is shown to be an effective tool to characterize biosensor surfaces.     

Immobilization of the enzyme beta-lactamase on biotin-derivatized poly(L-lysine)-g-poly(ethylene glycol)-coated sensor chips: a study on oriented attachment and surface activity by enzyme kinetics and in situ optical sensing

Understanding the conformation, orientation, and specific activity of proteins bound to surfaces is crucial for the development and optimization of highly specific and sensitive biosensors. In this study, the very efficient enzyme beta-lactamase is used as a model protein. The wild-type form was genetically engineered by site-directed mutagenesis to introduce single cysteine residues on the surface of the enzyme. The cysteine thiol group is subsequently biotinylated with a dithiothreitol (DTT)-cleavable biotinylation reagent. beta-Lactamase is then immobilized site-specifically via the biotin group on neutral avidin-covered surfaces with the aim to control the orientation of the enzyme molecule at the surface and study its effect on enzymatic activity using Nitrocefin as the substrate. The DTT-cleavable spacer allows the release of the specifically bound enzyme from the surface. Immobilization of the enzyme is performed on a monolayer of the polycationic, biotinylated polymer PLL-g-PEG/PEG-biotin assembled on niobium oxide (Nb2O5) surfaces via neutral avidin as the docking site. Two different assembly protocols, the sequential adsorption of avidin and biotinylated beta-lactamase and the immobilization of preformed complexes of beta-lactamase and avidin, are compared in terms of immobilization efficiency. In situ optical waveguide lightmode spectroscopy and colorimetric analysis of enzymatic activity were used to distinguish between specific and unspecific enzyme adsorption, to sense quantitatively the amount of immobilized enzyme, and to determine Michaelis-Menten kinetics. All tested enzyme variants turned out to be active upon immobilization at the polymeric surface. However, the efficiency of immobilized enzymes relative to the soluble enzymes was reduced about sevenfold, mainly because of impaired substrate (Nitrocefin) diffusion or restricted accessibility of the active site. No significant effect of different enzyme orientations could be detected, probably because the enzymes were attached to the surface through long, flexible PEG chain linkers.     

固定化青霉素酰化酶新型载体PEI/SiO2的制备及其特性

通过γ-氯丙基三甲氧基硅烷的媒介, 将聚乙烯亚胺(PEI)化学偶联在硅胶微粒表面, 制备了固定化青霉素酰化酶的新型复合载体PEI/SiO2, 最终制得了活性高且稳定性好的固定化青霉素酰化酶. 通过测定复合载体表面PEI的偶合量, 考察了各种反应条件对复合载体制备的影响规律; 通过红外光谱与电导滴定法测定, 对复合载体表面的化学结构与组成进行了表征; 为探索复合载体PEI/SiO2固定化酶的作用机理, 测定了复合载体在固定化酶前的ζ电位. 研究结果表明, 通过氯丙基硅烷偶联剂的媒介, 聚胺大分子PEI可以充分地被化学偶联在SiO2表面, 键合量可达到15%. 偶联反应的适宜条件: 反应温度90-94 ℃; 反应时间5h; PEI的质量浓度0.45-0.50 g/mL. 由于PEI分子链中含有大量氨基, 少量的共价键联与大量的物理吸附相结合, 既可使青霉素酰化酶被快速稳定地固定化, 又能很好地保持酶的构象, 使其具有较高的催化活性与活力回收率, 而且具有良好的连续操作稳定性, 重复使用15次, 固定化酶的活性可稳定地保持在初活性的87.5%水平上.     

Electron paramagnetic resonance spin label titration: a novel method to investigate random and site-specific immobilization of enzymes onto polymeric membranes with different properties

The immobilization of biological molecules onto polymeric membranes to produce biofunctional membranes is used for selective catalysis, separation, analysis, and artificial organs. Normally, random immobilization of enzymes onto polymeric membranes leads to dramatic reduction in activity due to chemical reactions involved in enzyme immobilization, multiple-point binding, etc., and the extent of activity reduction is a function of membrane hydrophilicity (e.g. activity in cellulosic membrane?polysulfone membrane). We have used molecular biology to effect site-specific immobilization of enzymes in a manner that orients the active site away from the polymeric membrane surface, thus resulting in higher enzyme activity that approaches that in solution and in increased stability of the enzyme relative to the enzyme in solution. A prediction of this site-specific method of enzyme immobilization, which in this study with subtilisin and organophosphorus hydrolase consists of a fusion tag genetically added to these enzymes and subsequent immobilization via the anti-tag antibody and membrane-bound protein A, is that the active site conformation will more closely resemble that of the enzyme in solution than is the case for random immobilization. This hypothesis was confirmed using a new electron paramagnetic resonance (EPR) spin label active site titration method that determines the amount of spin label bound to the active site of the immobilized enzyme. This value nearly perfectly matched the enzyme activity, and the results suggested: (a) a spectroscopic method for measuring activity and thus the extent of active enzyme immobilization in membrane, which may have advantages in cases where optical methods can not be used due to light scattering interference; (b) higher spin label incorporation (and hence activity) in enzymes that had been site-specifically immobilized versus random immobilization; (c) higher spin label incorporation in enzymes immobilized onto hydrophilic bacterial cellulose membranes versus hydrophobic modified poly(ether)sulfone membranes. These results are discussed with reference to analysis and utilization of biofunctional membranes.     

Synthesis with Glutaraldehyde and Characterization of Uniformly Coated Alkaline Phosphatase-Nanoparticle Bioconjugates

Alkaline phosphatase from raw milk was immobilized on cysteine-functionalized silver nanoparticles with high efficiency. The nanoparticles were characterized by ultraviolet–visible spectroscopy, X-ray diffraction, and transmission electron microscopy. The surface functionalization was confirmed by infrared spectroscopy. The spherical nanoparticles were from 40 to 60?nm in size and used for the covalent immobilization of alkaline phosphatase on the surface with glutaraldehyde treatment. As compared to soluble enzyme, an enhanced enzymatic activity of 79.87% was obtained with a percentage immobilization of 75.41%. The immobilization process did not significantly affect the structure and size of the nanoparticles, while providing a uniform coating of the enzyme on the nanoparticle as characterized by electron microscopy. The bioconjugates were reusable for up to eight times with 85% retention of the initial enzymatic activity. The synthesis of these enzyme–nanoparticle bioconjugates with high activity and stability suggests their use in biological applications.     

Determination of active diaphorase immobilized at electrode surfaces

The activity of diaphorase (from Bacillus stearothermophilus) immobilized on glassy carbon (GC) electrodes was determined by analyzing the catalytic currents for oxidation of the immobilized enzyme using digital simulation techniques, which gives the concentration of the active enzyme at the electrode surface. Results show that the immobilization by the cross-linking reaction with glutaraldehyde deactivates the enzyme and only about 10% of the total enzyme remains active at the electrode surface.     

Activity of Candida rugosa lipase immobilized on gamma-Fe2O3 magnetic nanoparticles

We report the stability and enzymatic activity of Candida rugosa Lipase (E.C.3.1.1.3) immobilized on gamma-Fe2O3 magnetic nanoparticles. The immobilization strategies were either reacting the enzyme amine group with a nanoparticle surface acetyl, or amine groups. In the former, the enzyme was attached through a C=N bond, while in the latter it was connected using glutaraldehyde. AFM images show an average particle size of 20 +/- 10 nm after deconvolution. The enzymatic activity of the immobilized lipase was determined by following the ester cleavage of p-nitrophenol butyrate. The covalently immobilized enzyme was stabile and reactive over 30 days.     

Highly Efficient Method Towards In Situ Immobilization of Invertase Using Cryogelation

A novel method was developed for the immobilization of Saccharomyces cerevisiae invertase within supermacroporous polyacrylamide cryogel and was used to produce invert sugar. First, the cross-linking of invertase with soluble polyglutaraldehyde (PGA) was carried out prior to immobilization in order to increase the bulkiness of invertase and thus preventing the leakage of the cross-linked enzyme after immobilization by entrapment. And then, in situ immobilization of PGA cross-linked invertase within cryogel synthesis was achieved by free radical polymerization in semi-frozen state. The method resulted in 100 % immobilization and 74 % activity yields. The immobilized invertase retained all the initial activity for 30 days and 30 batch reactions. Immobilization had no effect on optimum temperature and it was 60 °C for both free and immobilized enzyme. However, optimum pH was affected upon immobilization. Optimum pH values for free and immobilized enzyme were 4.5 and 5.0, respectively. The immobilized enzyme was more stable than the free enzyme at high pH and temperatures. The kinetic parameters for free and immobilized invertase were also determined. The newly developed method is simple yet effective and could be used for the immobilization of some other enzymes and microorganisms.