射频激励等离子体非线性效应的FDTD数值模拟

在考虑热运动、电子复合、扩散等效应后，建立电磁波与等离子体相互作用模型，验证了射频激励等离子体时产生的二次、多次谐波以及各个不同频段信号的调制现象，得到了不同激励功率、产生电子的电场阈值、电子能量等参数对电磁波频谱的影响，这对于射频激励等离子体的电路匹配、耦合器件以及等离子体天线传输、电磁兼容等设计很有帮助. 关键词： 射频 谐波 等离子体 非线性     

等离子体用于腔体的雷达散射截面减缩的实验研究

利用荧光灯等离子体管覆盖金属腔体内壁,测量了筒状等离子体覆盖的金属腔体对电磁波的回波衰减。测试结果表明:金属圆筒内壁的等离子体能够有效吸收0.80~1.75 GHz波段的入射波,入射电磁波的回波衰减值为5~25 dB;当入射电磁波频率接近1.75 GHz时,回波衰减最为强烈,在入射角度为10°时,吸收峰值可达26.71 dB,因此选择合适的电磁波入射角度,能够使等离子体对微波的吸收达到峰值。理论分析了影响等离子体对电磁波衰减的主要因素。结果表明：等离子体可有效缩减腔体结构的雷达散射截面面积,因此在进气道等腔体结构的隐身方面具有一定的应用前景。     

不均匀等离子体中电磁波与Langmuir波的相互作用

通过理论研究与数值计算,不均匀等离子体中Langmuir波与电磁波的相互作用及其线性模式转换规律得到了充分的展示.导出了不均匀等离子体中的电磁色散关系,研究了入射电磁波或Langmuir波在通过不均匀等离子体的过程中发生转换的物理过程,以及波的传播矢量随空间坐标变化的关系,并对电磁波与Langmuir波相互作用的机理进行了讨论.研究结果对密度梯度所驱动的等离子体波产生电磁辐射的研究具有重要意义. 关键词： 电磁波 Langmuir波 不均匀等离子体 线性模式转换     

等离子体用于腔体的雷达散射截面减缩的实验研究

 利用荧光灯等离子体管覆盖金属腔体内壁,测量了筒状等离子体覆盖的金属腔体对电磁波的回波衰减。测试结果表明:金属圆筒内壁的等离子体能够有效吸收0.80~1.75 GHz波段的入射波,入射电磁波的回波衰减值为5~25 dB;当入射电磁波频率接近1.75 GHz时,回波衰减最为强烈,在入射角度为10°时,吸收峰值可达26.71 dB,因此选择合适的电磁波入射角度,能够使等离子体对微波的吸收达到峰值。理论分析了影响等离子体对电磁波衰减的主要因素。结果表明：等离子体可有效缩减腔体结构的雷达散射截面面积,因此在进气道等腔体结构的隐身方面具有一定的应用前景。     

真空环境中等离子体喷流对反射电磁波衰减的实验研究

在真空环境中，利用传输线测量装置，开展微波等离子体喷流对反射电磁波衰减的实验研究.实验结果表明，采用传输线测量方法能够有效地获得等离子体对反射电磁波的衰减；在5GHz附近，以氩气为工质，流量为52.5mg/s时，52W微波功率在真空环境中产生的等离子体喷流能对反射电磁波产生最大的衰减；增加微波功率、降低真空环境压强可以提高等离子体对反射电磁波的衰减；要使等离子体能够对反射电磁波产生最大的衰减，必须选取合适的发生器参数. 关键词： 电磁波在等离子体中的传输 等离子体基本过程 电磁波     

目标振动微多普勒效应教学实验的设计

设计了悬臂梁振动引起的微多普勒频移实验系统.采用10.525GHz的X波段雷达模块发射和接收电磁波,采用AD620放大雷达回波毫伏级信号,采用NI-6009数据采集模块与LabVIEW软件对回波信号采集、滤波、加窗和频谱分析,采用压电传感器验证雷达测频结果.实验结果表明:悬臂梁的有阻尼自由振荡对雷达波产生频率调制作用,其微多普勒频谱图由相邻间距为固有频率的谱线对构成.     

等离子体覆盖立方散射体目标雷达散射截面的时域有限差分法分析

采用分段线性电流密度递归卷积时域有限差分（PLJERC-FDTD）算法计算了均匀非磁化等离子体覆盖三维立方体目标的散射特性.分析了等离子体厚度、密度和碰撞频率对雷达散射截面（RCS）的影响.计算结果表明：等离子体包层能有效地减小雷达目标的RCS，当等离子体频率比入射电磁波频率小得多时，主要靠增大等离子体的厚度使立方散射体目标的RCS值减小，增大等离子体碰撞频率对立方散射体目标的RCS值影响不大；当等离子体频率约为入射电磁波频率的一半时，增大等离子体厚度和碰撞频率都对立方散射体目标的RCS值减小有影响；当等 关键词： FDTD算法 电磁波 等离子体隐身 雷达散射截面     

放电功率变化对电磁波在电感耦合闭式等离子体中的衰减特性

射频电感耦合等离子体(ICP)放电方式能够在较宽的压强范围内产生大面积、密度高的等离子体,在对电磁波衰减应用中具有较大优势。通过研究ICP等离子体与电磁波相互作用的过程,改进闭式等离子体模型,建立电磁波在非均匀等离子体中传播的分层计算模型,对实测诊断分布情形下等离子体与电磁波的相互作用进行研究,得到不同功率条件下电磁波衰减的变化情况;提出射频电感耦合闭式等离子体用于电磁波衰减的方法并实验验证,基于等离子体覆盖金属平板的测量模型,在实验室内搭建了以金属板为衬底的弓形微波反射测试系统,研究了闭式等离子体对4～8 GHz频段范围内微波反射的作用特性,以及不同射频功率对微波反射的影响规律,并将实验测量与计算结果进行对比分析。实验表明,通过功率调节,电感耦合闭式等离子体对5.92～6.8 GHz频带电磁波具有明显的衰减作用。     

电磁波在大气层人造等离子体中的衰减特性

利用洛沦兹模型来研究大气层人造非均匀等离子体的电磁响应特性,讨论了电磁波频率、等离子体密度及电子碰撞频率对电磁波衰减特性的影响.结果表明,电磁波在长波长区域及等离子体密度大时,其能量衰减越快.当等离子体密度高时,电子温度越低,大气层高度越高,电磁波的能量衰减越快. 关键词： 电磁波 大气等离子体 能量衰减     

高速模型尾迹流场及其电磁散射特性相似性实验研究

高速目标再入大气层或在临近空间飞行时,空气电离形成的等离子体鞘套和尾迹对目标的雷达散射特性会产生影响.为了研究不同模型尾迹流场及其电磁散射特性规律和相似性,以氧化铝球模型为研究对象,在弹道靶设备上开展了双尺度参数相同的条件下高速球模型尾迹流场及其电磁散射相似性实验研究.由二级轻气炮发射模型,模型直径分别为8.0、10.0、12.0、15.0 mm,速度约6 km/s,靶室压力分别为6.3,5.0,4.2,3.3 k Pa,采用阴影照相系统测量模型激波脱体距离、电子密度测量系统测量模型尾迹的电子密度分布、X波段单站雷达系统测量在视角为40?的模型及流场的雷达散射截面(RCS)分布.实验结果表明:在速度不变、双尺度参数相同的条件下,随着模型尺寸的增加,激波脱体距离逐渐增加,激波脱体距离与模型直径之比近似相同;不同模型尾迹电子密度测量曲线的趋势和数量级一致,表明不同模型的尾迹流场适用于双缩尺律;不同尺寸模型尾迹的总体RCS与分布RCS均不相同,表明不同模型尾迹的电磁散射不适用于二元缩尺律;高速球模型全目标电磁散射能量分布在模型及其绕流区域、等离子体尾迹区域;高速球模型全目标电磁散射能量在模型及绕流场区域出现1个强散射中心,在模型湍流尾迹区域出现多个散射中心;高速球模型尾迹的RCS测量信号呈现随机性分布特性,幅度脉动和频率脉动均没有周期性;随着模型尺寸的增加,模型尾迹的总体RCS增加,尾迹脉动频率的变化范围减小.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.