光纤基底TiNi形状记忆合金薄膜制备工艺

将TiNi基记忆合金薄膜与光纤相结合可制成智能化、集成化且成本经济的微机电系统和微传感器件.本文采用磁控溅射法在二氧化硅光纤基底上制备TiNi记忆合金薄膜,系统讨论了溅射工艺参数以及后续退火处理对薄膜质量的影响.采用自研制光纤镀膜掩膜装置在直径为125μm的光纤圆周表面上形成均匀薄膜.实验表明:在靶基距、背底真空度、Ar气流量和溅射时间一定的条件下,溅射功率存在最佳值;溅射压强较大时,薄膜沉积速率较低,但薄膜表面粗糙度较小.进行退火处理后,薄膜形成较良好的晶体结构,Ti_49.09Ni_50.91薄膜中马氏体B19′相和奥氏体B2相共存,但以B19′为主.根据本文研究结果,在玻璃光纤基底上制备高质量的TiNi基记忆合金薄膜是可实现的,本工作为下一步研制微机电系统和微型传感器做了基础准备.     

小角x射线散射确定TiNi薄膜中晶化粒子的长大激活能

用小角x射线散射技术研究以直流磁控溅射方法制备TiNi合金薄膜其退火生成的晶化粒子的长大行为.发现在室温下溅射的TiNi合金薄膜存在小于1nm尺寸的微空洞,将退火后薄膜的小角x射线散射强度扣除退火前微空洞产生的小角x射线散射强度,用这种方法得到的散射强度遵从Porod定律;而用通常方法扣除背底得到的散射强度结果不满足Porod定律.TiNi合金薄膜在733—793K之间退火晶化粒子的长大激活能Eg=301kJmol. 关键词： TiNi薄膜 晶化粒子 长大激活能     

退火温度和溅射时间对磁控溅射法制备Mg2Si薄膜的影响

采用磁控溅射法和原位退火工艺在钠钙玻璃衬底上制备 Mg2Si 薄膜。首先在钠钙玻璃衬底上交替溅射沉积两层Si、Mg 薄膜,冷却至室温后原位退火4 h,制备出一系列 Mg2Si 薄膜样品。通过 X 射线衍射仪(XRD) 、 扫描电子显微镜(SEM)对所得薄膜样品的晶体结构和表面形貌进行表征, 讨论了退火温度和溅射Si/Mg/Si/Mg 时间对制备 Mg2Si 薄膜的影响。结果表明,采用磁控溅射法在钠钙玻璃衬底上交替溅射两层Si、Mg 薄膜, 通过原位退火方式成功制备出单一相的 Mg2Si 薄膜,溅射Si/Mg/Si/Mg 的时间为12.5/9/12.5/9 min,退火温度为550 ℃ 时,制备的 Mg2Si 薄膜结晶度最好,连续性和致密性最强。这对后续 Mg2Si 薄膜器件的设计与制备提供了重要的参考。 积两层Si、Mg 薄膜, 冷却至室温后原位退火4 h, 制备出一系列 Mg2Si 薄膜样品. 通过 X 射线衍射仪(XRD) 、 扫描 电子显微镜(SEM)对所得薄膜样品的晶体结构和表面形貌进行表征, 讨论了退火温度和溅射Si/Mg/Si/Mg 时间 对制备 Mg2Si 薄膜的影响. 结果表明, 采用磁控溅射法在钠钙玻璃衬底上交替溅射两层Si、Mg 薄膜, 通过原位退火 方式成功制备出单一相的 Mg2Si 薄膜, 溅射Si/Mg/Si/Mg 的时间为12.5/9/12.5/9 min, 退火温度为550 ℃ 时, 制 备的 Mg2Si 薄膜结晶度最好, 连续性和致密性最强. 这对后续 Mg2Si 薄膜器件的设计与制备提供了重要的参考.     

周期性多层膜合金化制取的TiNi形状记忆薄膜的室温微结构特征

用掠入射X射线衍射及X射线反射对磁控溅射制取的等原子比Ni／Ti周期性多层膜晶化热处理 后的TiNi形状记忆薄膜室温微结构进行了研究.TiNi形状记忆薄膜在深度方向的相分布和元 素分布是不均匀的，都是一种多层结构.室温下其微结构特征为最外层是Ti氧化膜，再下层 是Ti₃Ni₄,B19’马氏体相和少量的B2奥氏体相的三相混合物，靠近 基体为主要相成分马氏体，最后是Ni和Si界面反应层.X射线反射率的拟和结果显示薄膜微结 构的分析是合理的.薄膜中相深度分布的不均匀性主要是动力学因素决定的. 关键词： 相深度分布 形状记忆 TiNi 多层膜     

利用表面磁光克尔效应监测Ni薄膜生长的物相转变

利用磁控溅射方法制备了不同厚度和退火处理的Ni薄膜.表面磁光克尔效应研究表明:冷基底无退火处理的Ni薄膜为软磁性,退火处理的Ni薄膜为铁磁性质,且无退火处理的Ni金属膜磁性随膜厚的增加而增强.分析认为,冷基底条件下Ni膜是非晶态生长,且膜内存有大量缺陷,经退火处理的Ni膜发生了重融再生长,形成了大颗粒结晶,膜内晶粒内缺陷大量消失.     

磁控溅射制备Y2O3-TiO2薄膜形貌的研究

室温下采用射频磁控溅射法,在硅衬底上制备了Y₂O₃-TiO₂氧化物复合薄膜.利用XRD(X-ray diffraction)和AFM( atomic force microscopy)分析观察了退火前后样品的物相、形貌等变化,讨论了致密薄膜的生长机理.实验发现,溅射功率越大,薄膜的平整度和致密度越好.对热处理前后样品的结晶结构和表面形貌的分析结果显示,在本实验参数范围内,随着溅射功率的增大,更多的Y₂O_{3关键词： 2}O₃-TiO₂薄膜')" href="#">Y₂O₃-TiO₂薄膜 表面形貌 原子力显微镜 磁控溅射     

溅射制备Ta2O5薄膜的表面形貌与光学特性

在室温条件下利用溅射Ta₂O₅靶材的方法制备了Ta₂O₅薄膜,并采用将薄膜两侧的反射率光谱进行比较的简便方法分析评估薄膜的光吸收,发现溅射制备薄膜的额外光吸收源是溅射引起的缺氧形成的,选择适当的溅射功率和含氧比例的工作气体能有效地消除这些缺陷、不用任何加温处理就可制备得到表面平坦和高致密度的高品质Ta₂O₅薄膜. 关键词： 2O₅薄膜')" href="#">Ta₂O₅薄膜 光吸收 表面形貌 磁控溅射     

磁控溅射功率对β-Ga2O3薄膜特性的影响

近年来,第三代宽禁带半导体材料β-Ga₂O₃受到越来越多的关注,在材料制备、掺杂、刻蚀等方面都有广泛研究.射频磁控溅射是常用的β-Ga₂O₃薄膜制备方法之一,而磁控溅射法制膜往往需要进行退火处理以提高薄膜质量.本文研究溅射功率对射频磁控溅射在C面蓝宝石基底上制备得到的β-Ga₂O₃薄膜特性的影响. X射线衍射(XRD)、原子力显微镜(AFM)和扫描电子显微镜(SEM)表征结果表明,随着溅射功率的增大,半峰宽呈现先增大后减小再增大的趋势,晶粒尺寸变化与之相反.此外,通过积分球式分光光度计,研究了溅射功率对β-Ga₂O₃薄膜光学特性的影响.光学特性方面,薄膜吸光度随着波长的增加,先升高后下降、再升高再下降,最后吸收边在700 nm附近截止,不同溅射功率制备的薄膜吸收光谱都存在两个吸收峰.     

高温氢退火还原V2O5制备二氧化钒薄膜及其性能的研究

过渡金属氧化物二氧化钒(VO₂)在温度340 K附近会发生金属绝缘体的转变(metal-insulator transition, MIT). 基于金属绝缘体的转变性质, VO₂薄膜材料具有很好的应用前景. 本文首先采用脉冲激光沉积制备了高质量的V₂O₅薄膜, 再通过高温氢退火还原V₂O₅薄膜制备出VO₂多晶薄膜. 研究了不同的退火温度、退火时间、退火气氛对VO₂薄膜制备的影响, 采用X射线衍射、X射线光电子能谱、变温电阻特性测量等手段对样品进行分析, 发现在H₂(5%)/Ar退火气氛下, 在一定的退火温度范围内(500–525 ℃), 退火 3 h, 得到了B相和M相共存的VO₂薄膜, 具有M相的VO₂的MIT特性, 而相同退火温度下退火时间达到4.5 h, 薄膜完全变成B相的VO₂. 通过纯Ar气氛下对B相VO₂再退火, 得到了转变温度为350 K, 电阻突变接近4个数量级的M相的VO₂薄膜. 实现了VO₂的B相和M相的相互转变. 关键词： 2薄膜')" href="#">VO₂薄膜 金属绝缘体转变 氢退火     

原位退火温度对Mg_2Si薄膜结构及方块电阻的影响

采用磁控溅射法和原位退火工艺在钠钙玻璃衬底上制备Mg_2Si半导体薄膜.首先在钠钙玻璃衬底上依次溅射一定厚度的Si、Mg薄膜,冷却至室温后原位退火4h,在400~600℃退火温度下制备出一系列Mg_2Si薄膜样品.采用X射线衍射仪(XRD)、扫描电子显微镜(SEM)对Mg_2Si薄膜样品的晶体结构和表面形貌进行表征,利用四探针测试仪测试薄膜样品的方块电阻,讨论了原位退火温度对Mg_2Si薄膜结构、表面形貌及电学性能的影响.结果表明,采用原位退火方式成功在钠钙玻璃衬底上制备出单一相的Mg_2Si薄膜,退火温度为550℃时,结晶度最好,连续性和致密性最强,方块电阻最小.这对后续Mg_2Si薄膜器件的设计与制备提供了重要的参考.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.