Determination of Tandospirone and its Impurities in Drug Formulations by LC-UV and LC-MS

This work describes the determination of tandospirone in bulk drug substance and formulated products by a reversed-phase liquid chromatographic method with UV detection. Chromatographic separation was performed on a C₁₈ column with a mobile phase of a binary mixture of methanol and water (70:30, v/v) delivered at a flow rate of 0.5 mL min^–1 and detection was performed at 243 nm. The proposed LC method is selective, precise and accurate for the determination of tandospirone in the presence of its manufacturing impurities with a limit of quantitation of 0.54 g mL^–1. A preliminary study for the identification of the major manufacturing impurities was made by liquid chromatography-mass spectrometry with electrospray ionization source operated in a positive ion mode.     

Study on the Melting Process of Nitrocellulose by Thermal Analysis Method

The melting process of NC is studied by using modulated differential scanning calorimetry (MDSC) technique, the microscope carrier method for measuring the melting point and the simultaneous device of the solid reaction cell in situ/RSFT-IR. The results show that the endothermic process in the MDSC curve is reversible. It is caused by the phase change from solid to liquid of the mixture of initial NC, decomposition partly into condensed phase products. The values of the melting point, melting enthalpy (H_m), melting entropy (S_m), the enthalpy of decomposition (H_dec) and the heat-temperature quotient (S_dec) obtained by the MDSC curve of NC at a heating rate of 10 K min^–1 are 476.84 K, 205.6 J g^–1, 0.4312 J g^–1 K^–1, –2475.0 J g^–1 and –5.242 Jg^–1K^–1, respectively. The MDSC results of NC with different nitrogen contents show that with increasing the nitrogen content in NC, the absolute values of H_m, S_m, H_dec and S_dec increase.This revised version was published online in November 2005 with corrections to the Cover Date.     

Development of an Improved Liquid Chromatographic Method for the Analysis of Doxycycline

Summary An improved LC method is described for the separation of doxycycline and its impurities. The separation of 2-acetyl-2-decarboxamidodoxycycline from the main peak doxycycline is much better than that obtained with official pharmacopoeia methods. The method is robust and shows good selectivity, repeatability, linearity and sensitivity. Eight commercial samples were examined using the method developed. The method uses an XTerra RP-18, 5 m (25 cm × 4.6 mm I. D.) column kept at a temperature of 35 °C. UV detection is performed at 280 nm. The mobile phase consists of acetonitrile – 0.2 M tetrabutylammonium hydrogen sulphate pH 7.0 – 0.3 M ethylenediaminetetraacetate pH 7.0 – water (130:350:350:170, v/v/v/v).     

Synthesis and Application of a Novel Poly(Acryl-p-Toluenesulfonamideamidine-p-Toluenesulfonylamide) Chelating Fiber for Preconcentration and Separation of Trace Noble Metal Ions from Solution Samples

A novel poly(acryl-p-toluenesulfonamideamidine-p-toluenesulfonylamide) chelating fiber containing S, N and O elements was synthesized from polyacrylonitrile fiber and p-toluenesulfonamide and used for the preconcentration and separation for traces of Ru(III), Rh(III), Au(III) and Pd(IV) ions from waste water and ore sample solution. The synthesis of this fiber was simple and rapid. The results indicate that 100ngmL^–1 of these ions can be quantitatively enriched by the chelating fiber at a flow rate of 6mLmin^–1 and a pH of 4 and desorbed quantitatively with 20mL of 6molL^–1 HCl and 5% CS(NH₂)₂ solution at 50°C (with recovery>95%). A 50 to 1000-fold excess of Ca²⁺, Mg²⁺, Mn²⁺, Co²⁺, Fe³⁺, Cu²⁺, Zn²⁺, and Al³⁺ ions caused little interference in the concentration and determination of the analyzed ions. When the fiber had been reused twenty times, the recoveries of the ions enriched by the fiber were still over 96%. The saturated adsorption capacities of the fiber were in the range of 22–96mgg^–1. The relative standard deviation (RSD) of the method was between 0.70% and 0.84%. Recoveries of a standard added to actual samples were in range of 95–101%. The results obtained for these ions in real solution samples were basically in agreement with the given values, the average errors being below 5.0%. FT-IR spectra show that the existence of –SO₂–Ar, HN=C–NH–, O=C–NH– and –NH–SO₂ functional groups are verified in the chelating fiber. The experiments show that the method is rapid, precise, simple and convenient.     

Thermochemistry of Amines: Experimental Standard Molar Enthalpies of Formation of N-Alkylated Piperidines

The standard molar enthalpies of formation _f H _m ^° (l) at the temperature T = 298.15 K were determined using combustion calorimetry for N-methylpiperidine (A), N-ethylpiperidine (B), N-propylpiperidine (C), N-butylpiperidine (D), N-cyclopentylpiperidine (E), N-cyclohexylpiperidine (F), and N-phenylpiperidine (G). The standard molar enthalpies of vaporization _l ^g H ^{m °} of these compounds were obtained from the temperature variation of the vapor pressure measured in a flow system. From these data the following standard molar enthalpies of formation in gaseous phase _f H _m ^° (g) were derived for: A –(61.39 ± 0.88); B –(88.1 ± 1.3); C –(105.81 ± 0.66); D –(126.2 ± 1.3); E ( –88.21 ± 0.75); F –(135.21 ± 0.94); G (70.3 ± 1.4) kJ · mol^–1. They are used to determine the strain enthalpies of the cyclic amines A–G. The N-alkylated piperidine rings have been found to be about strainless.     

Crystal Structures of Two New Holmium Polysulfides in the Series of Rare-Earth Polychalcogenides

The crystal structures of two polysulfide phases HoS_1.885(5) (I) and HoS_1.863(8) (II) were determined; the integer stoichiometric ratio was found to be Ho₈S₁₅. The data were collected on an Enraf-Nonius CAD-4 automatic diffractometer using the standard procedure (MoK, graphite monochromator, an absorption correction applied based on -scan data). Crystal I: space group P4/nmm, a = 3.820(1), c = 7.840(3) , V = 114.40(6) ³, Z = 2 for the composition HoS_1.885(5), d _calc = 6.542 g/cm³, R = 0.0520 for 184 unique reflections with I_hkl > 2 _I; crystal II: space group P2₁/m, a = 10.961(2), b = 11.465(2), c = 10.984(2) , = 91.27(3)°, V = 1380.0(4) ³, Z = 24 for the composition HoS_1.863(8), d _calc = 6.486 g/cm³, R = 0.0596 for 5354 unique reflections with I_hkl > 2 _I. In both compounds, the Ho atoms are surrounded by 9 (8+1 for three atoms in II) S atoms forming monocapped square antiprisms. The Ho–S distances vary from 2.717 to 3.067 irrespective of the type of ion [S^2– or (S₂)^2–]; the maximal distance to the atoms completing the coordination is 3.684 . The compounds have PbFCl type structures composed of ...(S₂)^2–...Ho³⁺...S^2–...S^2–...Ho³⁺...(S₂)^2–... layer packets differently oriented in space relative to the unit cell axes. The S^2–...S^2– and S^2–...(S₂)^2– interlayer distances are mostly shorter than the sum of the ionic radii and vary within the limits of 3.331-3.558 and 3.029-3.784 for the first and second types, respectively. For I, the calculated site occupancies and densities are given depending on the composition Ho-S_2-x (x = 0.25-0); for II, the most probable formulas of rational compositions in the same range of x are presented.     

Spectrophotometric determination of rhenium using 2-pyridyl thiourea

The reagent 2-pyridyl thiourea produces a reddish brown complex with rhenium in hydrochloric acid medium in the presence of tin(II) chloride. The complex shows absorption maxima at 405 nm, obeys Beer's law for a range of 1–16 ppm of rhenium. The sensitivity and molar absorptivity is found to be 0.0115g cm^–2 and 1.603×10⁴ 1 mol^–1 cm^–1 respectively showing an improvement over other sulphur-nitrogen bearing ligands. Composition found by Job's and mole ratio method, indicates that the complex contains metal and reagent in the ratio 12. Stability constant and stepwise formation constants of the complex have been evaluated by Harvey-Manning's method (logK _overall=8.825), Leden's method (logK _overall=8.3096), Rossotti-Rossotti's method (logK _overall=8.653) and Yatsimirskii's method (logK _overall=8.740). The relative error per 1% absolute photometric error is found to be 2.7%.     

Aquation of α-cis-chloroaquoethylenediamine-N,N'-diacetatocobalt(III) in aqueous and in mixed solvents: A mechanistic study

Summary The displacement of chloride ligands from -cis-chloro-aquoethylenediamine-N,N-diacetatocobalt(III) in nonacidic aqueous solutions was followed conductimetrically at 30–45° and the products of aquation were characterised by conductance, spectral and ion-exchange techniques. The rate constants for aquation in aqueous media and in 1 : 4 v : v mixed solvents at 25° are: 4.0 × 10^–5 s^–1 in H₂O, 2.71 × 10^–5 s^–1 in MeOH : H₂O, 2.74 × 10^–5 s^–1 in EtOH: H₂,O and 2.58 × 10^–5 s^–1 n in Me₂CO : H₂O. The corresponding H* and S* values have also been evaluated. Solvent polarity has a marked influence on the rate of chloride ion release. The aquation rate constants and the activation parameters have been correlated with solvent parameters,e.g. D, Y-values, Dimroth's E_T and Kosower's Z-values and, based on these correlations, a dissociative interchange (I_d) mechanism is proposed rather than dissociative as observed for some other cobalt(III) complexes.Senior author.     

Determination of Lercanidipine Hydrochloride and Its Impurities in Tablets

The reversed-phase high-performance liquid chromatography (RP-HPLC) method was developed for determination of lercanidipine hydrochloride and its synthetic impurities, degradation and oxidative products in Carmen^® tablets. The best separation was performed on Zorbax SB C18 column, 250 x 4.6 mm, particle size 5 m. Acetonitrile-water-triethylamine 55:44.8:0.2 (v/v/v) was used as a mobile phase with flow rate 1 mL min^–1. pH was adjusted to 3.0 with orthophosphoric acid. UV detection was performed at 240 nm. Duration of chromatographic run was about 12 min for six examined compounds. The chromatographic conditions for the determination of lercanidipine hydrochloride and its related substances were the same, but the concentration of lercanidipine hydrochloride was 0.03 mg mL^–1 for assay and 0.3 mg mL^–1 for related substances. The validation of the method performance characteristics (figures of merits, quality of parameters) was established to be adequate for the intended use. The evaluation of number of parameters, such as selectivity, linearity, accuracy, specificity, precision (repetability and reproducibility), sensitivity and detection and determination limits is entailed.Acknowledgements This work was supported by the Institute of Pharmacy of Serbia, Belgrade and by the Ministry for Science, Technology and Development of Serbia, Contact: 1458     

Spectrophotometric determination of mercury with 5,10,15,20-tetrakis(3-chloro-4-sulfophenyl)porphine by flow injection analysis

5,10,15,20-tetrakis(3-chloro-4-sulfophenyl)porphine (m-Cl-TPPS₄) was synthesized and used for the Spectrophotometric determination of mercury by flow injection analysis. A pseudo-first-order reaction kinetic mechanism was proposed with a rate constant of 0.8 min^–1 for Hg(II) withm-Cl-TPPS₄ in the presence of 8-hydroxyquinoline in a medium of 1.0M acetic acid and sodium acetate buffer solution (pH 6.22). In the optimum conditions of reaction temperature (85 ° C), stopped-flow time (60 s) and sampling volume (100 l), the method's relative standard deviation was 0.82% (n = 12) at 5.0 g ml^–1 mercury, with a linear range of 0–12.0 g ml^–1 and an analytical frequency of 60h^–1. The detection limit (3) was 0.025 g ml^–1. Interference studies showed that most metal ions co-existing with Hg²⁺ could be tolerated at 100-fold excess levels, but Zn²⁺, Cu²⁺ and Mn²⁺ needed to be masked. The method has been applied to the analysis of water samples with satisfactory results.     

LC-APCI-MS-MS methodology for determination of glybenclamide in human plasma

A liquid chromatographic/atmospheric pressure chemical ionization tandem mass spectrometric method (LC-APCI-MS-MS) for the determination of glybenclamide in human plasma is described. Glypizide, an analogue of glybenclamide, was used as internal standard. The analyte was extracted from plasma with diethyl ether/dichloromethane (70:30 v/v). The chromatography uses C₁₈ and 0.01 mol L^–1 acetic acid/acetonitrile (20:80 v/v) as stationary and mobile phase, respectively. Quantitation was preformed by using multiple reaction monitoring (MRM) of the precursor ion (m/z 494.2368.8) and the related product ion (m/z 446.0347.3) using the internal standard method. The analytical curve was linear in the range 1–300 ng mL^–1, and for a 400-L sample of human plasma, the limit of determination of the method was 1 ng mL^–1. The coefficients of variation of the method for intra-assay (within-run precision) and inter-assay (between-run precision) were less than 10%. The method was shown to be suitable for pharmacokinetic studies.An erratum to this article can be found at     

Heat capacities of aqueous perchloric acid and sodium perchlorate at 298°K: ΔC p o of ionization of water

We have used a Picker flow calorimeter for measurements leading to apparent molal heat capacities of dilute aqueous solutions of HClO₄ and NaClO₄ at 298°K. Results have been used to derive _c ^° =–27.1J-°K ^–1-mole ^–1 for HClO₄ (aq.), _c ^° =15.2J-°K ^–1-mole ^–1 for NaClO₄ (aq.), and C _p=–213.₈J-°K^–1-mole^–1 for ionization of water.     

The CO2 Reforming of Natural Gas in a Pulsed Corona Discharge Reactor

The conversion of CO ₂ and (CH ₄+CO ₂ ) mixtures to CO, at room temperature and atmospheric pressure conditions, in pulsed corona discharges, was investigated. Conversion of pure CO ₂ was 16.8% at 10 cm ³ -min ^–1 flow rate, which corresponds to 75 mol-min ^–1 rate of conversion. The CO ₂ conversion was improved to 38% (85 mol-min ^–1 by feeding the reactor with CH ₄+CO ₂ gas mixture (1:1 ratio), simultaneously with CH ₄ conversion of 46% (102.7 mol-min ^–1 ) at 10 cm ³ -min ^–1 flow rate of feed gases and 9 W power conditions. Rate of CO production is increased from 110 to 180 mol-min ^–1 with the variation of feed gas (CH ₄+CO ₂ mixture, 1:1 ratio) flow rate from 10 to 40 cm ³ -min ^–1 at 9W, which corresponds to energy efficiency of 2.5 to 4.1%. Highest energy yield of 25 g/kWh for CH ₄ conversion, 29 g/kWh for CO ₂ conversion, and 33 g/kWh for CO production were achieved.     

Untersuchungen im System Hafnium-Tantal-Kohlenstoff

Zusammenfassung Der Aufbau des Dreistoffes: Hf–Ta–C wird für 1850°C mittels druckgesinterter und vakuum-geglühter Proben bestimmt. Die lückenlose Mischbarkeit der Monocarbide wird erneut bestätigt. Ta₂C löst etwas mehr als 10 Mol% Hafniumcarbid. Die -Phase (Ta₃C₂) wird bereits bei geringen Hf-Konzentrationen unterdrückt. Das Dreiphasenfeld: (Hf, Ta)-Mischkristall+(Hf, Ta)C_1-x+(Ta, Hf)₂C charakterisiert den Schnitt. Hafnium reichert sich in der Carbidphase an. Die Gleichgewichte werden unter vereinfachenden Annahmen thermodynamisch ausgewertet und folgende Differenzen für freie Bildungsenergien (1850°C) errechnet: G _HfC–G _TaC=–8500 cal/Mol, G(_Hf2_C)—G _{Ta 2}C=–5000 cal/Mol. Ein zu Ta₂C analoges Hafniumcarbid (Hf₂C) ist jedoch um 10 000 cal/Mol weniger stabil als ein Gemenge: HfC_1–x+Hafnium. Es besteht gute Übereinstimmung zwischen den gerechneten und den experimentell ermittelten Konoden. Aussagen über das verwandte System: Hf–Nb–C werden gemacht.Mit 5 Abbildungen     

Coordination compounds of copper(II), nickel(II), and cobalt(II) with β-thiosemicarbazones of isatin and <Emphasis Type="Italic">N</Emphasis>-methylisatin

Isatin thiosemicarbazone (HL) reacts in aquoeus-ethanolic medium with copper(II) chloride and bromide (pH 7–7.5, ethanolic KOH) to give coordination compounds CuLXnH₂O (X = Cl, Br; n = 3, 4). In the presence of amines (A = C₅H₅N, 3-CH₃C₅H₄N, and 4-CH₃C₅H₄N), complexes CuALX2H₂O and CuA₂LXH₂O (X = Cl, Br) are formed. With nickel(II) or cobalt(II) chlorides, thiosemicarbazone HL, and pyridine (1:1:3) as starting compounds, compounds MPy₂LClH₂O (M = Ni, Co) are isolated. Under similar conditions, N-methylisatin -thiosemicarbazone (HL) reacts with chlorides of the above-noted metals in the presence of pyridine to give complexes MPy₂LClH₂O (M = Cu, Ni, Co). All the complexes are monomeric and have a pseudooctahedral structure of the coordination unit. Thiosemicarbazones HL and HL in these complexes behave as tridentate monodeprotonated O,N,S-ligands. Thermolysis of these substances passes through the stages of dehydration (60–90°C), deaquation (135–140°C) or deamination (160–215°C), and complete thermal decomposition (560–670°C).Translated from Zhurnal Obshchei Khimii, Vol. 74, No. 9, 2004, pp. 1539–1543.Original Russian Text Copyright © 2004 by Samus, Tsapkov, Gulya.This revised version was published online in April 2005 with a corrected cover date.     

Microdialysis sampling and high-performance liquid chromatography with chemiluminescence detection for in-vivo on-line determination and study of the pharmacokinetics of levodopa in blood

A simple, reliable, and reproducible method for in-vivo on-line separation and determination of levodopa has been based on microdialysis then high-performance liquid chromatography with chemiluminescence detection. The perfusate is perfused at a flow rate of 5 L min^–1. The concentration of levodopa in the dialysate is determined on line with a chemiluminescence system. The dialysate sample volume is approximately 20 L. The response of the system is linearly related to the concentration of levodopa in the range 1×10^–8 to 1×10^–6 g mL^–1 (r²=0.9995) with a detection limit (3) of 3×10^–9 g mL^–1 and sample throughput of 12 h^–1; RSD is 2.8% (n=11). The method has been successfully used to study the pharmacokinetics of levodopa in vivo; the values of the pharmacokinetics parameters C_max, AUC_0–t and T_max were 16.60, 20.92 ng mL^–1, and 90 min, respectively.     

LC Method for the Determination of Multiple Components in a Compound Cold Formulation

An isocratic liquid chromatographic method for determination of acetaminophen (AMP), caffeine (CAF), chlorphenamine maleate (CPM) and guaiacol glyceryl ether (GGE) in a compound cold formulation is described. Separation and quantitation were achieved on a Diamonsil C18 column using a binary mixture of methanol and 1.5% aqueous acetic acid (55: 45, v/v, pH 3.6) as mobile phase delivered at 0.4 mL min^–1. Single wavelength detection was at 220 nm for all four drugs and the run time was < 10 min. The linearity, accuracy and precision of the method were found to be acceptable over the concentration ranges: 16.0–127.8 g mL^–1 for AMP, 6.0–48.2 g mL^–1 for CAF, 5.0–40.0 g mL^–1 for CPM and 10.1–80.6 g mL^–1 for GGE.     

Rapid and sensitive method for the determination of acetaldehyde in fuel ethanol by high-performance liquid chromatography with UV–Vis detection

A high-performance liquid chromatography (HPLC) method for the determination of acetaldehyde in fuel ethanol was developed. Acetaldehyde was derivatized with 0.900 mL 2,4-dinitrophenylhydrazine (DNPHi) reagent and 50 L phosphoric acid 1 mol L^–1 at a controlled room temperature of 15°C for 20 min. The separation of acetaldehyde-DNPH (ADNPH) was carried out on a Shimadzu Shim-pack C₁₈ column, using methanol/LiCl_(aq) 1.0 mM (80/20, v/v) as a mobile phase under isocratic elution and UV–Vis detection at 365 nm. The standard curve of ADNPH was linear in the range 3–300 mg L^–1 per injection (20 L) and the limit of detection (LOD) for acetaldehyde was 2.03 g L^–1, with a correlation coefficient greater than 0.999 and a precision (relative standard deviation, RSD) of 5.6% (n=5). Recovery studies were performed by fortifying fuel samples with acetaldehyde at various concentrations and the results were in the range 98.7–102%, with a coefficient of variation (CV) from 0.2% to 7.2%. Several fuel samples collected from various gas stations were analyzed and the method was successfully applied to the analysis of acetaldehyde in fuel ethanol samples.     

A new route to the asymmetric Schiff base ligands. The ligand exchange in [Mo(CN)<Subscript>3</Subscript>O(salhy)]<Superscript>2−</Superscript> ion. Kinetics and mechanism

The kinetics of the ligand exchange in (PPh₄)₂[Mo(CN)₃O(salhy)]. 6H₂O (Hsalhy = salicylaldehyde hydrazone) by a solvent molecule and by 2,2-bipyridine (bpy) have been studied in EtOH. For the ligand exchange by a solvent molecule the pseudo-first order rate constant equals k _obs = 3.2 (±0.2) × 10^–3 s^–1 (t=25 °C), H =67 (± 7) kJ mol^–1, S =–75 (±23) J mol^–1 K^–1, while for the exchange by a bpy molecule k _obs=3.5 (±0.2) × 10^–3 s^–1 (t=25 °C), H =56 (±7) KJ mol^–1, S = –104 (±8) J mol^–1 K^–1. It was found, that all reactions proceed via the same mechanism which involves the chelate ring opening cis to the Mo=O bond. The mechanism of the reaction was proposed and was proved by the synthesis of (PPh₄)₂[Mo(CN)₃O(N-pic)]. 2.5H₂O (N-pic denotes that the nitrogen of picolinic acid is trans to Mo=O) by ligand exchange in EtOH, while in aqueous solution the O-pic analogue is formed exclusively.     

Analysis of wheat extracts for ochratoxin A by molecularly imprinted solid-phase extraction and pulsed elution

A molecularly imprinted solid-phase extraction (MISPE) method has been developed for the rapid analysis of wheat extracts for ochratoxin A (OTA). Molecularly imprinted polymer (MIP) particles were synthesized from N-phenylacrylamide (PAM) and slurry-packed into a micro-column for selective solid-phase extraction (SPE) of OTA. With water flowing at 0.5 mL min^–1, a total binding capacity of 30 ng OTA was determined for the 20 mg of MIP particles. MISPE conditions were optimized using OTA in methanol/acetic acid (99:1 v/v). Nearly 100% binding could be achieved from one 20-L injection of sample containing up to 30 ng of OTA. Pulsed elution (PE) using methanol/triethylamine (99:1 v/v) was good for the quantitative desorption of OTA. The MISPE–PE method, with fluorescence detection at _ex=385 nm and _em=445 nm, afforded a detection limit of 5.0 ng mL^–1 (or 0.1 ng in 20 L of sample injected) for OTA. Recovery of OTA from wheat extracts was 103±3%. Each MISPE–PE analysis required less than 5 min to complete.