Adsorption of UO2 2+ from aqueous solution onto copolymers of styrene and maleic anhydride

The copolymers of styrene and maleic anhydride resin (PSt/MA) was synthesized by free radical polymerization and characterized by means of FTIR. It is shown that the PSt/MA copolymer has rather strong coordination ability to UO₂ ²⁺ ions by chelation with the carboxylate group, and the microstructures of the U(VI)-PSt/MA complexes can be well controlled. The influence factors on UO₂ ²⁺ ions were also investigated and described in detail, such as contact time, solid/liquid ratio, pH value, ethanol content, and initial concentration. It was found that the maximum adsorption quantity of UO₂ ²⁺ was 831 mg/g. Experiments show that PSt/MA can recover UO₂ ²⁺ ions with high adsorption selectively from a simulated industry solution containing Ca²⁺ and Mg²⁺ as impurities. The adsorption kinetic data were best described by the pseudo-second-order equation, indicating that the chemical adsorption was the rate-limiting step. And there are very good correlation coefficients of linearized equations for Langmuir model, which indicated that the sorption isotherm of the PSt/MA for UO₂ ²⁺ can be fitted to the Langmuir model. After five times of repeated tests for the hydrogel it still remained its excellent adsorption.     

Removal of U(VI) from aqueous solutions by using MWCNTs and chitosan modified MWCNTs

In this paper, the multiwalled carbon nanotubes (MWCNTs) were modified with chitosan (CS) by using low temperature plasma grafting technique (denoted as MWCNT-CS). The prepared MWCNTs and MWCNT-CS were characterized by SEM, TEM, FTIR and Raman spectroscopy in detail and the results suggested that CS molecules were successfully grafted on the surfaces of MWCNTs. The materials were applied as adsorbents in the removal of U(VI) ions from large volumes of aqueous solutions as a function of environmental conditions. The removal of U(VI) from aqueous solution to MWCNTs and MWCNT-CS increased with increasing pH values at pH < 7, and then decreased with increasing pH values at pH > 7. The sorption of U(VI) on MWCNTs and MWCNT-CS was strongly dependent on pH and independent of ionic strength. The sorption of U(VI) on MWCNTs and MWCNT-CS was dominated by inner-sphere surface complexation rather than by ion exchange or outer-sphere surface complexation. The surface grafted chitosan molecules can enhances U(VI) sorption on MWCNTs obviously, which was also evidenced from the XPS spectroscopy analysis. The results of high sorption capacity of U(VI) on MWCNT-CS suggest that the MWCNT-CS nanomaterial is a suitable candidate in the preconcentration of U(VI) ions from large volumes of aqueous solutions.     

Removal of Cu2+ from aqueous solution by chitosan-coated magnetic nanoparticles modified with alpha-ketoglutaric acid

Chitosan-coated magnetic nanoparticles (CCMNPs), modified with a biodegradable and eco-friendly biologic reagent, alpha-ketoglutaric acid (alpha-KA), was used as a magnetic nanoadsorbent to remove toxic Cu(2+) ions from aqueous solution. The prepared magnetic nanoadsorbents were characterized by FTIR, TEM, VSM, XRD, and EDS. Factors influencing the adsorption of Cu(2+), e.g., initial metal concentration, initial pH, contact time and adsorbent concentration were investigated. TEM images show that the dimension of multidispersed circular particles is about 30 nm and no marked aggregation occurs. VSM patterns indicate superparamagnetic properties of magnetic nanoadsorbents. EDS pictures confirm the presence of the Cu(2+) on the surface of magnetic nanoadsorbents. Equilibrium studies show that Cu(2+) adsorption data follow Langmuir model. The maximum adsorption capacity (q(max)) for Cu(2+) ions was estimated to be 96.15 mg/g, which was higher than that of pure CCMNPs. The desorption data show no significant desorption hysteresis occurred. In addition, the high stability and recovery capacity of the chitosan-coated magnetic nanoparticles modified with alpha-ketoglutaric acid (alpha-KA-CCMNPs) suggest that these novel magnetic nanoadsorbents have potential applications for removing Cu(2+) from wastewater.     

Structure of the UO2 2+-SO 4 2- ion pair in aqueous solution

The structure of the ion pairs formed in aqueous uranyl sulfate solutions has been investigated with high-energy X-ray scattering. Sulfate binds to the uranyl as a monodentate ligand in equimolar solutions. The geometry of the ion pair is very similar to configurations found in crystalline structures; in particular, the U-O-S angle is bent in solution as well as in the solid state. It can therefore be concluded that an U-O-S angle of 143 degrees is an intrinsic property of the uranyl sulfate bond and not due to packing effects or interaction with the water in the primary solvation shell.     

Removal of radiocobalt from aqueous solution by oxidized MWCNT

The study was undertaken to evaluate the feasibility of oxidized multiwalled carbon nanotube (oxidized MWCNT) for the removal of radiocobalt (⁶⁰Co) from aqueous solutions. The oxygen functional groups of oxidized MWCNT were characterized by FT-IR and XPS. Batch experiments were performed to study the sorption of cobalt as a function of contact time, solid contents, pH, ionic strength, foreign ions, and temperature. Two kinetic models viz. pseudo-first-order and pseudo-second-order were used to determine kinetic sorption parameters, and the kinetic sorption could be described more favorably by the pseudo-second-order model. The thermodynamic parameters (∆G°, ∆S°, ∆H°) calculated from the temperature-dependent sorption isotherms indicated that the sorption of Co(II) on oxidized MWCNT was an endothermic and spontaneous processes. The results suggest that oxidized MWCNT can be used efficiently in the treatment of industrial effluents containing radioactive and heavy metal ions.     

Removal of methyl violet from aqueous solution by perlite

The use of perlite for the removal of methyl violet from aqueous solutions at different concentration, pH, and temperature has been investigated. Adsorption equilibrium is reached within 1 h. The capacity of perlite samples for the adsorption of methyl violet was found to increase with increasing pH and temperature and decrease with expansion and increasing acid-activation. The adsorption isotherms are described by means of the Langmuir and Freundlich isotherms. The adsorption isotherm was measured experimentally at different conditions and the experimental data were correlated reasonably well by the adsorption isotherm of Langmuir. The order of heat of adsorption corresponds to a physical reaction. It is concluded that the methyl violet is physically adsorbed onto the perlite. The removal efficiency (P) and dimensionless separation factor (R) have shown that perlite can be used for removal of methyl violet from aqueous solutions, but unexpanded perlite is more effective.     

Oxidation of UO2(s) in aqueous solution

In this review the kinetics and mechanism of oxidative dissolution of UO₂(s), mainly under conditions of relevance for the safety assessment of a deep geological repository for spent nuclear fuel, are discussed. Rate constants for the elementary processes involved (oxidation of UO₂ and dissolution of oxidized UO₂) are used to calculate the rates of oxidative UO₂(s) dissolution under various conditions (type of oxidant, oxidant concentration and HCO₃ ⁻/CO₃ ²⁻ concentration) for which experimental data are also available. The calculated rates are compared to the corresponding experimental values under the assumption that the experimental numbers reflect the steady-state conditions of the system. The agreement between the calculated rates and the corresponding experimental ones is very good, in particular for the higher rates. In general, the calculated rates are somewhat higher than the experimental numbers. This can be due partly to the use of initial concentrations rather than steady-state concentrations in the calculations. The kinetic data are also used to quantitatively discuss the dynamics of spent nuclear fuel dissolution under deep geological repository conditions.      

Removal of radiocobalt from aqueous solution by Mg2Al layered double hydroxide

The adsorption behavior of radiocobalt by Mg₂Al layered double hydroxide (Mg₂Al LDH) was studied as a function of contact time, pH, ionic strength, foreign ions, FA and temperature under ambient conditions. The results showed that the kinetic adsorption could be described by a pseudo-second order model very well. The adsorption of Co(II) on Mg₂Al LDH was strongly dependent on pH and ionic strength. The presence of FA enhanced the adsorption of Co(II) on Mg₂Al LDH at low pH, whereas reduced Co(II) adsorption at high pH. The Langmuir model fitted the adsorption isotherms of Co(II) better than the Freundlich and D–R model at three different temperatures of 303, 323 and 343 K. The thermodynamic parameters (ΔH°, ΔS° and ΔG°) calculated from the temperature dependent adsorption isotherms indicated that the adsorption process of Co(II) on Mg₂Al LDH was endothermic and spontaneous. The results show that Mg₂Al LDH is a promising material for the preconcentration and separation of pollutants from large volumes of aqueous solutions.     

Removal of methylene blue from aqueous solution by graphene oxide

Graphene oxide (GO) is a highly effective absorbent of methylene blue (MB) and can be used to remove MB from aqueous solution. A huge absorption capacity of 714 mg/g is observed. At initial MB concentrations lower than 250 mg/L, the removal efficiency is higher than 99% and the solution can be decolorized to nearly colorless. The removal process is fast and more efficient at lower temperatures and higher pH values. The increase of ionic strength and the presence of dissolved organic matter would further enhance the removal process when MB concentration is high. The results indicate that GO can be applied in treating industrial effluent and contaminated natural water. The implications to graphene-based environmental technologies are discussed.     

Removal of phosphate from aqueous solution by zeolite synthesized from fly ash

Fifteen Chinese fly ashes were converted hydrothermally into zeolites, and phosphate immobilization capacity (PIC) of the synthesized zeolites and the corresponding raw fly ashes were determined using an initial phosphate concentration of 1000 mg/L. Results showed that there was a remarkable increase in PIC (from 1.2 to 7.6 times) following the synthesis process. Fractionation of immobilized phosphorus indicated that Fe+Al-P increased most significantly and consistently among all the phosphorus fractions following the conversion of fly ash to zeolite. The PIC and Ca+Mg-P were closely related to Ca content (with r values of 0.9683 and 0.9651, respectively) rather than Mg content (with r values of 0.3920 and 0.3212, respectively). The r values of PIC and Fe+Al-P with Fe content (with r values of 0.4686 and 0.6385, respectively) were higher than those with Al content (with r values of -0.7857 and -0.3770, respectively). Although calcium and iron components were mainly involved in phosphate immobilization, there was no significant change of Ca and Fe content following the conversion of fly ash to zeolite. Increase in dissociated Fe(2)O(3) and specific surface area probably accounted for the enhancement in PIC of synthesized zeolites compared with corresponding fly ashes. The PIC value of zeolites showed a significant correlation with dissociated Fe(2)O(3) (r=0.6186). The specific surface area increased 26.0-89.4 times as a result of the conversion of fly ash to zeolite. The maximum removal of phosphate occurred within different pH ranges for zeolites which were synthesized from high, medium and low calcium fly ashes and this behavior was explained by the reaction of phosphate with calcium and iron components.     

Removal of boron from aqueous solution by clays and modified clays

In order to increase the adsorption capacities of bentonite, sepiolite, and illite for the removal of boron form aqueous solution, the clay samples were modified by nonylammonium chloride. Specific surface areas of the samples were determined as a result of N2 adsorption-desorption at 77 K using the BET method. X-ray powder diffraction analysis of the clays and modified clays was used to determine the effects of modifying agents on the layer structure of the clays. The surface characterization of clays and modified clay samples was conducted using the FTIR technique before and after the boron adsorption. For the optimization of the adsorption of boron on clays and modified clays, the effect of pH and ionic strength was examined. The results indicate that adsorption of boron can be achieved by regulating pH values in the range of 8-10 and high ionic strength. In order to find the adsorption characteristics, Langmuir, Freundlich, and Dubinin-Radushkevich adsorption isotherms were applied to the adsorption data. The data were well described by Freundlich and Dubinin-Radushkevich adsorption isotherms while the fit of Langmuir equation to adsorption data was poor. It was reached that modification of bentonite and illite with nonylammonium chloride increased the adsorption capacity for boron sorption from aqueous solution.     

Removal and recovery of uranium from aqueous solution by tea waste

Experiments on the removal and recovery of U(VI) from aqueous solution by tea waste were conducted. The adsorbent was characterized by scanning electron microscope and energy dispersive spectrometer before and after the adsorption treatment. The removal of U(VI) amounts to 86.80?% at optimum pH 6. The adsorption process reaches its equilibrium in 12?h at 308?K, and the kinetic characteristic can be described by the pseudo-second-order kinetic equation. The amount of adsorption increases from 22.92 to 142.21?mg?g^?1 with the decrease of tea waste dosage from 100 to 10?mg for solution with an initial uranium concentration of 50?mg?L^?1. Desorption for the four strippants is higher than 80?%. The equilibrium data are more agreeable with Freundlich isotherm than Langmuir isotherm.     

溶剂气浮法分离水中的Zn离子的研究

以双硫腙为配体,溴化十六烷基三甲基铵（CTAB）为表面活性剂。对Zn离子在无机相中形成的Zn-双硫腙-CTAB体系的溶剂气浮进行了研究。研究表明表面活性剂与Zn离子的物质的量之比为5：1,约1h水中的锌离子去除率可达98％。0．5mol／L NaCl大大提高体系的溶剂气浮的去除率,溶剂气浮的速率随着气流速率的增加而增加,共存溶质乙醇存在会使去除率降低,有机溶剂的量对溶剂气浮影响较小,溶剂气浮过程遵从假一级动力学。考察了不同温度下溶剂气浮的回收速率,计算了该过程中的气浮表观活化能为9．037kJ／mol。     

Removal of 2,4-dichlorophenol from aqueous solution by static-air-activated carbon fibers

Static-air-activated carbon fibers (ACFs) with lotus-root-like axially porous structure were used to adsorb 2,4-dichlorophenol (2,4-DCP) from aqueous solution. The adsorption isotherm was evaluated in the pH range 3.0-11.0. Results indicated that both Langmuir and Redlich-Peterson adsorption isotherms were appropriate for describing the adsorption characteristics of 2,4-DCP at various pH values and that lower pH values were favorable for adsorption. The adsorption of 2,4-DCP was controlled by the synergetic effects of pi-pi interaction and electrostatic attraction, and the former was dominant. Breakthrough curve results showed that the 2,4-DCP removal efficiency increased with an increase in the empty-bed contact time (EBCT). An EBCT of 0.660 min was sufficient for the adsorption of 2,4-DCP onto ACF, indicating a high adsorption rate. Desorption experiment results revealed that the ACF saturated with 2,4-DCP could be regenerated effectively by a 0.001 M NaOH solution.     

Removal of radiocobalt from aqueous solution by different sized carbon nanotubes

Batch adsorption technique was applied to study the adsorption of radiocobalt on multiwalled carbon nanotubes (CNTs) with deferent sizes. The aim of this work was to examine the effect of contact time, pH, solid content, foreign ions and CNT particle sizes on the removal of Co(II) ions from aqueous solutions by CNTs. The results indicated that the adsorption of Co(II) was strongly dependent on pH and the adsorption capacity was in inverse proportion to the particle sizes of CNTs. The adsorption of Co(II) was weakly affected by ionic strength and foreign ions. Ion exchange and surface complexation were the main adsorption mechanisms. The kinetics of Co(II) adsorption on CNTs was described well by pseudo-second-order model. The Langmuir and Freundlich models were applied to interpret the adsorption data. The results are important to understand the physicochemical behavior of Co(II) with CNTs, and for the application of CNTs in the preconcentration of radiocobalt from large volumes of aqueous solutions.     

生物炭去除水中四环素的研究进展

随着抗生素药物(如四环素)的大量使用,近几年抗生素的环境行为和毒性已经成为人们的研究焦点和热点.我国的地表水、地下水、市政污水、养殖废水等不同水体中都检测到了四环素等抗生素药物,引发的水生态问题受到了众多学者的广泛关注.生物炭因具有制备来源广泛且易得廉价、比表面积大、孔隙发达、官能团种类较多等优点被学者们重点关注,已有众多文献报道发现不同种生物炭对四环素的吸附具有优越的性能.本文综述了近年来不同生物质制备的生物炭对四环素的吸附影响以及不同水化条件对四环素对生物炭吸附特征的影响,并阐述了生物炭吸附四环素过程中所涉及的机理.对进一步探究生物炭对四环素吸附的影响具有一定的指导意义.     

Removal of thorium from aqueous solution by ordered mesoporous carbon CMK-3

The ability of ordered mesoporous carbon CMK-3 has been explored for the removal and recovery of thorium from aqueous solutions. The textural properties of CMK-3 were characterized using small-angle X-ray diffraction and N₂ adsorption–desorption, and the BET specific surface area, pore volume and the pore size were 1143.7 m²/g, 1.10 cm³/g and 3.4 nm. The influences of different experimental parameters such as solution pH, initial concentration, contact time, ionic strength and temperature on adsorption were investigated. The CMK-3 showed the highest thorium sorption capacity at initial pH of 3.0 and contact time of 175 min. Adsorption kinetics was better described by the pseudo-second-order model and adsorption process could be well defined by the Langmuir isotherm. The thermodynamic parameters, △G°(298 K), △H° and △S° were determined to be -0.74 kJ·mol^?1, 9.17 kJ·mol^?1 and 33.24 J·mol^?1·K^?1, respectively, which demonstrated the sorption process of CMK-3 towards Th(IV) was feasible, spontaneous and endothermic in nature. The adsorbed CMK-3 could be effectively regenerated by 0.02 mol/L HCl solution for the removal and recovery of Th(IV).     

Removal of Co(II) from aqueous solution by using hydroxyapatite

Herein, hydroxyapatite (HAP) was prepared by aqueous precipitation technique and was characterized by using FT-IR and XRD to determine its chemical functional groups and micro-structure. The removal of cobalt from aqueous solution to HAP was studied by batch technique as a function of various environmental parameters such as contact time, pH, ionic strength, foreign ions, fulvic acid (FA), and temperature under ambient conditions. The results indicated that the sorption of Co(II) on HAP was strongly dependent on pH and ionic strength. The presence of FA enhanced the sorption of Co(II) on HAP at low pH, whereas reduced Co(II) sorption on HAP at high pH. The Langmuir, Freundlich and D-R models were used to simulate the sorption isotherms at three different temperatures of 303.15, 323.15 and 343.15 K. The thermodynamic parameters (ΔH°, ΔS° and ΔG°) calculated from the temperature dependent sorption isotherms indicated that the sorption process of Co(II) on HAP was spontaneous and endothermic. The sorption of Co(II) was dominated by outer-sphere surface complexation and ion exchange at low pH, whereas inner-sphere surface complexation or surface precipitation was the main sorption mechanism at high pH values. The results suggest that the HAP is a suitable material in the preconcentration and solidification of Co(II) from large volumes of aqueous solutions.     

Removal of metal ions from aqueous solution by adsorption on the natural adsorbent CACMM2.

The adsorption of Cd2+, Cr3+, Cu2+, Fe3+, Ni2+, Pb2+ and Zn2+ from aqueous solution was used to study the sorption properties of the adsorbent CACMM2 extracted from a cactus. Quantitation of the cation concentrations was performed by HPLC with diode array detection using on-column complex formation with 8-hydroxyquinoline. Removal degree from 100 mg M(n+) l(-1) solutions followed the series: Cu>Cd>Fe>Ni>Cr>Zn. Henry and Freundlich constants were determined since adsorption did not reach saturation plateaux in the studied concentration interval. Sorption of chromium by CACMM2 was stronger than the sorption onto lignin, calcium oxalate and cellulose up to 1,000 mg Cr3+ l(-1). Copper and iron were desorbed to a greater extent, while lead adsorption was practically irreversible. CACMM2 was able to remove more than 83% of chromate in a freshly prepared and exhausted chromate commercial solution.