光纤技术在近红外光谱仪中的应用

探讨了光纤在近红外光谱技术应用中光纤材料选择、能量损耗和使用注意事项等问题。通过把光纤与近红外光谱技术相结合,使得近红外光谱仪从实验室走向现场,可适用于军事恶劣、危险和复杂的环境。为在军事条件下近红外光谱技术的应用提供了更大的空间。     

Ga对新型远红外Te基硫系玻璃光学性能的影响

用传统熔融淬冷法制备了新型远红外Te基硫系玻璃(100-x)(GeTe₄)-xGa (x=0, 5, 10 mol%).利用差热分析(DTA)、可见/近红外吸收光谱、红外透射光谱等技术,在GeTe₄玻璃的基础上,通过引入较高配位金属Ga, 研究其对玻璃组成、结构和性能的影响,利用经典的Tauc方程计算了样品光学带隙允许的直接跃迁、允许的间接跃迁及Urbach能量.分析结果表明:在GeTe₄玻璃中引入 关键词： 光学材料 硫系玻璃 光学带隙 红外光谱     

PbI2对远红外Te基硫系玻璃光学性能的影响

用传统的熔融淬冷法制备了一系列新型Ge-Te-PbI₂硫系玻璃,并且讨论了玻璃的形成区域. 利用X射线衍射(XRD)、差热分析(DTA)、可见/近红外吸收光谱、红外透过光谱等技术,研究重金属卤化物PbI₂对Ge-Te硫系玻璃组成、结构和性能的影响. 利用Tauc方程计算了样品的直接和间接光学带隙,根据金属标准和能量带隙理论讨论了玻璃光学带隙与组分变化的关系. 结果表明:PbI₂的引入,提高了Te玻璃的形成能力,而且玻璃的热稳定性良好;随着PbI₂含量的增加,玻璃的密度和折射率均增大,光学带隙减小,短波吸收截止边发生红移,玻璃的红外截止波长基本不变,达到了25 μm. 该系列玻璃可用于制备远红外长波波导器件. 关键词： Te基玻璃 2')" href="#">PbI₂ 光学带隙 红外光谱     

Study of optical properties of electrospun light-emitting polymer fibers

We realize light-emitting polymer fibers based on both optically inert polymers doped by molecules exhibiting optical gain and optically active conjugated polymers. Waveguiding properties of the produced polymer structures are demonstrated, with a loss coefficient of around 10³ cm⁻¹. We also find that single polymer fibers doped with gain molecules form Fabry–Pérot cavities, showing photoluminescence spectra with modes equally spaced by 1.7 nm. Coherent emission is demonstrated from fibers made upon increasing the excitation fluence above threshold values of the order of a few tens of μJ/cm².     

New method for strength improvement of silica optical fibers

The reliability and the expected lifetime of optical fibers used in telecommunication technologies are closely related to the chemical environment action on the silica network. To ensure the long-term mechanical strength of the optical fibers, a polymer coating was applied onto the fiber surface during fiber fabrication. This external coating is vital to ensure a long optical fiber lifetime. Its protective action includes several functions, such as to protect glass fiber from any external damage, to limit chemical attack, in particular that of water, and finally to ensure fatigue protection and bending insensitivity, especially during handling and in-service installation. Since the mechanical strength of the fiber is controlled by its surface characteristics, we propose a new method for increasing fiber strength.The silica optical fibers used were 125 μm in diameter, with a 62.5 μm thick epoxy-acrylate coating. Fibers were rolled up around two similar cylinders. Using a screw, these cylinders moved away from one another and thus subjected the fibers to stretching. Submitted to this mechanical loading, the distended fibers were plunged into hot water at 65 or 85 °C and aged for several days. Then, the fibers were removed from the water and various weights were suspended on the fiber ends. Thus, the fibers were subjected to a tensile loading in static fatigue for several days. Just before fiber rupture, the fibers were unloaded and subjected to dynamic tensile tests at different velocities.Result analysis proved that the aging in hot water increased the fiber strength. The Weibull's diagram study shows a bimodal dispersion of defects on the fiber surface and the important role of polymer coating.     

Visible,near-infrared and infrared optical properties of silica aerogels

Silica aerogel is an excellent thermal insulation material with a low thermal conductivity and a high porosity and has attracted great concern in applications. This paper was to experimentally investigate the optical properties of optically thick silica aerogel in the visible, near-infrared and infrared spectrum region. The fiber-loaded silica aerogel sample was prepared through sol–gel technique and supercritical drying process. Silica fibers were added into the aerogel during the preparation procedure to strength the skeleton of aerogel. As a comparison with the fiber-load silica aerogel, a silica fiber composite sample with the same chemical component and different physical structure was also prepared. A simplified two-flux model neglecting the boundary effect was used to describe the radiation propagation characteristics inside the samples. The spectral normal-hemispherical reflectances, transmittances, and normal emittances of silica aerogel and silica fiber samples were measured and compared in the wavelengths of 0.38–15 μm. Then the spectral optical constants of samples were determined using the experimental data. The spectral absorption and scattering coefficients of silica aerogel were within (0.01 cm⁻¹, 31.0 cm⁻¹) and (1.4 cm⁻¹, 25.8 cm⁻¹). The results showed that the spectrum region where the scattering coefficient is low usually corresponds to a high absorption coefficient. In addition, the total radiation properties of samples were predicted at high temperatures. The analysis of optical properties of silica aerogel is necessary to provide valuable data in applications.     

Compositional dependence of the optical properties of novel Ge-Ga-Te-CsI far infrared transmitting chalcohalide glasses system

A systematic series of (Ge₁₅Ga₁₀Te₇₅)_1−x(CsI)_x (x=0, 5, 10, 15 at%) far infrared transmitting chalcohalide glasses were prepared by the traditional melt-quenching method. The physical, thermal and optical properties were determined. The allowed direct transition and indirect transition of samples were calculated according to the Tauc equation. The results show that glass transition temperatures (T_g) were in the range 133-175 °C, with ΔT values between 81 and 130 °C. The highest values of metallization criterion (0.244) and energy gap (1.191 eV) were obtained for (Ge₁₅Ga₁₀Te₇₅)₈₅(CsI)₁₅. When the dissolved amount of CsI increased from 0 to 15 at%, the direct optical band gap and indirect optical band gap were in the ranges 0.629-1.075 eV and 0.438-0.524 eV, respectively. The Ge-Ga-Te-CsI glasses have an effective transmission window between 1.7 and 25 μm, encompassing the region of interest for bio-sensing applications.     

La掺杂浓度对PLZT薄膜红外光学性质的影响

采用溶胶-凝胶法在Pt/Ti/SiO2/Si衬底上制备了不同La掺杂浓度PLZT(x/40/60)薄膜- x射线衍射分析表明制备的PLZT(x/40/60)薄膜是具有单一钙钛矿结构的多晶薄膜- 通过红外椭圆偏振光谱仪测量了波长为2-5—12-6μm范围内PLZT薄膜的椭偏光谱，采用经典色 散模型拟合获得PLZT薄膜的红外光学常数，同时也拟合获得PLZT薄膜的厚度- 随着La掺杂浓 度的增大，折射率逐渐减小- 而消光系数除PLZT(4/40/60)薄膜外，呈现逐渐增大的趋势- 分析表明这些差异主要与PLZ 关键词： PLZT薄膜 红外光学性质 红外椭圆偏振光谱     

Electrical and optical properties of pure and KClO3-doped P(MMA-CO-4VPNO) polymer electrolyte films

Ion-conducting polymer electrolyte films based on a copolymer poly(methyl-methacrylate-co-4-vinyl pyridine N-oxide) [P(MMA-CO-4VPNO)] complexed with potassium chlorate (KClO₃) were prepared by solution cast technique. The complexation of KClO₃ salt with the polymer was confirmed by X-ray diffraction and infrared studies. The electrical conductivity and optical absorption of pure and KClO₃-doped P(MMA-CO-4VPNO) polymer electrolyte films have been studied. The electrical conductivity increased with increasing dopant concentration, which is attributed to the formation of charge transfer complexes. The variation of electrical conductivity with temperature shows two regions with two activation energies. Optical properties like direct band gap, indirect band gap, and optical absorption edge were investigated for pure and doped polymer films in the wavelength range 300–550 nm. It was found that the energy gaps and band edge values shifted to lower energies on doping. The behavior is in an agreement with the activation energies obtained from the conductivity data.     

两种不同外形红外发光管的光学性能比较

本文用几何光学基本定律对两种不同外形发光管的光学性能作了一般性的分析和探讨。通过具体的计算，从等效发光点、可被利用光能、聚光性能和使用场合等方面对它们进行了比较，用以指导光路设计，并提出了改进建议     

透极远红外光学材料制备及性能研究

在一定的温度、压力等条件下,采用有机材料(聚四氟乙烯)和无机晶体(KBr、CsI),通过热合技术研制出样品几何尺寸为Φ20mm×3-5mm、透射波段分别为15-38μm(PE-KBr)和15-60μm(PE-CsI)的透极远红外复合光学材料。抗腐蚀性能测试结果表明,材料耐强酸、强碱及部分有机溶剂。机械性能分析表明材料在小于115℃范围内可安全使用。极远红外透过率测试结果表明,在1-15μm波段,平均透过率小于15%,15-38μm和15-60μm极远红外波段,平均透过率大于50%,并对影响材料透过率的因素进行了分析。     

The wavelength dependence of gold nanorod‐mediated optical breakdown during infrared ultrashort pulses

This paper investigates the wavelength dependence of the threshold of gold nanorod‐mediated optical breakdown during picosecond and femtosecond near infrared optical pulses. It was found that the wavelength dependence in the picosecond regime is governed solely by the changes of a nanorod's optical properties. On the other hand, the optical breakdown threshold during femtosecond pulse exposure falls within one of two regimes. When the ratio of the maximum electric field from the outside to the inside of the nanorod is less then 7 (the absorption regime) the seed electrons are initiated by photo‐thermal emission, and the wavelength dependence in the threshold of optical breakdown is the result of optical properties of the nanoparticle. When the ratio is greater than 7 (the near‐field regime) more seed electrons are initiated by multiphoton ionization, and the wavelength dependence of the threshold of optical breakdown results from a combination of nanorod's optical properties and transitions in the order of multiphoton ionization. The findings of this study can guide the design of nanoparticle based optical breakdown applications. This analysis also deepens the understanding of nanoparticle‐mediated laser induced breakdown for picosecond and femtosecond pulses at near infrared wavelengths.

     

Design guidelines and characteristics of beam-shaping microstructure optical fibers

Microstructure optical fibers with flat-top fundamental mode are first proposed by introducing a low-index inner core into the core of index-guiding microstructure optical fibers. The design guidelines and characteristics of beam-shaping microstructure optical fibers are demonstrated. The interrelationships of inner-core index with laser wavelength, air hole diameter and size of inner core are investigated. The influence of the relative size of inner core on the spatial profile of the fundamental mode is demonstrated. Moreover, sensitivity of the flat-top fundamental mode profile from the slight change of the optimum inner-core index value is studied. Starting from these results we deduce that it is possible to fabricate beam-shaping microstructure fibers with nowadays technique.     

脉冲偏压电弧离子镀TiO2薄膜的力学与光学性能

用脉冲偏压电弧离子镀技术在玻璃基片上制备均匀透明的TiO₂薄膜.利用X射线衍射仪、原子力显微镜、扫描电子显微镜、紫外-可见透射光谱仪和纳米压痕仪等手段,对不同脉冲负偏压下合成薄膜的相结构、微观结构、表面形貌、力学和光学性能进行表征.结果表明，沉积态薄膜为非晶态.脉冲负偏压对薄膜性能有明显的影响.随偏压的增加，薄膜厚度、硬度和弹性模量均先增大后减小，前者峰值出现在100—200 V负偏压范围，后两者则在250—350V范围.300 V负偏压时薄膜硬度最高，薄膜达到原子级表面光滑度，均方 关键词： 2薄膜')" href="#">TiO₂薄膜 脉冲偏压电弧离子镀 硬度 折射率     

金刚石薄膜的红外椭圆偏振光谱研究

采用红外椭圆偏振光谱对微波等离子体化学气相沉积法（MPCVD）和热丝化学气相沉积法（H-FCVD）制备的金刚石薄膜在红外波长范围（2.5—12.5μm）的光学参数进行了测量.建立了不同的光学模型，且在模型中采用Bruggeman有效介质近似方法综合考虑了薄膜表面和界面的椭偏效应.结果表明，MPCVD金刚石膜的椭偏数据在模型引入了厚度为77.5nm的硅表面氧化层、HFCVD金刚石膜引入879nm粗糙层之后能得到很好的拟合.最后对两种模型下金刚石薄膜的折射率和消光系数进行了计算，表明MPCVD金刚石薄膜的红外 关键词： 金刚石薄膜 红外椭圆偏振光谱 光学参数 有效介质近似     

Improvement in thermo mechanical and optical properties of in situ synthesized PMMA/TiO2 nanocomposite

In this paper, transparent thin films of nano titania filled Poly(methyl methacrylate) (PMMA) composites were synthesized by solvent casting method using tetra hydro furan as a solvent, with in situ nonaqueous ‘sol-gel’ transformation involving the mixing of titanium isopropoxide (as sol-gel precursor) and methanol. The present research work is focused at studying the effect of titania loading on optical and mechanical behavior of transparent nano hybrid thin films. The effect of nano Titanium dioxide (TiO₂) loading on PMMA morphology was studied by using a scanning electron microscope (SEM). Bowl shaped structures were obtained in pure PMMA thin film, which were deformed on incorporation of TiO₂ nanoparticles. This nanocomposite exhibits enhanced optical and mechanical properties. The peak of UV absorption is blue shifted to 261 and 266?nm with the incorporation of TiO₂. At this wavelength, the absorption is increased up to approximately 397%. The nanocomposites exhibit increased tensile strength up to 40% and modulus up to 16%. Tg of PMMA increased from 84.8 to 86.7?°C on adding 1.25% TiO₂ nanoparticles.     

Effect of UV radiation on the optical and some structural properties of irregular rayon acetate fibers

This recent study shed demonstration on how the structural parameters changes due exposure to UV radiation and different wavelengths. So this article throws light on the changes of the optical properties and some structural properties due exposure to UV radiation and different wavelengths on irregular rayon acetate fibers. Pluta polarizing interference microscope is used to study the changes for refractive indices and birefringence with different exposure times at three different intensities on irregular rayon acetate fibers. As the principal optical parameters determined, these give an indication of the isotropic refractive index, stress optical coefficient, stress due to UV radiation, optical configuration parameter, segment anisotropy, the number of molecules per unit volume and polarizability of a monomer unit can be obtained. Also by using different wavelengths are given the spectral dispersions, Cauchy's dispersion constants, the resonant wavelength, the oscillation energy, the dispersion energy, the dielectric constant and the dielectric susceptibility for rayon acetate fibers with different wavelengths at room temperatures. Illustrations are given using graphs and microinterferograms.     

基于密度泛函理论探究拉伸应变对MoS2光电性能影响

本文用基于密度泛函理论的第一性原理方法研究了拉伸应变对MoS₂光电性能的影响.发现:稳定性最强的为本征MoS₂,最弱的为拉伸形变为30%的MoS₂模型.拉伸形变使Mo-S原子键长增大,周围电荷密度降低,键强减弱,并可以一定程度上改变Mo-S原子最外层电子的杂化强度及价带顶和导带底的电子移动.不同拉伸形变MoS₂模型对应的反射系数,随着拉伸应变的增加,反射峰值也逐渐增大.且频率范围在8.8 eV-9.15 eV区间内,紫外光处有较高的透光率,有望用于制备紫外光传感器等材料.     

一例典型红外光学系统的计算分析

计算分析美国探测金星水手Ⅱ号宇宙飞船上安置的红外辐射计光学系统，说明了光学系统的光学特征、像差校正原理及其结构和应用特点．     

Mechanical properties,lattice thermal conductivity,infrared and Raman spectrum of the fullerite C24

Lightweight carbon materials with excellent thermal and mechanical properties have important applications in aerospace industry. In this study, the stability, mechanical properties, lattice thermal conductivity, electronic structure, infrared and Raman spectrum of sp³ hybridized low-density fullerite C₂₄ were investigated according to density functional theory (DFT) calculations. It was found that the fullerite C₂₄ was both thermodynamic and dynamic stable. Quasi-harmonic approximation and Grüneisen parameter calculations clarified why the fullerite C₂₄ had a positive thermal expansion coefficient at low temperature. The fullerite C₂₄ also exhibited excellent mechanical properties. Interestingly, the Vickers hardness of carbon allotropes was found to almost be linear proportional to the density of a carbon material. HSE06 electronic structure calculations showed that it was a semiconductor with direct bandgap of 2.56 eV. Anharmonic lattice dynamic calculations showed that its thermal conductivity was higher than semiconductor silicon. Besides, Raman and infrared active modes as well as the corresponding spectra were presented.