Preconcentration of chlorophenols in water samples using threedimensional graphene-based magnetic nanocomposite as absorbent

In this paper, a novel magnetic solid-phase extraction method using three-dimensional graphene-based magnetic nanocomposite as adsorbent for the preconcentration of several chlorophenols from water samples prior to high-performance liquid chromatography analysis was developed. Various experimental parameters were investigated. Under the optimum conditions, the enrichment factors of the method were in the range of 186–312, and the limit of detection(S/N = 3) was 0.10 ng/mL. The recoveries of the method were in the range between 85.1% and 101.2%. The developed method has been successfully applied to the determination of chlorophenols in environmental water samples.     

Analysis of nitrobenzene compounds in water and soil samples by graphene composite-based solid-phase microextraction coupled with gas chromatography–mass spectrometry

In this work, solid-phase microextraction coupled with gas chromatography–mass spectrometry was developed to determine trace levels of nitrobenzene compounds in water and soil samples. Graphene was chosen as the extraction material and its composite was coated on a stainless steel wire through sol–gel technique for the solid phase microextraction. The key parameters influencing the extraction efficiency were optimized. Under the optimal conditions, the linearity for the compounds was observed in the range of 0.02–15.0 mg/L for water samples, and 0.2–60.0 mg/kg for soil samples, with the correlation coefficients（r） of 0.9966–0.9987. The limits of detection of the method were 0.0025–0.005 mg/L for water samples, and 0.02–0.04 mg/kg for soil samples. The recoveries for the spiked samples were in the range of 72.0%–113.2%, and the precision, expressed as the relative standard deviations, was less than 12.1%.     

Metsulfuron-methyl Molecularly Imprinted Stir Bar Sorptive Extraction Coupled with High Performance Liquid Chromatography for Trace Sulfonylurea Herbicides Analysis in Complex Samples

Metsulfuron-methyl molecularly imprinted polymer(MIP)-coated stir bar was prepared for sorptiveextraction of sulfonylurea herbicides in complex samples. The MIP-coating was about 21.3 祄 thickness with the relative standard deviation(RSD) of 4.4%(n=10). It was homogeneous and porous with good thermal stability and chemical stability. The extraction capability of the MIP-coating was 2.8 times over that of the non-imprinted polymer (NIP)-coating in hexane. The MIP-coating exhibited selective adsorption ability to the template and its analogues. The extraction conditions, including extraction solvent, desorption solvent, extraction time, desorption time and stirring speed, were optimized. A method for the determination of six sulfonylurea herbicides by MIP-coated stir bar sorptive extraction coupled with high performance liquid chromatography(HPLC) was developed. The linear range was 10-200 礸/L and the detection limits were within a range of 2.0-3.3 礸/L. It was also applied to the analysis of sulfonylurea herbicides in spiked river water, soil and rice samples.     

Determination of synthetic phenolic antioxidants in essence perfume by high performance liquid chromatography with vortex-assisted,cloud-point extraction using AEO-9

This study aimed to establish a rapid analytical method to determine antioxidants in essence. A simple,efficient and practical, vortex-assisted, cloud-point extraction(VACPE) procedure is proposed for extracting and pre-concentrating four different of synthetic phenolic antioxidants(SPAs), propyl gallate(PG), tert-butylhydroquinone(TBHQ), butylated hydroxyanisole(BHA), butylated hydroxytoluene(BHT) in essence prior to high performance liquid chromatography(HPLC) analysis. The non-ionic surfactant, fatty alcohol polyoxyethylene ether-9(AEO-9), was used as extractant and vortex-mixing was utilized to reduce extraction time and improve extraction efficiency. The effective parameters of the extraction process, such as volume of extraction solvent, pH, vortex-mixing time, equilibration temperature and time, were optimized. Under the optimum conditions, the linear range of PG, TBHQ,BHA and BHT was 8.0–800 ng/mL. All correlation coefficients of the calibration curves were higher than0.996 and relative standard deviations(RSD, n = 5) were 2.36%–5.46%. The proposed method was successfully applied to the extraction and determination of antioxidants in essence samples with satisfactory relative recoveries of 89.4%–103.5%. The results confirmed the SPAs of essence could be effectively monitored by this method and also established good reference criteria for essence.     

Identification of in vitro and in vivo metabolites of 12β-hydroxylveratroylzygadenine associated with neurotoxicity by using HPLC–MS/MS

Metabolism study was carried out on 12b-hydroxylveratroylzygadenine(VOG) that is a cevine-type alkaloid existing in Veratrum nigrum L. and a neurotoxic component. In order to better understand the potential mechanism of neurotoxicity of VOG, this study measured VOG-induced DNA damage in the cerebellum and cerebral cortex of mice after 7 days repetitive oral dose by using single-cell gel electrophoresis(Comet assay). High performance liquid chromatography-tandem mass spectrometry(LC–MS/MS) was developed and applied to separate and identify in vitro and in vivo metabolites of VOG for investing the possible relationship of metabolism and neurotoxicity. In vitro experiment was carried out using rat liver microsomes, while the in vivo study was conducted on rats. The obtained results indicated that VOG might cause DNA damage in cerebellum and cerebral cortex of mice in a dosedependent manner. Hydrolysis of ester bond and O-demethylation were proposed to be the main in vivo metabolic pathways of VOG, while the major in vitro metabolic pathways were proposed as methyl oxidation to aldehyde, dehydrogenation, hydrolysis of ester bond, hydrolysis of ester bond together with acetylation, and methoxylation. O-Demethylation reaction was likely to be associated with reactive oxygen species production, leading to the DNA damage.     

Combination of ionic liquid dispersive liquid-phase microextraction and high performance liquid chromatography for the determination of triazine herbicides in water samples

A temperature-controlled ionic liquid dispersive liquid-phase microextraction in combination with high performance liquid chromatography was developed for the enrichment and determination of triazine herbicides such as cyanazine,simazine,and atrazine in water samples.1-Octyl-3-methylimidazolium hexafluorophosphate([C8MIM][PF6]) was selected as the extraction solvent.Several experimental parameters were optimized.Under the optimal conditions,the linear range for cyanazine was in the concentration range of 0.5–80 mg/L and the linear range for simazine and atrazine was in the range of1.0–100 mg/L.The limit of detection(LOD,S/N = 3) was in the ranges of 0.05–0.06 mg/L,and the intra day and inter day precision(RSDs,n = 6) was in the ranges of 3.2%–6.6% and 4.8%–8.9%,respectively.Four real water samples were analyzed with the developed method,and the experimental results showed that the spiked recoveries were satisfactory.All these exhibited that the developed method was a valuable tool for monitoring such pollutants.     

Determination of macrolides in livestock excreta by syringe purification coupled with liquid chromatography tandem mass spectrometryEI北大核心CSCD

A method of syringe-dispersive solid-phase extraction combined with ultrahigh performance liquid chromatography with tandem mass spectrometry for the simultanous determination of 10 macrolides in manurebased fertilizers was developed. After extraction with methanol and acetonitrile,the extracts were purified by insyringe dispersion solid-phase extraction in syringes pre-filled with 60 mg PSA and 30 mg C18. The resulted extracts were further separated by a BEH C18 column,detected by multiple reaction monitoring in electrospray positive ion mode,and quantified by matrix-matched external standard method. The results showed that the recoveries of the target compounds ranged from 70% to 110% at three spiked levels（10,30,and 50 μµg/kg）with the relative standard deviations ranged from 1.4% to 12%. The limits of detection and quantification were 0.57 1.75 and 2.77-5.40 μµg/kg,respectively. This method was suitable for the simultaneous determination of residual macrolides in organic fertilizers. © 2023, Youke Publishing Co.,Ltd. All rights reserved.     

Porous boronate affinity monolith for on-line extraction coupled to high-performance liquid chromatography for sensitive analysis of heterocyclic aromatic amines in food samples

A novel on-line solid-phase microextraction–high-performance liquid chromatography(SPME–HPLC)system was developed for the determination of heterocyclic aromatic amines(HAAs) in food samples. A poly(vinylphenylboronic acid-co-ethylene glycol dimethacrylate) polymer monolith was prepared for on-line efficient extraction and large-volume injection was used to increase the sensitivity of detection.The polymermonolith, based on a ternary porogen, was prepared by in situ polymerization of vinylphenylboronic acid(VPBA) and ethylene glycol dimethacrylate(EGDMA) in a fused-silica capillary column. It showed good permeability, high extraction capacity, and high selectivity. The column-tocolumn reproducibility was satisfactory, and the enrichment factors for HAAs were 3746–7414.Conditions influencing the on-line extraction efficiency, including p H of sample solutions, flow rate of extraction and desorption, and desorption volume, were investigated. The proposed method had low limit of detection(0.10–0.15 ng/L) and good linearity. Trace HAAs in roast beef and lamb samples were determined, and the amounts of 2-amino-3-methylimidazo[4,5-f]quinoline, 2-amino-3,4-dimethylimidazo[4,5-f]quinoline, 2-amino-3,8-dimethylimidazo[4,5-f]quinoxaline, 2-amino-3,4,8-trimethylimidazo[4,5-f]quinoxaline, and 2-amino-3,4,7,8-tetramethyl-3H-imidazo[4,5-f]quinoxaline in these samples were 0.235–2.08 ng/g. The recoveries for the five HAAs ranged from74.3% to 119%, and the relative standard deviation(RSDs) were less than 8.2%. The results showed that the proposed on-line method was highly sensitive for monitoring HAAs in different food samples.     

Molar Mass Distribution and Chain Conformation of Polysaccharides from Fortunella margarita （Lour.） Swingle

In order to study the effects of different extraction methods on the molar mass distribution and chain conformation of Fortunella margarita(Lour.) Swingle polysaccharides(FP), we used extraction by hot water(WFP), ultrasonic-assisted treatment(UFP), microwave-assisted treatment(MFP) and ultrasonic/microwave-assisted treatment(UMFP), and then Fourier transform infrared(FT-IR) spectroscopy as well as 1H and 13 C nuclear magnetic resonance(NMR) spectroscopy to characterize the structural properties of FP extracted. The molar weight(Mw), polydispersity index(Mw/Mn), root-mean-square(RMS) turning radius(Rg), molar mass distribution and chain conformation of FP were studied systematically using size-exclusion chromatography(SEC), multi-angle laser light-scattering(MALLS) and refractive index(RI). WFP, UFP, MFP and UMFP are all typical carbohydrates according to 1H NMR, 13 C NMR and FT-IR measurements. The type of glycosidic linkage is mainly a β-glycosidic bond with a small amount of α-glycosidic bond. The results obtained by the SEC-MALLS-RI system showed the molar masses of WFP and UMFP were distributed mainly in the range of 5.0×106~1.0×107 g·mol–1 and they accounted for 57.80% and 56.84% of total FP, respectively. The molar masses of UFP and MFP were distributed mainly in the 1.0×106~5.0×106 g·mol–1 range, which accounted for 38.24% and 52.39% of FP, respectively. WFP and UMFP in water were uniform spherical polymers; UFP and MFP were typical highly branched polymers and the degree of branching for MFP was higher compared to UFP. These results indicated the ultrasonic- and microwave-assisted extraction methods caused a significant decrease of the molar mass of FP but the ultrasonic/microwave synergistic extraction method had no effect.     

Ionic liquid based dispersive liquid-liquid microextraction of aromatic amines in water samples

In this work, a new microextraction method termed ionic liquid based dispersive liquid-liquid microextraction （IL-DLLME） was demonstrated for the extraction of 2-methylaniline, 4-chloroaniline, 1-naphthylamine and 4-aminobiphenyl in aqueous matrices. After extraction the ionic liquid （IL） phase was injected directly into the high performance liquid chromatography （HPLC） system for determination. Some parameters that might affect the extraction efficiency were optimized. Under the optimum conditions, good linear relationship, sensitivity and reproducibility were obtained. The limits of detection （LOD, S/N = 3） for the four analytes were in the range of 0.45-2.6 μg L^-1. The relative standard deviations （R.S.D., n = 6） were in the range of 6.2-9.8%. This method was applied for the analysis of the real water samples. The recoveries ranged from 93.4 to 106.4%. The main advantages of the method are high speed, high recovery, good repeatability and volatile organic solvent-free.     

Determination of polybrominated diphenyl ethers at trace levels in environmental waters using hollow-fiber microporous membrane liquid-liquid extraction and gas chromatography-mass spectrometry

In this study, we present a simple and easy-to-use extraction method that is based on a hollow-fiber microporous membrane liquid-liquid extraction (HF-MMLLE), as an extraction technique, followed by gas chromatography-mass spectrometry (GC-MS) to determine a group of brominated flame retardants (BFRs), polybrominated diphenyl ethers (PBDEs), at trace levels in aqueous samples. The hollow-fiber membrane (HF) filled with organic solvent was immersed into the aqueous sample, spiked with the analytes at ng l(-1) level, and stirred for 60 min. The proposed method could attain enrichment factors (E(e)) up to 5200 times, after optimising parameters, such as organic solvent, stirring speed and extraction time, that affect the extraction. The HF-MMLLE-GC-MS method was successfully applied to the extraction of PBDEs from tap, river and leachate water samples with spike recoveries ranging from 85% to 110%. The method validation with reagent and leachate water samples provided good linearity, detection limits of 1.1 ng l(-1) or lower, both in reagent and leachate water, as well as satisfactory precision in terms of repeatability and reproducibility with values of % relative standard deviation (%RSD) lower than 8.6 and 16.9, respectively.     

Determination of Polybrominated Diphenyl Ethers in Water Samples Using Effervescent-Assisted Dispersive Liquid-Liquid Icroextraction with Solidification of the Aqueous Phase

An effective and sensitive method is necessary for the determination of polybrominated diphenyl ethers (PBDEs) pollutants in water. In this study, effervescent-assisted dispersive liquid-liquid microextraction with solidification of the aqueous phase (EA-DLLME-SAP), followed by Gas Chromatography-Tandem Mass Spectrometry (GC-MS-MS) quantitative analysis, was established for the preconcentration and determination of PBDEs in real environmental water samples. 1,1,2,2-Tetrachloroethane was used as the extractant and directly dispersed into the water phase of the aqueous samples with the aid of a large number of carbon dioxide bubbles generated via the acid-base reaction of acetic acid and sodium bicarbonate, which did not require the use of a dispersant during the extraction process. The key factors affecting the extraction recovery were optimized, and an internal standard was used for quantitative analysis, which gave good linearity ranges of 1–100 ng·L⁻¹ (BDEs 28, 47, 99, and 100), 2–200 ng·L⁻¹ (BDEs 153, 154, and 183) and 5–500 ng·L⁻¹ (BDE 209) with limits of quantification in the range of 1.0–5.0 ng·L⁻¹. The accuracy was verified with relative standard deviations < 8.5% observed in tap, lake, river and reservoir water samples with relative recoveries ranging from 67.2 to 102.6%. The presented method contributes to the determination of PBDEs in environmental water samples.     

Multiwalled carbon nanotubes coated fibers for solid-phase microextraction of polybrominated diphenyl ethers in water and milk samples before gas chromatography with electron-capture detection

Determination of polybrominated diphenyl ethers (PBDEs) in environmental samples has raised great concerns due to the widespread use of PBDEs and their potential risk to humans. Solid-phase microextraction (SPME) is a fast, simple, cost-effective, and green sample preparation technique and is widely used for environmental analysis, but reports on the application of SPME for determination of PBDEs are very limited, and only a few publications dealing with commercial SPME fibers are available for extraction of PBDEs. Herein, we report a novel SPME method using multiwalled carbon nanotubes (MWCNTs) as the SPME fiber coating for gas chromatography with electron-capture detection (GC-ECD) of PBDEs in environmental samples. The MWCNTs coating gave much higher enhancement factors (616-1756) than poly (5% dibenzene-95% dimethylsiloxane) coating (139-384) and activated carbon coating (193-423). Thirty-minute extraction of 10 mL of sample solution using the MWCNTs coated fiber for GC-ECD determination yielded the limits of detection of 3.6-8.6 ng L(-1) and exhibited good linearity of the calibration functions (r(2)>0.995). The precision (RSD%, n=4) for peak area and retention time at the 500 ng L(-1) level was 6.9-8.8% and 0.6-0.9%, respectively. The developed method was successfully applied for the analysis of real samples including local river water, wastewater, and milk samples. The recovery of the PBDEs at 500 ng L(-1) spiked in these samples ranged from 90 to 119%. No PBDEs were detected in the river water and skimmed milk samples, whereas in the wastewater sample, 134-215 ng L(-1) of PBDEs were found. The PBDEs were detected in all whole fat milk samples, ranging from 13 to 484 ng L(-1). In a semiskimmed milk sample, only BDE-47 was found at 21 ng L(-1).     

Ultrasound-assisted leaching-dispersive solid-phase extraction followed by liquid-liquid microextraction for the determination of polybrominated diphenyl ethers in sediment samples by gas chromatography-tandem mass spectrometry

Ultrasound-assisted leaching-dispersive solid-phase extraction followed by dispersive liquid-liquid microextraction (USAL-DSPE-DLLME) technique has been developed as a new analytical approach for extracting, cleaning up and preconcentrating polybrominated diphenyl ethers (PBDEs) from sediment samples prior gas chromatography-tandem mass spectrometry (GC-MS/MS) analysis. In the first place, PBDEs were leached from sediment samples by using acetone. This extract was cleaned-up by DSPE using activated silica gel as sorbent material. After clean-up, PBDEs were preconcentrated by using DLLME technique. Thus, 1 mL acetone extract (disperser solvent) and 60 μL carbon tetrachloride (extraction solvent) were added to 5 mL ultrapure water and a DLLME technique was applied. Several variables that govern the proposed technique were studied and optimized. Under optimum conditions, the method detection limits (MDLs) of PBDEs calculated as three times the signal-to-noise ratio (S/N) were within the range 0.02-0.06 ng g⁻¹. The relative standard deviations (RSDs) for five replicates were <9.8%. The calibration graphs were linear within the concentration range of 0.07-1000 ng g⁻¹ for BDE-47, 0.09-1000 ng g⁻¹ for BDE-100, 0.10-1000 ng g⁻¹ for BDE-99 and 0.19-1000 ng g⁻¹ for BDE-153 and the coefficients of estimation were ≥0.9991. Validation of the methodology was carried out by standard addition method at two concentration levels (0.25 and 1 ng g⁻¹) and by comparing with a reference Soxhlet technique. Recovery values were ≥80%, which showed a satisfactory robustness of the analytical methodology for determination of low PBDEs concentration in sediment samples.     

Development of an analytical procedure for the determination of polybrominated diphenyl ethers in environmental water samples by GC–ICP-MS

Polybrominated diphenyl ethers (PBDEs) are flame retardants, which due to their widespread use are frequently present as pollutants in the environment. In the EU Water Framework Directive (WFD) six PBDE congeners (BDE 28, BDE47, BDE 99, BDE 100, BDE 153 and BDE 154) are listed as priority substances. The uncertainty of the analytical method used for their determination in water samples at environmental quality standard (EQS) level (0.5 ng L⁻¹ for the ΣPBDEs) should be equal or less than 50% and the limit of quantification (LOQ) for ΣPBDEs below 0.15 ng L⁻¹. To meet these requirements, an analytical procedure for the determination of these six PBDEs in environmental water samples by gas chromatography–inductively coupled plasma mass spectrometry (GC–ICP-MS) was developed. The acidification of water samples to pH 2 maintained the stability of PBDEs for at least 20 days. The use of Tris–citrate buffer enabled efficient desorption of PBDEs from suspended particulate matter (SPM) and humic acids (HA), and their further quantitative solvent extraction into 2 mL of iso-octane. When 300 mL of water sample was used for analysis and the organic phase concentrated to 25 μL, the expanded uncertainty for determination of PBDEs at EQS level was found to be around 40% (a coverage factor for a confidence level of 95%, k = 2), and the LOQ for the ΣPBDEs 0.109 ng L⁻¹. Finally, to demonstrate the applicability of the newly developed GC–ICP-MS procedure, PBDEs were determined in river and sea water samples.     

Solid-phase microextraction for the analysis of short-chain chlorinated paraffins in water samples

A novel solid-phase microextraction (SPME) method coupled to gas chromatography with electron capture detection (GC-ECD) was developed as an alternative to liquid-liquid and solid-phase extraction for the analysis of short-chain chlorinated paraffins (SCCPs) in water samples. The extraction efficiency of five different commercially available fibres was evaluated and the 100-microm polydimethylsiloxane coating was the most suitable for the absorption of the SCCPs. Optimisation of several SPME parameters, such as extraction time and temperature, ionic strength and desorption time, was performed. Quality parameters were established using Milli-Q, tap water and river water. Linearity ranged between 0.06 and 6 microg l(-1) for spiked Milli-Q water and between 0.6 and 6 microg l(-1) for natural waters. The precision of the SPME-GC-ECD method for the three aqueous matrices was similar and gave relative standard deviations (RSD) between 12 and 14%. The limit of detection (LOD) was 0.02 microg l(-1) for Milli-Q water and 0.3 microg l(-1) for both tap water and river water. The optimised SPME-GC-ECD method was successfully applied to the determination of SCCPs in river water samples.     

The use of copper(II) isonicotinate-based micro-solid-phase extraction for the analysis of polybrominated diphenyl ethers in soils

A micro-solid-phase extraction (μ-SPE) device was developed by filling copper(II) isonicotinate coordination polymer (Cu(4-C₅H₄N-COO)₂(H₂O)₄) into a porous polypropylene envelope, and the μ-SPE, coupling with gas chromatography (GC) with a micro-cell electron capture detector (μ-ECD), was used for extraction and determination of PBDEs in soils. Variables affecting extraction procedures, including temperature, water volume, extraction time, and desorption time, were investigated in a spiked soil, and the parameters were optimized. Under the optimal experimental conditions, the method detection limits for seven PBDEs (BDE-28, 47, 99, 100, 153, 154, and 183) were in the range of 0.026–0.066 ng g⁻¹, and the reproducibility was satisfactory with the relative standard deviation in range of 1.3–10.1%. Good linear relationship between PBDEs concentrations and GC signals (defined as peak area) was obtained in the range between 0.1 and 200 ng g⁻¹. The recovery of the seven PBDEs by μ-SPE varied from 70 to 90%, which was comparable to that determined by accelerated solvent extraction method. Finally, the proposed method was used to determine PBDEs in several field-contaminated soils, and it was suggested that the μ-SPE is a promising alternative microextraction technique for the detection of PBDEs in soils.     

Dispersive liquid-liquid microextraction followed by reversed phase HPLC for the determination of decabrominated diphenyl ether in natural water

A simple, rapid, and efficient method, dispersive liquid-liquid microextraction (DLLME), has been developed for the extraction and preconcentration of decabrominated diphenyl ether (BDE-209) in environmental water samples. The factors relevant to the microextraction efficiency, such as the kind and volume of extraction and dispersive solvent, the extraction time, and the salt effect, were optimized. Under the optimum conditions (extraction solvent: tetrachloroethane, volume, 22.0 microL; dispersive solvent: THF, volume, 1.00 mL; extraction time: below 5 s and without salt addition), the most time-consuming step is the centrifugation of the sample solution in the extraction procedure, which is about 2 min. In this method, the enrichment factor could be as high as 153 in 5.00 mL water sample, and the linear range, correlation coefficient (r(2)), detection limit (S/N = 3), and precision (RSD, n = 6) were 0.001-0.5 microg/mL, 0.9999, 0.2 ng/mL, and 2.1%, respectively. This method was successfully applied to the extraction of BDE-209 from tap, East Lake, and Yangtse River water samples; the relative recoveries were 95.8, 92.9, and 89.9% and the RSD% (n = 3) were 1.9, 2.7, and 3.5%, respectively. Comparison of this method with other methods, such as solid-phase microextraction (SPME), and single-drop microextraction (SDME), indicates that DLLME is a simple, fast, and low-cost method for the determination of BDE-209, and thus has tremendous potential in polybrominated diphenyl ethers (PBDEs) residual analysis in environmental water samples.     

Trace Enrichment and HPLC Analysis of Chlorophenols in Environmental Samples,Using Precolumn Sample Preconcentration and Electrochemical Detection

Abstract

A HPLC method has been developed for trace analysis of chlorophenols in the 0.2–2 ppb range from spiked water samples. Simple liquid-liquid extraction followed by on-line preconcentration of total mono- and dichlorophenols has been performed using a divinylbenzene-styrene copolymeric sorbent (PRP₁) as packing material for the precolumn. The chlorophenols have been eluted from the precolumn on an analytical column (5μm LiChrosorb RP-18, 12.5 cm × 4 mm) by use of a switching valve system followed by separation. Detection was carried out with an electrochemical detector. The linearity of the detector response has been proved over two orders of magnitude. The detection limit of chlorophenols by means of the electrochemical method is in the lower picogram range. The recoveries of the isomeric chlorophenols from spiked river water samples having initial concentrations of 2ppb are usually 70–90%. The procedure has been applied to drinking water and river water.     

Solid-phase microextraction with simultaneous oxidative sample treatment for the sensitive determination of tetra- to hexa-brominated diphenyl ethers in sediments

Solid-phase microextraction (SPME) is an effective technique for the extraction of polybrominated diphenyl ethers (PBDEs) from environmental water samples. Although it has been also applied to sediments, the organic content of this matrix causes an exponential decrease in the yield of the extraction. This work presents an improved SPME procedure for the sensitive determination of six PBDEs (tetra- to hexa-brominated congeners) in sediments containing up to 6% of total organic carbon (TOC). Samples (0.25–0.5 g) were accurately weighed in 22 mL glass vessels, mixed with a given amount of potassium permanganate, 0.5 mL of sulphuric acid and 5 mL of water. Extractions were performed at 100 °C, for 40 min, using a polyacrylate (PA) coated fibre in the headspace (HS) mode. Potassium permanganate showed a dramatic, positive effect on the yield of the extraction. Its optimum amount was related to the TOC of the sediment, with overall highest responses attained for 40 mg of oxidant per mg of organic carbon in the SPME vessel. Under final working conditions, the combination of SPME with gas chromatography coupled to tandem mass spectrometry (GC–MS/MS) provided relative standard deviations (RSDs) below 14%, relative recoveries from 76 to 111% and limits of quantification (LOQs) lower than 0.15 ng g⁻¹ for all the investigated PBDEs in spiked river and marine sediments with different TOC. The performance of the method was also evaluated satisfactorily with a medium complexity (TOC 6.7%), real-life polluted sediment, previously analyzed in inter-laboratory comparison exercises.