水蒸气存在时Mo/HZSM-5催化剂上的甲烷芳构化反应性能

研究了水蒸气存在条件下Mo/HZSM-5沸石分子筛催化剂上的甲烷芳构化反应行为,发现水蒸气的引入可以明显地降低甲烷芳构化反应的起始温度,从而在较为温和的条件下实现甲烷的活化.适量水蒸气的加入可以在一定程度上改善Mo/HZSM-5催化剂的稳定性,过量水蒸气的引入则会抑制甲烷芳构化反应.在反应温度为973 K时,引入适量的水蒸气对芳构化反应产物的分布没有明显影响在低温条件下的甲烷芳构化反应过程中检测到有乙烯生成,该结果支持了甲烷芳构化反应可能经历了乙烯这一中间产物的机理.实验结果还表明,水蒸气对催化剂上的积炭量没有明显的影响.     

Mo/HZSM-5催化剂上甲烷无氧芳构化反应——HZSM-5分子筛脱铝的影响

采用两种不同的脱铝方法对HZSM-5分子筛进行了预处理,并利用MAS NMR和吸附吡啶的FT-IR对分子筛的结构和酸性质进行了表征,考察了分子筛的脱铝程度对Mo基催化剂上甲烷芳构化反应性能的影响.结果表明,HZSM-5分子筛的酸性过强或B酸量不足,均会导致催化剂严重积炭,但积炭成因不同.母体HZSM-5分子筛上的强B酸中心的存在可促使催化剂上反应中间物种深度脱氢,造成催化剂在反应过程中严重积炭.经水热处理的HZSM-5分子筛,骨架铝脱出严重,造成B酸活性中心不足以及部分微孔阻塞,不利于C2中间物种芳构化,导致芳烃选择性显著降低.经高温N2处理的HZSM-5分子筛,骨架铝脱出相对缓和,在消除母体分子筛上强B酸中心的同时,保留了较多的弱B酸中心,既可满足C2中间物种芳构化反应的需要,又可有效抑制催化剂积炭,导致甲烷芳构化反应性能显著改善.     

微波加热条件下ZnNi/HZSM-5催化剂上烷烃的芳构化反应

The aromatization of n hexane and mixed C 4 hydrocarbon was investigated under microwave heating over ZnNi/HZSM 5 catalyst of lower activity in order to compare with that under the conventional heating. For the n hexane aromatization, the selectivity for benzene and toluene by the microwave heating at 450 ℃ increases by 4% and 5%, respectively, and the aromatics yield by the microwave heating at 480℃ increases by 4% , compared with those by the conventional heating. For the mixed C 4 olefine aromatization, the BTX yield by the microwave heating at 400 ℃ increases by 17 08% and the aromatics selectivity is also higher than that by the conventional heating.     

Mo/HZSM-5催化剂载体对甲烷无氧芳构化反应的影响

着重研究了挤条成型的纳米Mo/HZSM-5催化剂在甲烷无氧芳构化反应中的催化性能.结果表明,Al2O3载体的加入减少了催化剂的B酸量,对甲烷无氧芳构化反应不利,导致甲烷转化率降低,并且催化剂积碳严重.通过适量添加SiO2载体,减少Al2O3载体的量,可以使催化剂的B酸量提高,从而可提高甲烷转化率,并且可降低催化剂的积碳量.     

烯烃在HZSM-5分子筛上原位芳构化反应的研究

烯烃在ZSM-5分子筛上转化成芳烃的反应是一个非常复杂的反应,既包括聚合裂解反应,又包括氢转移、脱氢环化反应,同时也包括烷基转移和脱烷基等反应,对于这一复杂反应的机理研究较少.Vedrine等人[1]认为烯烃首先在酸性位上通过氢转移生成戊二烯正碳离子,接着环化以及扩环反应生成     

Zn/H-ZSM-5催化剂上的二甲醚芳构化反应

 考察了 H-ZSM-5 和 Zn/H-ZSM-5 催化剂的二甲醚芳构化性能. 结果表明, H-ZSM-5 分子筛催化剂酸性的增强和酸中心的增多有利于二甲醚芳构化. 当在 H-ZSM-5 催化剂中加入 2% Zn 时, 在 360 oC 下反应时总芳烃收率从 50.0% 增加至 66.2%, C8 芳烃收率从 28.6% 增加到 39.0%. 反应温度升高到 480 oC 时, 总芳烃收率增加至 78.0%.     

碳四烃在改性HZSM-5分子筛上芳构化研究

研究了炼厂混合C_4烃在Zn、Ga、Cr、La改性的HZSM-5分子筛催化剂上的芳构化反应,采用TPD和IR测定了催化剂的表面酸性质。结果表明,用Zn(3%)和Zn(2%)Ga(1%)改性的HZSM-5分子筛具有较好的芳构化性能;各改性HZSM-5分子筛催化剂芳构化性能变化与表面酸性有关,总酸量下降,芳构化活性下降,强B酸中心减少,深度裂解反应减少;Zn的单组分和双组分改性的HZSM-5分子筛催化剂芳构化活性的增高与表面强L酸浓度增加和吡啶吸附IR谱中的1615cm~(-1)吸收峰出现有关。     

无粘结剂成型的Zn/ZSM-5催化剂上混合碳四烃类芳构化反应性能

制备了无粘结剂成型的Zn/ZSM-5分子筛催化剂,并与机械压片和引入氧化铝或氧化硅粘结剂成型的催化剂相比较,采用N2-物理吸附-脱附、扫描电子显微镜、NH3-程序升温脱附、吡啶吸附红外光谱和X射线光电子能谱等手段对催化剂进行了表征,并评价了催化剂上混合碳四烃类芳构化反应性能.结果表明,相对于机械压片和引入粘结剂成型的催...     

乙烷添加对 Mo/HZSM-5 催化剂上甲烷芳构化反应的影响

 研究了乙烷添加对 Mo/HZSM-5 催化剂上甲烷芳构化反应性能的影响. 在所考察的反应条件下, 未观察到乙烷添加对甲烷转化的促进作用, 乙烷本身反而生成甲烷, 同时导致更高的积炭生成速率, 使 Mo/HZSM-5 催化剂更快地失活. 但添加乙烷加速了钼活性中心的形成, 缩短了芳构化反应的诱导期, 使苯的生成提前.     

Zn/HZSM-5催化剂上正/异丁烷芳构化反应性能研究

采用脉冲微反装置评价了纯正丁烷(原料I)、含有少量异丁烷的混合丁烷(原料Ⅱ)和富含异丁烷的混合丁烷(原料Ⅲ)在锌改性的纳米HZSM-5催化剂上的反应性能.通过红外吸附正丁烷羟基谱图,研究了Zn/HZSM-5催化剂的活性中心.结果表明,反应温度为550℃时,两种混合丁烷在催化剂上的转化率和芳构化选择性都远高于纯正丁烷.即异丁烷比例越高,反应效果越好,说明二者共存时,异丁烷在竞争反应中抑制了正丁烷的转化.另外,芳烃选择性均随Zn负载量的增加而增加.这是因为异丁烷在酸中心作用下脱氢生成叔碳正离子的能力高.而正丁烷的活化方式可能同时存在脱氢活化和脱甲基活化.因此,以工业碳四饱和烃为芳构化原料时,正丁烷和异丁烷可不必分离,直接以混合原料进行芳构化反应.     

稀土对HZSM—5上正己烷芳构化性能的影响

以正己烷为原料,在连续流动常压反应装置上考察了稀土改性HZSM－5沸石催化剂的芳构化和裂解性能,用红光谱,X射线衍射,X光电子能谱等研究了这些离子改性的沸石催化剂的表面性质,比较了机械混合法和浸渍法引入稀土对催化剂性能的影响,稀土可提高混合法制备的改性催化剂的芳构化性能,B酸中心是正已烷构化的活性中心,L酸中心则对正己烷的裂解起重要作用。     

Mo/HZSM-5催化剂上丙烷的芳构化反应

 采用浸渍法、机械混合法和水热法制备了Mo／HZSM－5分子筛催化剂,考察了Mo含量和在线反应时间对丙烷芳构化反应的影响,并以IR,XRD,NH3－TPD和XPS等表征手段研究了Mo物种对HZSM－5分子筛结构和酸性的影响．结果表明,水热法制备的催化剂丙烷芳构化活性最高,且具有较高的活性稳定性,在焙烧过程中Mo物种易在HZSM－5分子筛上分散,且比浸渍法更多地进入分子筛孔道内,并与分子筛产生强相互作用,使B酸中心减少,L酸中心增多．而浸渍法制备的催化剂的芳构化性能比相应的水热法催化剂低,活性稳定性较差,经焙烧后在分子筛外部形成结晶,进入孔道内的数量较少,对分子筛酸性的影响也低于水热法催化剂．     

Influence of Pretreatment Conditions on Methane Aromatization Performance of Mo／HZSM—5 and Mo—Cu／HZSM—5 Catalysts

Mo/HZSM-5 is a good catalyst for methane aromatization, and the reaction performance of Mo/HZSM-5 and Cu modified Mo/HZSM-5 catalysts under various pretreatment conditions has been studied. The results indicate that the catalyst presented a distinguished catalytic activity, benzene selectivity and a high stability when the bed temperature was raised in N2 atmosphere.     

Propane Aromatization over Mo／HZSM—5 Catalysts

Impregnation,mechanical mixing and hydrothermal treatment methods were used to introduce molybdenum species into the HZSM-5 zeolite ,the structure and surface acidity of the catalysts were studied by means of XRD,FT-IR ,NH3-TPD,TPR and XPS,The effects of Mo content and reaction time on stream on the aromatization of propane were investigated,It was found that the performance of the Mo/HZSM-5 catalst prepared by the hydrothermal treatment method was much better than that of the other two catalysts,For example ,under the reaction conditions of 823 K and 600h^-1, propance conversion and aromatics selectivity over the catalyst prepared by hydrothermal pretreatment could reach 89.17% and 78.56%,respectively,XRD and XPS results showed that the Mo species in the catalysts prepared by hydrothermal treatment were highly dispersed on the surface of the HZSM-5,and lartger amounts of them could penetrate into the HZSM-5 channel ,as compared with the other two kinds of catalysts,These factors may be responsibled for their high activities for propane aromatization,IR and NH3-TPD studies indicated that the number of Broensted acid centers decreased and the Lewis acid centers increased after Mo was introduced into the HZSM-5 zeolite.     

Propane Aromatization over Mo/HZSM-5 Catalysts

Impregnation, mechanical mixing and hydrothermal treatment methods were used to introduce molybdenum species into the HZSM-5 zeolite. The structure and surface acidity of the catalysts were studied by means of XRD, FT-IR, NH3-TPD, TPR and XPS. The effects of Mo content and reaction time on stream on the aromatization of propane were investigated. It was found that the performance of the Mo/HZSM-5 catalyst prepared by the hydrothermal treatment method was much better than that of the other two catalysts. For example, under the reaction conditions of 823 K and 600 h-1, propane conversion and aromatics selectivity over the catalyst prepared by hydrothermal pretreatment could reach 89.17% and 78.56%, respectively. XRD and XPS results showed that the Mo species in the catalysts prepared by hydrothermal treatment were highly dispersed on the surface of the HZSM-5, and larger amounts of them could penetrate into the HZSM-5 channel, as compared with the other two kinds of catalysts. These factors may be responsi     

Re/HZSM-5体系上的甲烷无氧芳构化反应

 与Mo／HZSM－5相比，Re／HZSM－5也是较好的甲烷无氧芳构化催\r\n化剂，其初活性较高，但随着反应的进行，催化剂失活的速率较快．通\r\n过NH3－TPD，H2－TPR和MASNMR等手段，对催化剂的酸性和分子筛骨架\r\n铝的变化以及铼物种的还原性能进行了研究．结果表明，催化剂酸性的\r\n在反应中起着重要的作用，但不同铼担载量的催化剂酸性的变化比较复\r\n杂，不同于Mo／HZSM－5体系．总的来看，并不是酸性越强或酸量越多\r\n，催化剂的催化性能就越好；催化剂的酸性和酸量都有一个最佳值．担\r\n载铼物种后，铼物种可与分子筛的骨架铝发生强烈的相互作用，最终导\r\n致骨架脱铝．Re／HZSM－5催化剂具有较高的低温活性，在较低温度下\r\n可被还原性气氛还原，且还原后的活性物种单一．     

改性纳米HZSM-5沸石催化剂上C5～C8混合烷烃的芳构化反应

在小型固定床反应器上研究了水蒸气钝化及过渡金属(Ni,Co,Cu,Zn)改性对调变纳米HZSM-5沸石催化剂上C5~C8混合烷烃芳构化反应的作用.采用NH3-TPD和Py-FT-IR方法表征了改性催化剂的表面酸性质,并与其催化芳构化性能进行了关联.结果表明,在450℃下进行水蒸气钝化能显著提高催化剂的芳构化选择性,减少甲烷和乙烷等低碳烷烃的生成;催化剂进一步用锌盐或铜盐溶液浸渍改性,可以显著提高催化剂的抗积炭失活能力.这是由于水蒸气钝化能适当减少沸石表面的酸量,降低酸强度,而铜、锌改性可进一步减少B酸中心,增加L酸中心,并与B酸中心协同作用形成具有脱氢活性的催化中心,从而影响混合烷烃的活化方式与芳构化路径.     

Studies on Mo／HZSM-5 Complex Catalyst for Methane Aromatization

The influence of adding Fe,Cr,Co,and Ga into 3%Mo/HZSM-5 catalyst on methane aromatization,and the influence of additives ratio on methane conversion,selectivity to hydrocarbons and coke,as well as distribution of aromatics were investigated.The experimental results showed that the addition of Fe,Cr,Co and Ga promoted the dehydrogenation and dissociation of methane.The results of NH3-TPD indicated that the acidity of HZSM-5 was changed by adding Fe and Co components,consequently the catalytic properties of Mo/HZSM-5 were changed.It was also revealed that strong acid sites were the center of methane aromatization.The results of XRD characterization showed that the crystallinity of Mo on ZSM-5 zeolite was increased after adding Fe,Co additives.     

Effects of Calcination Temperature on the Acidity and Catalytic Performances of HZSM-5 Zeolite Catalysts for the Catalytic Cracking of n-Butane

The acidic modulations of a series of HZSM-5 catalysts were successfully made by calcination at different treatment temperatures, i.e. 500, 600, 650, 700 and 800 ℃, respectively. The results indicated that the total acid amounts, their density and the amount of B-type acid of HZSM-5 catalysts rapidly decreased, while the amounts of L-type acid had almost no change and thus the ratio of L/B was obviously enhanced with the increase of calcination temperature (excluding 800 ℃). The catalytic performances of modified HZSM-5 catalysts for the cracking of n-butane were also investigated. The main properties of these catalysts were characterized by means of XRD, N2 adsorption at low temperature, NH3-TPD, FTIR of pyridine adsorption and BET surface area measurements. The results showed that HZSM-5 zeolite pretreated at 800 ℃ had very low catalytic activity for n-butane cracking. In the calcination temperature range of 500-700 ℃, the total selectivity to olefins, propylene and butene were increased with the increase of calcination temperature, while, the selectivity for arene decreased with the calcination temperature.The HZSM-5 zeolite calcined at 700 ℃ produced light olefins with high yield, at the reaction temperature of 650 ℃ the yields of total olefins and ethylene were 52.8% and 29.4%, respectively. Besides, the more important role is that high calcination temperature treatment improved the duration stability of HZSM-5zeolites. The effect of calcination temperature on the physico-chemical properties and catalytic performance of HZSM-5 for cracking of n-butane was explored. It was found that the calcination temperature had large effects on the surface area, crystallinity and acid properties of HZSM-5 catalyst, which further affected the catalytic performance for n-butane cracking.