共查询到18条相似文献,搜索用时 156 毫秒
1.
研究非共沸混合工质R32/R134a(质量比,25%/75%)在水平微尺度通道内流动沸腾换热规律。在各种工况下进行了非共沸混合工质R32/R134a在水平微尺度管道内流动沸腾换热的实验,考察了质量流量G、热流密度q、质量干度x对微尺度通道内流动沸腾换热系数的影响。研究表明:在热流密度、质量流量都较低的区域,对细管道,换热系数与热流密度的关联度较大;而对微管道,换热系数受影响的因素比较多,并在干度为0.6时出现"干涸"现象,使得换热系数急剧下降。在质量流量高的区域,对细管道,热流密度对换热系数的影响很小;而对微尺度管道,当干度为0.06时换热系数发生转变,随质量干度的增加先减小后增大,热流密度增大到一定的阶段后,换热系数不再随热流密度变化。 相似文献
2.
《低温与超导》2016,(12)
采用实验方法对制冷剂R134a在内径为1.98mm的水平光滑铜管内的流动沸腾换热特性进行研究。试验中,质量流速范围720~900kg/(m~2·s),热流密度范围19~28k W/m~2,系统压力0.7MPa和0.81MPa(饱和温度为26.8℃、31.4℃)和干度范围0~0.65。结果表明:质量流速对换热系数的影响较大,随着质量流速的增大而增大;在低干度区,热流密度对换热系数的影响较大,换热系数随干度的增加近似成单调增加;系统压力对换热系数也有明显的影响;将试验结果与Sun-Mishima公式和Liu-Winterton公式进行比较,发现试验结果与Sun-Mishima公式计算值吻合度较高,最大误差为14.1%。 相似文献
3.
为探究混合制冷剂R290/R134a(4/6)在水平微肋管中的沸腾传热特性,采用了CFD软件数值模拟的方法,对混合制冷剂R290/R134a(4/6)分别在外径为7 mm,长为500 mm的水平光滑管和微肋管中进行数值模拟与理论分析。分析了质量流量、热流密度,以及干度对混合制冷剂在水平微肋管中换热特性的影响。结果表明:两种管型的沸腾换热系数随质量流量、热流密度和干度的增大出现先增大后减小的趋势;热流密度对制冷剂沸腾换热系数的影响最大,在质量流量保持不变,改变热流密度的条件下,微肋管最大传热系数分别为光滑管的1.30、1.31、1.26倍;质量流量的增加提高了制冷剂的临界干度,光滑管与微肋管最大临界干度分别为0.57、0.63。 相似文献
4.
5.
对亚临界二氧化碳在带有微肋的微细通道内的蒸发换热特性进行了实验研究.实验段为长0.6 m,内径1.7 mm的八孔带0.16 mm高微肋的铝制扁管.实验中参数的变化为:蒸发温度1~15 ℃,质量流速100~300 kg/m2s,热流密度1.67~8.33 kW/m2,干度0.1~0.9.实验结果表明,二氧化碳在带有微肋的微细通道中的蒸发换热系数高于其在光滑微细通道内的换热.二氧化碳的流动蒸发换热系数主要受热流密度和蒸发温度的影响,基本上是换热系数随热流密度及蒸发温度的增加而增加,但同时临界干度前移及滞后,而质量流速对换热系数的影响较弱;压力损失随质量流速和热流密度的增加以及蒸发温度的降低而增加. 相似文献
6.
CO2在细径管内蒸发换热的实验研究 总被引:2,自引:1,他引:1
对CO2在细径管内蒸发换热特性进行了研究。试验管为内径4 mm长为0.5 m的光滑紫铜管。实验中参数变化范围为,蒸发温度1-15℃,质量流速100-300 kg/m2s,热流密度2-18 kW/m2,干度0.1-0.9。实验结果表明CO2 蒸发换热系数高于氟利昂类制冷剂,蒸发温度和热流密度对换热系数影响显著,而质量流速的影响相对较弱,传统制冷剂的换热系数关联式不适用于CO2;二氧化碳的压力损失随着热流密度和质量流速的增加而增加,随着蒸发温度的上升而减小,CO2压力损失小于氟利昂类制冷剂。 相似文献
7.
8.
9.
10.
针对超临界CO2空冷换热器中存在的非均匀传热问题,本文利用数值模拟计算了水平空冷翅片管中管壁热流分布规律及超临界CO2在非均匀冷却时的换热特性,同时分析了非均匀冷却工况下不均匀度、质量流量和浮升力等因素对换热规律的影响。结果表明:翅片管热流密度沿周向管壁位置呈现显著的不均匀分布,且不均匀度随风速增大而增大;超临界CO2非均匀冷却的平均换热系数在远离准临界点时高于均匀冷却,靠近准临界点时低于均匀冷却;非均匀冷却与均匀冷却的差异随不均匀度、质量流量增大而增大。CO2在准临界点处的非线性物性变化与浮升力作用是造成两者差异的主要原因。 相似文献
11.
Heat transfer in two-phase flow boiling of a dilute mixture of TiO2 nanoparticles in R141b base fluid in a smooth tube is investigated experimentally. Examining the obtained results reveals that enhancement of the convective heat transfer coefficient for the particle volume fractions of 0.01% and 0.03% in comparison with pure R141b is more pronounced for a higher volume fraction. The measured data also show that at higher vapor qualities, the improvement in heat transfer coefficient is greater. Moreover, the heat transfer coefficient decreases substantially with mass flux while an increase in saturation temperature leads to an improvement in this coefficient. 相似文献
12.
13.
实验研究了制冷剂-润滑油混合流体在内嵌泡沫金属圆管内流动沸腾的换热特性。泡沫金属为10ppi、90%孔隙率;制冷剂为R410A,润滑油为VG68,油浓度为0~5%。实验结果表明:纯制冷剂工况下,泡沫金属强化流动沸腾换热系数,换热系数提高30%~120%;含油工况下,泡沫金属只强化流动沸腾换热系数20%以下,在低质流密度或者高质流密度的高干度情况下出现恶化换热的情况。润滑油总是恶化制冷剂在内嵌泡沫金属圆管内流动沸腾的换热系数,换热系数最多恶化71%,且在低质流密度下对换热的恶化比在高质流密度工况下严重。 相似文献
14.
15.
采用RNG k-ε 湍流模型对超临界CO2流体在内径为4 mm, 长度2000 mm, 节距为10 mm, 曲率为0.1的水平螺旋管内的冷却换热进行了数值模拟.研究了质量流量、热流量以及压力对换热系数的影响, 并和超临界CO2在水平直管内的冷却换热进行了对比.研究结果表明, 超临界CO2在水平螺旋管内流动产生的二次流强于水平直管内的二次流, 前者的换热系数大于后者; 换热系数随质量流量的增加而增大; 在似气体区, 换热系数随着热流量的增加而增大, 而在似液体区, 热流量对换热系数几乎没有影响; 换热系数峰值点随着压力的升高而下降, 并向高温区偏移. 相似文献
16.
The effect of thermal environment on boiling heat transfer performance in a section of a horizontal tube bundle was investigated using R-113 as the working fluid. The in-line tube bundle has five columns and 27 rows with a pitch-to-diameter ratio of 1.3. Heal transfer coefficients obtained from the instrumented tube in the tube bundle with only one tube heated while the other tubes remained unhealed and with all the lubes in the bundle heated are reported for a range of heat flux, pressure, mass flow rate, and quality. The results showed that heat transfer coefficient of a tube in a heated bundle is slightly higher than that in an unhealed bundle, with the variation of heat transfer coefficient decreasing as heat flux, mass flow rate, or pressure increased. It was also found that higher quality would tend to improve the heat transfer. However, the effect of quality disappeared as heat flux, mass flow rate, and pressure increased. Based on the experimental data, the mechanism of the heat transfer augment due to thermal environment was analyzed. It was proposed that fluid agitation and thin liquid film formation are two main factors for a heated bundle to have better transfer performance than an unhealed bundle, 相似文献
17.
基于换热器几何结构参数以及流路布置等相同的3HP商用空调,在空调工况下,研究了相对湿度对R22替代制冷剂R407C、R410A、R32以及R290在蒸发器内的流动和传热性能的影响规律。研究表明:在一定的条件下,增加环境相对湿度,这五种制冷剂对应蒸发器换热量、压降和质量流量均增加,其中R407C蒸发器换热量最大,R290和R32蒸发器压降和制冷剂质量流量均小于R22蒸发器。在低湿度环境下(约20—30%相对湿度),显热换热占主导因素。随着相对湿度的增加,显然换热减少,潜热换热增强且起主导因素。在满足换热量的要求下,R290在协调压降与质量流量具有一定的优势且满足现行工质替代理念,可以作为现有商用空调的环保型替代工质。 相似文献
18.
Boiling heat transfer in a refrigerant R 21 flow in a microchannel heat sink is studied. A stainless steel heat sink with
a length of 120 mm contains ten microchannels with a size of 640×2050 μm at cross-section with a wall roughness of 10 μm.
The local heat-transfer coefficient distribution along the heat sink length is obtained. The ranges of parameters are: mass
flow from 68 to 172 kg/m2s, heat fluxes from 16 to 152 kW/m2, and vapor quality from 0 to 1. The maximum values of the heat transfer coefficient are observed at the inlet of microchannels.
The heat transfer coefficients decrease substantially along the length of channels under high heat flux conditions and, on
the contrary, change insignificantly under low heat flux condition. A comparison with the well-known models of flow boiling
heat transfer is performed and the range of applicability is defined. 相似文献