Flow injection direct spectrophotometric assay for the speciation of trace chromium(III) and chromium(VI) using chromotropic acid as chromogenic reagent

A new rapid and sensitive FI assay is reported for the simultaneous direct spectrophotometric determination of trace Cr(VI) and Cr(III) in real samples. The method is based upon the reaction of Cr(VI) with chromotropic acid (CA) in highly acidic medium to form a water-soluble complex (λ_max = 370 nm). Cr(III) reacts with CA only after its on-line oxidation to Cr(VI) by alkaline KIO₄. The determination of each chromium species in the sample was achieved by absorbance differences. The calibration curves were linear over the range 3-4000 μg l⁻¹ and 30-1200 μg l⁻¹ for Cr(VI) and Cr(III), respectively, while the precision close to the quantitation limit was satisfactory in both cases (s_r = 3.0% for Cr(VI) and 4.0% for Cr(III) (n = 10) at 10 and 50 μg l⁻¹ level, respectively). The method developed proved to be adequately selective and sensitive (c_L = 1 and 10 μg l⁻¹ for Cr(VI) and Cr(III), respectively). The application of the method to the analysis of water samples (tap and mineral water) gave accurate results based on recovery studies (93-106%). Analytical results of real sample analysis were in good agreement with certified values.     

Selective stopped-flow sequential injection method for the spectrophotometric determination of titanium in dental implant and natural Moroccan phosphate rock

The present work reports the first sequential injection (SI) method for the spectrophotometric determination of Ti(IV). The method is based upon the reaction of Ti(IV) with chromotropic acid (CA) in acidic medium to form a water-soluble complex (λ_max = 420 nm). The chemical and instrumental variables of the system that affected the reaction were studied. Selectivity was greatly enhanced using ascorbic acid. A linear calibration graph was obtained in the range 0.2-10.0 mg l⁻¹ Ti(IV) at a sampling frequency of 24 h⁻¹. The precision was satisfactory (s_r = 1.5% at 5.0 mg l⁻¹ Ti(IV), n = 12) and the 3σ limit of detection, c_L, was 0.7 mg l⁻¹ (n = 10). The developed method proved to be adequately selective and was applied successfully to the analysis of real samples (dental implant and natural Moroccan phosphate rock) giving accurate results based on recovery studies (98-105%).     

Selective determination of cyanides by gas diffusion-stopped flow-sequential injection analysis and an on-line standard addition approach

A highly selective sequential injection (SI) method for the automated determination of weak-acid-dissociable cyanides is reported. The analytical procedure is based on the on-line reaction of the analyte with ninhydrin in carbonate medium to form a coloured product (λ_max = 510 nm). Cyanides are removed from sample matrix by acidification through a gas-diffusion step incorporated in the SI manifold. The effect of instrumental and chemical variables was studied. By adopting an on-line standard addition protocol, the sensitivity of the proposed method was enhanced drastically, without affecting the determination range. The assay was validated in terms of linearity (up to 200 μg L⁻¹), limit of detection (c_L = 2.5 μg L⁻¹), limit of quantitation (c_Q = 7.5 μg L⁻¹), precision (s_r < 2.5% at 100 μg L⁻¹) and selectivity. High tolerance against critical species such as sulfides and thiocyanates was achieved. The applicability of the method was demonstrated by analyzing tap and mineral water samples at levels below the limits established by international E.U. and U.S. organizations. The percent recoveries were satisfactory in all cases, ranging between 94.2 and 103.6%.     

Analysis of salicylic acid based on the fluorescence enhancement of the As(III)-salicylic acid system

A new, simple and sensitive spectrofluorimetric method for the determination of salicylic acid (λ_ex = 315 nm, λ_em = 408 nm) using As(III) as a sensitizing reagent has been investigated by measuring the increase of fluorescence intensity of salicylic acid due to the complexation of As(III)-salicylic acid in presence of sodium dodecyl sulfate (SDS) 10⁻³ M. Under optimum conditions, a significant relationship was obtained between the fluorescence intensity and salicylic acid concentration. A linear calibration curve was obtained in the range 13.8-13812 μg l⁻¹ with product-moment correlation coefficient (R) 0.99985 and detection limit 4.2 μg l⁻¹. The R.S.D. is 2.35% (n = 5).The method was applied successfully to the determination of salicylic acid in human serum.     

Normal spectrophotometric and stopped-flow spectrofluorimetric sequential injection methods for the determination of alendronic acid, an anti-osteoporosis amino-bisphosphonate drug, in pharmaceuticals

A normal spectrophotometric and a stopped-flow (SF) spectrofluorimetric method have been developed and optimized for the determination of alendronic acid (ALD) in its pharmaceutical formulations. Both methods are automated using the sequential injection analysis (SIA) principle. The spectrophotometric assay is based on the reaction of the analyte with Cu(II) ions in acidic medium to form an UV-absorbing derivative (λ_max = 240 nm). The SF spectrofluorimetric method is based on the reaction of ALD with o-phthalaldehyde (OPA) in the presence of 2-mercaptoethanol at basic medium (λ_ex = 340 nm/λ_em = 455 nm). Linear calibration curves were obtained in the range 1.0-60.0 mg l⁻¹ ALD for the UV method, and in the range 0.13-10.0 mg l⁻¹ ALD for the SF spectrofluorimetric one. The sampling rates were 60 and 30 h⁻¹, respectively. The developed assays are critically compared and their advantages are discussed. Both methods were applied to the analysis of an ALD containing pharmaceutical formulation with satisfactory accuracy and precision.     

Determination of the antidepressant paroxetine and its three main metabolites in human plasma by liquid chromatography with fluorescence detection

A high-performance liquid chromatographic method has been developed for the determination in human plasma of the specific serotonin reuptake inhibitor (SSRI) antidepressant paroxetine and its three main metabolites (M1, M2, M3). Fluorescence detection was used, exciting at λ = 294 nm and monitoring emission at λ = 330 nm for paroxetine (λ_exc = 280 nm, λ_em = 330 nm for M1 and M2; λ_exc = 268 nm, λ_em = 290 nm for M3). Separation was obtained on a reversed-phase C18 column using a mobile phase composed of 66.7% aqueous phosphate at pH 2.5 and 33.3% acetonitrile. Imipramine (λ_exc = 252 nm, λ_em = 390 nm) was used as the internal standard. A careful pre-treatment of plasma samples was developed, using solid-phase extraction with C8 cartridges (50 mg, 1 mL). The calibration curves were linear over a working range of 2.5-100 ng mL⁻¹ for paroxetine and of 5-100 ng mL⁻¹ for all metabolites. The limit of detection (LOD) was 1.2 ng mL⁻¹ for PRX and 2.0 ng mL⁻¹ for the metabolites. The method was applied with success to plasma samples from depressed patients undergoing treatment with paroxetine. Hence, the method seems to be suitable for the therapeutic drug monitoring of paroxetine and its main metabolites in depressed patients’ plasma.     

Sensitive sequential injection determination of naproxen based on interaction with beta-cyclodextrin

A sensitive sequential injection analysis (SIA) methodology for the fluorimetric determination of naproxen is proposed. The developed automatic analytical procedure is based on the complexation of naproxen with β-cyclodextrin (β-CD) yielding an enhanced fluorimetric signal (λ_ex = 280 nm, λ_em = 356 nm).Linear calibration plots were obtained for naproxen concentrations up to 1 × 10⁻⁵ mol l⁻¹. The developed methodology exhibited a good precision, with a R.S.D. < 2.1% (n = 15). The detection limit of the determination was 1.9 × 10⁻⁷ mol l⁻¹ with a sampling rate of about 70 h⁻¹. The automatic method was applied to the determination of naproxen in pharmaceutical formulations. The obtained results were compared with those furnished by the reference procedure and the relative deviations were lower than 3.6%. No interference was found from the excipients usually used in solid pharmaceutical formulations.     

Flow-injection investigation of the chemiluminescent reaction of bis(2,4,6-(trichlorophenyl)oxalate) with free chlorine

This work investigated the chemiluminescent reaction of free chlorine with bis(2,4,6-(trichlorophenyl)oxalate) (TCPO) in the presence of 9,10-diphenylanthracene in acetonitrile/water medium, with analytical application for free chlorine in tap water. In the absence of free chlorine, the background signal increased with the pH and the chemiluminescence emission showed strong dependence with the sample acidity. A flow injection analysis system, for free chlorine determination, was developed. The linear range for free chlorine was (0.2-3.0)×10⁻⁵ mol l⁻¹. Chloramine 1.0×10⁻⁵ mol l⁻¹ and chlorite 1.0×10⁻⁶ mol l⁻¹ also enhanced the chemiluminescence intensity.     

Highly sensitive spectrofluorimetric kinetic determination of ultratrace amounts of vanadium(V) based on the oxidation of 1,8-diaminonaphthalene by bromate

A highly sensitive catalytic quenching spectrofluorimetric method was described for the determination of V(V) based on its catalytic effect on the oxidation of 1,8-diaminonaphthalene by potassium bromate with Tiron as an activator in weakly acidic medium and the reaction mechanism was investigated. The reaction was followed spectrofluorimetrically by measuring the fluorescence intensity of 1,8-diaminonathphlene (DAN) (λ_ex=356 nm, λ_em=439 nm) at a fixed time of 5 min from initiation of the reaction. Under the optimum conditions, vanadium(V) can be determined in the range 0.05-50.0 ng ml⁻¹ with a S.D.=0.024 for 15 times measurements. The detection limit of the method was down to 0.0088 ng ml⁻¹ and the catalytic reaction activation energy was found to be 43.92 kJ mol⁻¹. The proposed method was tested for the determination of vanadium(V) in rice and natural water samples.     

A novel spectrofluorimetric method for the ultra trace analysis of nitrite and nitrate in aqueous medium and its application to air, water, soil and forensic samples

A highly sensitive and virtually specific method has been developed for the trace and ultra trace 5 ng ml⁻¹-1 μg ml⁻¹ fluorimetric analysis of nitrite. The method is based on the quenching action of nitrite on the native fluorescence of murexide (ammonium purpurate) [λ_ex=349.0 nm, λ_em=444.5 nm] in the acid range of 0.045-0.315 (M) H₂SO₄. The method is very precise and accurate (S.D.=±0.4877 and R.S.D.=0.4878% for the determination of 0.1 μg ml⁻¹ of nitrite in 11 replicates). Relatively large excesses of over 35 cations and anions do not interfere. The proposed technique has been successfully applied for the determination of nitrite and nitrate in ground water, surface water and sea water, nitrite in soil and nitrate in forensic samples. The method has also been extended for the analysis of NO_x in air.     

Post-column terbium complexation and sensitized fluorescence detection for the determination of norepinephrine, epinephrine and dopamine using high-performance liquid chromatography

Terbium sensitized fluorescence was used as a post-column detection system to develop a simple, sensitive and rapid high-performance liquid chromatographic method for the simultaneous determination of catecholamines norepinephrine (NE), epinephrine (E) and dopamine (DA).Catecholamines were separated by an ion-pair reversed-phase chromatography on a BDS-Hypersil analytical column with a mobile phase of methanol and 50 mmol l⁻¹ acetate buffer (pH 4.7) containing 1.1 mmol l⁻¹ SOS and 0.11 mmol l⁻¹ EDTA (15+85 v/v).Catecholamines and the internal standard (3,4-dihydroxybenzylamine, DHBA) were post-column derivatized by the addition to the eluent of an alkaline solution containing a stoichiometric mixture of terbium(III) chloride and EDTA. Fluorescence detection (λ_ex=300 nm, λ_em=545 nm) is based on the sensitization of terbium ion fluorescence after complexation with catecholamines.The chemical compatibility between the eluent and the post-column reagent was studied and the analytical characteristics of the method were established. Detection limits found were 1.0×10⁻⁸, 4.0×10⁻⁸ and 7.0×10⁻⁸ mol l⁻¹ for NE, E and DA, respectively. The method has been successfully applied to the determination of catecholamines in urine samples after solid-phase extraction (SPE) pre-treatment. Recoveries from urine spiked with NE (4.0×10⁻⁷, 2.0×10⁻⁶ and 4.0×10⁻⁶ mol l⁻¹), E (8.2×10⁻⁸, 4.1×10⁻⁷ and 8.2×10⁻⁷ mol l⁻¹) and DA (1.0×10⁻⁶, 5.0×10⁻⁶ and 1.0×10⁻⁵ mol l⁻¹) varied from 98 to 100% (mean=99.3%), from 106 to 107% (mean=106.3%) and from 98 to 101% (mean=99.3%), respectively. The between-run precision (relative standard deviation, R.S.D.) for the method for three urine samples at different concentration levels of each catecholamine varied from 3.6 to 7.0%.     

Solvent extraction flow-injection manifold for the simultaneous spectrophotometric determination of free cyanide and thiocyanate ions based upon on-line masking of cyanides by formaldehyde

This study reports a sensitive solvent extraction flow-injection (FI) method for the simultaneous spectrophotometric determination of free cyanide and thiocyanate in human saliva and pralidoxime solutions. Cyanide and thiocyanate form colored (λ_max=540 nm) ternary complexes with copper and 2,2′-dipyridyl-2-quinolylhydrazone (DPQH) that are extractable into chloroform. The determination of thiocyanates in the presence of cyanides is accomplished after on-line masking of the latter with formaldehyde through a binary inlet static mixer (BISM). Total thiocyanates and cyanides are determined in a second run, without the use of the masking agent. The proposed method allows the determination of the analytes in the range of 0-4 mg l⁻¹ thiocyanates and 0-3 mg l⁻¹ cyanides, with the 3σ detection limits being 0.007 and 0.004 mg l⁻¹, respectively. The precision of the method (s_r<1.0% at 1 mg l⁻¹ CN⁻ or SCN⁻, n=12 in both cases) and the sampling rates were quite satisfactory (60 injections per hour). The method was applied to the analysis of human saliva and pralidoxime solutions and gave recoveries in the range of 98.0-102.2% for both analytes whereas the mean relative error was e_r=1.7%.     

Fluorimetric determination of aminocaproic acid in pharmaceutical formulations using a sequential injection analysis system

A sequential injection analysis (SIA) methodology for the fluorimetric determination of aminocaproic acid in pharmaceutical formulations is proposed. The developed analytical procedure is based on the derivatisation reaction of the aminocaproic primary amine with o-phthalaldehyde (OPA) and N-acetylcysteine (NAC) and fluorimetric detection of the formed product (λ_ex = 350 nm; λ_em = 450 nm). The implementation of a SIA flow system allowed for the development of a simple, fast and versatile automated methodology, which exhibits evident advantages regarding the US Pharmacopoeia 24 (USP 24) reference procedure. By combining the SIA time-based sample insertion with a subsequent zone sampling approach, which permitted to select for detection of a well-defined sample zone, it was possible to implement an on-line dilution strategy that enabled the expansion of the analytical working range of the methodology, and thus its application in dissolution studies, without manifold re-configuration.Linear calibration plots were obtained for aminocaproic acid concentrations up to 6 × 10⁻⁵ mol l⁻¹. The developed methodology exhibit a good precision, with a R.S.D. < 2.0% (n = 15) and the detection limit was 2.5 × 10⁻⁷ mol l⁻¹. The obtained results complied with those furnished by the reference procedure with a relative deviation lower than 1.2%. No interference was found.     

Artificial neural networks study of the catalytic reduction of resazurin: stopped-flow injection kinetic-spectrophotometric determination of Cu(II) and Ni(II)

An artificial neural network (ANN) procedure was used in the development of a catalytic spectrophotometric method for the determination of Cu(II) and Ni(II) employing a stopped-flow injection system. The method is based on the catalytic action of these ions on the reduction of resazurin by sulfide. ANNs trained by back-propagation of errors allowed us to model the systems in a concentration range of 0.5-6 and 1-15 mg l⁻¹ for Cu(II) and Ni(II), respectively, with a low relative error of prediction (REP) for each cation: REP_Cu(II) = 0.85% and REP_Ni(II) = 0.79%. The standard deviations of the repeatability (s_r) and of the within-laboratory reproducibility (s_w) were measured using standard solutions of Cu(II) and Ni(II) equal to 2.75 and 3.5 mg l⁻¹, respectively: s_r[Cu(II)] = 0.039 mg l⁻¹, s_r[Ni(II)] = 0.044 mg l⁻¹, s_w[Ni(II)] = 0.045 mg l⁻¹ and s_w[Ni(II)] = 0.050 mg l⁻¹. The ANNs-kinetic method has been applied to the determination of Cu(II) and Ni(II) in electroplating solutions and provided satisfactory results as compared with flame atomic absorption spectrophotometry method. The effect of resazurin, NaOH and Na₂S concentrations and the reaction temperature on the analytical sensitivity is discussed.     

A novel application of immobilization on membranes for the separation and spectrofluorimetric quantification of amiloride and furosemide in pharmaceutical samples

A new, simple and highly sensitive method for spectrofluorimetric determination of amiloride (AMI) and furosemide (FUR) in pharmaceuticals is presented. The proposed method is based on the separation of AMI from FUR by solid-phase extraction using a nylon membrane, followed by spectrofluorimetric determination of both drugs, on the solid surface and the filtered aqueous solution, respectively. AMI shows low native fluorescence, but its separation-preconcentration by immobilization (solid-phase extraction) on nylon membrane surface provides a considerable enhancement in fluorescence intensity. The fluorescence determination is carried out at λ_ex = 237, λ_em = 415 nm for FUR; and λ_ex = 365, λ_em = 406 nm for AMI. The calibration graphs are linear in the range 3.20 × 10⁻⁴ to 0.8 μg mL⁻¹and 1.33 × 10⁻³ to 4.0 μg mL⁻¹, for AMI and FUR, respectively, with a detection limit of 9.62 × 10⁻⁵ and 4.01 × 10⁻⁴ μg mL⁻¹ (S/N = 3). The commonly found excipients in commercial pharmaceutical formulations do not interfere. The developed method is successfully applied to the determination of both drugs in pharmaceutical formulations.     

Rapid spectrophotometric determination of fosfestrol following on-line hydrolysis by alkaline phosphatase using flow injection and chasing zones

A new flow injection (FI) method is reported for the spectrophotometric determination of fosfestrol (diethyl-stilbestrol (DES) diphosphate) in pharmaceutical formulations. The proposed method is based on the on-line hydrolysis of the analyte by alkaline phosphatase (Al-Pase) using a “chasing zones” FI manifold. The orthophosphate ions, thus, generated are determined spectrophotometrically (λ_max=690 nm) using the molybdenum blue approach. The chemical and FI variables affecting the enzymatic reaction were investigated. The proposed method is very precise (s_r=1.1% at 1×10⁻⁴ mol l⁻¹ fosfestrol, n=12), fast (allowing up to 40 samples h⁻¹ to be analyzed) and has a determination range of 2×10⁻⁵ to 2×10⁻⁴ mol l⁻¹, with a satisfactory 3σ detection limit of 5×10⁻⁶ mol l⁻¹. The method was shown to provide accurate determinations of the fosfestrol concentration in a pharmaceutical formulation, giving relative errors, e_r, of +0.6 and −0.5% compared to the value stated by the supplier (Asta Medica Inc.) and the concentration derived using a method recommended by the United States Pharmacopoeia XXI, respectively. In addition, the average recoveries of known amounts of the analyte ranged between 99.2 and 101.2%.     

Determination of melamine in different milk batches using a novel chemosensor based on the luminescence quenching of Ru(II) carbonyl complex

A novel, simple, sensitive and precise spectrofluorimetric method was developed for measuring the melamine concentration in different milk batch samples. The method was based upon measuring the quenching of the luminescence intensity of the produced yellow colored ruthenium^(II) carbonyl complex of the general formula [Ru(CO)₂(L)] (where L = anion of tetradentate Schiff base). The Ru^(II) complex exhibited characteristic luminescence band in the visible region. The remarkable quenching of the luminescence intensity of [Ru(CO)₂(L)] complex by various concentrations of melamine was successfully used as a chemosensor for the assessment of melamine in different milk samples at λ_ex = 400 nm and pH 7.4 in DMSO with a linear dynamic range 1.0 × 10⁻⁶ to 3.0 × 10⁻⁹ mol L⁻¹ and lower detection limit (LOD) and quantification detection limit (QOD) of 3.3 × 10⁻¹⁰ and 1.0 × 10⁻⁹ mol L⁻¹, respectively.     

Sensitive fluorimetric flow injection analysis for fluoride ion with a novel reagent, 2',7'-dichlorofluorescein di-tert-butyldimethylsilyl ether

A novel reagent, 2′,7′-dichlorofluorescein di-tert-butyldimethylsilyl ether (FCl₂TBS), was synthesized for fluoride ion and used for a sensitive fluorimetric flow injection analysis by detecting the recovery of fluorescence due to cleavage of Si-O bond. Four kinds of fluorescein di-tert-butyldimethylsilyl ether (FTBS) analogues were synthesized and FCl₂TBS was the best. By introducing chlorine to FTBS, stability of the reagent, reactivity and the baseline signals were improved. The FIA system was three lines. The sample solution (aqua medium) was injected in the carrier solution (water) and merged with the reagent solution (2.0 × 10⁻⁵ M FCl₂TBS acetone solution), then mixed with phosphate buffer solution (pH 7.5). The fluorescence intensities were measured at λ_ex 503 nm and λ_em 527 nm. The calibration graph had linear relationship between (1.0-50.0) × 10⁻⁶ M and the determinable limit was 1.0 × 10⁻⁶ M. The relative standard deviation of 12 measurements with 1.0 × 10⁻⁵ M F⁻ solution was 1.0% and the sample throughput was 13 h⁻¹. The developed method was successfully applied to river and tap water samples.     

Sensitized extraction spectrophotometric determination of Hg(II) with dithizone after its flotation as ion-associate using iodide and ferroin

This paper describes a simple and highly selective method for the separation, preconcentration and spectrophotometric determination of extremely low concentration of mercury. The method is based on the flotation of an ion-associate of HgI₄²⁻ and ferroin between aqueous and n-heptane interface at pH 5. The ion-associate was then separated and treated with ammonia and dithizone solutions to extract only the mercury chelate with CH₂Cl₂. The measurement is feasible when the volume of the water sample containing Hg(II) was varied over 50-800 ml. Beer's law was obeyed over the concentration range of 8 × 10⁻⁹ to 1.6 × 10⁻⁷ mol l⁻¹ with an apparent molar absorptivity of 6.53 × 10⁶ l mol⁻¹ cm⁻¹ for a 500 ml aliquot of the water sample. The detection limit (n = 7) was 5.0 × 10⁻¹⁰ mol l⁻¹ and the R.S.D. (n = 5) for 8.0 × 10⁻⁷ mol l⁻¹ of Hg(II) was 3.7%. A notable advantage of the method is that the determination of Hg(II) is free from the interference of almost all cations and anions found in the environmental and waste water samples. The determination of Hg(II) in tap, synthetic sea water and human hair samples was carried out by the present method and cold vapor atomic absorption spectrometry (CV-AAS). The results were satisfactorily comparable so that the applicability of the proposed method was confirmed to the real samples.     

Determination of carbon dioxide in gaseous samples by gas diffusion-flow injection

A gas diffusion-flow injection system was developed for the determination of carbon dioxide in gaseous samples. The calibration was based on the use of either gaseous carbon dioxide or aqueous sodium carbonate standards. Gaseous carbon dioxide samples and gaseous or aqueous standards were injected directly into a donor stream of 1.0×10⁻⁴ M H₂SO₄. In the gas diffusion unit, carbon dioxide diffused through a PTFE membrane into an acceptor stream containing a mixed acid/base indicator. The absorbance of the acceptor stream was monitored spectrophotometrically at 554 nm. The calibration plot was linear over the range of 5.00×10² to 1.27×10⁴ μl l⁻¹ with a sample throughput of 28 h⁻¹ and 3.2% R.S.D. ([CO₂]=2.37×10³ μl l⁻¹, n=12). The detection limit was determined as 2.50×10² μl l⁻¹. The flow system was successfully applied to the analysis of several natural gaseous samples and the headspace of milk containers during storage. The flow injection results were found to be statistically indistinguishable at the 95% confidence level from those obtained by gas chromatography using thermal conductivity detection.