聚合物脊形光波导的变分有效折射率法分析

聚合物脊形光波导是聚合物集成光电子器件的重要构成单元.利用有效折射率法计算聚合物脊形光波导的横向折射率分布及有效折射率,将各区域中的光场分布近似用分段函数表达.基于导模满足的标量波动方程,利用变分法确定变分参量,以求得准确的横向光场分布.对聚合物脊形多模光波导基模和高阶模的色散特性与横向场分布进行分析,研究了波导结构参数对色散特性的影响,计算出TM基模和高阶模的光场分布,得出了聚合物脊形光波导的单模传输条件.研究表明,该方法计算量小、精度高,对聚合物光电子器件中脊形光波导的理论分析与设计优化提供了简单高效的方法.     

基于离子交换条波导的生物溶液浓度传感研究

提出并实施了一种实验推定离子交换单模条波导折射率分布的新方法,给出扩散系数可用常量等效的离子交换条件,导出了条波导离子交换制备过程的两维扩散方程的一般解,拟合推定了离子交换条波导的折射率分布.多波长测试的折射率色散通过引入玻璃色散关系解决,样品测试中表征导模吸收损耗的传播常量虚部由KK变换确定.在此基础上,试制了光纤-条波导-光纤一体化传感器结构,验证实测了多种不同浓度的葡萄糖溶液,最低检测限为0.1 μM,实现了低浓度微量测试,验证了条波导传感机制的有效性.     

离子交换KTP晶体光波导及其各向异性波导性能研究

采用离子交换法制备了Ｒｂ：ＫＴＰ晶体光波导，在不同波长的耦合光下测量了ＴＥ和ＴＭ偏振波导模式的有效折射率，拟合了波导层折射率的余误差函数分布，证明了波导折射率增量的各向异性，给出了其色散关系；最后计算并讨论了Ｒｂ：ＫＴＰ波导的扩散特性。     

掺铒玻璃波导放大器中抽运光信号光重叠因子分析

通过分析掺铒(Er3 )玻璃波导放大器(EDWA)的放大增益机理,提出抽运光与信号光光模场分布之间的归一化重叠积分因子(Γ),并引入到掺铒波导放大器增益模拟计算中,使理论模型更切合实际。以Ag -Na 二次离子交换工艺制作的具有埋入型渐变折射率分布的掺铒波导放大器为例,采用数值方法模拟了条形波导截面上的二维折射率分布及抽运光、信号光的光模场分布。计算了不同工艺参量设置下的Γ大小,讨论Γ对放大器增益的影响。结果显示,在二次离子交换制作过程中设置适当工艺参量优化折射率分布,能有效改善波导中抽运光与信号光光模场分布之间的重叠因子,提高掺铒波导放大器的增益。计算结果显示,在一定条件下,Γ从0.5增至0.8,每厘米长度掺铒波导放大器的放大增益可提高近1.5 dB。     

Ti：LiNbO3光波导导模的场分布

给出了Ti扩散LiNbO_3条波导任意阶导模场分布的试探解.通过变分法分析,不但可以合理地确定其中的待定参数,而且也得到了相应导模传播常数的近似值.与扩展的有效折射率方法比较:这种解不但在函数形式上简单,待定常数确定方便,而且具有精度高的优点.还可以得到等效一维波导折射率分布的解析表达式.     

气相质子交换LiTaO3光波导及其特性

本文利用苯甲酸气相质子交换技术制备了LiTaO3光波导，测量了Z-切LiTaO3光波导的参数（交换深度d和表面折射率增量△nc）和X-切LiTaO3光波导的红外吸收谱，给出了光波导层的折射率分布，并与液相质子交换热退火光波导的结果进行了比较。实验结果表明：非寻常折射率分布与热退火液相质子交换方法制备的LiTaO3光波导基本相近，但表面非寻常折射率增量（△nc）更大，其折射率分布更接近于高斯型。     

K-Na离子交换单模平面波导的制备及其表征

通过K-Na离子交换技术制备了多模玻璃平面波导.采用棱镜耦合技术测量了波导的有效折射率,用IWKB方法拟合得到K-Na离子交换波导的折射率分布符合高斯分布,由色散曲线得到单模波导的制备条件(即扩散深度范围),从而得出单模波导的离子交换时间范围,制备出单模波导,并通过求解WKB色散方程得出单模波导的表面折射率.用普通数码相机,通过对离子交换平面玻璃光波导传输线进行数字成像,根据传输线上的光强分布拟合出光强传输衰减曲线,计算出单模波导的传输损耗大约为0.4 dB/cm.     

后处理对离子交换磷酸盐玻璃平面光波导的影响

研究了退火和二次离子交换对Er3+/Yb3+共掺的磷酸盐玻璃平面光波导传输特性的影响。在退火过程中，由于热效应和波导层Ag+离子的浓度差使得Ag+离子重新分布；随着退火时间的延长和温度的升高，光波导模式数目逐渐增加，波导层深度加深，且波导表面折射率与玻璃基质折射率差减小，退火扩散深度与退火时间的平方根成正比。电子探针结果显示在二次离子交换后形成了掩埋式的光波导，Ag+离子浓度接近二次方分布，而掩埋式的光波导有助于降低光波导的传输损耗。     

He^＋离子注入LiNbO3晶体波导的制备及其性能研究

报道了液氮温度下Ｈｅ＾＋离子注入ＬｉＮｂＯ３波导的制备，采用棱镜耦合法测量了波导退火前后导模的有效折射率，计算了波导层折射率的分布和晶体中Ｈｅ＾＋离子的射程分布和损伤分布，两者吻合得较好。     

聚合物脊形光波导TM模色散特性的偏振修正

有机聚合物脊形光波导的色散特性对聚合物光子学器件性能具有重要影响.本文利用标量变分理论计算脊形光波导的有效折射率,其用到的近似光场分布运用变分有效折射率法获得.考虑折射率分布的横向变化,基于导模满足的矢量波动方程,利用微扰法对标量变分理论所得有效折射率进行偏振修正,求得精度更高的色散特性.对聚合物多模脊形光波导基模和高阶模的色散特性进行分析,研究了波导结构参数对色散特性的影响,分析了单模波导TM、TE基模的偏振色散特性.研究结果表明,运用本征方程分析TM模的色散特性误差大,必须加以修正;而对于TE模,其误差相对较小.     

一种简单精准的渐变折射率分布光波导分析方法

渐变折射率分布的光波导分析对光波导器件的设计和研究至关重要, 近年来已提出了多种分析方法, 然而在简便性或准确性上都存在着不足. 为此, 提出了一种分析渐变折射率分布光波导的方法, 能够结合现有的Wentzel-Kramers-Brillouin近似法和离散化的波动方程, 构建模场分布, 再结合变分运算方程和修正的模式本征方程, 计算出较为精确的有效折射率. 与其他分析方法相比, 该方法较为简单, 而且有一定的精度.     

Investigation of a UV-laser generated planar polymeric waveguide directly and after five years of preparation using an interferometric method

Polymeric integrated-optical waveguides were prepared in a planar chip using UV-laser lithographic method. Five waveguide samples were irradiated by an excimer laser of wavelength 248 nm with different irradiation parameters (fluence and irradiation doses). Using Mach–Zehnder interferometer, the refractive index depth profiles of these samples are determined in two cases, directly and five years later of preparation. A crucial change of refractive indices profiles has been recorded after five years of preparation. In the first case we got double region waveguides fitted a Gaussian shape, while in the second one we observe a single region waveguide which has exponential shape. The photochemical reactions responsible for these changes in the two cases are demonstrated. This is quite important when such waveguides are used in the applications. Also it was interesting to investigate the aging impact on mode field distributions and the effective mode indices. The mode parameters are determined based on a theoretical model and the experimentally obtained data. The results show a notable change in the mode field distributions and the propagation coefficients as influence of aging.     

A simple variational analysis of diffused channel waveguides

The variational analysis of Ti:LiNbO₃ strip waveguides is resolved into two related one-dimension problems, which provides a new iterative approach for the calculation of the mode parameters and the propagation constant. The analytical expressions of the local effective index profiles can be obtained from the variational analysis. The parameters of four trial solutions for the fundamental mode in a diffused-channel waveguide have been determined by using the present method. Comparison with results using the effective method shows that these four approximate expressions are accurate enough. It is also shown that this method converges very quickly and is suitable for both diffused channel waveguides and optical waveguides with rectangular cross-section.     

Design and numerical analysis for low birefringence silica on silicon waveguides

A new fabrication technology for three-dimensionally buried silica on silicon optical waveguide based on deep etching and thermal oxidation is presented.Using this method,a silicon layer is left at the side of waveguide.The stress distribution and effective refractive index are calculated by using finite element method and finite different beam propagation method,respectively.The results indicate that the stress of silica on silicon optical waveguide fabricated by this method can be matched in parallel and vertical directions and stress birefringence can be effectively reduced due to the side-silicon layer.     

Rib waveguide analysis by theimaginary-distance vectorialbeam-propagation method based on Yee's mesh

The effective index and the mode profile of rib waveguides are calculated using the vectorial beam-propagation method using the imaginary-distance procedure. Yee's mesh originally developed in the finite-difference time-domain method is employed to discretize a waveguide geometry. The refractive index at the interface between two different media is determined by Ampere's circuital law. The field discontinuities at the interface and singularities at the corners of the waveguide are clearly displayed.     

Research on the influence of fabrication parameters on the performance of buried ion-exchanged glass waveguides using the variational method

The variational method is proposed to analyze the influence of the fabrication parameters on the performance of buried K⁺–Na⁺ ion-exchanged Er³⁺–Yb³⁺ ions co-doped glass waveguide. The unknown parameters of the Hermite–Gaussian functions as the trial field distribution are determined based on the scalar variational principle. It is demonstrated that the results calculated in this paper agree with those measured in the experiment. The mode dimensions, the effective refractive index, and the overlap factor as the functions of the fabrication parameters are investigated. These results of the variational analysis are useful for the design and optimization of Er³⁺–Yb³⁺ ions co-doped waveguides.     

质子注入掺镱磷酸盐玻璃平面光波导的近红外特性

在能量为(0.5+0.55)MeV和剂量为(1.0+2.0)×10^16 ions/cm^2的条件下,通过氢离子注入制备了掺Yb^3+磷酸盐玻璃波导,并研究了该波导在近红外波段的特性.棱镜耦合法测量的离子注入波导的导模的有效折射率与反射计算法计算的有效折射率基本吻合.通过模拟辐照引起的空位分布,探讨了离子注入平面波导的形成理论.利用FD-BPM对波导中的传播模式进行了模拟,结果表明高能量的氢离子注入掺Yb 3+磷酸盐玻璃能够制备出近红外波导结构.