气相苯在TiO2光催化剂上吸附常数和光催化反应常数测定

采用溶胶-凝胶法制备TiO2光催化剂以及掺杂Fe3 和Ce3 的TiO2光催化剂,进行间歇式光催化降解气相苯动力学实验,基于光催化Langmuir-Hinshelwood反应动力学模型(L-H模型),测定气相苯在3种光催化剂上的降解动力学常数和吸附平衡常数.根据光催化降解气相苯实验动力学曲线和L-H模型,估算出TiO2、Fe3 /TiO2和Ce3 /TiO2光催化剂光催化降解苯的反应速率常数k和Langmuir吸附常数K分别为0.5247g/m3·min、1.523g/m3·min、1.010g/m3·min和8.605×10-2m3/g、2.390×10-2m3/g、3.928×10-2m3/g.掺杂Fe3 和Ce3 可明显提高光催化剂光催化降解苯的反应速率常数k,其中Fe3 /TiO2,的反应速率常数k最大.     

循环流动固定床光催化反应器动力学数学模拟

以甲基橙为模型反应物,研究了连续循环固定床光催化反应器的动力学过程.根据光催化氧化过程特点,分析并建立了准一级反应动力学方程,对该反应系统的动力学过程进行动态数学模拟,用四阶Runge-Kutta法进行数值计算,结果表明数学模拟与实验数据相吻合.在该光催化反应体系中,处理量增加时实际反应速率常数k基本不变,而表观反应速率常数kapp变小,二者之间关系与反应器体积对处理量体积比（γ）密切相关;反应速率常数受起始浓度影响很大,在15～150 μmol•L－1浓度范围内,lnk=－0.48ln[c0]＋1.42;反应速率常数与光强的关系为k∝I0.5;反应速率常数受溶液pH值的影响也很大.     

几种典型有毒有机污染物的光催化降解研究

本文研究了氯代苯酚和苯胺类化合物的光催化降解,探讨了这些有机污染物分子的氯取代和化合物毒性与光催化降解之间的关系.研究表明,氯代苯酚和苯胺类化合物的光催化降解均符合表观一级反应动力学模型.有机物分子中氯取代基的引入加快了化合物的光催化降解,且反应速率随氯取代基个数的增多而增大.光催化降解的表观速率常数与正辛醇-水分配系数之间存在有较好的线性关系:logk=alogKow+b,该模型可以用于有机污染物的光催化降解性预测.     

TiO2光催化降解苯和甲苯的动力学研究

利用溶胶-凝胶法制备了粒径约为13nm、晶型为锐钛矿相和金红石相混晶的TiO2光催化剂,并利用此催化剂对挥发性有机污染物苯和甲苯进行了光催化降解研究,对不同的催化剂用量、光源、污染物的初始浓度以及氧气对光催化反应速率的影响进行了研究。结果表明,光催化降解甲苯和苯的反应均符合假一级动力学方程,光强与光催化降解甲苯的反应的速率常数之间呈指数关系,光波长对光催化降解苯的影响也很显著;随着甲苯和苯初始浓度的增加,光催化反应速率常数降低;氧气加快了光催化降解甲苯和苯的速率;对于光催化降解初始浓度为37.6μmol/L的甲苯而言,催化剂的最佳使用量为0.30g,对于光催化降解初始浓度为9.0μmol/L的苯来说,催化剂的最佳用量为0.10g。     

光催化降解污染物制氢反应与原位红外表征

研究了在Pt/TiO2悬浮体系中单组分和双组分污染物为电子给体光催化分解水制氢反应. 比较了污染物甲醛、甲酸和草酸为电子给体光催化放氢反应效率，发现其活性为：草酸 >甲酸 >甲醛.原位ATR（衰减全反射）红外研究结果表明，光催化放氢活性与污染物吸附特性有关.还研究了草酸与甲酸双组分污染物体系的光解水放氢和污染物降解动力学，发现总的放氢和污染物降解速率与污染物组分在TiO2表面的吸附强度和溶液浓度有关.污染物在TiO2表面的竞争吸附决定了反应动力学.原位ATR-IR方法研究双组分混合物体系的吸附，直观地证实了上述结果.     

NO2^—离子的光催化反应

对NO2离子的TiO2光催化反应研究发现，该光催化反应用于消除NO2离子效果显著．反应的动力学研究表明，NO2离子的TiO2光催化反应是一个较复杂的多步反应，其中，NO2离子在TiO2催化剂表面的光催化氧化是该反应的控制步骤，反应符合L-H动力学规律．研究还发现，反应气氛对该光催化反应有明显影响．在实验条件下未观测到产物对反应的影响．     

浅池型TiO2/ACF光催化降解水中苯酚的研究

为了提高光催化过程的降解速率，本文以涂覆法制得的二氧化钛/活性炭纤维（TiO2/ACF）为光催化剂，300 W(365 nm)高压汞灯为光源，研究了浅池型反应器中苯酚在TiO2/ACF上的光催化降解动力学；探讨了光强度、高压汞灯滤光以及光源种类对降解反应的影响，并对光氧化，光催化和吸附过程进行了比较。结果表明：光氧化对苯酚的降解无效果，光催化降解速率常数与吸附速率常数之比为3.35/1；光强越大，光催化降解速率越快；高压汞灯不滤光时光催化降解速率明显加快，但光催化反应仍遵循准一级反应动力学方程；波长为254 nm紫外杀菌灯的降解效果高于波长为365 nm高压汞灯滤光后的降解效果。     

超声-光催化降解水中有机污染物

超声-光催化是一项近年发展起来的废水处理的新型高级氧化技术。该技术利用超声的空化效应、自由基效应以及机械效应强化光催化的催化效能,实现超声和光催化对水中有机污染物的协同降解。本文从水中有机污染物的超声-光催化降解机理、降解动力学、影响因素（光催化剂类型和投加量、超声频率和强度、溶液pH值、温度、反应物初始浓度、溶解性气体和离子强度）和反应器类型（悬浮型、固定床型）4个方面介绍了相关研究进展,提出了目前存在的主要问题,并展望了超声-光催化降解水中有机污染物的发展方向。     

光催化-膜分离集成反应器及其应用

 设计了一种新型光催化-陶瓷膜分离集成反应器,在反冲条件下利用此集成反应器进行了甲基橙光催化氧化反应,分别考察了陶瓷膜对光催化剂TiO2微粉的截留率、膜的渗透通量、光催化氧化脱色率以及不同膜分离压力下的光催化反应速率常数. 结果表明,TiO2-甲基橙悬浆液体系中TiO2微粉的截留率可达到99.9%, 经集成反应器完成一个反应周期后甲基橙氧化脱色率达到10%, 光催化氧化脱色效果高于圆柱式反应器.     

TiO2固定床光催化氧化头孢拉啶

 研究了抗生素头孢拉啶在负载型TiO2连续循环流动反应器中的降\r\n解，用红外和紫外光谱跟踪头孢拉啶的光催化降解过程．结果显示，在\r\n反应液流速4．5L／min，氧气流速1．6L／min，光照强度30W，反应温\r\n度28±2℃和反应时间120min的光催化氧化条件下，头孢拉啶能完全降\r\n解．光降解过程中头孢拉啶羧基的氧化比胺基容易．添加H2O2可以提高\r\n光催化氧化反应速率．光催化降解动力学研究表明，头孢拉啶的光催化\r\n氧化符合Langmuir－Hinshelwood一级动力学模型．     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Summary of development of the theory of stability of colloids and thin films

In this review, the research of the author in the field of colloidal systems is summarized. The factors influencing colloidal stability are systematized and analyzed. Examples are presented to illustrate the practical utilization of the theory of stability of colloids and thin films.This review was prepared on the basis of the works of the author, which were awarded the State Premium for 1991 in the field of science and technology, chemistry section.Institute of Physical Chemistry, Russian Academy of Sciences, 117915 Moscow. Translated from Izvestiya Akademii Nauk, Seriya Khimicheskaya, No. 8, pp. 1708–1717, August, 1992.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Thermodynamics of the formation of oxosulfides of rare-earth elements

The enthalpies of solution of several oxosulfides of rare-earth elements and the high-temperature enthalpies of oxosulfides and oxosulfates of lanthanum and yttrium were measured using solution calorimetry and high-temperature microcalorimetry techniques. Standard enthalpies of formation and some thermodynamic properties of oxosulfides and oxosulfates were calculated. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 2 pp. 294–297, February, 1997.     

探究“铁的锈蚀条件”实验创新设计

设计了铁的锈蚀实验,说明了铁钉的处理方法,增加了温度、酸、碱的影响条件,实现了铁跟蒸馏水及空气中氧气快速反应而生锈,使实验在5 min左右就能够得到准确的结果。