Multilayered films fabricated from plasmid DNA and a side-chain functionalized poly(beta-amino ester): surface-type erosion and sequential release of multiple plasmid constructs from surfaces

Hydrolytically degradable polyamines can be used to fabricate multilayered polyelectrolyte films that erode and release DNA in aqueous environments. Past studies have investigated films fabricated from poly(beta-amino ester) 1 and the influence of polymer backbone structure on film erosion and the release of anionic polyelectrolytes. This investigation sought to characterize the influence of polymer side-chain structure on the stability of multilayered films in physiologically relevant media. Here, we report on the fabrication and characterization of multilayered films approximately 150 nm thick assembled from plasmid DNA and side-chain functionalized polymer 2. We observed large differences in the behavior of films fabricated from polymer 2 as compared to films fabricated from polymer 1. Whereas films fabricated from polymer 1 erode and release DNA over approximately 2 days when incubated in phosphate-buffered saline, films fabricated from polymer 2 erode and release DNA over approximately 2 weeks. In addition, whereas films fabricated from polymer 1 undergo complex nanometer-scale physical transformations in aqueous media, characterization of the surfaces of films fabricated from polymer 2 by atomic force microscopy (AFM) demonstrates that the surfaces of these materials remain smooth and uniform during erosion. The apparent surface-type erosion of these materials permits the fabrication of ultrathin films with architectures that provide control over the timing and the order in which two different DNA constructs are released from surfaces. For example, the order in which two different DNA constructs are released from films and expressed by cells can be controlled to measurable extents by the relative order in which they are deposited during fabrication. These results suggest approaches to the localized and sequential release of multiple different DNA constructs to cells or tissues from the surfaces of tissue engineering scaffolds or implantable devices coated with multilayered films.     

沉积电位对电沉积ZnS薄膜的影响

采用电沉积方法,在不同沉积电位条件下,在氧化锡铟(ITO)导电玻璃上沉积制备了ZnS薄膜,利用XRD、SEM和UV-VIS测试技术对在不同沉积电位所制备薄膜的晶相结构、表面微观形貌和光学性能进行了表征.研究结果表明:沉积电位在1.5 V—1.7 V范围内制备的ZnS薄膜呈非晶态,其可见光透过率从60 %降低到20 %,薄膜的光学带隙约为3.97 eV.在沉积电位为2.0 V条件下所沉积薄膜为ZnS结晶相和金属Zn混合相,薄膜透过率显著降低.     

Improved Hydrophobicity of Macroalgae Biopolymer Film Incorporated with Kenaf Derived CNF Using Silane Coupling Agent

Hydrophilic behaviour of carrageenan macroalgae biopolymer, due to hydroxyl groups, has limited its applications, especially for packaging. In this study, macroalgae were reinforced with cellulose nanofibrils (CNFs) isolated from kenaf bast fibres. The macroalgae CNF film was after that treated with silane for hydrophobicity enhancement. The wettability and functional properties of unmodified macroalgae CNF films were compared with silane-modified macroalgae CNF films. Characterisation of the unmodified and modified biopolymers films was investigated. The atomic force microscope (AFM), SEM morphology, tensile properties, water contact angle, and thermal behaviour of the biofilms showed that the incorporation of Kenaf bast CNF remarkably increased the strength, moisture resistance, and thermal stability of the macroalgae biopolymer films. Moreover, the films’ modification using a silane coupling agent further enhanced the strength and thermal stability of the films apart from improved water-resistance of the biopolymer films compared to unmodified films. The morphology and AFM showed good interfacial interaction of the components of the biopolymer films. The modified biopolymer films exhibited significantly improved hydrophobic properties compared to the unmodified films due to the enhanced dispersion resulting from the silane treatment. The improved biopolymer films can potentially be utilised as packaging materials.     

RF magnetron sputtering of ZnO and Al-doped ZnO films from ceramic and nanopowder targets: a comparative study

Undoped zinc oxide (ZnO) and aluminium-doped zinc oxide (ZAO) thin films have been prepared on glass substrates by RF magnetron sputtering from ceramic and nanopowder targets at room temperature (RT). The effects of target nature on the properties of the films have been studied. The X-ray diffraction (XRD) patterns show that ZnO and Al-doped ZnO thin films are highly textured along the c-axis perpendicular to the surface of the substrate from either nanopowder or ceramic targets. From the SEM images, it appears that the surface morphologies of ZAO films exhibit difference from that of undoped ZnO films. All films exhibit a transmittance higher than 80% in the visible region. The optical band gap (E_g) of ZnO and ZAO films obtained from nanopowder target is higher than those prepared using ceramic target. In two cases, Al-doping leads to a larger optical band gap (E_g) of the films.     

Changes in Porosity and Amounts of Adsorbed Water in Sol-Gel Derived Porous Silica Films with Heat Treatment

Porous silica films were obtained by a heat treatment of poly(ethyleneglycol)-containing gels for micro-patterning. Changes in porosity and the amount of adsorbed water with the heat treatment temperature in the silica films were evaluated from the refractive index of the films. The apparent refractive index of the silica films in an ambient atmosphere was much higher than the intrinsic refractive index of the film due to the large amount of adsorbed water in the films. The amount of adsorbed water in the films decreased with an increase in the heat treatment temperature and became almost zero after a heat treatment at 850°C. The decrease in the amount of adsorbed water in the films was caused by the decrease in silanol groups, which acted as the sites for water adsorption in the films. The drastic decreases in thickness and in porosity of the films at temperatures from 850 to 950°C occurred after the disappearance of silanol groups in the films. The densification of the films due to collapse of the pores at high temperatures should have resulted from the viscous flow of silica network.     

STRATIFICATION IN EMULSION FILMS

Formation of films possessing a layered or stratified structure has been observed with foam films from liquid crystals, from concentrated surfactant solutions and in liquid layers on the surface of water. The stratifying films have a structure similar to that of the smectic phase which soaps are known to form in the bulk solution at high concentrations. The repeating units of which such films are built are the so-called black films: each unit consists of two surfactant layers interleaved by a thin aqueous core. In the study presented here we have observed that stratification can also take place in emulsion films from concentrated aqueous surfactant solutions. We have compared these results with those obtained for foam films using the same surfactant, i.e. sodium dodecylsulfate.     

Electroformation of giant liposomes from spin-coated films of lipids

This paper describes spin-coating of solutions of lipids and using the resulting thin films for electroformation of giant liposomes. Spin-coating made it possible to generate uniform films of lipids with controllable thickness over large surfaces (>25 cm(2)) of indium tin oxide. Establishing a range of thicknesses optimal for electroformation (25-50 nm), we demonstrate formation of giant liposomes from lipids (such as asolectin, phosphatidylserine, and phosphatidylglycerol) that do not readily form giant liposomes from traditional, droplet-derived films. We compared liposomes from a spin-coated film of lipids to liposomes formed from traditional droplet-derived films and found that spin-coated films produced larger (by factor of 2-5) and more abundant liposomes than droplet-derived films of lipids. Electroformation from spin-coated, homogenous lipid films of optimal thickness provided a reproducible way to obtain liposomes with diameters that are predominantly larger than 30 microm over the entire surface of formation.     

Effects of the polarizability and packing density of transparent oxide films on water vapor permeation

The tin oxide and silicon oxide films have been deposited on polycarbonate substrates as gas barrier films, using a thermal evaporation and ion beam assisted deposition process. The oxide films deposited by ion beam assisted deposition show a much lower water vapor transmission rate than those by thermal evaporation. The tin oxide films show a similar water vapor transmission rate to the silicon oxide films in thermal evaporation but a lower water vapor transmission rate in IBAD. These results are related to the fact that the permeation of water vapor with a large dipole moment is affected by the chemistry of oxides and the packing density of the oxide films. The permeation mechanism of water vapor through the oxide films is discussed in terms of the chemical interaction with water vapor and the microstructure of the oxide films. The chemical interaction of water vapor with oxide films has been investigated by the refractive index from ellipsometry and the OH group peak from X-ray photoelectron spectroscopy, and the microstructure of the composite oxide films was characterized using atomic force microscopy and a transmission electron microscope. The activation energy for water vapor permeation through the oxide films has also been measured in relation to the permeation mechanism of water vapor. The diffusivity of water vapor for the tin oxide films has been calculated from the time lag plot, and its implications are discussed.     

Thickness-dependent structural transitions in fluorinated copper-phthalocyanine (F16CuPc) films

The detailed structure of F16CuPc films on SiO2 has been determined by means of in situ grazing incidence X-ray diffraction from the first monolayer to thicker films. In contrast to films of the homologous H16CuPc molecule, the F16CuPc films exhibit the same structure independently from the deposition temperature. The films show a thickness-dependent polymorphism manifested in the in-plane crystal structure, which implies large differences in the molecular tilt within the cofacial stacking of the molecules.     

Behavior of a Chitosan–Drug System during Diffusion Processes

The process of water vapor sorption by medical chitosan films and the release of nonelectrolyte drugs from these films are investigated. It is shown that the nonelectrolyte drugs are unable to modify the chitosan matrix and cannot provide a prolonged drug release. The modification of chitosan–drug films, for example, by isothermal annealing or transition from the salt form of chitosan to the base one, is required to decelerate the release of drugs from the films.     

Controlling the Structural and Electrical Properties of Diacid Oligo(Phenylene Ethynylene) Langmuir–Blodgett Films

The preparation, characterization and electrical properties of Langmuir–Blodgett (LB) films composed of a symmetrically substituted oligomeric phenylene ethynylene derivative, namely, 4,4′‐[1,4‐phenylenebis(ethyne‐2,1‐diyl)]dibenzoic acid (OPE2A), are described. Analysis of the surface pressure versus area per molecule isotherms and Brewster angle microscopy reveal that good‐quality Langmuir (L) films can be formed both on pure water and a basic subphase. Monolayer L films were transferred onto solid substrates with a transfer ratio of unity to obtain LB films. Both L and LB films prepared on or from a pure water subphase show a red shift in the UV/Vis spectrum of about 14 nm, in contrast to L and LB films prepared from a basic subphase, which show a hypsochromic shift of 15 nm. This result, together with X‐ray photoelectron spectroscopic and quartz crystal microbalance experiments, conclusively demonstrate formation of one‐layer LB films in which OPE2A molecules are chemisorbed onto gold substrates and consequently ? COO? Au junctions are formed. In LB films prepared on a basic subphase the other terminal acid group is also deprotonated and associates with an Na⁺ counterion. In contrast, LB films prepared from a pure water subphase preserve the protonated acid group, and lateral H‐bonds with neighbouring molecules give rise to a supramolecular structure. STM‐based conductance studies revealed that films prepared from a basic subphase are more conductive than the analogous films prepared from pure water, and the electrical conductance of the deprotonated films also coincides more closely with single‐molecule conductance measurements. This result was interpreted not only in terms of better electron transmission in ? COO? Au molecular junctions, but also in terms of the presence of lateral H‐bonds in the films formed from pure water, which lead to reduced conductance of the molecular junctions.     

Surface-enhanced Raman scattering from bilayers of polystyrene,diglycidyl ether of bisphenol-A,poly(4-vinyl pyridine), and poly(4-styrene sulfonate)

Surface-enhanced Raman scattering (SERS) has been observed from thin films of polystyrene (PS), diglycidyl ether of bisphenol-A (DGEBA), and poly(4-vinyl pyridine) (PVP) deposited on silver island films Degradation of the polymers occurred rapidly during laser irradiation and was accompanied by the appearance of strong bands near 1375 and 1575 cm-1. These bands were attributed to the formation of graphite-like species by the silver-catalyzed thermal oxidation of the polymers induced by localized laser heating of the substrate. When the thin films of PS, DGEBA, or PVP were overcoated with much thicker films of a second polymer such as polystyrene sulfonate (PSS), the degradation was greatly reduced, and excellent SERS spectra of the PS, DGEBA, and PVP films were obtained. Overlayers reduced degradation within the first films deposited on silver island films by restricting the availability of oxygen at the interface to its solubility in the overlayer polymer or by altering the adsorption of oxygen onto the substrate. SERS was observed for the PS, DGEBA, and PVP films and the PSS overlayers when the films were deposited from relatively dilute solutions. When the PS, DGEBA, and PVP films were deposited from more concentrated solutions, SERS was not observed from the PSS overlayers. It was suggested that most of the SERS was due to a short-range, charge-transfer mechanism associated with sites of atomic scale roughness and that SERS was observed from the overlayer when the first film failed to occupy all of the sites.     

Glucomannan composite films with cellulose nanowhiskers

Spruce galactoglucomannans (GGM) and konjac glucomannan (KGM) were mixed with cellulose nanowhiskers (CNW) to form composite films. Remarkable effects of CNW on the appearance of the films were detected when viewed with regular and polarizing optical microscopes and with a scanning electron microscope. Addition of CNW to KGM-based films induced the formation of fiberlike structures with lengths of several millimeters. In GGM-based films, rodlike structures with lengths of several tens of micrometers were formed. The degree of crystallinity of mannan in the plasticized KGM-based films increased slightly when CNW were added, from 25 to 30%. The tensile strength of the KGM-based films not containing glycerol increased with increasing CNW content from 57 to 74 MPa, but that of glycerol-plasticized KGM and GGM films was not affected. Interestingly, the notable differences in the film structure did not appear to be related to the thermal properties of the films.     

Film thickness studies for the chemically synthesized conducting polyaniline

The chemical oxidation of aniline with ammonium persulphate (APS) in aqueous acidic medium to form polyaniline (PANI) films has been studied using the quartz crystal microbalance (QCM) technique. PANI films can also grow onto glass supports immersed in the reaction mixture during the polymerization. The optical absorption for these films was measured. Multilayer deposition of polymer films onto the gold electrode of QCM and onto the glass supports from consecutive repetitive treatments by the reaction mixture containing aniline and APS, were studied. The induction period, the yield and the growth rate of the polymer films during the multilayer deposition were discussed. A relation between the thickness of the films determined, from QCM technique and the optical absorption of the films was established. The electrical conductivity of the PANI films was also measured.     

Rough silver films studied by surface enhanced raman spectroscopy and low temperature scanning tunnelling microscopy

The surface topography of Ag films and surface enhanced Raman scattering (SERS) from benzene on Ag films have been simultaneously recorded. The Ag films were formed by vacuum deposition at temperatures ranging from 100 K to 500 K. Analysis of scanning tunnelling microscopy (STM) images shows that films formed below 250 K are fractal structures with Hausdorff-Besicovitch dimension 2.55 < D < 2.72, while for those formed above 250 K, D≈2. The lower temperature, rough films exhibit strong surface enhanced Raman scattering but the higher temperature, smooth films do not. We consider the consequences of fractal character and the possible correlation between this and the SERS activity of these films.     

Variation of lattice dimensions in epitaxial SnS films on MgO(001)

Epitaxial and polycrystalline SnS films were prepared on MgO(001) and glass substrates using molecular beam epitaxy. The films were characterized by X-ray diffraction method. The orientations of epitaxial films were (010)[100]SnS||(001)[100]MgO or (010)[001]SnS||(001)[100]MgO. Lattice parameters of the polycrystalline film closely resembled those of bulk SnS at room temperature. However, the lattice parameters of epitaxial films varied widely and were very different from those of bulk SnS at room temperature. Considering the lattice dimensions and a/c ratio, the films roughly correspond to bulk SnS at elevated temperatures from 371 to 666 K. SEM images of the films showed needle- or circular-like SnS crystallites segregated from the epitaxial films. Respective energies of indirect band gaps of the films and refractive index of the polycrystalline film were estimated using results of optical transmission experiments.     

Tin oxide coating on polytetrafluoroethylene films in aqueous solutions

Polytetrafluoroethylene (PTFE) films were successfully coated with tin oxide in aqueous solutions. Tin oxide was crystallized in the solution and formed nanocrystal coatings on the polymer films. The coatings consisted of SnO₂ and SnO crystals. They were assemblies of tin oxide nanosheet of about 10 to 50 nm in size and about 5 nm in thickness. The nanocrystal films can be exfoliated from the PTFE substrates. Tin oxide nanocrystal films had a rough liquid surface and a dense substrate‐side surface. Transparency of PTFE films coated with tin oxide was same as that of bare PTFE films in the range from 400 to 800 nm. The PTFE films coated with tin oxide nanocrystals can be pasted on desired substrates. Copyright © 2009 John Wiley & Sons, Ltd.     

Spectroscopy and photophysics of self-organized zinc porphyrin nanolayers. 1. Optical spectroscopy of excitonic interactions involving the soret band

The photophysical properties of excited singlet states of zinc tetra-(p-octylphenyl)-porphyrin in 5-25-nm-thick films spin-coated onto quartz slides have been investigated by optical spectroscopy. Analysis of the polarized absorption spectra using a dipole-dipole exciton model with two mutually perpendicular transition dipole moments per molecule shows that the films are built from linear aggregates, i.e., stacks with a slipped-deck-of-cards configuration. The molecular planes of the porphyrins in the stacks are found to be perpendicularly oriented with respect to the substrate plane. Assuming a value of 2-3 for the dielectric constant of the film, from the excitonic shift, an angle of 44 degrees +/- 3 degrees and an interplanar distance of 0.35-0.36 nm between adjacent porphyrins are calculated, close to the ground-state geometry in solution. The ordering in these films was further investigated by the effects of various solvents and temperature annealing. Spin-coating from toluene as a solvent results in highly ordered films, and annealing of these films has little effect on their absorption spectra. However, spin-coating from chloroform or pyridine or exposure of the films to these solvents in their vapor phases changes their ordering presumably due to incorporation of residual solvent molecules. Annealing yields absorption spectra identical to those of films spin-coated from toluene. The absorption spectra are insensitive to atmospheric moisture, in contrast to those of zinc tetraphenylporphyrin films lacking octyl substituents.     

Study on aluminium-based single films

In the present paper the authors studied isolated metallic films made from the same material used for making metallic foams, and then characterised their properties. Metal films were made from a liquid aluminium alloy reinforced with ceramic particles of known concentration. Melts without such particles were also investigated. It is shown that stable films could not be made from Al-Si alloy having no particles, and just extremely thin and fragile films could be made from commercially-pure Al. In contrast, aluminium alloys containing particles such as SiC and TiB(2) allowed pulling thin, stable films, which did not rupture. Significant thinning of films was observed when the particle concentration in the melt decreased. By in situ X-ray monitoring of liquid films during pulling, film thickness and drainage effects within the liquid film could be studied. The morphology and microstructure of films was characterised after solidification. Our work shows that the question of how foams are stabilised can be studied using a simplified system such as a film, instead of having to deal with the multitude of different structural elements present in a foam.     

Stability and Morphology of Gold Nanoisland Arrays Generated from Layer-by-Layer Assembled Nanoparticle Multilayer Films: Effects of Heating Temperature and Particle Size

This article reports the effects of heating temperature and composition of nanoparticle multilayer films on the morphology, stability, and optical property of gold nanoisland films prepared by nanoparticle self-assembly/heating method. First, nanoparticle-polymer multilayer films are prepared by the layer-by-layer assembly. Nanoparticle multilayer films are then heated at temperature ranging from 500 °C to 625 °C in air to induce an evaporation of organic matters from the films. During the heating process, the nanoparticles on the solid surface undergo coalescence, resulting in the formation of nanostructured gold island arrays. Characterization of nanoisland films using atomic force microscopy and UV-vis spectroscopy suggests that the morphology and stability of gold island films change when different heating temperatures are applied. Stable gold nanoisland thin film arrays can only be obtained after heat treatments at or above 575 °C. In addition, the results show that the use of nanoparticles with different sizes produces nanoisland films with different morphologies. Multilayer films containing smaller gold nanoparticles tend to produce more monodisperse and smaller island nanostructures. Other variables such as capping ligands around nanoparticles and molecular weight of polymer linkers are found to have only minimal effects on the structure of island films. The adsorption of streptavidin on the biotin-functionalized nanoisland films is studied for examining the biosensing capability of nanoisland arrays.