Strong optical feedback in birefringent dual frequency laser

Strong optical feedback in a birefringent dual frequency He--Ne laser with a high reflectivity feedback mirror has been investigated for the first time. The output characteristics of two orthogonally polarized modes are demonstrated in two different optical feedback cases: one is for both modes being fed back and the other is for only one of the modes being fed back. Strong mode competition can be observed between the two modes with strong optical feedback. And when one mode's intensity is near its maximum, the other mode is nearly extinguished. When both modes are fed back into the laser cavity, the mode competition is stronger than when only one mode is fed back. The difference in initial intensity between the two orthogonally polarized modes plays an important role in the mode competition, which has been experimentally and theoretically demonstrated.     

基于双折射双频激光器中的调频回馈位移测量研究

提出了一种基于双折射双频激光器中的调频回馈效应的位移测量系统，并在实验和理论两方面进行了研究.实验中保持回馈外腔长度不变，将一四分之一波片置于激光器内腔中，调制内腔长度，激光器的中心频率发生改变，激光器输出强度将发生周期性的变化.研究发现激光强度曲线的波动频率正比于回馈外腔长度与内腔长度之比.当该位移测量系统的外腔长度是内腔长度的6倍时，被测物体每移动半个光波长，激光强度波动12次，系统分辨率可以达到二十四分之一光波长.理论分析与实验结果相符合.研究表明该位移测量系统具有高分辨率、大测量范围、可工作于任意回馈水平等特点. 关键词： 调频回馈 位移测量 双折射双频激光器 强度波动频率     

Intensity tuning characteristics of double-mode He--Ne laser with optical feedback

This paper investigates the intensity tuning characteristics of a double longitudinal modes He--Ne laser subjected to optical feedback. The intensity undulations of the total light and the two modes are observed for different external cavity length. Two modulations of the internal cavity length are performed. One is only for the internal cavity length being modulated and the other is for both the internal and the external cavity length being modulated. The undulation frequency of the total light is found to be determined by the ratio of external cavity length to internal cavity length in both modulations. When the external cavity length is integral times of the internal cavity length, the fringe frequency of the total light could be seven or even more times of that in conventional optical feedback. A simple theoretical analysis is presented, which is in good agreement with the experimental results. The potential use of the experimental results is also discussed.     

双频激光回馈位移测量研究

提出了一种基于双频激光回馈效应的位移测量系统，并在理论和实验两方面进行了研究.实验中对激光器输出功率变化进行了探测，同时对两正交偏振光的光强变化进行了探测.研究发现当被测物体移动时，激光器输出功率受到调制，物体每移动半个光波长时，回馈信号为调制深度相等的两峰，系统分辨率提高了一倍，达到四分之一光波长.当物体运动方向改变时，两正交偏振光的光强变化顺序也随之改变，可以实现物体位移方向的判断.理论分析及模拟结果与实验结果相符合.研究表明该位移传感系统具有结构简单、分辨率高、可判向、测量范围大、可工作于强回馈区等优点. 关键词： 激光回馈 位移传感 自混合干涉 双频激光器     

基于非准直外腔的单频激光高阶回馈效应研究

对基于非准直外腔的单频激光高阶回馈现象及产生机理进行了研究,获得了调制幅度不均匀的高分辨率多重高阶回馈条纹,分析了多重高阶回馈条纹的特点及产生机制。提出采用基于光路阻挡的实验方法,在回馈镜反射率大于90%的强回馈中,发现了单重高阶回馈效应,获得了调制幅度均匀、无大包络的高分辨率单重高阶回馈条纹,其分辨率达到/10,而且还有进一步提高的潜力。单重高阶回馈条纹不但具有多重高阶回馈时高分辨率的优点,还具有传统弱回馈时调制幅度均匀、类正弦等特性,对进一步研制高精度回馈测量系统具有重要意义。     

腔调谐过程中激光器中两垂直偏振光的回馈特性

腔调谐过程中同时对HeNe激光器进行光回馈，设定回馈镜驱动信号的周期远小于腔调谐信号的周期，此时便获得腔调谐过程中谐振腔中两垂直偏振光的回馈信号. 回馈的形式分为仅垂直光回馈、仅平行光回馈以及两光同时回馈三种情况. 当两光同时回馈时，两模式间的模竞争较弱，两光回馈曲线有一定的相位差，该相位差小于180°，两光总体波动幅度变化趋势相反. 当仅单偏振光回馈时，两模式间的模竞争较强，两光回馈曲线始终反相，而且两光波动幅度变化趋势相同，此时可以将两光强度信号相减以实现成倍提高回馈信号幅度，从而提高系统灵敏度. 尤其仅垂直光回馈时，两光各自光强波动幅值都较大，并且在较大的增益曲线范围内保持光强波动幅值无明显变化，该特性可用于提高回馈系统的抗干扰能力，减少因激光功率漂移而引起的错误计数. 关键词： 自混合干涉 光回馈 模竞争 位移测量     

The optimal design for weak optical feedback semiconductor laser with frequency modulation

In this paper the frequency modulation characteristics the semiconductor laserwith weak optical feedback are presented,considering both the frequency deviation and thespurious intensity modulation.The frequency modulation can be realized without spurious in-tensity modulation under proper feedback conditions.There is an optimal feedback intensity tomaximize the frequency deviation.     

External optical feedback effects in a frequency locking dual frequency laser

We present a systematic study of external optical feedback effects on the output characteristics of the two orthogonally polarized modes in a frequency locking dual frequency laser. Accompanied by the change of the external cavity length, the length of the resonance cavity is changed very slowly to set the oscillating modes sweeping across the laser gain curve. Comprehensive results are obtained and a strong mode competition is observed. Particularly, when the laser runs in the middle region of the gain curve, which mode can oscillate is determined by the movement direction of the external feedback mirror. Based on the phenomenon, a displacement sensor with directional discrimination is proposed and its capability is also discussed.     

基于光线追迹的单频激光多重回馈效应研究

提出一种基于非准直平凹回馈腔的单频激光多重回馈光线追迹模型,采用该模型阐明了单频激光多重回馈效应的产生机理,分析了多重回馈高分辨率条纹的特性,明确了影响多重回馈条纹形状的主要因素,包括回馈镜的倾角、曲率半径、反射率以及回馈外腔长等,获得了回馈镜在不同倾角时的有效回馈阶次及其耦合系数。光线追迹分析与实验结果表明:当回馈镜倾斜角为1.7时,多重回馈效应会产生调制幅度均匀、没有大包络的高分辨率回馈条纹,每个条纹的分辨率可达/50。     

基于飞秒光频梳的双频He-Ne激光器频率测量

利用光纤飞秒光频梳和外腔可调谐半导体激光器, 建立了一套双频He-Ne激光器频率测量系统. 选用铷钟作为系统的频率基准, 通过将外腔半导体激光锁定至光频梳使得其频率溯源至铷钟, 再利用外腔可调谐半导体激光与双频He-Ne激光器输出的正交偏振激光拍频, 同时测量两路正交偏振激光频率. 将可调谐半导体激光器锁定至光频梳第1894449个梳齿, 其绝对频率为473612190000.0±2.7 kHz, 相对不确定度为5.7×10^-12. 对商品双频He-Ne激光器进行频率测量实验, 双频He-Ne激光器水平方向偏振激光频率均值为473612229934 kHz, 竖直方向偏振激光频率均值为473612232111 kHz, 平均时间为1024 s的相对Allan标准差为5.2×10^-11, 频差均值为2.177 MHz, 标准偏差为2 kHz.     

激光回馈效应及其传感应用研究的进展

对基于激光回馈效应的传感应用研究进展进行了综述。由于激光回馈引起激光器功率波动一个条纹对应外部反射镜移动半个光波波长,功率波动深度与传统双光束干涉系统相当,基于该现象的激光回馈干涉仪与传统的干涉仪相比具有相同的相位灵敏度。但其结构简单、紧凑、易准直的特点,引起了国内外科研者浓厚的兴趣,开发了很多全新概念、经济实用的精密测量仪器。对激光回馈效应在位移测量、速度测量、振动测量、距离测量、角度测量和形貌测量中的原理进行了介绍,同时对各传感应用系统进行了评述。     

Mode hopping in single-mode microchip Nd：YAG lasers induced by optical feedback

The mode hopping phenomenon induced by optical feedback in single-mode microchip Nd：YAG lasers is presented. With optical feedback, mode hopping strongly depends on two factors： the ratio of external cavity length to intra-cavity length, and initial gains of the two hopping modes, When external cavity length equals an integral multiple of intracavity length, there is almost no mode hopping. However, if the external cavity length does not equal an integral multiple of intra-cavity length, mode hopping occurs. The ratio of external cavity length to intra-cavity length determines the position of two-mode hopping, The initial gains of the two hopping modes determine the corresponding peak values and oscillating periods of them in the intensity modulation curves.     

A diode laser spectrometer at 634nm and absolute frequency measurements using optical frequency comb

This paper reports that two identical external-cavity-diode-laser (ECDL) based spectrometers are constructed at 634 nm referencing on the hyperfine B-X transition R(80)8-4 of ¹²⁷I₂. The lasers are stabilized on the Doppler-free absorption signals using the third-harmonic detection technique. The instability of the stabilized laser is measured to be 2.8×10^-12 (after 1000 s) by counting the beat note between the two lasers. The absolute optical frequency of the transition is, for the first time, determined to be 472851936189.5 kHz by using an optical frequency comb referenced on the microwave caesium atomic clock. The uncertainty of the measurement is less than 4.9 kHz.     

调频微片Nd:YAG激光器光回馈特性的研究

研究了调频微片Nd：YAG激光器的光回馈特性.在没有光回馈的情况下，激光频率每改变一个纵模间隔，激光器输出功率变化一个条纹.有光回馈时，同时改变激光频率和外腔相位，激光器输出功率波动频率正比于内、外腔长度之比.基于三镜腔等效模型的理论分析和实验结果相符合.并且讨论了这一现象在精密测量领域的潜在应用.     

High-frequency optical signal generation in a semiconductor laser by incoherent optical feedback

This work examines the feasibility of using incoherent optical feedback to generate high-frequency optical signals in a semiconductor laser. At a roundtrip feedback distance of 30 cm, a signal appears at around 1 GHz while the laser output is kept in single longitudinal mode and single polarization. The proposed method does not use any external modulation or saturable absorber. Some of the signal's properties are discussed as well.     

Optical feedback characteristics in a helium neon laser with a birefringent internal cavity

The output characteristics of optical feedback in a helium neon laser with a birefringent internal cavity are studied systematically in five different regions of the gain curve for the two orthogonally polarized modes. When the laser operates in the two end regions of the laser gain curve, one of the two orthogonally polarized modes will be a leading one in optical feedback. Strong mode competition can be observed. However, when the laser operates in the middle region of the laser gain curve, the two modes can oscillate equally with optical feedback. Besides the intensity of the two polarized lights, the total light intensity is also studied at the same time. M-shaped optical feedback curves are found. Particularly, when the average intensities of the two lights are comparable, the intensity modulation curve of the total light is doubled, which can be used to improve the resolution of an optical feedback system.[第一段]     

非相干光反馈表面轮廓测量实验研究

数值研究了非相干光反馈时半导体激光器输出功率随反馈系数的变化关系以及待侧物体离焦量与反馈系数的关系.提出了基于非相干光反馈的表面轮廓测量系统,并实验验证了系统的可行性,完成了对一元硬币的二维平面扫描成像,并分析了实验结果中的误差以及可能影响测量结果的主要因素.     

Precise determination of characteristic laser frequencies by an Er-doped fiber optical frequency comb

Femtosecond optical frequency combs correlate the microwave and optical frequencies accurately and coherently. Therefore, any optical frequency in visible to near-infrared region can be directly traced to a microwave frequency. As a result, the length unit "meter" is directly related to the time unit "second". This paper validates the capability of the national wavelength standards based on a home-made Er-doped fiber femtosecond optical frequency comb to measure the laser frequencies ranging from visible to near-infrared region. Optical frequency conversion in the femtosecond optical frequency comb is achieved by combining spectral broadening in a highly nonlinear fiber with a single-point frequency-doubling scheme. The signal-to-noise ratio of the beat notes between the femtosecond optical frequency comb and the lasers at 633, 698, 729, 780, 1064, and 1542 nm is better than 30 dB. The frequency instability of the above lasers is evaluated by using a hydrogen clock signal with a instability of better than 1×10^-13 at 1-s averaging time. The measurement is further validated by measuring the absolute optical frequency of an iodine-stabilized 532-nm laser and an acetylene-stabilized 1542-nm laser. The results are within the uncertainty range of the international recommended values. Our results demonstrate the accurate optical frequency measurement of lasers at different frequencies using the femtosecond optical frequency comb, which is not only important for the precise and accurate traceability and calibration of the laser frequencies, but also provides technical support for establishing the national wavelength standards based on the femtosecond optical frequency comb.     

强光注入提高光反馈VCSELs混沌载波基频

研究了外部光注入对光反馈垂直腔表面发射半导体激光器(VCSEL)混沌载波基频的影响.研究结果表明：当外部注入光频率与VCSEL自由运行的振荡频率失谐一定时,随着外部光注入强度的增加,混沌载波基频总体呈现上升的趋势;通过调整失谐频率和注入强度大小,外部光注入可以使混沌载波基频得到大幅度的提高;当归一化的注入系数K=330, 失谐频率为42 GHz,可得到基频位于47.3 GHz的混沌信号输出. 关键词： VCSEL 光注入 光反馈 混沌载波基频     

外腔镜非线性运动对激光回馈应力测量系统精度的影响及修正

基于激光的回馈效应可实现光学材料应力分布的测量, 而系统外腔镜的非线性运动会引起测量结果的误差, 影响系统的精度. 利用高精度Nd:YAG激光回馈干涉仪对外腔镜的位移随时间的变化进行测量, 采用高次拟合的方式得到位移与时间函数关系, 并利用三镜腔等效模型的调谐曲线方程, 对非线性运动引入的应力测量误差进行计算, 实现对系统精度的修正. 结果表明: 外腔镜运动方向不同, 引起的误差呈现相反的变化趋势; 将不同方向的测量结果进行平均, 可减小系统的测量误差. 分析了外腔镜非线性运动带来的误差对系统测量精度的影响, 提出了测量误差修正方法, 对提高系统的测量精度具有重要意义.