Decolorization of C.I. Reactive Red 2 by ozonation catalyzed by Fe(II) and UV

This work evaluated the effects of pH on decolorization of C.I. Reactive Red 2 by O₃, O₃/Fe(II), UV/O₃ and UV/O₃/Fe(II) systems. At pH 4, the decolorization rate constants of O₃, O₃/Fe(II), UV/O₃ and UV/O₃/Fe(II) systems were 1.78, 3.11, 2.04 and 3.18 hr⁻¹, respectively. The decolorization rates and effective energy consumption constants of all systems were higher under basic conditions than under acidic conditions.     

Conversion of NO in NO/N2, NO/O2/N2, NO/C2H4/N2 and NO/C2H4/O2/N2 Systems by Dielectric Barrier Discharge Plasmas

An experimental study on the conversion of NO in the NO/N₂, NO/O₂/N₂, NO/C₂H₄/N₂ and NO/C₂H₄/O₂/N₂ systems has been carried out using dielectric barrier discharge (DBD) plasmas at atmospheric pressure. In the NO/N₂ system, NO decomposition to N₂ and O₂ is the dominating reaction; NO conversion to NO₂ is less significant. O₂ produced from NO decomposition was detected by an on-line mass spectrometer. With the increase of NO initial concentration, the concentration of O₂ produced decreases at 298 K, but slightly increases at 523 K. In the NO/O₂/N₂ system, NO is mainly oxidized to NO₂, but NO conversion becomes very low at 523 K and over 1.6% of O₂. In the NO/C₂H₄/N₂ system, NO is reduced to N₂ with about the same NO conversion as that in the NO/N₂ system but without NO₂ formation. In the NO/C₂H₄/O₂/N₂ system, the oxidation of NO to NO₂ is dramatically promoted. At 523 K, with the increase of the energy density, NO conversion increases rapidly first, and then almost stabilizes at 93–91% of NO conversion with 61–55% of NO₂ selectivity in the energy density range of 317–550 J L⁻¹. It finally decreases gradually at high energy density. A negligible amount of N₂O is formed in the above four systems. Of the four systems studied, NO conversion and NO₂ selectivity of the NO/C₂H₄/O₂/N₂ system are the highest, and NO/O₂/C₂H₄/N₂ system has the lowest electrical energy consumption per NO molecule converted.     

Hydrothermal synthesis, characterization and thermochemistry of Ca2[B2O4(OH)2]·0.5H2O

A pure calcium borate Ca₂[B₂O₄(OH)₂]·0.5H₂O has been synthesized under hydrothermal condition and characterized by XRD, FT-IR and TG as well as by chemical analysis. The molar enthalpy of solution of Ca₂[B₂O₄(OH)₂]·0.5H₂O in HC1·54.582H₂O was determined. From a combination of this result with measured enthalpies of solution of H₃BO₃ in HC1·54.561H₂O and of CaO in (HCl + H₃BO₃) solution, together with the standard molar enthalpies of formation of CaO(s), H₃BO₃(s) and H₂O(l), the standard molar enthalpy of formation of −(3172.5 ± 2.5) kJ mol⁻¹ of Ca₂[B₂O₄(OH)₂]·0.5H₂O was obtained.     

Photodegradation of toluic acid isomers by UV/TiO2

This work elucidates the photodegradation of toluic acid isomers by UV/TiO₂. Effects of the toluic acid isomers, pH and form of TiO₂ on photodegradation are identified. The rate of photodegradation of toluic acid isomers in UV/TiO₂ obey the sequence p > o > m. Additionally, the reaction rates under acidic conditions exceed those under neutral and alkaline conditions.     

Ion-beam irradiation of lanthanum compounds in the systems La2O3-Al2O3 and La2O3-TiO2

Thin crystals of La₂O₃, LaAlO₃, La_2/3TiO₃, La₂TiO₅, and La₂Ti₂O₇ have been irradiated in situ using 1 MeV Kr²⁺ ions at the Intermediate Voltage Electron Microscope-Tandem User Facility (IVEM-Tandem), Argonne National Laboratory (ANL). We observed that La₂O₃ remained crystalline to a fluence greater than 3.1×10¹⁶ ions cm⁻² at a temperature of 50 K. The four binary oxide compounds in the two systems were observed through the crystalline-amorphous transition as a function of ion fluence and temperature. Results from the ion irradiations give critical temperatures for amorphisation (T_c) of 647 K for LaAlO₃, 840 K for La₂Ti₂O₇, 865 K for La_2/3TiO₃, and 1027 K for La₂TiO₅. The T_c values observed in this study, together with previous data for Al₂O₃ and TiO₂, are discussed with reference to the melting points for the La₂O₃-Al₂O₃ and La₂O₃-TiO₂ systems and the different local environments within the four crystal structures. Results suggest that there is an observable inverse correlation between T_c and melting temperature (T_m) in the two systems. More complex relationships exist between T_c and crystal structure, with the stoichiometric perovskite LaAlO₃ being the most resistant to amorphisation.     

Prussian Blue electrodeposited on MWNTs-PANI hybrid composites for H2O2 detection

A Prussian Blue (PB)/polyaniline (PANI)/multi-walled carbon nanotubes (MWNTs) composite film was fabricated by step-by-step electrodeposition on glassy carbon electrode (GCE). The electrode prepared exhibits enhanced electrocatalytic behavior and good stability for detection of H₂O₂ at an applied potential of 0.0 V. The effects of MWNTs thickness, electrodeposition time of PANI and rotating rate on the current response of the composite modified electrode toward H₂O₂ were optimized to obtain the maximal sensitivity. A linear range from 8 × 10⁻⁹ to 5 × 10⁻⁶ M for H₂O₂ detection has been observed at the PB/PANI/MWNTs modified GCE with a correlation coefficient of 0.997. The detection limit is 5 × 10⁻⁹ M on signal-to-noise ratio of 3. To the best of our knowledge, this is the lowest detection limit for H₂O₂ detection. The electrode also shows high sensitivity (526.43 μA μM⁻¹ cm⁻²) for H₂O₂ detection which is more than three orders of magnitude higher than the reported.     

Photocatalytic activity of TiO2/SnO2/Pt prepared by the sol-gel method

This investigation compares the photodegradation performance of C.I. Reactive Red 2 (RR2) in single- and coupled-photocatalyst systems. The photocatalysts were produced via the sol-gel method. PEG and Pt addition increases the decolorization rate (1.6–2.12 h⁻¹), the amount of sulfate released and the DOC reduction percentage in coupled photocatalyst systems the cause of PEG improving the homogeneity of the final product and incorporating Pt into the lattice reduced the band gap of photocatalysts.     

Intrinsic peroxidase-like catalytic activity of nitrogen-doped graphene quantum dots and their application in the colorimetric detection of H2O2 and glucose

In this paper, the highly intrinsic peroxidase-like catalytic activity of nitrogen-doped graphene quantum dots (N-GQDs) is revealed. This activity was greatly dependent on pH, temperature and H₂O₂ concentration. The experimental results showed that the stable N-GQDs could be used for the detection of H₂O₂ and glucose over a wide range of pH and temperature, offering a simple, highly selective and sensitive approach for their colorimetric sensing. The linearity between the analyte concentration and absorption ranged from 20 to 1170 μM for H₂O₂ and 25 to 375 μM for glucose with a detection limit of 5.3 μM for H₂O₂ and 16 μM for glucose. This assay was also successfully applied to the detection of glucose concentrations in diluted serum and fruit juice samples.     

Enzyme mimics of spinel-type CoxNi1−xFe2O4 magnetic nanomaterial for eletroctrocatalytic oxidation of hydrogen peroxide

A series of spinel-type Co_xNi_1−xFe₂O₄ (x = 0, 0.2, 0.4, 0.5, 0.6, 0.8, 1.0) magnetic nanomaterials were solvothermally synthesized as enzyme mimics for the eletroctrocatalytic oxidation of H₂O₂. X-ray diffraction and scanning electron microscope were employed to characterize the composition, structure and morphology of the material. The electrochemical properties of spinel-type Co_xNi_1−xFe₂O₄ with different (Co/Ni) molar ratio toward H₂O₂ oxidation were investigated, and the results demonstrated that Co_0.5Ni_0.5Fe₂O₄ modified carbon paste electrode (Co_0.5Ni_0.5Fe₂O₄/CPE) possessed the best electrocatalytic activity for H₂O₂ oxidation. Under optimum conditions, the calibration curve for H₂O₂ determination on Co_0.5Ni_0.5Fe₂O₄/CPE was linear in a wide range of 1.0 × 10⁻⁸–1.0 × 10⁻³ M with low detection limit of 3.0 × 10⁻⁹ M (S/N = 3). The proposed Co_0.5Ni_0.5Fe₂O₄/CPE was also applied to the determination of H₂O₂ in commercial toothpastes with satisfactory results, indicating that Co_xNi_1−xFe₂O₄ is a promising hydrogen peroxidase mimics for the detection of H₂O₂.     

Synthesis and thermochemistry of MgO·3B2O3·3.5H2O

A new magnesium borate MgO·3B₂O₃·3.5H₂O has been synthesized by the method of phase transformation of double salt and characterized by XRD, IR and Raman spectroscopy as well as by TG. The structural formula of this compound was Mg[B₆O₉(OH)₂]·2.5H₂O. The enthalpy of solution of MgO·3B₂O₃·3.5H₂O in approximately 1 mol dm⁻³ HCl was determined. With the incorporation of the standard molar enthalpies of formation of MgO(s), H₃BO₃(s), and H₂O(l), the standard molar enthalpy of formation of −(5595.02±4.85) kJ mol⁻¹ of MgO·3B₂O₃3.5H₂O was obtained. Thermodynamic properties of this compound was also calculated by group contribution method.     

α-Fe2O3/SiO2纳米颗粒混合体系表面的酸碱性质及其对重金属离子的吸附行为

以Fe(NO₃)₃·9H₂O和正硅酸乙酯(TEOS)为原料, 通过溶胶-凝胶法和辅助模板法分别制备了纳米α-Fe₂O₃和SiO₂, 并对所合成样品进行了粉末X射线衍射(XRD)和BET表征. 使用自动电位滴定仪测定了α-Fe₂O₃/SiO₂纳米颗粒混合体系的表面酸碱性质. 研究了在不同pH下α-Fe₂O₃/SiO₂混合体系对Cu²⁺、Pb²⁺、Zn²⁺离子的吸附行为. 基于上述实验数据, 用WinSGW软件计算了α-Fe₂O₃/SiO₂混合体系表面酸碱配位常数, 并得出结论: α-Fe₂O₃/SiO₂混合体系表面反应为单一脱质子反应≡XOH ⇔ ≡XO^-+ H⁺(lg K = -8.19±0.15), 明显区别于同时具有加质子和脱质子反应的α-Fe₂O₃/SiO₂/γ-Al₂O₃, α-Fe₂O₃/γ-Al₂O₃和SiO₂/γ-Al₂O₃等纳米颗粒混合体系. 在此基础上拟合得到α-Fe₂O₃/SiO₂混合体系吸附重金属离子Cu²⁺、Pb²⁺、Zn²⁺的表面络合反应平衡常数分别为:
≡XOH + M²⁺ ⇔ ≡XOM⁺+ H⁺ [lg K = -3.1, -3.6, -3.8 (M = Cu, Pb, Zn)].
≡XOH＋M²⁺＋H₂O ⇔≡XOMOH＋2H⁺[lg K = -8.8, -8.0, -10.5 (M = Cu, Pb, Zn)]     

Bulk and surface structures of V2O5/ZrO2 catalysts for n-butane oxidative dehydrogenation

The present investigation focuses on the structural properties and reactivity of zirconia-supported vanadium oxide catalysts, prepared by equilibrium adsorption in basic (pH 10) or in acid (pH 2.7) conditions with vanadium content up to 6 wt.% (pH 10) and up to 11.6 wt.% (pH 2.7). The samples, heated at 823 K for 5 h in air, were characterized by X-ray diffraction, Raman spectroscopy and TPR, both as prepared and after leaching with an ammonia solution to remove species not anchored to the zirconia surface. Some representative samples were also tested for the n-butane oxidative dehydrogenation (ODH) reaction. Depending on vanadium content, various vanadium species were identified by Raman spectroscopy that reacted differently on exposure to H₂. At similar loading, the fraction of vanadium in a dispersed state and thus interacting with the support was higher in samples prepared at pH 10 than in those at pH 2.7. Samples prepared at pH 2.7 contained a higher fraction of large polymeric structures in addition to ZrV₂O₇ and V₂O₅.In line with literature data for propane ODH on similar catalysts, our catalytic results suggested that the active sites for the ODH reaction are associated with the V–O–V bonds of the polymeric exposed structures, whereas the Zr–O–V sites favour alkane combustion.     

Solubility of (UO2)3(PO4)2?4H2O in H+-Na+-OH?-H2PO?4-HPO2?4-PO3?4-H2O and Its Comparison to the Analogous PuO2 +2 System

The objectives of this study were to address uncertainties in the solubility product of (UO₂)₃(PO₄)₂⋅4H₂O(c) and in the phosphate complexes of U(VI), and more importantly to develop needed thermodynamic data for the Pu(VI)-phosphate system in order to ascertain the extent to which U(VI) and Pu(VI) behave in an analogous fashion. Thus studies were conducted on (UO₂)₃(PO₄)₂⋅4H₂O(c) and (PuO₂)₃(PO₄)₂⋅4H₂O(am) solubilities for long-equilibration periods (up to 870 days) in a wide range of pH values (2.5 to 10.5) at fixed phosphate concentrations of 0.001 and 0.01 M, and in a range of phosphate concentrations (0.0001–1.0 M) at fixed pH values of about 3.5. A combination of techniques (XRD, DTA/TG, XAS, and thermodynamic analyses) was used to characterize the reaction products. The U(VI)-phosphate data for the most part agree closely with thermodynamic data presented in Guillaumont et al.,⁽¹⁾ although we cannot verify the existence of several U(VI) hydrolyses and phosphate species and we find the reported value for formation constant of UO₂PO⁻₄ is in error by more than two orders of magnitude. A comprehensive thermodynamic model for (PuO₂)₃(PO₄)₂⋅4H₂O(am) solubility in the H⁺-Na⁺-OH⁻-Cl⁻-H₂PO⁻₄-HPO²⁻₄-PO³⁻₄-H₂O system, previously unavailable, is presented and the data shows that the U(VI)-phosphate system is an excellent analog for the Pu(VI)-phosphate system.     

Synthesis, characterization, and thermochemistry of a new form of 2MgO·3B2O3·17H2O

A new magnesium borate, β-2MgO·3B₂O₃·17H₂O, has been synthesized by the method of phase transformation of double salt and characterized by XRD, IR, and Raman spectroscopy as well as by TG. The structural formula of this compound was Mg[B₃O₃(OH)₅]·6H₂O. The enthalpy of solution of β-2MgO·3B₂O₃·17H₂O in approximately 1 mol dm⁻³ HCl was determined. With the incorporation of the standard molar enthalpies of formation of MgO(s), H₃BO₃(s), and H₂O(l), the standard molar enthalpy of formation of −(10256.39±4.93) kJ mol⁻¹ of β-2MgO·3B₂O₃·17H₂O was obtained. Thermodynamic properties of this compound was also calculated by group contribution method.     

The mercury chromates Hg6Cr2O9 and Hg6Cr2O10—Preparation and crystal structures, and thermal behaviour of Hg6Cr2O9

The basic mercury(I) chromate(VI), Hg₆Cr₂O₉ (=2Hg₂CrO₄·Hg₂O), has been obtained under hydrothermal conditions (200 °C, 5 days) in the form of orange needles as a by-product from reacting elemental mercury and K₂Cr₂O₇. Hydrothermal treatment of microcrystalline Hg₆Cr₂O₉ in demineralised water at 200 °C for 3 days led to crystal growth of red crystals of the basic mercury(I, II) chromate(VI), Hg₆Cr₂O₁₀ (=2Hg₂CrO₄·2HgO). The crystal structures were solved and refined from single crystal X-ray data sets. Hg₆Cr₂O₉: space group P2₁2₁2₁, Z=4, a=7.3573(12), b=8.0336(13), , 3492 structure factors, 109 parameters, R[F²>2σ(F²)]=0.0371, wR(F² all)=0.0517; Hg₆Cr₂O₁₀: space group Pca2₁, Z=4, a=11.4745(15), b=9.4359(12), , 3249 structure factors, 114 parameters, R[F²>2σ(F²)]=0.0398, wR(F² all)=0.0625. Both crystal structures are made up of an intricate mercury-oxygen network, subdivided into single building blocks [O-Hg-Hg-O] for the mercurous compound, and [O-Hg-Hg-O] and [O-Hg-O] for the mixed-valent compound. Hg₆Cr₂O₉ contains three different Hg₂²⁺ dumbbells, whereas Hg₆Cr₂O₁₀ contains two different Hg₂²⁺ dumbbells and two Hg²⁺ cations. The Hg^I-Hg^I distances are characteristic and range between 2.5031(15) and 2.5286(9) Å. All Hg₂²⁺ groups exhibit an unsymmetrical oxygen environment. The oxygen coordination of the Hg²⁺ cations is nearly linear with two tightly bonded O atoms at distances around 2.07 Å. For both structures, the chromate(VI) anions reside in the vacancies of the Hg-O network and deviate only slightly from the ideal tetrahedral geometry with average Cr-O distances of ca. 1.66 Å. Upon heating at temperatures above 385 °C, Hg₆Cr₂O₉ decomposes in a four-step mechanism with Cr₂O₃ as the end-product at temperatures above 620 °C.     

Graphene enhanced electrochemiluminescence of CdS nanocrystal for H2O2 sensing

Graphene-CdS (G-CdS) nanocomposites were successfully prepared by CdS nanocrystals (CdS NCs) formed in situ on the surface of graphene sheets, using graphene oxide (GO) sheets with rich negatively charged carboxylic acid groups as starting materials. Compared with pure CdS NCs, the presence of the graphene doped in G-CdS nanocomposites could facilitate the electrochemical redox process of CdS NCs; further, the as-prepared G-CdS nanocomposite can react with H₂O₂ to generate strong and stable electrochemiluminescent (ECL) emission, which not only enhances its ECL intensity by about 4.3-fold but also decreases its onset potential for about 320 mV. The as-prepared solid-state ECL H₂O₂ sensor shows acceptable linear response from 5 μM up to 1 mM with a detection limit of 1.7 μM (S/N = 3). The ECL H₂O₂ sensor exhibits excellent reproducibility and long-term stability. Such a property would promote the potential application of the graphene as enhanced materials in fabricating sensors for chemical and biochemical analysis.     

Investigation on double perovskite Ba4Ca2Ta2O11

The structure, conductivity and water uptake of the oxygen-deficient perovskite-type compound Ba₄Ca₂Ta₂O₁₁ have been investigated. Ba₄Ca₂Ta₂O₁₁ crystallizes in the cryolite structure (cubic, Fm3m SG) with a = 8.4508(2) Å, under dry air. The compound can be partially hydrated up to a maximum water content of approximately 0.52 mol H₂O per mol Ba₄Ca₂Ta₂O₁₁. In moist air, the structure symmetry becomes monoclinic (C2/m) and the temperature dependence of total conductivity shows a different behavior because of changes in transport mechanism. Three regions can be observed as a function of temperature. For the low temperature range 200–400 °C, the protonic conduction is prevailing with an activation energy E_A = 0.85 eV. In the intermediate temperature range (400–600 °C), O²⁻ anionic and protonic conductions are mixed with an activation energy E_A = 0.45 eV and in the third region, for temperatures above 600 °C, O²⁻conduction is prevailing with an activation energy E_A = 0.85 eV.     

The Al2O3-Fe2O3 Mixed Oxidic System, II. Catalytic Decomposition of N2O

N₂O decomposition was examined over a series of Al₂O₃-Fe₂O₃ mixed oxidic solids with composition ranging from 0 to 100% of Fe₂O₃. The catalytic activity of the solids runs parallel to the number of atoms of iron in the Al_2−x Fe_xO₃ solid solution phase. Two compensation effects are present. The first corresponds to catalysts rich in alumina, and the second one to catalysts rich in hematite. This revised version was published online in June 2006 with corrections to the Cover Date.     

Preparation of ZrO2-TiO2-CeO2 and Its Application in the Selective Catalytic Reduction of NO with NH3

TiO₂,ZrO₂-TiO₂,andZrO₂-TiO₂-CeO₂ were prepared by co-precipitation method and characterized by X-ray diffraction (XRD), specific surface area measurements (BET), temperature programmed desorption (NH₃-TPD), oxygen storage capacity (OSC), and temperature programmed reduction (H₂-TPR). The results showed that ZrO₂-TiO₂-CeO₂ exhibited large number of surface strong acid, possessed some oxygen storage capacity, and strong redox property. The three materials were used as supports and the monolith catalysts were prepared with 1% (w) V₂O₅ and 9% (w)WO₃ for selective catalytic reduction (SCR) of NO with ammonia in the presence of excessive O₂, and the results of catalytic activity showed that the catalyst used ZrO₂-TiO₂-CeO₂ as support yielded nearly 100% NO conversion at 275 °C at a gas hourly space velocity (GHSV) of 10000 h⁻¹, and it had the best catalytic activity and showed great potential for practical application.     

Transition metal tetramolybdate dihydrates MMo4O13·2H2O (M=Co,Ni) having a novel pillared layer structure

Hydrothermal synthesis in the M/Mo/O (M=Co,Ni) system was investigated. Novel transition metal tetramolybdate dihydrates MMo₄O₁₃·2H₂O (M=Co,Ni), having an interesting pillared layer structure, were found. The molybdates crystallize in the triclinic system with space group P−1, Z=1 with unit cell parameters of a=5.525(3) Å, b=7.058(4) Å, c=7.551(5) Å, α=90.019(10)°, β=105.230(10)°, γ=90.286(10)° for CoMo₄O₁₃·2H₂O, and a=5.508(2) Å, b=7.017(3) Å, c=7.533(3) Å, α=90.152(6)°, β=105.216(6)°, γ=90.161(6)° for NiMo₄O₁₃·2H₂O The structure is composed of two-dimensional molybdenum-oxide (2D Mo-O) sheets pillared with CoO₆ octahedra. The 2D Mo-O sheet is made up of infinite straight ribbons built up by corner-sharing of four molybdenum octahedra (two MoO₆ and two MoO₅OH₂) sharing edges. These infinite ribbons are similar to the straight ones in triclinic-K₂Mo₄O₁₃ having 1D chain structure, but are linked one after another by corner-sharing to form a 2D sheet structure, like the twisted ribbons in BaMo₄O₁₃·2H₂O (or in orthorhombic-K₂Mo₄O₁₃) are.