980nm脉冲激发下Er~(3+)掺杂材料中~4I_(13/2)→~4I_(15/2)跃迁的瞬态行为(英文)

在过去的几十年人们对Er3+掺杂的玻璃材料进行了广泛的研究,因为Er3+的 4I13 /2→ 4I15 /2跃迁能够给出适合红外光通讯窗口的 1. 5μm的发射。据我们所知,目前关于脉冲激光激发下Er3+掺杂材料 1. 5μm发射的动力学行为研究报道仍很少。我们引入了转移函数理论,研究了 980nm脉冲激发下Er3+的 4I13 /2能级荧光的动力学行为。发现在 980nm脉冲激发后,其荧光衰减遵循双指数规律,4I13 /2能级布居分为指数上升和指数下降两个过程。     

WO3对掺铒碲酸盐玻璃光谱性质的影响

制备了掺铒碲钨酸盐玻璃(80-x)TeO2-(10 x)WO3-8BaO-2Na2O-O.5Er2O3(x=0,5,10,15,20)玻璃,研究了WO3对掺铒碲钨酸盐玻璃的光谱性质.研究发现:随着WO3含量的增加,Ω4,Ω6先增加后减小,受激发射截面也是先增加后减小,而Ω2的变化则相反.由McCumber理论计算了掺铒碲钨酸盐玻璃在1.5μm的受激发射截面,其最大受激发射截面为0.96×10-21 cm2,Er3 的4I13/2→4I15/12的跃迁发射荧光光谱的最大荧光半高宽为82 nm.同时,实验发现,在976 nm抽运下,掺铒碲酸盐玻璃存在较强的荧光上转换现象,随WO3含量的增加,上转换荧光强度呈降低的趋势.     

Yb^3＋/Er^3＋掺杂氟氧化物微晶玻璃的制备与发光性能

采用高温熔融法制备了Yb3＋/Er3＋掺杂的氟氧化物发光微晶玻璃,确定了最佳熔化温度（1 100℃）和退火温度（440℃,480℃）。测定得到基质玻璃的透过率为85%,掺入稀土后,透过率有所下降,并出现了稀土离子的特征吸收峰。980 nm半导体激光器（LD）激发下样品的上转换发射光谱存在4个明显的发射峰,分别为410,532,546和656 nm,对应于2H9/2→4I15/2,2H11/2→4I15/2,4S3/2→4I15/2和4F9/2→4I15/2跃迁。研究了不同Yb3＋/Er3＋（摩尔分数）和Er3＋浓度对上转换发光强度的影响,当Yb3＋∶Er3＋=4∶1、Er3＋摩尔分数为1.5%时,上转换发光强度达到最高。根据发光强度与泵浦功率之间的关系,确定了上转换发射均为双光子过程。讨论了Yb3＋,Er3＋离子间的能量传递,建立了上转换发光机制。     

Yb~(3+)/Er~(3+)掺杂氟氧化物微晶玻璃的制备与发光性能

采用高温熔融法制备了Yb3+/Er3+掺杂的氟氧化物发光微晶玻璃,确定了最佳熔化温度(1 100℃)和退火温度(440℃,480℃)。测定得到基质玻璃的透过率为85%,掺入稀土后,透过率有所下降,并出现了稀土离子的特征吸收峰。980 nm半导体激光器(LD)激发下样品的上转换发射光谱存在4个明显的发射峰,分别为410,532,546和656 nm,对应于2H9/2→4I15/2,2H11/2→4I15/2,4S3/2→4I15/2和4F9/2→4I15/2跃迁。研究了不同Yb3+/Er3+(摩尔分数)和Er3+浓度对上转换发光强度的影响,当Yb3+∶Er3+=4∶1、Er3+摩尔分数为1.5%时,上转换发光强度达到最高。根据发光强度与泵浦功率之间的关系,确定了上转换发射均为双光子过程。讨论了Yb3+,Er3+离子间的能量传递,建立了上转换发光机制。     

Er3+离子掺杂钡镓锗玻璃上转换发光机理研究

研究了Er3+离子掺杂钡镓锗玻璃的吸收光谱、拉曼光谱和上转换光谱.分析了Er3+离子在钡镓锗玻璃中的上转换发光机理.结果表明:玻璃的最大声子能量为828cm-1,紫外截止波长为275nm.采用800nm和980nmLD激发玻璃样品,在室温下观察到强烈的上转换绿光和红光发射.随着Er3+离子浓度的增加,绿光发光强度先增加后减小,而红光发光强度呈单调递增趋势.能量分析表明:800nmLD激发产生的绿光主要源于Er3+离子4I13/2能级的激发态吸收过程;红光发射主要源于Er3+离子4I13/2能级与4I11/2能级之间的能量转移过程.980nmLD激发产生的绿光主要源于Er3+离子4I11/2能级之间的能量转移过程;而红光发射主要源于Er3+离子4I13/2能级与4I11/2能级之间的能量转移过程和4I13/2能级的激发态吸收过程.通过量子效率分析,发现采用800nmLD激发Er3+离子掺杂浓度为1mol% 的样品时,上转换绿光发光效率最高.     

氟化物对Er~(3+)/Yb~(3+)共掺的碲酸盐玻璃上转换和红外发光性能的影响

Er3+/Yb3+共掺的碲酸盐玻璃由于其良好的上转换发光性能而得到广泛的研究。本文将氟化物引入碲酸盐玻璃中,通过熔融法制备了量比为70TeO2-(30-x)ZnO-xZnF2-0.15Er2O3-1.5Yb2O3(x=0,5,10,15,20)的碲酸盐氧氟玻璃样品,并测试其热稳定性、拉曼光谱以及受激发射光谱。实验结果表明,随着氟化物含量的提高,Er3+离子的410,555,670 nm上转换发光和2~3μm波段中红外发光得到增强,并且红光提高强度比绿光和蓝光更明显。在分析了氟离子引入后对上转换与近中红外波段发光的内在影响机制发现:碲酸盐玻璃系统中的氟化物一方面促进能量传递过程中Er3+离子的双光子吸收,促进粒子跃迁至相应的高能级;另一方面,引入氟化物后的碲酸盐玻璃的最大能量声子态密度下降也是降低无辐射跃迁概率、提高上转换和中红外发射强度的重要原因。     

GeO2含量对掺铒锗碲酸盐玻璃物性和光谱特性的影响

本文研究了x GeO2-(70-x)TeO2-5K2O-5Na2O-10Nb2O5-10ZnO-0.2Er2O3(x=0,10,25,50,70(摩尔百分数))玻璃的物性和光谱特性,讨论GeO2含量对锗碲酸盐玻璃物性和光谱特性的影响.研究发现:GeO2的加入提高了碲酸盐玻璃热稳定性,并且使玻璃的最大声子能量略微增加;随GeO2的增加,掺Er3+锗碲酸盐玻璃的Judd-Ofelt强度参量Ω2和Ω6逐渐增大,但玻璃受激发射截面有减小的趋势;由McCumber理论,计算了掺铒锗碲酸盐玻璃在1.53μm处最大受激发射截面为9.92×10-21cm2,Er3+离子4I13//2→4I15/2发射谱的最大荧光半高宽为52nm,同时,实验发现,在977nm LD抽运下,掺铒锗碲酸盐玻璃存在较强的荧光上转换现象,随GeO2含量的增加,上转换荧光强度呈降低的趋势.     

980 nm脉冲激发下Er3+掺杂材料中4Ⅰ13/2→4Ⅰ15/2跃迁的瞬态行为

在过去的几十年人们对Er3+掺杂的玻璃材料进行了广泛的研究,因为Er3+的4Ⅰ13/2→4Ⅰ15/2跃迁能够给出适合红外光通讯窗口的1.5 μm的发射.据我们所知,目前关于脉冲激光激发下Er3+掺杂材料1.5 μm发射的动力学行为研究报道仍很少.我们引入了转移函数理论,研究了980nm脉冲激发下Er3+的4Ⅰ13/2能级荧光的动力学行为.发现在980nm脉冲激发后,其荧光衰减遵循双指数规律,4Ⅰ13/2能级布居分为指数上升和指数下降两个过程.     

硼碲酸盐玻璃材料中Er3+光谱性质对组分的依赖关系

采用熔融淬火技术制备了一组Er3+掺杂的变组分硼碲酸盐玻璃材料.测量了玻璃的折射率、吸收光谱及4I13/2→4I15/2跃迁的荧光寿命.利用标准的三参量Judd Ofelt理论对Er3+的光学跃迁性质进行了计算,并对Er3+离子的4I13/2能级的量子效率进行了研究.结果发现,随着样品中TeO2含量的增加样品的折射率变大,三个Judd Ofelt参量中Ω2随着样品组分的改变较明显,而另外两个参量Ω4和Ω6的变化较小.还发现随着TeO2含量的增加4I13/2→4I15/2辐射跃迁几率增大,并且该跃迁的量子效率增加.这一研究结果表明,在硼酸盐玻璃材料中引入TeO2可以有效地改善其中稀土离子的量子效率和辐射跃迁性能.     

球形BaZnF_4∶Yb,Er纳米颗粒的热分解法合成及其上转换发光性质

采用热分解法制备了Ba Zn F4∶Yb,Er纳米颗粒。通过荧光分光光度计、X射线粉末衍射仪(XRD)和透射电子显微镜(TEM)对样品进行了表征。合成样品的形貌为球形,晶相为四方相,平均粒径为8 nm。当敏化剂Yb3+和激活剂Er3+的掺杂摩尔分数分别为20%和4%时,样品的发光性能较好。绿光和红光发射对应的辐射跃迁分别为Er3+离子的2H11/2→4I15/2(绿光)和4S3/2→4I15/2(绿光),以及Er3+离子的4F9/2→4I15/2(红光)。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.