现场岩屑核磁共振分析技术的实验研究

提出了利用核磁共振技术进行现场岩屑油层物理参数定量分析的方法. 在室内实 验研究的基础上，对比分析了核磁共振岩屑分析与核磁共振岩心分析的异同，对现场核磁共振岩屑分析的可行性进行了研究，给出了利用核磁共振技术确定岩屑孔隙度、渗透率等重 要油层物理参数的方法.     

水驱油过程的核磁共振二维谱研究

岩心水驱油过程中油水分布状况是岩心多孔介质的重要性质. 水驱油过程的研究是进一步进行提高采收率研究的基础. 核磁共振扩散-弛豫二维谱提供了岩心中流体性质的多方面信息,与核磁共振一维弛豫谱相比极大地提高了区分油水的能力. 该文通过2组岩心水驱油实验,从不同含油饱和度的扩散-弛豫二维谱中提取出水的一维弛豫谱,在原油粘度比较高的情况下获得了驱替过程中油水在不同孔隙中的分布状况以及润湿性等信息, 解决了单独用一维弛豫谱方法难以区分油水的问题. 该文的研究方法对油田提高采收率的研究有比较大的参考价值.     

油水饱和球管孔隙模型弛豫的理论计算与计算机模拟

根据Brownstein-Tarr理论,采用特征函数展开法,通过求解基于扩散效应的Bloch控制方程,给出了油水饱和球管孔隙模型弛豫的理论计算公式.理论计算结果表明,在水润湿条件下,油的弛豫过程只与含油饱和度有关,而与岩石的孔隙结构无关.根据理论计算结果对球管模型中水的弛豫进行了数值模拟,模拟结果显示,球和管的主弛豫过程是一个单指数函数,其余部分与之相比可以忽略,即球管模型中水的弛豫可近似为一个双指数衰减过程. 关键词： 核磁共振 弛豫 球管孔隙模型 Bloch控制方程     

2D NMR技术在石油测井中的应用

近几年,2D NMR技术得到迅速发展,特别是在核磁共振测井领域. 该文将主要介绍2D NMR技术的脉冲序列、弛豫原理以及2D NMR技术在石油测井中应用. 2D NMR技术是在梯度场的作用下,利用一系列回波时间间隔不同的CPMG脉冲进行测量,利用二维的数学反演得到2D NMR. 2D NMR技术可以直接测量自扩散系数、弛豫时间、原油粘度、含油饱和度、可动水饱和度、孔隙度、渗透率等地层流体性质和岩石物性参数. 从2D NMR谱上,可以直观的区分油、气、水,判断储层润湿性,确定内部磁场梯度等. 2D NMR技术为识别流体类型提供了新方法.     

钻井液粉末状荧光添加剂的核磁共振特性

磺化沥青等粉末状钻井液荧光添加剂有助于保障钻井安全,却不利于油气显示的发现.为了解决油气勘探与钻井安全之间的这个矛盾,创新采用高分辨率低场核磁共振技术,对14种粉末状荧光添加剂进行了不同混入介质(水和钻井液)、不同混入比例(荧光级别)和不同温度(32℃,90℃和150℃)条件下的核磁共振实验研究.结果表明,这些荧光添加剂可分为两类:一类是没有核磁共振信号;另一类会产生一个水化峰,但加弛豫试剂后水化峰消失.因而,粉末状荧光添加剂对采用核磁共振技术发现钻井液中的含油显示没有影响,从而可彻底解放对该类添加剂的使用限制.     

含油岩屑固体粉末荧光的研究

通过对含油岩屑固体粉末荧光的研究,指出了在固体粉末中含油浓度在一定范围内时,其粉末荧光强度与含油的浓度成线性关系,对二者关系进行线性拟合,其相关系数R=0．9936。当样品中的含油的浓度达到一定程度时,其荧光强度保持一个恒定的值。同时,研究了固体粉末荧光猝灭现象以及猝灭机制。指出含油岩屑粉末的荧光猝灭,主要是生荧团分子之间形成络合物以及由于激发光谱和发射光谱重叠所引起的交叉弛豫所致。最后比较了固体粉末中荧光浓度猝灭与溶液中浓度猝灭。这些对于研究和开发对含油岩屑直接进行荧光检测的录井技术具有重要的指导意义。     

油水饱和球管孔隙模型弛豫的理论计算与计算机模拟

根据Brownstein-Tarr理论，采用特征函数展开法，通过求解基于扩散效应的Bloch控制方程，给出了油水饱和球管孔隙模型弛豫的理论计算公式.理论计算结果表明，在水润湿条件下，油的弛豫过程只与含油饱和度有关，而与岩石的孔隙结构无关.根据理论计算结果对球管模型中水的弛豫进行了数值模拟，模拟结果显示，球和管的主弛豫过程是一个单指数函数，其余部分与之相比可以忽略，即球管模型中水的弛豫可近似为一个双指数衰减过程.     

二维核磁共振观测岩石润湿性

润湿性是反映储层中油水分布状况的一个重要表征参数,因此研究储层岩石的润湿性对原油开采有着重要的意义. 扩散弛豫二维谱可展示扩散系数与弛豫时间的相关性,并可以对油水的弛豫时间、扩散系数分别进行研究,与核磁共振一维弛豫谱相比极大地提高了区分油水的能力. 该文首先通过多组实验验证扩散-弛豫二维谱可以很好地观测到油水共存状态下玻璃珠表面的润湿性,继而通过对3组人造岩心表面润湿性的测量,获得了人造岩心表面润湿性的信息,解决了此时单独用一维弛豫谱方法难以区分油水的问题. 利用二维谱观察岩石润湿性的研究对油田提高采收率的研究有较大的参考价值.     

油料种子含油含水率的CPMG序列核磁共振测量

油料种子含油含水率是衡量其品质的重要标准,核磁共振作为测量油料种子含油含水率的一种新方法,越来越受到重视.本文利用低场核磁共振教学实验仪,在没有已知含油含水率油料种子的情况下,提出了采用CPMG序列作为测量序列的新方法,并用该方法测量了油料种子的含油含水率,扩充并改良了脉冲核磁共振学生实验,可以让学生对于核磁共振的应用有更深刻的理解.     

一种基于组分补偿的二维核磁共振测井数据高精度处理方法

二维核磁共振技术能够对储层中各类含氢流体进行无损、快速、定量的测量和表征，但受限于采集方式和参数，核磁共振设备在对页岩油等致密储层中的有机质、沥青等超快弛豫组分进行检测时，经常出现由于信号采集不完整所导致的二维谱中流体组分缺失或不准的问题.本文提出了基于超快弛豫组分补偿技术的T₂-T₁二维谱高精度反演方法，该方法将一维核磁共振前端信号补偿技术进行推广，通过在二维核磁数据反演前对回波数据进行组分补偿，能够有效解决二维核磁共振测井前端信号漏失的问题.实验及测井数据的应用表明，该方法在页岩油等富含快弛豫组分信号的储层中，可以得到更加精准和完整的储层信息.     

陆相储层岩石核磁共振物理特征的实验研究

以中国大量存在的陆相沉积岩为对象,系统研究了岩石核磁共振特征与岩石物理性质的关系,详细阐述了将核磁共振测量参数正确地转化为石油工业可直接应用的油层物理参数的方法,对比阐明了核磁共振测量结果与常规岩心分析的异同.针对我国陆相沉积岩核磁共振的特有性质,与国外的一些研究结果进行了对比. 本文研究结果对在中国开展核磁共振石油工业应用具有重要意义.     

Investigation on Mechanisms of Polymer Enhanced Oil Recovery by Nuclear Magnetic Resonance and Microscopic Theoretical Analysis

Polymer flooding is an efficient technique to enhance oil recovery over water flooding. There are lots of discussions regarding the mechanisms for polymer flooding enhancing oil recovery. The main focus is whether polymer flooding can increase sweep efficiency alone, or can increase both of sweep efficiency and displacement efficiency. We present a study on this problem. Oil displacement experiments on 4 natural cores show that polymer flooding can increase oil recovery efficiency by more than 12% over water. Moreover, photos are taken by the nuclear magnetic resonance （NMR） method both after water flooding and after polymer flooding, which show remaining oil saturation distribution at the middle cross section and the central longitudinal section. Analyses of these photos demonstrate that polymer flooding can increase both sweep efficiency and displacement efficiency.     

Overhauser DNP and EPR in a Mobile Setup: Influence of Magnetic Field Inhomogeneity

Power-dependent Overhauser dynamic nuclear polarization (DNP) enhancements and continuous-wave electron paramagnetic resonance (EPR) spectra of nitroxide radicals were measured in the magnetic field of a mobile Halbach-array permanent magnet and compared with results from a commercially available electromagnet. DNP saturation factors for varying microwave power were obtained from both measurement series and used to investigate how the increased magnetic field inhomogeneity present in the Halbach magnet affects the saturation efficiency. An EPR detection system was designed to allow continuous-wave EPR measurements at microwave power up to 20?W. Our results show that despite the lower magnetic field homogeneity, a Halbach-array magnet can be used for EPR and DNP-enhanced nuclear magnetic resonance of high quality providing almost the same performance as a more homogeneous electromagnet.     

Imaging of multiphase fluid saturation within a porous material via sodium NMR

We present in this paper a method to monitor multiphase fluid core saturation through measurement of the sodium NMR signal. In a rock core saturated with water and oil, sodium will be present only in the water phase, and therefore can be used to separate the two fluids. Two dimensional sodium images were taken to monitor the movement of brine into oil saturated rock cores. The measured fluid exchange agrees well with expected behavior from traditional core analysis methods. Indications of damage to the rock structure can be seen from the patterns of fluid imbibition.     

油井样品NMR T2谱的影响因素及T2截止值的确定方法

T₂ 谱是核磁共振（NMR）测、录井技术应用与解释、评价的基础. 岩样T₂ 谱受仪器测量参数、样品性质（岩性、颗粒大小、样品粒度、样品干湿状态、孔隙流体含量及性质、磁化率、润湿性）及地层水矿化度等因素的影响. T₂ 截止值是T₂ 谱中最重要的参数之一,选取的科学性与准确性直接影响到核磁共振测量结果. 通过文献查询,对T2 谱的影响因素及T₂ 截止值的确定方法进行了分析.     

Correcting for incomplete saturation and off-resonance effects in multiple-site saturation-transfer kinetic measurements

The effects of incomplete saturation and off-resonance irradiation on nuclear magnetic resonance saturation-transfer measurements of three-site chemical-exchange rates are discussed. A new method that uses double-saturation measurements is compared with two published methods, one that uses single-saturation measurements and one that uses a single-saturation measurement and a double-saturation measurement. Several formulas are compared for measuring the exchange rate constant k(DE) for exchange from a detected spin D to an exchanging spin E in the presence of exchange from spin D to a competing spin C. For each method, formulas are derived with corrections for incomplete saturation or off-resonance effects, with both corrections, and with neither correction. Exact formulas are available for three exchanging sites with incomplete saturation if there are no off-resonance effects. Off-resonance corrections are imperfect even with complete saturation.     

High Precision Identification of Igneous Rock Lithology by Laser Induced Breakdown SpectroscopySCIEI北大核心CSCD

In the field of petroleum exploration, lithology identification of finely cuttings sample, especially high precision identification of igneous rock with similar property, has become one of the geological problems. In order to solve this problem, a new method is proposed based on element analysis of Laser-Induced Breakdown Spectroscopy (LIBS) and Total Alkali versus Silica (TAS) diagram. Using independent LIES system, factors influencing spectral signal, such as pulse energy, acquisition time delay, spectrum acquisition method and pre-ablation are researched through contrast experiments systematically. The best analysis conditions of igneous rock are determined: pulse energy is 50 mJ, acquisition time delay is 2 mu s, the analysis result is integral average of 20 different points of sample's surface, and pre-ablation has been proved not suitable for igneous rock sample by experiment. The repeatability of spectral data is improved effectively. Characteristic lines of 7 elements (Na, Mg, Al, Si, K, Ca, Fe) commonly used for lithology identification of igneous rock are determined, and igneous rock samples of different lithology are analyzed and compared. Calibration curves of Na, K, Si are generated by using national standard series of rock samples, and all the linearly dependent coefficients are greater than 0.9. The accuracy of quantitative analysis is investigated by national standard samples. Element content of igneous rock is analyzed quantitatively by calibration curve, and its lithology is identified accurately by the method of TAS diagram, whose accuracy rate is 90.7%. The study indicates that LIBS can effectively achieve the high precision identification of the lithology of igneous rock.     

激光诱导击穿光谱技术对火成岩岩性的高精度识别

在石油勘探领域,细碎岩屑样品的岩性识别,特别是物性接近的火成岩的高精度识别是地质学的难题之一。针对这一问题,提出了一种基于激光诱导击穿光谱技术(LIBS)元素分析和全碱-硅(TAS)图版的新方法。利用自主搭建的LIBS系统,首先通过对比实验,系统的研究了脉冲能量、采集延时、采集方式、预燃对光谱信号的影响,确定了对火成岩样品元素分析的最佳条件：脉冲能量50 mJ,采集延时2 μs,采集同一样品表面20个不同点的光谱积分平均,并通过实验证明了预燃的样品处理方式不适合火成岩样品,有效提高了样品检测光谱数据的重复性。随后确定了火成岩岩性识别常用7种元素(钠镁铝硅钾钙铁)的特征谱线,定性分析和比较了不同岩性的火成岩样品;利用已知元素含量的国标系列岩石样品信息,生成了钠、硅、钾的定标曲线,线性相关系数均大于0.9,并利用国标岩石样品考察了定量分析的准确性;利用定标曲线法定量分析了火成岩样品的元素含量,并采用TAS图版法识别火成岩的岩性,准确率达90.7%。研究表明,LIBS技术能够有效实现火成岩岩性的高精度识别。