含三苯胺结构癈聚酰亚胺的合成及光电转换性能研究

通过缩聚方法合成了主链含三苯胺结构的苝聚酰亚胺，将其负载在纳米二氧化钛膜上，光电转换性能测定结果表明，含三苯胺结构苝聚酰亚胺具有良好的光电转换特性，其光电流比不含三苯胺结构的苝聚酰亚胺大11倍。     

Improvement of dye-sensitized solar cells' performance through introducing suitable heterocyclic groups to triarylamine dyes

Dye-sensitized solar cells are currently under intense academic and industrial investigation, owing to their great potential to serve as a low-cost alternative to existing photovoltaic technologies. This paper puts forward a method, which adopts heterocyclic substituted triarylamine units as electronic donor moieties, to design triarylamine dyes for efficient dye-sensitized solar cells. Three novel triarylamine dyes named TTC101, TTC102 and TTC103, were synthesized economically through modification of the structure of a simple triarylamine dye (TC105) using three kinds of heterocyclic groups (4-pyridyl, 2-thienyl and 1-pyrazolyl). The crystal structure of TTC103 indicates that the heterocyclic groups would partly delocalize the positive charge after photooxidation. The overall solar-to-electrical energy conversion efficiencies (η) of TTC102 and TTC103 are 4.92% and 5.21% respectively under AM1.5G irradiation, reaching ～82.3% and ～77.7% of a N719-based reference cell under the same conditions. Besides, the energy conversion efficiencies (η) of TTC102 and TTC103 are 1.29 and 1.37 times the efficiency of TC105 respectively. All of the results above demonstrate that photovoltaic performance can be improved by introducing suitable heterocyclic groups to triarylamine dyes. A series of properties were investigated to explain the results, with a special emphasis on the geometric structures, energetics, and charge transfer processes at the dye/titania/electrolyte interface.     

Electrochemical and optical characterization of triarylamine functionalized gold nanoparticles

This paper describes the synthesis, structural analysis, and investigations of the optical and electrochemical properties of some gold nanoparticles (AuNPs) which consist of a triarylamine ligand shell attached to small gold cores (Au-Tara). The triarylamine chromophores were attached to small 4-bromobenzenethiol covered gold nanoparticles (ca. 2 nm in diameter) by Sonogashira reaction. This procedure yields triarylamine redox centers attached via π-conjugated bridging units of different length to the gold core. The AuNPs were analyzed with (1)H NMR spectroscopy, diffusion ordered NMR spectroscopy (DOSY), thermogravimetric analysis (TGA), and scanning transmission electron microscopy (STEM). Cyclic voltammetry (CV) technique was used to determine the composition of the redox active particles via the Randles-Sevcik equation. The optical and electrochemical properties of the Au-Tara nanoparticles and of their corresponding unbound ligands (Ref) were investigated with UV/vis/NIR absorption spectroscopy, Osteryoung square wave voltammetry (OSWV), and spectroelectrochemistry (SEC). These data show that the assembling of triarylamines in the vicinity of a gold nanoparticle can change the optical and electrochemical properties of the triarylamine redox chromophores depending on the kind and length of the bridging unit. This is due to gold core-chromophore and chromophore-chromophore interactions.     

具有高分子空穴传输性能的含三芳胺侧链接枝聚苯乙烯的合成与表征

三芳胺类聚合物作为空穴传输材料具有广泛的应用前景。设计、合成了一种新的三芳胺衍生物单体 4 -乙烯基苄氧基亚甲基三苯胺 ,通过NMR、IR及MS等手段对其结构进行了表征。用AIBN引发新单体进行自由基聚合反应 ,得到了侧链带三苯胺基团的高分子空穴传输聚合物 ,该聚合物具有较高玻璃化转变温度及高热稳定性。     

Heterogeneous electron transfer processes in self-assembled monolayers of amine terminated conjugated molecular wires

A versatile synthesis of triarylamine and phenothiazine end-capped oligo(phenyleneacetylene) molecular wires which are terminated by thiol functions is described. The repetitive synthesis allows the preparation of molecular wires with different chain length and different substituents attached to the wire backbone. These molecular wires were used to form dense self-assembled monolayers (SAM) on gold substrates as proved by cyclic voltammetry and quartz crystal microbalance measurements. The heterogeneous electron transfer rate constant of these SAMs was measured by impedance spectroscopy between 1 MHz and 0.1 Hz. The rate constants are somewhat larger for the triarylamine terminated systems than for the phenothiazine compound, due to the higher reorganization energy in the latter. While the molecular wires with electron withdrawing substituents display an electron transfer which is slow enough to be measurable with our impedance setup, we were unable to determine the rate of molecular wires with electron donating substituents.     

2.2]paracyclophane-bridged mixed-valence compounds: application of a generalized Mulliken-Hush three-level model

A series of [2.2]paracylophane-bridged bis-triarylamine mixed-valence (MV) radical cations were analyzed by a generalized Mulliken-Hush (GMH) three-level model which takes two transitions into account: the intervalence charge transfer (IV-CT) band which is assigned to an optically induced hole transfer (HT) from one triarylamine unit to the second one and a second band associated with a triarylamine radical cation to bridge (in particular, the [2.2]paracyclophane bridge) hole transfer. From the GMH analysis, we conclude that the [2.2]paracyclophane moiety is not the limiting factor which governs the intramolecular charge transfer. AM1-CISD calculations reveal that both through-bond as well as through-space interactions of the [2.2]paracyclophane bridge play an important role for hole transfer processes. These electronic interactions are of course smaller than direct pi-conjugation, but from the order of magnitude of the couplings of the [2.2]paracyclophane MV species, we assume that this bridge is able to mediate significant through-space and through-bond interactions and that the cyclophane bridge acts more like an unsaturated spacer rather than a saturated one. From the exponential dependence of the electronic coupling V between the two triarylamine localized states on the distance r between the two redox centers, we infer that the hole transfer occurs via a superexchange mechanism. Our analysis reveals that even significantly longer pi-conjugated bridges should still mediate significant electronic interactions because the decay constant beta of a series of pi-conjugated MV species is small.     

Electron-rich tetrathiafulvalene-triarylamine conjugates: synthesis and redox properties

By combining tetrathiafulvalenes (TTFs) and triarylamines, four TTF-triarylamine conjugates bridged by an annulated pyrrole ring were designed and synthesized by an N-arylation reaction. Electrochemical and photophysical investigations suggest that these novel conjugates possess very strong electron-donating ability with very high HOMO energy levels of around -4.70 eV; the HOMOs are mainly located on the TTF moiety. We observed significant electronic coupling between the TTF moieties and the triarylamine groups. However, no evidence for such electronic communication between end-capping TTF units (conjugates 5 and 7) or between two terminal triarylamine groups (conjugate 9) could be found. Differential scanning calorimetry (DSC) measurements together with PM3-optimized geometries suggest that conjugates 5 and 7, which adopt three-dimensional propeller-shaped structures, may easily pack and crystallize in the solid state because of the large rigid planar blades consisting of TTF and one of the phenyl rings of the triarylamine moiety. However, conjugate 9, with two bulky end-capping triarylamine groups, forms an amorphous material with a glass transition at 74.5 degrees C.     

Triarylamine-combined nitronyl nitroxide and its hole-transporting property

N,N-Bis(4-methoxyphenyl)-4-(1-oxyl-3-oxide-4,4,5,5-tetramethylimidazolin-2-yl)phenylamine (1) was synthesized as a durable nitronyl nitroxide radical combined with a triarylamine moiety. Cyclic voltammetry and UV–Vis absorption spectra during the electrochemical oxidation of 1 revealed that the first redox was derived from the triarylamine moiety. The ionization potential of 1 was measured by photoelectron spectroscopy to be −5.4 eV, which was appropriate as a hole-transporting material. A single-layer hole-only device was fabricated with the radical molecule 1 dispersed in polycarbonate (ITO/1:polycarbonate/Al): The radical-layer exhibited a maximum current density of 0.2 mA/cm², which was applicable for organic electronic devices.     

Syntheses and spectroscopic studies of spirobifluorene-bridged bipolar systems; photoinduced electron transfer reactions

Some 9,9'-spirobifluorene-bridged bipolar systems 1-3 containing 1,3,4-oxadiazole-conjugated oligoaryl and triarylamine moieties have been synthesized, in which 1 exhibits remarkable solvent-polarity dependent fluorescence properties due to a highly efficient photoinduced electron transfer reaction.     

三芳胺合成的研究进展

三芳胺化合物的合成方法主要有3种:(1)非金属催化的胺化反应;(2)铜催化的Ullnann反应,包括使用过量铜粉为催化剂的传统的Ullmann反应、使用相转移催化剂的Ullmann反应以及使用配体的post-Ullmann反应;(3)钯催化的Buchwald-Hartwig反应.该类反应活性的关键是配体的选择,根据配体结构的不同可分为双膦螯合型配体、单膦配体和非膦配体.对该类化合物的这几种合成方法的研究进展进行了总结.     

An unpaired electron-based hole-transporting molecule: triarylamine-combined nitroxide radicals

A durable nitroxide radical combined with a triarylamine moiety exhibited a hole-drift mobility of 6 x 10(-3) cm(2) V(-1) s(-1), to which the aminophenyl nitroxide structure contributed.     

Porphyrin-triarylamine conjugates: strong electronic communication between triarylamine redox centers via the porphyrin dication

A set of porphyrin-triarylamine hybrids have been synthesized in good yield by Sonogashira palladium-catalyzed cross-coupling reactions between the zinc complex of 5,15-diethynyl-10,20-dimesitylporphyrin and the appropriate iodophenyldiarylamines. The crystal structure of porphyrin 1 shows that the dihedral angle between the acetylene-bonded benzene rings and the porphyrin macrocycle is 20.0 degrees. Such a structural characteristic enables effective electronic perturbations within the molecule. The electronic spectra are red-shifted and display a broad Soret band and an intense Q band relative to those of meso-substituted tetraarylporphyrins. These conjugates display four oxidations and one reduction. All the electrochemical reactions involve one-electron transfer. The first and second oxidations are reversible and can be assigned to the porphyrin-centered reactions. The third and fourth ones, separated by about 270 mV, correspond to the triarylamine units. The comproportionation constant (Kc) is calculated to be 3.67x10(4). The electron coupling between the triarylamine moieties, at a separation of >23 A, is remarkably strong. The electrochemical results and the absorption spectra show that the electronic characteristics of these porphyrins can be significantly modulated by the triarylamine substituents via the conjugated carbon-carbon triple bond. Variations of the substituents on the triarylamines can fine-tune the electronic properties of these molecules.     

Optically and thermally induced electron transfer pathways in hexakis[4-(N,N-diarylamino)phenyl]benzene derivatives

The optically and thermally induced electron transfer pathways of highly symmetrical (D(3)) hexaarylbenzene systems with six triarylamine redox sites have been investigated. Owing to slightly different local redox potentials, the radical trication could be selectively generated by electrochemical methods. This trication shows a strong intervalence charge-transfer band in the near infrared (NIR) that was measured by spectroelectrochemistry and analysed using multi-dimensional Mulliken-Hush theory. Quantum chemical AM1 CI calculations indicate that there is no optically induced concerted three-electron transfer that transforms the ground state into a state in which all three positively charged triarylamine moieties change place with their neutral neighbours. The potential energy surface of the ground state was constructed by using quadratic potentials. From this potential surface it is apparent that there is also no thermally allowed concerted three-electron transfer pathway. Instead, three consecutive one-electron transfer steps are necessary for this process.     

Electrogenerated chemiluminescence. 81. Influence of donor and acceptor substituents on the ECL of a spirobifluorene-bridged bipolar system

The electrochemistry and radical ion annihilation electrogenerated chemiluminescence (ECL) of 9,9'-spirobifluorene-bridged bipolar systems containing 1,3,4-oxadiazole-conjugated oligoaryl and triarylamine substituents were investigated. The stability of the oxidized spirobifluorenes was improved by functionalization with triarylamine centers. These donor-acceptor (DA) compounds exhibited a good fluorescence efficiency with an emission maximum that correlated with the potential difference between radical anion and cation formation, suggesting a charge transfer (CT) emission band. An ECL mechanism based on the formation of the CT excited state by radical ion annihilation or production of the triplet state followed by triplet-triplet annihilation, with perhaps some excimer contribution, is proposed.     

Effect of chenodeoxycholic acid (CDCA) additive on phenothiazine dyes sensitized photovoltaic performance

The effects of chenodeoxycholic acid (CDCA) in a dye solution as a co-adsorbent on the photovoltaic performance of dye-sensitized solar cells (DSSCs) based on two organic dyes containing phenothiazine and triarylamine segments (P1 and P2) were investigated.It was found that the coadsorption of CDCA can hinder the formation of dye aggregates and improve electron injection yield and thus Jsc.This has also led to a rise in photovoltage,which is attributed to the decrease of charge recombination.The DSSC based ...     

Charge-transfer interactions in a multichromophoric hexaarylbenzene containing pyrene and triarylamines

Two different hexaarylbenzenes with three pyrene and three triarylamine substituents in different positions (trigonal symmetric and asymmetric arrangement) were synthesized, and their charge-transfer states were investigated by optical spectroscopy. In these multichromophoric systems triarylamine acts as the electron donor and pyrene as the electron acceptor. A reference chromophore with only one donor-acceptor pair was also investigated. All these chromophores form charge-transfer states upon photoexcitation which relax with a moderate fluorescence quantum yield to the ground state. The compounds do not differ significantly concerning most of their fluorescence properties, which shows that the fluorescent charge-transfer state is very similar in all chromophores. This observation indicates symmetry breaking for the symmetric chromophore within fluorescence lifetime of several tens of ns. This interpretation was substantiated by fluorescence excitation anisotropy measurements in a sucrose octaacetate matrix.     

Synthesis, spectroscopic properties, and electropolymerization of azulene dyads

Four azulene dyads have been synthesized and studied by spectroscopic and electrochemical methods. A triarylamine, a boron-dipyrromethene (BDP or BODIPY), a porphyrin, and an isoalloxazine moiety have been linked to an extended π electron system at the 2-position of azulene, leading to the dyads 1-4, respectively. For the synthesis of 1-4, first 2-(4-ethynyl-phenyl)azulene (EPA) was prepared, which was further reacted with the halogenated chromophores by Pd-catalyzed cross-coupling reactions. The dyads 1-4 exhibit strong absorption bands in the visible range, which are dominated by the absorption spectra of the individual subchromophores. Fluorometric studies of 2-4 revealed that after excitation of the subchromophoric unit attached to the parent azulene moiety, quenching mainly through energy transfer to azulene is effective, whereas possible charge-transfer interactions play only a minor role. Potentiodynamic oxidation of the dyads 1-4 leads to the formation of polymer films, which are deposited at the electrode. The polymer film derived from 1 was further characterized by spectroelectrochemistry. During positive doping of poly-1, a strong absorption band appears at 13,200 cm(-1), which is typical for triarylamine radical cations. This band is overlapping with a broad absorption band in the low-energy region that might be caused by charge-transfer interactions within the polymer.     

Starburst triarylamine donor-acceptor-donor quadrupolar derivatives based on cyano-substituted diphenylaminestyrylbenzene: tunable aggregation-induced emission colors and large two-photon absorption cross sections

In this work, we have developed a new class of aggregation‐induced emission (AIE) active compounds, in which three electron‐donating diphenylamine, phenothiazine, or carbazole groups are connected to the 1, 4‐positions of the benzene through bis(α‐cyano‐4‐diphenylaminostyryl) conjugation bridges to form three triarylamine quadrupolar derivatives ( 3 a – c ). Their one‐ and two‐photon absorption properties have been investigated. The two‐photon absorption (2PA) cross sections measured by the open‐aperture Z‐scan technique were determined to be 1016, 1484, and 814 GM for 3 a – c , respectively. From this result, the high 2PA properties of these molecules are attributed to the extended π system and enhanced intramolecular charge transfer from the starburst triarylamine to the cyano group. Moreover, cyano‐substituted diphenylamine styrylbenzene (CNDPASB)‐based compounds are very weakly fluorescent in THF, but their intensities increase by almost 230, 70, and 5 times, respectively, in water/THF (v/v 90 %) mixtures, in which they exhibit strongly enhanced red, orange, and deep yellow fluorescence emissions, respectively. This result indicates that the intramolecular vibration and rotation of these dyes is considerably restricted in nano‐aggregates formed in water, leading to significant increases in fluorescence. It was found that the color tuning of the CNDPASB‐based compounds could be conveniently accomplished by changing the starburst triarylamine donor moiety. Multilayer electroluminescence devices with TPBI (2,2′,2′′‐(benzene‐1,3,5‐triyl)‐tri(1‐phenyl‐1H‐benzimidazole)) electron‐transporting layers have been made, with 3 a and 3 c as a non‐doping red–yellow emitter. The preliminary results for these multilayer devices show a maximum efficiency of 0.25 %, and electroluminescence (EL) wavelengths around 568 nm. The excellent 2PA and AIE properties of these compounds make them potential materials for biophotonic applications.     

Photoinduced charge transfer processes along triarylamine redox cascades

In this paper, we describe the synthesis and photophysical properties of a series of acridine-triarylamine redox cascades. These cascades were designed in order to promote photoinduced hole transfer from an acridine fluorophore into an adjacent triarylamine. The excited dipolar state then injects a hole into the triarylamine redox cascade. Subsequently, the hole migrates along the redox gradient which was tuned by the substituents attached to the triarylamine redox centers. The rate of hole migration was determined by fluorescence lifetime measurements and is in the ns regime and depends strongly on the solvent polarity. The photophysical processes were also investigated by femtosecond broadband pump-probe spectroscopy. Our studies reveal different dynamic processes in the cascades depending on the solvent polarity, e.g., direct charge separation after photoexcitation vs a two step hole transfer mechanism.     

Photoinduced electron transfer in linear triarylamine-photosensitizer-anthraquinone triads with ruthenium(II), osmium(II), and iridium(III)

A rigid rod-like organic molecular ensemble comprised of a triarylamine electron donor, a 2,2'-bipyridine (bpy) ligand, and a 9,10-anthraquinone acceptor was synthesized and reacted with suitable metal precursors to yield triads with Ru(bpy)(3)(2+), Os(bpy)(3)(2+), and [Ir(2-(p-tolyl)pyridine)(2)(bpy)](+) photosensitizers. Photoexcitation of these triads leads to long-lived charge-separated states (τ = 80-1300 ns) containing a triarylamine cation and an anthraquinone anion, as observed by transient absorption spectroscopy. From a combined electrochemical and optical spectroscopic study, the thermodynamics and kinetics for the individual photoinduced charge-separation and thermal charge-recombination events were determined; in some cases, measurements on suitable donor-sensitizer or sensitizer-acceptor dyads were necessary. In the case of the ruthenium and iridium triads, the fully charge-separated state is formed in nearly quantitative yield.